Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Betic-Rif orocline surrounding the Alboran Sea, the westernmost tip of the Mediterranean Sea, accommodates the NW–SE convergence between the Nubia and Eurasia plates. Recent GPS observations indicate a ∼4 mm/yr SW motion of the Rif Mountains, relative to stable Nubia, incompatible with a simple two-plate model. New gravity data acquired in this study define a pronounced negative Bouguer anomaly south of the Rif, interpreted as a ∼40 km-thick crust in a state of non-isostatic equilibrium. We study the correlation between these present-day kinematic and geodynamic processes using a finite-element code to model in 2-D the first-order behavior of a lithosphere affected by a downward normal traction (representing the pull of a high-density body in the upper mantle). We show that intermediate viscosities for the lower crust and uppermost mantle (View the MathML source1021–1022Pas) allow an efficient coupling between the mantle and the base of the brittle crust, thus enabling (1) the conversion of vertical movement, resulting from the downward traction, to horizontal movement and (2) shortening in the brittle upper crust. Our results show that incipient delamination of the Nubian continental lithosphere, linked to slab pull, can explain the present-day abnormal tectonics, contribute to the gravity anomaly observed in northern Morocco, and give insight into recent tectonics in the Western Mediterranean region.
ISSN: 0012-821X

hal-01467130
https://hal.archives-ouvertes.fr/hal-01467130
DOI : 10.1016/j.epsl.2016.08.041

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Temperature and fluid pressure conditions control rock deformation and mineralization on geological faults, and hence the distribution of earthquakes1. Typical intraplate continental crust has hydrostatic fluid pressure and a near-surface thermal gradient of 31 ± 15 degrees Celsius per kilometre2, 3. At temperatures above 300–450 degrees Celsius, usually found at depths greater than 10–15 kilometres, the intra-crystalline plasticity of quartz and feldspar relieves stress by aseismic creep and earthquakes are infrequent. Hydrothermal conditions control the stability of mineral phases and hence frictional–mechanical processes associated with earthquake rupture cycles, but there are few temperature and fluid pressure data from active plate-bounding faults. Here we report results from a borehole drilled into the upper part of the Alpine Fault, which is late in its cycle of stress accumulation and expected to rupture in a magnitude 8 earthquake in the coming decades4, 5. The borehole (depth 893 metres) revealed a pore fluid pressure gradient exceeding 9 ± 1 per cent above hydrostatic levels and an average geothermal gradient of 125 ± 55 degrees Celsius per kilometre within the hanging wall of the fault. These extreme hydrothermal conditions result from rapid fault movement, which transports rock and heat from depth, and topographically driven fluid movement that concentrates heat into valleys. Shear heating may occur within the fault but is not required to explain our observations. Our data and models show that highly anomalous fluid pressure and temperature gradients in the upper part of the seismogenic zone can be created by positive feedbacks between processes of fault slip, rock fracturing and alteration, and landscape development at plate-bounding faults.
ISSN: 0028-0836

hal-01685757
https://hal.archives-ouvertes.fr/hal-01685757
DOI : 10.1038/nature22355

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We present GravProcess, a set of MATLAB routines to process gravity data from complex campaign surveys and calculate the associated gravity field. Data reduction, analysis, and representation are done using the MATLAB Graphical User Interface Tool, which can be installed on most systems and platforms. Data processing is divided into several steps: (1) Integration of gravity data, station location, and gravity line connection input files; (2) Gravity data reduction applying solid-Earth tide and instrumental drift corrections and, depending on the required processing level, air pressure and oceanic tidal corrections; (3) Automatic network adjustment and alignment to absolute base stations; (4) Free air and terrain corrections to calculate gravity values and anomalies, and to estimate the associated errors. The final step is dedicated to post-processing and includes graphical representations of data and an output text file, which can be used by Geographic Information System software. An example of this processing chain applied to a recent survey in northern Morocco is given and compared with previous available results.
ISSN: 0098-3004

hal-01217120
https://hal.archives-ouvertes.fr/hal-01217120
DOI : 10.1016/j.cageo.2015.04.005