Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Analog sandbox models have been set up to study the impact of syntectonic erosion on thrust wedges with one and two decollement levels. Different accretion mechanisms are activated depending on interactions between surface processes and wedge mechanics: frontal accretion, backthrusting, underthrusting and underplating due to decollement induced duplex formation at depth. These mechanisms may function simultaneously, being located at different parts across the wedge. For all the experiments, a high friction is imposed at the base of models and the volume of eroded material remains equal to the volume of newly accreted material, maintaining a constant surface slope during the shortening. Erosion limits the forward propagation of thrust wedges and favors the underthrusting of basal layers allowing duplex formation. Erosion promotes development of major backthrusts in the thrust wedges without or with one decollement, but no backthrusts was formed in the wedges with two decollements. Slow erosion allows lower extent of basal underthrusting in comparison with regular-rate erosion. Variations in the erosion taper lead to changes in duplex geometry and exhumation rate in thrust wedges with one or two decollements. The 6 degrees erosion taper promotes formation of antiformal stack at the rear part of thrust wedge, high rate of basal underthrusting and high extent of erosional removal. The cover layers are nearly completely eroded above the antiformal stack and form the synformal klippe in frontal part of thrust wedges. The 8 degrees erosion taper allows development of individual ramp-anticlines and active forward thrusting of cover layers above the decollement and low rate of basal underplating below it, with consequent low extent of erosional removal. The results of our experiments support the observations on structural evolution and erosion in the Alberta Foothills of the Canadian Rockies.
ISSN: 0040-1951

hal-00617769
https://hal.archives-ouvertes.fr/hal-00617769
DOI : 10.1016/j.tecto.2011.01.020

Éditeur(s) : HAL CCSD Geological Society
Résumé : International audience
Deformation mechanisms, long-term kinematics and evolution of fold and thrust belts subjected to erosion are studied through 2D analogue experiments involving large convergence. First-order parameters tested include (1) décollements and/or plastic layers interbedded at different locations within analogue materials and (2) synconvergence surface erosion. Weak layers, depending on their location in the model, favour deformation partitioning characterized by the simultaneous development of underplating domains in the inner part of the wedge (basal accretion) and frontal accretion where the wedge grows forward. Interaction between tectonics and surface processes influences this behaviour. Development of antiformal thrust stacks controlled by underplating shows small- and large-scale cyclicity. Thin plastic layers induce folding processes, which are studied at wedge scale. Recumbent and overturned folds, with large inverted limbs, develop in a shear-induced asymmetric deformation regime via progressive unrolling of synclinal hinges. Surface erosion and underplating at depth induce further rotation (passive tilting) and horizontalization of fold limbs. Model results give insights to discuss the mechanisms responsible for the large-scale structures (i.e. antiformal nappe stacks, klippen and kilometre-scale recumbent fold-nappes) encountered in several mountain belts such as the Montagne Noire (French Massif Central), the Galicia Variscan belt (Spain) and the northern Apennines (Italy).
ISSN: 0016-7649

hal-00937644
https://hal.archives-ouvertes.fr/hal-00937644
DOI : 10.1144/jgs2013-012

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : TECTO LITHO
On the basis of a section across the northwestern Alpine wedge and foreland basin, analogue modeling is used to investigate the impact of surface processes on the orogenic evolution. The basis model takes into account both structural and lithological heritages of the wedge. During shortening, erosion and sedimentation are performed to maintain a critical wedge. Frontal accretion leads to the development of a foreland thrust belt; underplating leads to the formation of an antiformal nappe stack in the internal zones. Important volumes of analogue materials are eroded out of the geological record, which in the case of the Alps suggests that the original lengths and volumes may be underestimated. The foreland basin evolves differently depending on the amounts of erosion/sedimentation. Its evolution and internal structuring is governed by the wedge mechanics, thought to be the main controlling mechanism in the development of the Molasse basin in a feedback interaction with surface processes.
ISSN: 0278-7407

hal-00404424
https://hal.archives-ouvertes.fr/hal-00404424
DOI : 10.1029/2006TC002048