Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
The objective of this study was to realize a three-dimensional (3-D) geological model of the deep basin structure of the Middle Durance region (of folds and faults) by integration of geological and geophysical data, and to evaluate its fault geometry and tectonic history. All of the available geophysical and geological data were compiled in three dimensions using the gOcad geomodeler. The geological and geophysical data were used to build a 3-D geological model of the Middle Durance region. The data on the 3-D geometry of fault surfaces and stratigraphic horizons and the thickness maps of the main stratigraphic units are supported by the 3-D geological model. We show that the Middle Durance Fault cannot be interpreted as a single fault plane that affected the entire Meso-Cenozoic sedimentary layers and the Paleozoic basement but as a listric segmented faulting system in sedimentary layers, rooted in Triassic evaporites and a normal block faulting system in the basement. This decoupling level in the Triassic layers reveals thin-skin deformation, formed by strong mechanical decoupling between the Mesozoic sedimentary cover and the Paleozoic basement. This study also confirms that the Provence geological structure has resulted mainly from Pyrenean deformation, which was partly reactivated by Alpine deformation. We demonstrate that the Middle Durance Fault Zone is a transfer fault that accommodates deformation of the sedimentary filling of the South-East Basin through modified fold geometry over a zone of 7 km to 8 km around the main segment of the fault zone.
ISSN: 0278-7407

hal-01172221
https://hal.archives-ouvertes.fr/hal-01172221
DOI : 10.1002/2014TC003749

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Thermal diffusivity of synthetic quartz single-crystals and natural polycrystalline aggregates were measured using a modified Angstrom method at ambient pressure and up to 800 degrees C in order to investigate the effect of crystal preferred orientation on thermal diffusivity of quartz rich rocks. The thermal diffusivity tensor of quartz was determined by measuring the thermal diffusivity of an oriented synthetic quartz single-crystal along the [100] and [001] directions. A naturally deformed, fine-grained quartzite mylonite, was used to compare the single crystal properties with aggregate properties. Using the crystal preferred orientations (CPO) measured by the Electron Back Scattered Diffraction (EBSD) method and the measured thermal diffusivity tensor of quartz, the three-dimensional aggregate thermal diffusivity was modelled using volume averaging models. In order to test the validity of these models that are only based on the properties of the constituent minerals, the thermal diffusivity was then measured on oriented cores as a function of temperature, along three orthogonal directions, parallel to the (X-lineation, Y, Z-pole to foliation) structural frame. Both modelled and direct measurement of thermal diffusivity show an anisotropy of thermal diffusivity, heat transport being more effective parallel to Y-direction and less effective parallel to the lineation X-direction. Thermal diffusivities measured in a given direction on the natural rock are lower by less than 10% than the modelled thermal diffusivity in the same direction, showing that rock imperfections have a weak effect on heat transport. In addition, the modelled thermal diffusivity anisotropy based on the characterization of crystal orientations and thermal diffusivity tensor shows a good agreement with measurements in both alpha and beta stability field. This validation of the petrophysical simulation allows for evaluating the 3D thermal diffusivity of quartz rich rocks in different crustal conditions. The 3D thermal diffusivity of five naturally deformed quartzites displaying quartz fabrics expected in different crustal pressure and temperature ranges were simulated. The resulting thermal diffusivity anisotropies of quartzites range between 40% and 10%, depending on temperature, crystallographic fabric patterns and fabric strength. Under crustal conditions, quartzites deformed in the granulite facies display a high thermal diffusivity in the (XZ) foliation plane, whereas quartzites deformed in greenschist facies have highest thermal diffusivity in the (Z) direction normal to the foliation plane.
ISSN: 0040-1951

hal-00413568
https://hal.archives-ouvertes.fr/hal-00413568
DOI : 10.1016/j.tecto.2008.11.006

Résumé : Une étude de faisabilité de poutres en bois lamellé-collé a été menée en Guyane Française en utilisant les essences locales. Le but est de déterminer les paramètres de collage assurant la bonne résistance mécanique des assemblages par lamellation et par aboutage, nécessaires à la fabrication de poutres en bois lamellé-collé en climat tropical. Trois essences de bois abondantes de différentes densités ont été sélectionnées. Les adhésifs de types Mélamine-Urée-Formol et Résorcinol-Phénol-Formol ont été utilisées. Les paramètres de collage considérés sont : le grammage, le temps d’assemblage fermé et la pression.En utilisant les normes Européennes, plusieurs campagnes de tests ont été conduites sur des échantillons normalisés. Concernant le collage par lamellation, des tests élémentaires de délamination et de cisaillement des joints de colle ont été réalisés. Le test de délamination consiste en deux cycles d’immersion dans l’eau sous pression et de séchage, il induit de sévères variations d’humidité du bois susceptibles de créer des ouvertures des joints de colles. Le collage par aboutage est réalisé sur des poutres normalisées aboutées. Les entures sont obtenues grâce à un outillage standard communément utilisé pour les résineux. Les résultats ont mis en évidence l’influence des propriétés du bois et des paramètres de collage sur la résistance du joint et la résistance mécanique du produit. En effet, les paramètres du bois, tels que la densité, la rétractibilité et l’imprégnation, ont une forte influence sur le collage, en particulier sur la pression et le grammage nécessaires à la production d’un produit commercialisable. Il apparait qu’un bois de densité moyenne et poreux nécessite un grammage et une pression élevés comparé à un bois de densité élevée qui nécessite des valeurs moindres. Aussi, l’influence d’autres paramètres de fabrication, tels que le rabotage, l’encollage double face et simple face ainsi que l’épaisseur des lamelles, a été établie. Par contre il semblerait que le matériel communément utilisé pour l’aboutage des résineux n’est pas adapté aux feuillus tropicaux. En final, des paramètres de collage ont été validés pour la fabrication de lamellé-collé endémique en Guyane Française et une étude du coût de production d’une poutre lamellé-collé standard a identifié les conditions économiques d’une fabrication en Guyane Française.
A feasibility study of glued-laminated timber beams was carried out in French Guiana using local wood species. The aim of the study was to evaluate the gluing parameters that could ensure good mechanical properties for the manufactured glued-laminated beams in tropical climates. Three abundant wood species with different specific gravity were selected for the study. Melamine-Urea-Formaldehyde and Resorcinol-Phenol-Formaldehyde resins were used for gluing. The three gluing parameters considered are: adhesive spread rate, closing assembly time and gluing pressure.Using European standards, several laboratory tests were performed on normalized samples. The evaluation of a successful lamella’s gluing was done by using elementary tests of delamination and shearing. A delamination test consists of two cycles of water immersion at high pressure and drying which induces severe hygroscopic variation in wood thus causing joints opening. The finger-joints are made using a standard tool usually used for cutting softwoods. The performed tests revealed the influence of wood properties and the gluing parameters on the joint resistance and the mechanical properties of the product. Results show that wood properties such as specific gravity, shrinkage coefficient, and permeation, have a high degree of influence on the gluing step especially on the gluing pressure and on the adhesive spread rate needed to produce a commercial product. Furthermore, wood with medium specific gravity needs more adhesive and more pressure than the one with high specific gravity. Additionally, the effects of other manufacturing parameters, such as planning, double or simple side glue spreading and lamellae thicknesses, on the glue joint resistance were demonstrated. Finally, the common tools used for softwoods are not adapted to making the finger joints with tropical hardwoods.In conclusion, optimal gluing parameters for manufacturing glued-laminated timber beams in French Guiana were established and an economical study using standard glued-laminated timber beams revealed the economic conditions under which a successful manufacturing of these local beams can be implemented in French Guiana.

http://www.theses.fr/2011AGUY0484/document

Éditeur(s) : HAL CCSD
Résumé : The territory of Armenia was located in the collision zone between Arabia and Eurasia, and is the seat of active intercontinental deformations, which was attested by the many historical earthquakes that have occurred in this region. All these destructive earthquakes show a strong regional seismic activity, and therefore it is important to evaluate the seismic hazard associated with active structures that generates this seismicity.This study presents the results of the analysis of the active tectonics within the northwestern and southeastern extensions of the Pambak-Sevan-Syunik fault (PSSF), a major right-lateral strike-slip fault cutting through Armenia (NW - SE). Quantifying the deformations in terms of geometry, kinematics, slip rates and earthquake activity, using cosmogenic 3He, OSL/IRSL and radiocarbon dating techniques, reveal different behaviors between the two regions.Within the northwestern extension, in the region of Amassia, the PSSF bends to the west and splits into two main WNW-ESE trending reverse faults defining a compressional pop-up structure. We estimate an uplift rate and a shortening rate of 0.5 ± 0.1 mm/y and 1.4 ± 0.6 mm/y, respectively. This suggests that most of the ~2 mm/y right lateral movement of the PSSF seems to be absorbed within the Amasia pop-structure.Within the southeastern extension, in the region of Tsghuk volcano, the PSSF shows signs of dying out at the southernmost tip of the Syunik graben. A very slow NS trending normal faulting associated with a slight right-lateral movement characterizes the tectonic activity in the region of Tsghuk volcano. We estimate vertical slip rates, EW stretching rate, and right-lateral slip rate of ~0.2 mm/y, ~0.1 mm/y and ~0.05 mm/y, respectively. These results lead to the conclusion that the right lateral movement observed further north along the PSSF is mainly transferred within other active faults further west within the Karabagh (Hagari fault or other structures further northwestwards).
L’Arménie se situe dans la zone de collision entre Arabie et Eurasie et est le siège d’une déformation intracontinental active comme l’atteste les nombreux tremblements de terre historiques qui s’y sont produits. Tous ces séismes, destructeurs, attestent d’une forte activité sismique régionale, et il est par conséquent important d'évaluer l’aléa sismique associé aux structures actives qui génère cette sismicité.Le travail présenté ici, expose les résultats de l’analyse de la tectonique active au niveau des terminaisons nord-ouest et sud-est de la faille de Pambak-Sevan-Syunik (PSSF), une des failles décrochant majeure qui traverse l'Arménie du NW au SE. La quantification des déformations en termes de géométrie, cinématique, vitesse de glissement et paléosismicité, en utilisant les méthodes de datation 3He cosmogénique, OSL/IRSL et radiocarbone, révèlent des comportements différents entre les deux régions.Au niveau de la terminaison nord-ouest, dans la région d’Amassia, la faille PSSF s’incurve vers l'ouest et se subdivise en deux branches de direction WNW-ESE, et de cinématique inverse, définissant une structure en pop-up. Nous estimons une vitesse de soulèvement de 0.5 ± 0.1 mm/an et une vitesse de raccourcissement NNE-SSW de 1.4 ± 0.6 mm/an. Ces résultats suggère que l’essentiel des ~2 mm/an de mouvement dextre estimés le long de la faille de PSSF sont absorbés au niveau du pop-up d’Amassia.Au niveau de la terminaison sud-est, dans la région du volcan Tsghuk, la faille PSSF semble disparaitre. Le peu d’activité tectonique est caractérisée par des failles normales sub-méridiennes associées à une légère composante décrochant dextre. Nous déterminons une vitesse de glissement vertical de ~0,2 mm/an, une vitesse d’extension ~EW de ~0,1 mm/an associée à une composante dextre de ~0,05 mm/an. Ces résultats suggèrent que le mouvement dextre observé le long de la faille de PSSF plus au nord, a été transféré sur d'autres failles plus à l'ouest dans le Karabakh (faille Hagari ou autres structures situés encore plus au NW).
https://tel.archives-ouvertes.fr/tel-01621440

NNT : 2016MONTT152
tel-01621440
https://tel.archives-ouvertes.fr/tel-01621440
https://tel.archives-ouvertes.fr/tel-01621440v2/document
https://tel.archives-ouvertes.fr/tel-01621440/file/2016_MKRTCHYAN_archivage.pdf