Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We measure throw distributions for graben-bounding normal faults from two areas on Mars to investigate fault growth, displacement-length (D-max-L) scaling, and extensional strain using a complementary suite of techniques. Faults in the northern plains are inferred to be restricted at 2-3 km depth, as shown by a transition from linear scaling, with D-max-L ratios of similar to 1 x 10(-3), to nonlinear scaling for faults >50 km long. On the Alba Patera volcano, faults conform to linear Dmax-L scaling, with a Dmax-L ratio of similar to 6 x 10(-3), consistent with more deeply penetrating faults that are not restricted at depth. These grabens accommodate larger extensional strains (similar to 0.84%) than the faults in the northern plains (similar to 0.23%), with a temporal change from regionally distributed to localized deformation and associated increases in D-max-L ratio extensional strain, and perhaps down-dip fault height. The results suggest that both spatial and temporal variations in extensional strain and displacement-length scaling relations, along with fault restriction, are recorded by Martian fault populations. (C) 2009 Elsevier Ltd. All rights reserved.
ISSN: 0191-8141

hal-00420888
https://hal.archives-ouvertes.fr/hal-00420888
DOI : 10.1016/j.jsg.2009.03.016

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
We describe the structure, microstructure, and petrophysical properties of fault rocks from two normal fault zones formed in low-porosity turbiditic arkosic sandstones, in deep diagenesis conditions similar to those of deeply buried reservoirs. These fault rocks are characterized by a foliated fabric and quartz-calcite sealed veins, which formation resulted from the combination of the (1) pressure solution of quartz, (2) intense fracturing sealed by quartz and calcite cements, and (3) neoformation of synkinematic white micas derived from the alteration of feldspars and chlorite. Fluid inclusion microthermometry in quartz and calcite cements demonstrates fault activity at temperatures of 195degC to 268degC. Permeability measurements on plugs oriented parallel with the principal axes of the finite strain ellipsoid show that the Y axis (parallel with the foliation and veins) is the direction of highest permeability in the foliated sandstone (10-2 md for Y against 10-3 md for X, Z, and the protolith, measured at a confining pressure of 20 bars). Microstructural observations document the localization of the preferential fluid path between the phyllosilicate particles forming the foliation. Hence, the direction of highest permeability in these fault rocks would be parallel with the fault and subhorizontal, that is, perpendicular to the slickenlines representing the local slip direction on the fault surface. We suggest that a similar relationship between kinematic markers and fault rock permeability anisotropy may be found in other fault zone types (reverse or strike-slip) affecting feldspar-rich lithologies in deep diagenesis conditions.
ISSN: 0149-1423

hal-00903428
https://hal.archives-ouvertes.fr/hal-00903428
DOI : 10.1306/03071312127

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In this paper, we describe an outcrop to characterize the effect of fracture spacing and type on larger scale effective elasticity, which is measured for the first time in-situ with a Schmidt hammer. The outcrop is dominated by lime mudstones and belongs to the deformation zone of the St Clement fault, in southern France. Our results suggest that small spacing of faults, open fractures and styolites leads to lesser effective Young's modulus, whereas small sealed fracture spacing leads to greater effective Young's modulus. These relationships are compatible with theoretical models of effective elasticity. Using Amadei and Savage (1993) approach, we define a non-linear model that relates Schmidt hammer rebound to spacing by fracture type. A hemisphere with a radius of 40 to similar to 200 cm is the rheological volume characterized by the Schmidt hammer. Results of model inversion demonstrate that variations of Schmidt hammer rebound over the outcrop can be used to estimate fracture type and stiffness. Stiffness of sealed fractures is 2-3 orders of magnitude greater than the stiffness of faults, stylolites and open fractures. This result is consistent with an increase of the rate of interseismic stress build-up of major faults with sealing of fractures in their damage zone.
ISSN: 0191-8141

hal-00669954
https://hal.archives-ouvertes.fr/hal-00669954
DOI : 10.1016/j.jsg.2011.09.009

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
The way faults control upward fluid flow in nonmagmatic hydrothermal systems in extensional context is still unclear. In the Eastern Pyrénées, an alignment of twenty-nine hot springs (29 ∘ C to 73 ∘ C), along the normal Têt fault, offers the opportunity to study this process. Using an integrated multiscale geological approach including mapping, remote sensing, and macro-and microscopic analyses of fault zones, we show that emergence is always located in crystalline rocks at gneiss-metasediments contacts, mostly in the Têt fault footwall. The hot springs distribution is related to high topographic reliefs, which are associated with fault throw and segmentation. In more detail, emergence localizes either (1) in brittle fault damage zones at the intersection between the Têt fault and subsidiary faults or (2) in ductile faults where dissolution cavities are observed along foliations, allowing juxtaposition of metasediments. Using these observations and 2D simple numerical simulation, we propose a hydrogeological model of upward hydrothermal flow. Meteoric fluids, infiltrated at high elevation in the fault footwall relief, get warmer at depth because of the geothermal gradient. Topography-related hydraulic gradient and buoyancy forces cause hot fluid rise along permeability anisotropies associated with lithological juxtapositions, fracture, and fault zone compositions.
ISSN: 1468-8115

hal-01582968
https://hal-brgm.archives-ouvertes.fr/hal-01582968
https://hal-brgm.archives-ouvertes.fr/hal-01582968/document
https://hal-brgm.archives-ouvertes.fr/hal-01582968/file/Taillefer_et_al_Geofluids_2017.pdf
DOI : 10.1155/2017/8190109

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : International audience
Recent mathematical calculations allow us to define set fracture intensity (I), i.e., the amount of rock mass affected by fracture sets, independently of the investigation mode. This parameter, characteristic of each rock mass, is of much interest to describe the mechanical response of the rock mass to external influences. The aim of this work is to apply these mathematical equations on one site using measurements of three distinct fracture sets: (1) on a plane surface, (2) along a scanline, and (3) using borehole imaging, in order to evaluate and explain variability in collected data. Even if the three types of measurements give differences on absolute intensity values, they still define similar trends, i.e., the order of the fracturing impact of joint sets is the same from the three measurement methods, irrespective of the fact that obtained values are quite different from one survey method to another. We discuss the possible origins of these biases.
ISSN: 1435-9529

hal-01121556
https://hal.archives-ouvertes.fr/hal-01121556
DOI : 10.1007/s10064-014-0572-1

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A large sand injectite network is very well exposed in the area of Bevons, Southeast France. The associated sandstone turbiditic channel–fill and the host marls are the Aptian–Albian rocks of the Vocontian Basin. The sand injection network is composed of dykes, sills and sedimentary laccoliths ranging in thickness from mm to pluri–m. The dykes and sills have vertical and horizontal lengths of up to and over 100 m and 1 km, respectively. Outcrop observations show that the architecture and morphology of the sand injectites in the marls is governed by the local stress field during injection, pre–existing faults, the host–rock lithology, compaction, and distance to the potential sand source(s). The main set of dykes is oriented N50–60° perpendicular to the minimum compressive stress σ3 during sand injection. Two other sets of dykes are intruded along pre–existing syn–sedimentary faults oriented N140–150° (set 2) and N90° (set 3) during the Apto–Cenomanian interval. Sills and dykes thin laterally away from their potential sand sources and thin laterally away from them. The vertical thickness variations of the dykes and wings are more complex, as thinning away from the sand sources is often compensated by thickening toward the palaeo–surface. Based on field observations and measurements, we characterized the 3D architecture of the sand injectites and showed that the injectites probably formed due to a forceful injection from an overpressured sand body sealed by low–permeability lithologies.
ISSN: 0191-8141

hal-01243488
https://hal.archives-ouvertes.fr/hal-01243488
DOI : 10.1016/j.jsg.2015.07.001

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We use a strike-slip fault analog model to study experimentally the role played by along-fault non-uniform and asymmetric applied normal stress on both coseismic slip and long-term fault behavior. Our model is based on a visco-elasto-plastic multi-layered rheology that allows to produce several hundreds of scaled analog microquakes and associated seismic cycles. Uniform or heterogeneous applied normal stress along the fault plane is imposed and maintained constant during the whole experiment durations. Our results suggest that coseismic slip patterns are strongly controlled by spatial normal stress variations and subsequent accumulated shear stress along fault strike. Major microquakes occur preferentially in zones of major shear stress asperities. Coseismic slip distributions exhibit a pattern similar to the along-fault applied normal stress distribution. The occurrence of isolated low to moderate microquakes where residual stresses persist around secondary stress asperities, indicates that stress conditions along the fault also control the whole variability of fault slip events. Moreover, when fault slip stability conditions are modulated by normal stress distribution, our experiments suggest that the along-fault stress heterogeneity influences the seismic cycle regularity and, consequently, long-term fault slip behavior. Uniform applied normal stress favors irregular seismic cycles and the occurrence of earthquakes clustering, whereas non-uniform normal stress with a single high amplitude stress asperity generates strong characteristic microquake events with stable return periods. Together our results strengthen the assumption that coseismic slip distribution and earthquake variability along an active fault may provide relevant information on long term tectonic stress and could thus improve seismic hazard assessment.
ISSN: 0012-821X

hal-01666379
https://hal.archives-ouvertes.fr/hal-01666379
DOI : 10.1016/j.epsl.2017.10.009

Éditeur(s) : HAL CCSD
Résumé : International audience
In most rock mechanical testing devices, the texture developed during deformation is only observed after the failure, and the detailed mapping of cracks and pore structure evolution, just before or after rupture, remains speculative. Computerized X-ray tomography (CT X-ray) offers a way to observe 'in vivo' some characteristics of a tested sample in the course of its deformation. Therefore we developed an X-ray transparent tri-axial cell that was included in a medical purpose X-ray scanner with a volumetric resolution of the order of 1 mm3. This technique is described and applied to a porous calcarenite, which is regularly scanned for porosity evolution during mechanical testing. The experiment is performed at low confining pressure (2-10 MPa). During testing, an axial load is applied until failure and is then progressively decreased. In these experiments, the peak stress is preceded by phase of diffuse dilatancy. After failure localization, the axial stress is unloaded until the stress reaches isotropy. During this unloading phase, the previous diffuse dilatancy is lost due to an elastic relaxation. Then, the stress is completely relaxed. At this moment the dilatancy increases again and the residual dilatancy is larger than that reached at the peak stress. When observed "post mortem" at microscopic scale, the dilatant structures are comprised of cataclastic deformation bands and cracks in some larger crystals.
International Journal of Rock Mechanics and Mining Science

hal-00767563
https://hal.archives-ouvertes.fr/hal-00767563
DOI : 10.1016/j.ijrmms.2012.07.020

Éditeur(s) : HAL CCSD
Résumé : Today, one of the main challenges in the oil industry is the exploitation of new resources in naturally fractured reservoirs often located in structurally complex areas such as plate boundaries, mountain ranges or near salt structures. While numerical models of rock deformation based on continuum mechanics are becoming industry standard in providing efficient means for modelling natural fractures in reservoirs, the knowledge of past perturbed stress fields, which is referred as the type (normal, wrench or reverse), orientation and magnitude of the regional or local tectonic stresses that needs to be applied as boundary condition in numerical simulations, is often unknown or approximated.The essence of this thesis is to improve the recovery of the paleostress field needed to constrain numerical simulations. I first described and discuss through a comprehensive mechanically-based multi-parametric study how far we can rely on the commonly used paleostress inversion methods based on fault slip data and the Wallace and Bott assumptions. I then compared this method with a new generation technique based on geomechanics using field observations. Since slip markers on faults are hardly observed in core or image log, I used observed natural fracture data as main drivers for the inversion of the paleostress using geomechanically-based method. I demonstrated, through various outcrop and subsurface examples, how this can efficiently be done. Finally, I aimed at addressing the problem of polyphase fracture data sets with unknown mechanical type (joints, faults, stylolites ...) and expanded the mechanical stress inversion to the separation of tectonic phases.
Aujourd'hui, l'un des principaux défis dans l'industrie pétrolière est l'exploitation de nouvelles ressources dans les réservoirs naturellement fracturés souvent situés dans des zones structurellement complexes tels que les frontières de plaques, les chaînes de montagnes ou les structures de proches des dômes de sel. Alors que les modèles numériques de déformation des roches basée sur la mécanique des milieux continus fournissant des moyens efficaces pour la modélisation de fractures naturelles dans les réservoirs, sont devenus la norme dans l'industrie, les paléo-contraintes régionales ou locales appliquées comme condition aux limites dans les simulations numériques, définies par le régime (normal, décrochant ou inverse), l'orientation, et la magnitude des contraintes tectoniques, sont souvent inconnues ou approximées.L'essence de cette thèse est d'améliorer la prédiction du champ de paléo-contrainte nécessaire pour contraindre les simulations numériques. J’ai décrit dans un premier temps à travers une étude comparative multi-paramétrique complète basée sur la mécanique, dans quelle mesure nous pouvions compter sur les méthodes d'inversion des paléo-contraintes basées sur les hypothèses de Wallace et Bott et les données de glissement sur les failles. J’ai ensuite comparé ces méthodes avec une technique d’inversion de nouvelle génération basée sur la géomécanique en utilisant les observations de terrain. Puisque les marqueurs de glissement sur les failles sont rarement observés le long du forage, j’ai utilisé l’inversion géomécanique des contraintes pour les données de fractures naturelles observées. J’ai alors démontré, l’efficacité de cette technique à travers divers exemples d'affleurements et de subsurface. Enfin, j’ai proposé une solution afin de résoudre le problème des données de fractures polyphasées à type cinématique inconnu (joints, failles, stylolites ...) et étendu l’inversion de contrainte basée sur la géomécanique à la séparation des phases tectoniques.
https://hal.archives-ouvertes.fr/tel-01324110

tel-01324110
https://hal.archives-ouvertes.fr/tel-01324110
https://hal.archives-ouvertes.fr/tel-01324110/document
https://hal.archives-ouvertes.fr/tel-01324110/file/theselejri.pdf

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Propagation energies for five examples of deformation bands in porous sandstones from four field sites in Nevada, Utah, and France were calculated by using the J-integral approach. Pure compaction bands that accommodate primarily closing displacements from the Valley of Fire (Nevada) site have a closing-mode band propagation energy of J I = 5.5 ± 1.6 kJ/m2. Shear-enhanced compaction bands having subequal amounts of normal (closing) and shear strains across them from the same site have propagation energies of J I = 6.11 ± 1.8 kJ/m2 and J II = 1.52 ± 0.5 kJ/m2 for closing and shearing modes respectively. Closing- and shearing-mode band propagation energies for shear-enhanced compaction bands from the Buckskin Gulch (Utah) site, 5.63 ± 1.7 and 1.91 ± 0.57 kJ/m2 and the Uchaux (France) site, 11.0 ± 3.3 and 2.35 ± 0.7 kJ/m2 respectively are comparable to the values for similar structures from the Valley of Fire site. Cataclastic deformation bands at the Orange (France) site accommodate significantly larger values of shear offset than do shear-enhanced compaction bands, with a ratio of shear to closing offset that exceeds 7. The calculated closing- and shearing-mode propagation energies for these shear bands, 17.8 ± 5.4 and 3.3 ± 1.0 kJ/m2 respectively are comparable to those for pure or shear-enhanced compaction bands deformed at approximately the same depth of burial. Strain softening of cataclastic compactional shear bands implies unstable shearing, whereas stable and perhaps strain-hardening shearing may be inferred for shear-enhanced compaction bands. Displacement-length scaling relations for shear-enhanced compaction bands of the form D∝L are consistent with the results and with suggestions of band thickening during growth obtained from bifurcation analyses and with field observations of shear zones in porous host rock.
ISSN: 0376-9429

hal-00750341
https://hal.archives-ouvertes.fr/hal-00750341
DOI : 10.1007/s10704-012-9730-2

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
The outstanding exposure of deformation bands in a multilayer sequence of the Orange quarry, Provence, France, motivates a study investigating the development and controls of deformation band geometries by field mapping combined with finite element modeling. Field mapping yields new insights into angular relations between, and evolution of, the deformation bands as well as provides input parameters for the setup and boundary conditions of the numerical simulations using ADELI 2D. In particular, reverse-sense deformation bands are found to have developed within three of the four exposed layers of the multilayer stack with similar orientations to bedding, indicating layer-parallel contraction. Numerical simulations, carried out as a parametric study to investigate the influence on deformation band development and geometry, successfully reproduce the sequential development of deformation bands in the three layers as seen in the field as well as recreate the observed angular geometries of similar to 39 degrees to the maximum compression. This angular relationship is put into context with observations from other field studies and theoretical values to explore controls of deformation band orientations. Furthermore, band localization is impeded in the model by increased layer cohesive strength, demonstrating the importance of host-rock property variations on where localization of bands within the multilayer sequence. Results from both field investigation and numerical simulations are consistent with regional tectonics, where the strata underwent gentle folding due to thrust faulting at depth, and bring further insight into the development and geometry of deformation bands in both extensional and contractional tectonic regimes.
ISSN: 0148-0227

hal-00639452
https://hal.archives-ouvertes.fr/hal-00639452
DOI : 10.1029/2011JB008365

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : Extensional fault systems in the Earth's crust can exhibit two end-member geometries that we identify as distributed and localized faulting regimes. A satellite image analysis of fault populations from the Main Ethiopian Rift-Afar area reveals that the rift architecture contains these two faulting regimes. The occurrence of these regimes reveals a jump in the scale of fault segmentation and linkage. Strain localization at rift border zones exhibits particularly large-scale fault linkage and a power law size distribution. This regime replaces prior distributed fault systems, showing small-scale fault linkage and an exponential size distribution. The distributed faulting is interpreted as confined to the thick trap basalt carapace. We show that continental fault systems can develop by a combination of these two geometries, and we demonstrate how to quantitatively decipher the jump between them.
ISSN: 0278-7407

hal-00411147
https://hal.archives-ouvertes.fr/hal-00411147
DOI : 10.1029/2007TC002148

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
3D seismic data located in the Gjallar Ridge (Vøring Basin, offshore Norway) reveals a closely-spaced polygonal fault system affecting more than 800 m of homogeneous mud-dominated Quaternary and Tertiary sequences. As some faults reach the modern seafloor, they represent an active polygonal fault system at present day. Even if the processes remain unclear and are still under debate, it is generally agreed that the initiation of polygonal faults is the result of shallow burial dewatering of fine-grained unconsolidated sediments by volumetric compaction. 3D seismic data are commonly interpreted by propagating horizons automatically and by picking faults manually. However, in the case of polygonal fault intervals, this approach is time consuming due to the huge number of faults and because automatic propagation can be misleading. In this study, we applied a new technique of 3D seismic interpretation based on a sequential stratigraphy analysis, using the new PaleoScan© software (Eliis Company). It allowed us to build a 3D geological model computing more than 300 horizons within the faulted intervals. We then used the coherency attribute, depicting anomalies in the shape of seismic waveform like faults, in order to constrain a possible link between fault distribution and stratigraphic levels. Our approach allows fault throws to be calculated in milliseconds on any polygonal fault plane. The result shows that fault segments have been reactivated by dip-linkage. Distribution of faults depends on mechanical units, intervals characterized by different petrophysical properties, which are independent from lithological and diagenetic changes. According to these results, we propose a model showing the evolution of polygonal fault intervals in which faulting stages are separated by a quiescence phase during burial. A first tier of polygonal faults is initiated at a specific depth, according to the Cam-clay model. Then, following a period of quiescence during which mud-rich sediments continued to accumulate, new fault segments are initiated above the first mechanical unit and within this undeformed interval. New nucleated faults then connect downward to pre-existing underlying polygonal fault system, thus progressively increasing the thickness of the faulted interval.
ISSN: 0025-3227

hal-00772470
https://hal.archives-ouvertes.fr/hal-00772470
DOI : 10.1016/j.margeo.2012.07.016

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
Nowadays, technological advances in satellite imagery measurements as well as the development of dense geodetic and seismologic networks allow for a detailed analysis of surface deformation associated with active fault seismic cycle. However, the study of earthquake dynamics faces several limiting factors related to the difficulty to access the deep source of earthquake and to integrate the characteristic time scales of deformation processes that extend from seconds to thousands of years. To overcome part of these limitations and better constrain the role and couplings between kinematic and mechanical parameters, we have developed a new experimental approach allowing for the simulation of strike-slip fault earthquakes and analyze in detail hundreds of successive seismic cycle. Model rheology is made of multilayered visco-elasto-plastic analog materials to account for the mechanical behavior of the upper and lower crust and to allow simulating brittle/ductile coupling, postseismic deformation phase and far-field stress transfers. The kinematic evolution of the model surface is monitored using an optical system, based on subpixel spectral correlation of high-resolution digital images. First, results show that the model succeed in reproducing the deformation mechanisms and surface kinematics associated to the main phases of the seismic cycle indicating that model scaling is satisfactory. These results are comforted by using numerical algorithms to study the strain and stress distribution at the surface and at depth, along the fault plane. Our analog modeling approach appears, then, as an efficient complementary approach to investigate earthquake dynamics.
ISSN: 0278-7407

hal-01174176
https://hal.archives-ouvertes.fr/hal-01174176
DOI : 10.1002/2014TC003701

Éditeur(s) : HAL CCSD Elsevier
Résumé : Displacement-length data from faults, joints, veins, igneous dikes, shear deformation bands, and compaction bands define two groups. The first group, having a power-law scaling relation with a slope of n = 1 and therefore a linear dependence of maximum displacement and discontinuity length (D-max = gamma L), comprises faults and shear (non-compactional or non-dilational) deformation bands. These shearing-mode structures, having shearing strains that predominate over volumetric strains across them, grow under conditions of constant driving stress, with the magnitude of near-tip stress on the same order as the rock's yield strength in shear. The second group, having a power-law scaling relation with a slope of n = 0.5 and therefore a dependence of maximum displacement on the square root of discontinuity length (D-max = alpha L-0.5), comprises joints, veins, igneous dikes, cataclastic deformation bands, and compaction bands. These opening- and closing-mode structures grow under conditions of constant fracture toughness, implying significant amplification of near-tip stress within a zone of small-scale yielding at the discontinuity tip. Volumetric changes accommodated by grain fragmentation, and thus control of propagation by the rock's fracture toughness, are associated with scaling of predominantly dilational and compactional structures with an exponent of n = 0.5.
ISSN: 0191-8141

hal-00411173
https://hal.archives-ouvertes.fr/hal-00411173
DOI : 10.1016/j.jsg.2008.08.001

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : This study describes normal fault zones formed in foreland arkosic turbidites (the Grès d'Annot Formation, SW French Alps) under deep diagenesis conditions (~200 °C) and highlights the occurrence of two markedly different fault-rock types: (1) the foliated fault rocks of the Moutière-Restefond area; and (2) the dilatant fault rocks of the Estrop area. The deformation of (1) is dominated by intra- and transgranular fracturing, pressure solution of quartz and feldspar grains and syn-kinematic phyllosilicate precipitation resulting from feldspar alteration. The combination of these mechanisms results in a strongly anisotropic strain with intense shortening normal to the foliation (pressure solution) and extension parallel to the foliation (quartz- and calcite-sealed extension veins). This deformation implies local mass transfer that may be achieved without (or with limited) volume change. The deformation of (2) is expressed as dilatant quartz-sealed veins and breccia textures in which the main mechanisms are transgranular fracturing and quartz precipitation. Type (2) implies fault volume increase, isotropy of deformation and mass transfer at distances larger than in type (1). This study discusses the origins of (1) and (2) and shows that the permeability of (1) is anisotropic, with higher values than the host rocks parallel to the Y main deformation axis (i.e. perpendicular to the slip vector), whereas the permeability of (2) is isotropic and equivalent to that of the host rocks.
ISSN: 0954-4879

hal-01115177
https://hal.archives-ouvertes.fr/hal-01115177
DOI : 10.1111/ter.12100

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The interplay between fault zone cataclasis and cementation is important since both processes can drastically reduce the permeability of faults in porous sandstones. Yet the prediction of fault cementation in high-porosity sandstone reservoirs remains elusive. Nevertheless, this process has rarely been investigated in shallowly buried faults (<2 km; T°<80 °C) where its sealing capacity could be acquired early in the geological history of a reservoir. In this paper, the macro- and microscopic analysis of a fault zone in the porous Cenomanian quartz arenite sands of Provence (France) shows that silica diagenesis occurs in the most intensely-deformed cataclastic parts of the fault zone. This fault zone shows 19–48% of its total thickness occupied by low-porosity quartz-cemented cataclastic shear bands whose porosities range from 0 – ca. 5%. The analysis of the weathering profile around the fault zone reveals the presence of groundwater silcretes in the form of tabular, tightly silicified concretions cross-cut by the fault. Detailed transmitted light, cold-cathodoluminescence and scanning electron microscopy analyses of the silica cements (from the fault and the silcrete) reveal that all the silica cements originate from groundwater diagenetic processes. This study therefore shows that silica cementation can occur specifically in fault zones and as groundwater silcrete in the shallow context of a groundwater system, generated at the vicinity of an erosional unconformity.
ISSN: 0191-8141

hal-01278286
https://hal.archives-ouvertes.fr/hal-01278286
DOI : 10.1016/j.jsg.2015.10.001

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Displacement-length data from dilatant fractures (joints, veins, igneous dikes) and several varieties of deformation bands were analyzed statistically to investigate the applicability of mechanical models proposed for their formation. All 17 datasets are generally consistent with equilibrium or long-term power-law slopes on the displacement-length diagram of either 1.0 or 0.5. Similar to many faults, disaggregation deformation bands are consistent with a power-law scaling relation having a slope of approximately c = 1, implying a linear dependence of maximum displacement and discontinuity length (Dmax = γL). In contrast, dilatant fractures, cataclastic deformation bands, and shear-enhanced compaction bands are consistent with a power-law scaling relation with a slope of approximately c = 0.5, implying a dependence of maximum displacement on the square root of length (Dmax = αL1/2). The scaling relations represent an average, or long-term equilibrium outcome of deformation for conditions such as length-scale, time-scale, temperature, chemistry, and an effectively homogeneous far-field stress field, allowing for variations such as rapid and/or localized behaviors. The displacement-length scaling of these geologic structures follows systematic relationships that provide information on host-rock properties and the physics of fracture and deformation-band propagation.
ISSN: 0191-8141

hal-00818130
https://hal.archives-ouvertes.fr/hal-00818130
DOI : 10.1016/j.jsg.2012.12.005

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wallace (1951) and Bott (1959) were the first to introduce the idea that the slip on each fault surface has the same direction and sense as the maximum shear stress resolved on that surface. However, this simplified hypothesis is questionable since fault mechanical interactions may induce slip reorientations. Earlier numerical geomechanical models confirmed that the slickenlines (slip vectors) are not necessarily parallel to the maximum resolved shear stress but are consistent with local stress perturbations. This leads us to ask as to what extent the Wallace and Bott simplifications are reliable as a basis hypothesis for stress inversion from fault slip data. Here, a geomechanical multi-parametric study using a 3D boundary element method, covering (i) fault geometries such as intersected faults or corrugated fault surfaces, (ii) the full range of Andersonian state of stress, (iii) fault friction, (iv) fault fluid pressure, (v) half space effect and (vi), rock properties, is performed in order to understand the effect of each parameter on the misfit angle between geomechanical slip vectors and the resolved shear stresses. It is shown that significant misfit angles can be found under specific configurations invalidating the Wallace and Bott assumptions, even though fault friction tends to minimize the misfit. We therefore conclude that in such cases, stress inversions based on fault slip data should be interpreted with care.
ISSN: 0040-1951

hal-01218418
https://hal.archives-ouvertes.fr/hal-01218418
DOI : 10.1016/j.tecto.2015.06.030

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Field observations of highly porous and permeable sandstone in the Orange area (S-E Basin, France) show that networks of shear-enhanced compaction bands can form in a contractional regime at burial depths of about 400 m ± 100 m. These bands show equal compaction and shear displacements, are organized in conjugate and densely distributed networks, and are restricted to the coarse-grained (mean grain diameter of 0.6 ± 0.1 mm) and less porous (porosity of 26 ± 2%) sand layers. The bands are crush microbreccia with limited grain comminution and high grain microfracture density. They show reductions of permeability (mD) ranging from 0 to little more than 1 order of magnitude. They show no control on the alteration products related to meteoric water flow, which suggests that these shear-enhanced compaction bands have no or only negligible influence on subsurface fluid flow. Their selective occurrence and small (20%) reduction in transmissibility in densely populated layers prevented them from compartmentalizing the sandstone reservoirs. A comparison with compaction-band populations in the Navajo and Aztec sandtsones (western U.S.) emphasizes the role of burial depth and the presence of chemical compaction processes for the sealing potential of deformation bands.
ISSN: 0191-8141

hal-00807309
https://hal.archives-ouvertes.fr/hal-00807309
DOI : 10.1016/j.jsg.2012.11.008