Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In petroleum industry, the difference between pore pressure (Pp) and minimum horizontal stress Sh (termed the seal or retention capacity) is of major consideration because it is often assumed to represent how close a system is to hydraulic failure and thus the maximum hydrocarbon column height that can be maintained. While Sh and Pp are often considered to be independent parameters, several studies in the last decade have demonstrated that Sh and Pp are in fact coupled. However, the nature of this coupling relationship remains poorly understood. In this paper, we explore the influences of the spatial pore pressure distribution on Sh/Pp coupling and then on failure pressure predictions and trap integrity evaluation. With analytical models, we predict the fluid pressure sustainable within a reservoir before failure of its overpressured shale cover. We verify our analytical predictions with experiments involving analogue materials and fluids. We show that hydraulic fracturing and seal breach occur for fluid pressure greater than it would be expected from conventional retention capacity. This can be explained by the impact of the fluid overpressure field in the overburden and the pressure diffusion around the reservoir on the principal stresses. We calculate that supralithostatic pressure could locally be reached in overpressured covers. We also define the retention capacity of a cover (RC) surrounding a fluid source or reservoir as the difference between the failure pressure and the fluid overpressure prevailing in shale at the same depth. In response to a localized fluid pressure rise, we show that the retention capacity does not only depend on the pore fluid overpressure of the overburden but also on the tensile strength of the cover, its Poisson's ratio, and the depth and width of the fluid source.
ISSN: 0264-8172

hal-00590497
https://hal.archives-ouvertes.fr/hal-00590497
DOI : 10.1016/j.marpetgeo.2010.08.007

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
Large-scale conical and saucer-shaped sand injectites have been identified in the Upper Miocene sediments of the Lower Congo Basin. These structures are evidenced on the 3D high-resolution seismic data at about 600 ms TWT (two-way traveltime) beneath the seabed. The conical and saucer-shaped anomalies range from 20 to 80 m in height, 50 to 300 m in diameter, and 10 to 20 ms TWT in thickness. They are located within a sedimentary interval of about 100 m in thickness and are aligned over 20 km in dip direction (NE-SW), above the NW margin of an underlying Upper Miocene submarine fan. We have interpreted the conical and saucer-shaped anomalies as upward-emplaced sand injectites sourced from the Upper Miocene fan because of their discordant character, the postsedimentary uplifting of the sediments overlying the cones and saucer-shaped bodies, the alignment with the lateral fringe of the Upper Miocene submarine fan, and the geological context. Sand injection dates from the Miocene-Pliocene transition (approximately 5.3 Ma). The prerequisite overpressure to the sand injection process may be due to the buoyancy effect of hydrocarbons accumulated in the margins of the fan. Additionally, overpressure could have been enhanced by the lateral transfer of fluids operating in the inclined margins of the lobe. The short duration of sand injection and the presence of many sandstone intrusions suggested that the process of injection was triggered by an event, likely due to a nearby fault displacement related to diapiric movements. This is the first time that sand injectites of seismic scale have been described from the Lower Congo Basin. The localized nature of these injectites has led to a change in the migration path of fluids through the sedimentary cover. Consequently, the sand intrusions are both evidence and vectors of fluid migration within the basin fill.
ISSN: 1468-8115

hal-00963594
https://hal.archives-ouvertes.fr/hal-00963594
DOI : 10.1111/gfl.12057

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
3D seismic data located in the Gjallar Ridge (Vøring Basin, offshore Norway) reveals a closely-spaced polygonal fault system affecting more than 800 m of homogeneous mud-dominated Quaternary and Tertiary sequences. As some faults reach the modern seafloor, they represent an active polygonal fault system at present day. Even if the processes remain unclear and are still under debate, it is generally agreed that the initiation of polygonal faults is the result of shallow burial dewatering of fine-grained unconsolidated sediments by volumetric compaction. 3D seismic data are commonly interpreted by propagating horizons automatically and by picking faults manually. However, in the case of polygonal fault intervals, this approach is time consuming due to the huge number of faults and because automatic propagation can be misleading. In this study, we applied a new technique of 3D seismic interpretation based on a sequential stratigraphy analysis, using the new PaleoScan© software (Eliis Company). It allowed us to build a 3D geological model computing more than 300 horizons within the faulted intervals. We then used the coherency attribute, depicting anomalies in the shape of seismic waveform like faults, in order to constrain a possible link between fault distribution and stratigraphic levels. Our approach allows fault throws to be calculated in milliseconds on any polygonal fault plane. The result shows that fault segments have been reactivated by dip-linkage. Distribution of faults depends on mechanical units, intervals characterized by different petrophysical properties, which are independent from lithological and diagenetic changes. According to these results, we propose a model showing the evolution of polygonal fault intervals in which faulting stages are separated by a quiescence phase during burial. A first tier of polygonal faults is initiated at a specific depth, according to the Cam-clay model. Then, following a period of quiescence during which mud-rich sediments continued to accumulate, new fault segments are initiated above the first mechanical unit and within this undeformed interval. New nucleated faults then connect downward to pre-existing underlying polygonal fault system, thus progressively increasing the thickness of the faulted interval.
ISSN: 0025-3227

hal-00772470
https://hal.archives-ouvertes.fr/hal-00772470
DOI : 10.1016/j.margeo.2012.07.016

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
An exploration 3D seismic data set from the Gjallar Ridge off mid-Norway images a giant fluid seep structure 3 × 5 km wide, which connects to late Palaeocene magmatic sills at depth. Two of the pipes that have developed as hydrothermal vents reach all the way to the modern seafloor implying that they either were active much longer than the original hydrothermal activity or have been reactivated. We combine detailed seismic analysis of the northern pipe and sandbox modeling to constrain pipe initiation and propagation. Although both the seismic data and the sandbox models suggest that fluids at depth are focused through a vertical conduit, sandbox models show that fluids ascend and reach a critical depth migration where focused migration abruptly transforms into distributed fluid flow through unconsolidated sediments. This indicates that at this level the sediments are intensely deformed during pipe propagation, creating a V-shaped structure, i.e. an inverted cone at depth and a positive relief anomaly, 5 to 10 m high, at the seafloor, which is clearly identified on 3D seismic data. Comparison of the geometries observed in sandbox modeling with the seismically observed geometries of the Giant Gjallar Vent suggests that the Giant Gjallar Vent may be a proto-fluid seep at an early stage of its development, preceding the future collapse of the structure forming a seafloor depression. Our results imply that the Gjallar Giant Vent can be used as a window into the geological processes active in the deep parts of the Vøring Basin.
ISSN: 0025-3227

hal-00772465
https://hal.archives-ouvertes.fr/hal-00772465
DOI : 10.1016/j.margeo.2012.08.010

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Large sand intrusions often exhibit conical morphologies analogous to magmatic intrusions such as saucer-shaped or cup-shaped sills. Whereas some physical processes may be similar, we show with scaled experiments that the formation of conical sand intrusions may be favoured by the pore-pressure gradients prevailing in the host rock before sand injection. Our experiments involve injecting air into a permeable and cohesive analogue material to produce hydraulic fractures while controlling the pore pressure field. We control the state of overpressure in the overburden by applying homogeneous basal pore pressure, and then adding a second local pore pressure field by injecting air via a central injector to initiate hydraulic fractures near the injection point. In experiments involving small vertical effective stresses (small overburden, or high pore fluid overpressure), the fracturing pressure (lambda(fract)) is supralithostatic and two dipping fractures are initiated at the injection point forming a conical structure. From theoretical considerations, we predict that high values of lambda(fract), are due to strong cohesion or high pore fluid overpressure distributed in the overburden. Such conditions are favoured by the pore pressure/stress coupling induced by both pore pressure fields. The dips of cones can be accounted for elastic-stress rotation occurring around the source. Contrary to magmatic chamber models, the aqueous fluid overpressure developed in a parent sandbody (and prevailing before the formation of injectites) may diffuse into the surrounding overburden, thus favouring stress rotation and the formation of inclined sheets far from the parent source. For experiments involving higher vertical effective stresses (thick overburden or low pore fluid overpressure), the fracturing pressure is lower than the lithostatic stress, and a single fracture is opened in mode I which then grows vertically. At a critical depth, the fracture separates into two dilatant branches forming a flat cone. We make use of a P.I.V. (Particle Imaging Velocimetiy) technique to analyse plastic deformation, showing that these inclined fractures are opened in mixed modes. Close to the surface, they change into steep shear bands where fluids can infiltrate. The final morphology of the fracture network is very similar to the common tripartite architecture of various injection complexes, indicating that different mechanisms may be involved in the formation of dykes. Feeder dykes under the sill zones may open as tensile fractures, while overlying dykes may be guided by the deformation induced by the growth of sills. These deformation conditions may also favour the formation of fluid escape structures and pockmarks. (C) 2011 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00745640
https://hal.archives-ouvertes.fr/hal-00745640
DOI : 10.1016/j.epsl.2011.10.029