Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In petroleum industry, the difference between pore pressure (Pp) and minimum horizontal stress Sh (termed the seal or retention capacity) is of major consideration because it is often assumed to represent how close a system is to hydraulic failure and thus the maximum hydrocarbon column height that can be maintained. While Sh and Pp are often considered to be independent parameters, several studies in the last decade have demonstrated that Sh and Pp are in fact coupled. However, the nature of this coupling relationship remains poorly understood. In this paper, we explore the influences of the spatial pore pressure distribution on Sh/Pp coupling and then on failure pressure predictions and trap integrity evaluation. With analytical models, we predict the fluid pressure sustainable within a reservoir before failure of its overpressured shale cover. We verify our analytical predictions with experiments involving analogue materials and fluids. We show that hydraulic fracturing and seal breach occur for fluid pressure greater than it would be expected from conventional retention capacity. This can be explained by the impact of the fluid overpressure field in the overburden and the pressure diffusion around the reservoir on the principal stresses. We calculate that supralithostatic pressure could locally be reached in overpressured covers. We also define the retention capacity of a cover (RC) surrounding a fluid source or reservoir as the difference between the failure pressure and the fluid overpressure prevailing in shale at the same depth. In response to a localized fluid pressure rise, we show that the retention capacity does not only depend on the pore fluid overpressure of the overburden but also on the tensile strength of the cover, its Poisson's ratio, and the depth and width of the fluid source.
ISSN: 0264-8172

hal-00590497
https://hal.archives-ouvertes.fr/hal-00590497
DOI : 10.1016/j.marpetgeo.2010.08.007

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Large sand intrusions often exhibit conical morphologies analogous to magmatic intrusions such as saucer-shaped or cup-shaped sills. Whereas some physical processes may be similar, we show with scaled experiments that the formation of conical sand intrusions may be favoured by the pore-pressure gradients prevailing in the host rock before sand injection. Our experiments involve injecting air into a permeable and cohesive analogue material to produce hydraulic fractures while controlling the pore pressure field. We control the state of overpressure in the overburden by applying homogeneous basal pore pressure, and then adding a second local pore pressure field by injecting air via a central injector to initiate hydraulic fractures near the injection point. In experiments involving small vertical effective stresses (small overburden, or high pore fluid overpressure), the fracturing pressure (lambda(fract)) is supralithostatic and two dipping fractures are initiated at the injection point forming a conical structure. From theoretical considerations, we predict that high values of lambda(fract), are due to strong cohesion or high pore fluid overpressure distributed in the overburden. Such conditions are favoured by the pore pressure/stress coupling induced by both pore pressure fields. The dips of cones can be accounted for elastic-stress rotation occurring around the source. Contrary to magmatic chamber models, the aqueous fluid overpressure developed in a parent sandbody (and prevailing before the formation of injectites) may diffuse into the surrounding overburden, thus favouring stress rotation and the formation of inclined sheets far from the parent source. For experiments involving higher vertical effective stresses (thick overburden or low pore fluid overpressure), the fracturing pressure is lower than the lithostatic stress, and a single fracture is opened in mode I which then grows vertically. At a critical depth, the fracture separates into two dilatant branches forming a flat cone. We make use of a P.I.V. (Particle Imaging Velocimetiy) technique to analyse plastic deformation, showing that these inclined fractures are opened in mixed modes. Close to the surface, they change into steep shear bands where fluids can infiltrate. The final morphology of the fracture network is very similar to the common tripartite architecture of various injection complexes, indicating that different mechanisms may be involved in the formation of dykes. Feeder dykes under the sill zones may open as tensile fractures, while overlying dykes may be guided by the deformation induced by the growth of sills. These deformation conditions may also favour the formation of fluid escape structures and pockmarks. (C) 2011 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00745640
https://hal.archives-ouvertes.fr/hal-00745640
DOI : 10.1016/j.epsl.2011.10.029