Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy P - Oxford Open Option A Oxford University Press (OUP)
Résumé : International audience
It is well known that sedimentary rocks having same porosity can have very different pore size distribution. The pore distribution determines many characteristics of the rock, among which its transport properties are often the most useful. Multifractal analysis is a powerful tool that is increasingly used to characterize the pore space. In this study, we performed multifractal analysis of pore distribution on simulated sedimentary rocks using the relaxed bidisperse ballistic deposition model (RBBDM). The RBBDM can generate a 3-D structure of sedimentary rocks of variable porosity by tuning the fraction p of particles of two different sizes. We also performed multifractal analysis on two samples of real sedimentary rock to compare with the simulation studies. One sample, an oolitic limestone is of high porosity (40 per cent) while the other is a reefal carbonate of low porosity, around 7 per cent. 2-D sections of X-ray microtomographs of the real rocks were stacked sequentially to reconstruct the real rock specimens. Both samples show multifractal character. The results from analysis of real rock agree quite well with the simulated structure of low porosity. The simulated rock of high porosity showed a weak multifractal nature though the real rock sample of similar porosity was found to be strongly multifractal. We propose a ‘structure parameter’ ξ which is a function of porosity and the generalized dimensions, and controls the transport properties of the rock.
ISSN: 0956-540X

hal-01174142
https://hal.archives-ouvertes.fr/hal-01174142
DOI : 10.1093/gji/ggu417

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A set of four reactive flow-through experiments at temperature T = 100 degrees C and total pressure P=12 MPa was performed in limestone reservoir samples. By using various ranging from 0.7 to 10 MPa, these experiments mimic mass transfers occurring (1) near the injection well, where the brine is almost saturated with CO2 (i.e. P-CO2 approximate to P), and (2) at increasing distances from the injection well, where the fluid displays lower values and higher divalent cation concentrations due rock dissolution along the fluid pathway. Results for P-CO2 = 10 MPa show non-uniform dissolution features associated with transport-controlled mass transfer, while reaction-controlled uniform dissolution is observed for P-CO2 = 2.5 MPa. The experiment with P-CO2 = 6 MPa allows investigating in detail the transition from transport-to reaction-controlled dissolution. Conversely, the experiment reproducing conditions far from the injection well (P-CO2 = 0.7 MPa), shows a decrease of porosity triggered by the precipitation of Mg-rich calcite. For all the dissolution experiments, the time-resolved porosity phi(t) can be modeled by a simple non-linear equation including parameters that characterise the dissolution regime triggered by the reactivity of the inlet fluid (measured by the Damkohler number, Da). Furthermore, all dissolution experiments display power scaling between permeability (k) and porosity (phi) with distinctly different scaling exponents characterising the reactivity of the fluid percolating the sample, independently from the decrease with time of the reactive surface area. It is shown also that dissolution at moderate positive values of Da seems the most efficient to increase permeability and promote a rapid spreading of the reaction front, while inducing minimal modification of the porosity in the vicinity of the CO2 injection well. These results can be used to parameterize the k-phi function for modeling the earliest dissolution processes occurring in the vicinity of the reaction front.
ISSN: 0009-2541

hal-00445277
https://hal.archives-ouvertes.fr/hal-00445277
DOI : 10.1016/j.chemgeo.2009.03.028

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Diffusion parameters for HTO, 36Cl−, and 125I− were determined on Upper Toarcian argillite samples from the Tournemire Underground Research Laboratory (Aveyron, France) using the through diffusion technique. The direction of diffusion was parallel to the bedding plane. The purpose of the present study was 3-fold; it was intended (i) to confirm the I− interaction with Upper Toarcian argillite and to verify the effects of initial I− concentration on this affinity, as previously observed by means of radial diffusion experiments, (ii) to highlight any discrepancy between Cl− and I− diffusivity, and (iii) to investigate the effect of an increase of the ionic strength of the solution on the anionic tracers' diffusive behaviour. The results show that the effective diffusion coefficient (De) and diffusion accessible porosity (εa) values obtained with an ionic strength (I.S.) synthetic pore water of 0.01 eq L−1 are: De = 2.35-2.50 × 10−11 m2 s−1 and εa = 12.0-15.0% for HTO, and De = 14.5-15.5 × 10−13 m2 s−1 and εa = 2.5-2.9% for 36Cl−. Because of anionic exclusion effects, anions diffuse slower and exhibit smaller diffusion accessible porosities than HTO, taken as a water tracer. The associated effective diffusion coefficient (De) and rock capacity factor (α) obtained for 125I are: De = 7.00-8.60 × 10−13 m2 s−1 and α = 4.3-7.2%. Such values make it possible to calculate low 125I distribution ratios (0.0057 < RD < 0.0192 mL g−1) which confirm the trend indicating that the 125I rock capacity factor increases with the decrease of the initial I− concentration. Additional through-diffusion experiments were carried out with a higher ionic strength synthetic pore water (I.S. = 0.11 eq L−1). No evolution of HTO diffusion parameters was observed. The anionic tracers' effective diffusion coefficient increased by a factor of two but no clear evolution of their accessible porosity was observed. Such a paradox could be related to the particularly small mean pore size of the Upper Toarcian argillite of Tournemire. The most significant finding of this study is the large discrepancy (factor of two) between the values of the effective diffusion coefficient for 125I and 36Cl. Whatever the ionic strength of the synthetic solution used, 125I exhibited De values two times lower than those of 36Cl. A detailed explanation for this difference cannot be given at present even if a hypothesis based on ion-pairing or on steric-exclusion cannot be excluded. This makes questionable the assumption usually made for quantifying 125I sorption and postulating that 36Cl and 125I would diffuse in the same porosity. In other terms, at Tournemire, 125I sorption could be more pronounced than previously indicated.
ISSN: 0883-2927

hal-00757749
https://hal.archives-ouvertes.fr/hal-00757749
DOI : 10.1016/j.apgeochem.2011.12.017

Éditeur(s) : HAL CCSD
Résumé : The coastal intrusion of brine threatens populations. This is particularly prejudicial in carbonate environments. We have studied the Miocene coral reef of S-E Majorca for better understanding the relation between geological structure and intrusion. For that purpose, we have used multi-scalar and multi-disciplinary methods. The measurements in 25 boreholes over the whole coral platform have allowed defining the stratigraphic structure and some elements of the regional tectonic. The reef progrades in the NE-SW direction, starting from the Aquitanian to terminates at the Messinian. The Messinian Salinity Crisis involves a disappearance of the Mediterranean corals and results in a Terminal Carbonate Complex which overlays a great part of the previously living corals of Majorca. At the experimental site scale, the study of the mineral composition, the texture, and the diagenesis have allowed characterization of the carbonate sequence heterogeneity. Layers of mineralization accompanied by dolomitization and low porosity correspond to postdepositional eustatic levels. The causes for the existence and the orientation of fractures are studied. The permeability to porosity relation is approached. The porosity structure is studied by comparison between primary and secondary porosity. This study contributes to the knowledge of the world best documented site for the evolution of carbonate reef reservoirs, with applications for brine intrusion and for hydrocarbon extraction.
Les intrusions d'eau salée en zone côtière constituent une menace pour la population. Celles-ci sont particulièrement dommageables en contexte carbonaté. Nous avons étudié le récif corallien Miocène du sud-est de Majorque afin de comprendre la relation entre structure géologique et intrusion. Pour cela nous avons utilisé des méthodes multi-scalaires et multi-disciplinaires. Les mesures dans 25 forages sur l'ensemble de la plateforme corallienne ont permis de préciser la structure stratigraphique et certains éléments de la tectonique régionale. Le récif prograde dans la direction NE-SO, en partant de l'Aquitanien pour aboutir au Messinien. La Crise de Salinité Messinienne entraîne une disparition des coraux méditerranéens et se traduit par un Complexe Carbonaté Terminal qui s'étend sur une grande partie des coraux autrefois vivants de Majorque. A l'échelle du site expérimental, l'étude de la composition minérale, de la texture et de la diagenèse ont permis de caractériser l'hétérogénéité de la séquence carbonatée. Des couches de minéralisation accompagnées de dolomitisation et de faible porosité correspondent à différents niveaux eustatiques post-dépositionnels. Les causes de l'existence et de l'orientation des fractures sont étudiées. La relation de perméabilité à porosité est précisée. La structure de porosité est étudiée par comparaison entre la porosité primaire et la porosité secondaire. Cette étude contribue à la connaissance du site le mieux documenté au monde pour l'évolution des réservoirs carbonatés récifaux, avec applications pour les intrusions d'eau salée et l'extraction des hydrocarbures.
https://tel.archives-ouvertes.fr/tel-00440019

tel-00440019
https://tel.archives-ouvertes.fr/tel-00440019
https://tel.archives-ouvertes.fr/tel-00440019/document
https://tel.archives-ouvertes.fr/tel-00440019/file/thesemariasube.pdf

Éditeur(s) : Université des Antilles. Service commun de la documentation
Extrait de : Les rencontres culturelles de la BU 2015-2016. Université des Antilles
Description : Performance "POROSITY #1" des artistes Annabel Guérédrat et Henri Tauliaut dans la cadre de la soirée consacrée à la présentation du numéro 21 de la revue Recherche en Esthétique consacrée à "La réception de l'art". A la suite de la performance, Dominique Berthet (professeur en esthétique, Université des Antilles), éditeur de la revue, présente la démarche du dernier numéro de la revue et anime la soirée.

Droits : CC-BY-NC-ND - Attribution - Pas d'utilisation commerciale - Pas de modification
Permalien : http://www.manioc.org/fichiers/V16132
V16132

Éditeur(s) : Elsevier
Résumé : A study of organic carbon mineralization from the Congo continental shelf to the abyssal plain through the Congo submarine channel and Angola Margin was undertaken using in situ measurements of sediment oxygen demand as a tracer of benthic carbon recycling. Two measurement techniques were coupled on a single autonomous platform: in situ benthic chambers and microelectrodes, which provided total and diffusive oxygen uptake as well as oxygen microdistributions in porewaters. In addition, sediment trap fluxes, sediment composition (Org-C, Tot-N, CaCO3, porosity) and radionuclide profiles provided measurements of, respectively input fluxes and burial rate of organic and inorganic compounds. The in situ results show that the oxygen consumption on this margin close to the Congo River is high with values of total oxygen uptake (TOU) of 4 +/- 0.6, 3.6 +/- 0.5 mmol m(-2) d(-1) at 1300 and 3100m depth, respectively, and between 1.9 +/- 0.3 and 2.4 +/- 0.2 mmol m(-2) d(-1) at 4000 m depth. Diffusive oxygen uptakes (DOU) were 2.8 +/- 1.1, 2.3 +/- 0.8, 0.8 +/- 0.3 and 1.2 +/- 0.1 mmol m(-2) d(-1), respectively at the same depths. The magnitude of the oxygen demands on the slope is correlated with water depth but is not correlated with the proximity of the submarine channel-levee system, which indicates that cross-slope transport processes are active over the entire margin. Comparison of the vertical flux of organic carbon with its mineralization and burial reveal that this lateral input is very important since the sum of recycling and burial in the sediments is 5-8 times larger than the vertical flux recorded in traps. Transfer of material from the Congo River occurs through turbidity currents channelled in the Congo valley, which are subsequently deposited in the Lobe zone in the Congo fan below 4800 m. Ship board measurements of oxygen profiles indicate large mineralization rates of organic carbon in this zone, which agrees with the high organic carbon content (3%) and the large sedimentation rate (19 mm y(-1)) found on this site. The Lobe region could receive as high as 19 mol C m(-2) y(-1), 1/3 being mineralized and 2/3 being buried and could constitute the largest depocenter of organic carbon in the South Atlantic.
Deep Sea Research Part II: Topical Studies in Oceanography (0967-0645) (Elsevier), 2009-11 , Vol. 56 , N. 23 , P. 2223-2238

Droits : 2009 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/2009/publication-7316.pdf
DOI:10.1016/j.dsr2.2009.04.005
http://archimer.ifremer.fr/doc/00000/7316/

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : Direct numerical simulations of flow through two millimeter-scale rock samples of limestone and sandstone are performed using three diverse fluid dynamic simulators. The resulting steady-state velocity fields are compared in terms of the associated empirical probability density functions (PDFs) and key statistics of the velocity fields. The pore space geometry of each sample is imaged at 5.06−μm voxel size resolution using X-ray microtomography. The samples offer contrasting characteristics in terms of total connected porosity (about 0.31 for the limestone and 0.07 for the sandstone) and are typical of several applications in hydrogeology and petroleum engineering. The three-dimensional fluid velocity fields within the explicit pore spaces are simulated using ANSYS® FLUENT® ANSYS Inc. (2009), EULAG Prusa et al. (Comput. Fluids 37, 1193–1207 2008), and SSTOKES Sarkar et al. (2002). These computational approaches are highly disperse in terms of algorithmic complexity, differ in terms of their governing equations, the adopted numerical methodologies, the enforcement of internal no-slip boundary conditions at the fluid-solid interface, and the computational mesh structure. As metrics of comparison to probe in a statistical sense the internal similarities/differences across sample populations of velocities obtained through the computational systems, we consider (i) integral quantities, such as the Darcy flux and (ii) main statistical moments of local velocity distributions including local correlations between velocity fields. Comparison of simulation results indicates that mutually consistent estimates of the state of flow are obtained in the analyzed samples of natural pore spaces despite the considerable differences associated with the three computational approaches. We note that in the higher porosity limestone sample, the structures of the velocity fields obtained using ANSYS FLUENT and EULAG are more alike than either compared against the results obtained using SSTOKES. In the low-porosity sample, the structures of the velocity fields obtained by EULAG and SSTOKES are more similar than either is to the fields obtained using ANSYS FLUENT. With respect to macroscopic quantities, ANSYS FLUENT and SSTOKES provide similar results in terms of the average vertical velocity for both of the complex microscale geometries considered, while EULAG tends to render the largest velocity values. The influence of the pore space structure on fluid velocity field characteristics is also discussed.
ISSN: 1420-0597

hal-01174152
https://hal.archives-ouvertes.fr/hal-01174152
DOI : 10.1007/s10596-015-9486-7

Éditeur(s) : HAL CCSD
Résumé : International audience
The porosity (from values of <1% up to more than 50%, with a mean value of 36.5%) and permeability (from very low values to 20.4 D, with a mean value around 800 mD) of 38 plugs, with a diameter 40 mm, have been measured. These plugs were taken approximately every 1.5 m along a 100 m-long core, sampling a series of reefal carbonate platform lithofacies. A non-unique relationship between porosity and permeability is obtained. In addition, the porosity was measured from processing X-ray micro-tomography images with resolutions ranging from 0.42 to 190.0 µm and sampling volumes ranging from less than 1 µm3 to few cm3. Depending on the structure of the pore network, the computed porosity is, in some cases, controlled by the X-ray image resolution and the sampled volume. While high resolution is required to image micro-porous material, large samples with lower resolution images are necessary for identifying distributed vugs and millimetre-scale structures. This study shows that multi-resolution X-ray micro-tomography is an effective tool for characterizing the multi-scale pore structure of carbonate rocks and understanding how it may control key petrophysical parameters such as porosity and permeability.
Geological Society Special Publication

hal-01174157
https://hal.archives-ouvertes.fr/hal-01174157
DOI : 10.1144/SP406.12

Éditeur(s) : HAL CCSD Integrated Ocean Drilling Program
Résumé : In this report we present the results of laboratory measurements carried out to explore the electrical properties of gabbroic and troctolitic samples from Integrated Ocean Drilling Program (IODP) Hole U1309D in the Atlantis Massif, an oceanic core complex located at 30°N on the Mid-Atlantic Ridge. Oceanic core complexes are presumably localized in portions of heterogeneous oceanic crust that are relatively rich in igneous rocks and are the locus of significant hydrothermal activity. Electrical properties of igneous rocks are used to discuss the rocks' porosity structure as a function of mineralogy, alteration processes, and deformation. Electrical properties of the gabbroic suites sampled during IODP Expedition 304/305 can contribute to the understanding of these processes in the Atlantis Massif. We present the full suite of electrical data together with density and porosity measurements on the same suite of samples.
ISSN: 1930-1014

hal-00464179
https://hal.archives-ouvertes.fr/hal-00464179
DOI : 10.2204/iodp.proc.304305.204.2009

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
A set of synthetic aggregates, containing mixtures of calcite and muscovite, were compacted with varying uniaxial loads ranging from 20 MPa up to 400 MPa. Their elastic properties have been measured using compressional and shear waves in confining hydrostatic pressures up to 475 MPa. Measured seismic velocities are shown to depend on 1) the ratio of calcite to muscovite, 2) the uniaxial load used during sample manufacturing, and 3) the porosity amount prior to velocity measurements. The matrix framework may also affect the seismic velocities, but this effect is not easily quantifiable. In general, measured seismic velocities decrease with increasing muscovite content and porosity. Elastic properties have been calculated based on texture measurements, which were obtained by neutron diffraction. The calculated velocities are based on the calcite and muscovite single crystal elastic tensors, their orientation distribution functions, and their modal fractions. A large discrepancy is apparent between calculated and measured velocities, where the former always overestimate the actual velocities. Shear waves display less of a difference between calculated and measured values, than do compressional waves, indicating that waves propagating by shearing are less affected by sample porosity and matrix framework. A better agreement between measured and calculated seismic velocities arises when the initial porosity is taken into account, using a differential effective medium model. Seismic anisotropy is evident from both measured and calculated velocities, and is low for samples containing pure calcite, but becomes prominent as the muscovite concentration increases. The intensity of anisotropy further depends on the uniaxial load used during sample compaction and the initial porosity.
ISSN: 0148-0227

hal-00512666
https://hal.archives-ouvertes.fr/hal-00512666
DOI : 10.1029/2009JB006523

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
The brittle to ductile transition (BDT) in rocks may strongly influence their transport properties (i.e., permeability, porosity topology ...) and the maximum depth and temperature where hydrothermal fluids may circulate. To examine this transition in the context of Icelandic crust, we conducted deformation experiments on a glassy basalt (GB) and a glass-free basalt (GFB) under oceanic crust conditions. Mechanical and micro-structural observations at a constant strain rate of 10(-5) s(-1) and at confining pressure of 100-300 MPa indicate that the rocks are brittle and dilatant up to 700-800 degrees C. At higher temperatures and effective pressures the deformation mode becomes macroscopically ductile, i.e., deformation is distributed throughout the sample and no localized shear rupture plane develops. The presence of glass is a key component reducing the sample strength and lowering the pressure of the BDT. In the brittle field, strength is consistent with a Mohr-Coulomb failure criterion with an internal coefficient of friction of 0.42 for both samples. In the ductile field, strength is strain rate-and temperature-dependent and both samples were characterized by the same stress exponent in the range 3 < n < 4.2 but by very different activation energy Q(GB) = 59 +/- 15 KJ/mol and Q(GFB) = 456 +/- 4 KJ/mol. Extrapolation of these results to the Iceland oceanic crust conditions predicts a BDT at similar to 100 degrees C for a glassy basalt, whereas the BDT might occur in non-glassy basalts at deeper conditions, i.e., temperatures higher than 550 +/- 100 degrees C, in agreement with the Icelandic seismogenic zone.
ISSN: 0148-0227

hal-00760905
https://hal.archives-ouvertes.fr/hal-00760905
DOI : 10.1029/2011JB008884

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The interplay between fault zone cataclasis and cementation is important since both processes can drastically reduce the permeability of faults in porous sandstones. Yet the prediction of fault cementation in high-porosity sandstone reservoirs remains elusive. Nevertheless, this process has rarely been investigated in shallowly buried faults (<2 km; T°<80 °C) where its sealing capacity could be acquired early in the geological history of a reservoir. In this paper, the macro- and microscopic analysis of a fault zone in the porous Cenomanian quartz arenite sands of Provence (France) shows that silica diagenesis occurs in the most intensely-deformed cataclastic parts of the fault zone. This fault zone shows 19–48% of its total thickness occupied by low-porosity quartz-cemented cataclastic shear bands whose porosities range from 0 – ca. 5%. The analysis of the weathering profile around the fault zone reveals the presence of groundwater silcretes in the form of tabular, tightly silicified concretions cross-cut by the fault. Detailed transmitted light, cold-cathodoluminescence and scanning electron microscopy analyses of the silica cements (from the fault and the silcrete) reveal that all the silica cements originate from groundwater diagenetic processes. This study therefore shows that silica cementation can occur specifically in fault zones and as groundwater silcrete in the shallow context of a groundwater system, generated at the vicinity of an erosional unconformity.
ISSN: 0191-8141

hal-01278286
https://hal.archives-ouvertes.fr/hal-01278286
DOI : 10.1016/j.jsg.2015.10.001

Éditeur(s) : European Geosciences Union (EGU)
Résumé : Barrier layers are defined as the layer between the pycnocline and the thermocline when the latter are different as a result of salinity stratification. We present a revisited 2-degree resolution global climatology of monthly mean oceanic Barrier Layer (BL) thickness first proposed by de Boyer Montegut et al. (2007). In addition to using an extended data set, we present a modified computation method that addresses the observed porosity of BLs. We name porosity the fact that barrier layers distribution can, in some areas, be very uneven regarding the space and time scales that are considered. This implies an intermittent alteration of air-sea exchanges by the BL. Therefore, it may have important consequences for the climatic impact of BLs. Differences between the two computation methods are small for robust BLs that are formed by large-scale processes. However, the former approach can significantly underestimate the thickness of short and/or localized barrier layers. This is especially the case for barrier layers formed by mesoscale mechanisms (under the intertropical convergence zone for example and along western boundary currents) and equatorward of the sea surface salinity subtropical maxima. Complete characterisation of regional BL dynamics therefore requires a description of the robustness of BL distribution to assess the overall impact of BLs on the process of heat exchange between the ocean interior and the atmosphere.
Ocean Science (1812-0784) (European Geosciences Union (EGU)), 2009-09 , Vol. 5 , N. 3 , P. 379-387

Droits : European Geosciences Union (EGU)
http://archimer.ifremer.fr/doc/2009/publication-6915.pdf
http://archimer.ifremer.fr/doc/2009/sup-6915.pdf
http://archimer.ifremer.fr/doc/00000/6915/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
ODP (Ocean Drilling Program)/IODP (Integrated Ocean Drilling Program) Site 1256 is located on the Cocos Plate in the Eastern Equatorial Pacific Ocean, in a 15 Ma old oceanic lithosphere formed at the EPR during a period of superfast spreading (>200 mm/yr). ODP/IODP Hole 1256D reached for the first time the contact between sheeted dikes and underlying gabbros. It consequently offers a unique opportunity to study in situ, in present-day oceanic crust, the root zone of the sheeted dike complex. This root zone is a thin, 100 m thick boundary layer between the magmatic system (i.e., the axial melt lens, similar to 1100 degrees C), and the overlying high temperature hydrothermal system (<= 450 degrees C). The understanding of interactions within this boundary layer is critical to that of crustal processes along mid-ocean ridges.;This work focuses on the petrophysical characterization of the root zone of the sheeted dike complex in order to further constrain the hydrothermal circulation system in the vicinity of the axial melt lens, as recorded in non-granoblastic dikes, granoblastic dikes, and varitextured gabbros. The petrophysical properties were determined from sample measurements in the laboratory and were compared to in situ downhole geophysical probing. The porosity structure is bipolar, depending on lithology, resulting in a layered system. Non-granoblastic dikes are generally altered in the greenschist fades (similar to>250 degrees C) with relatively high and interconnected (cementation index m similar to 1.72, electrical tortuosity tau similar to 28.3) porosity (1.5%). In contrast, gabbros are retrogressively metamorphosed in the amphibolite (similar to>450 degrees C) and greenschist facies, with lower porosity (1.3%) that involves numerous fissures and cracks, resulting in a more connected medium (m similar to 1.58, tau similar to 11.8) than non-granoblastic dikes. These cracks are more abundant but also tend to close with increasing depth as indicated in downhole geophysical data. Porosity and alteration, as viewed from surface electrical conductivity, appear to be directly correlated.
ISSN: 0040-1951

hal-00544556
https://hal.archives-ouvertes.fr/hal-00544556
DOI : 10.1016/j.tecto.2010.07.013

Éditeur(s) : HAL CCSD
Résumé : This thesis has been conducted on a fractured crystalline basement located in Ploemeur (South of Brittany, France). The detailed study of this basement requires a good understanding of their internal structures, namely their intrinsic properties, flow mode, density and fractures distribution. This work is focused on the petrophysical characterization of the granitic formations. Physical properties were determined from downhole geophysical measurements and images, and petrophysical measurements with thin sections made for each mini-core in the laboratory. Fresh-altered schist and fresh-altered granite separated by a normal angle fault are the main lithology of the Ploemeur crystalline basement. The results showed that the petrophysical properties were function of both porosity variation and degree of alteration and that the pore-space topology was found to be porositydependent. This thesis introduces a new formula between electrical resistivity and porosity. In addition, the laboratory measurements of Ploemeur revealed that seismic wave velocity was a function not only of porosity, but also of the predominant pore type. In general, the pore aspect ratio inverted from velocity measurements were classified roughly into crack shape. In the Ploemeur crystalline basement, the downhole geophysical measurements and images were used to measure changes in physical and chemical properties in the borehole fluid and the bedrock surrounding the boreholes. The effective integration of different geophysical methods, hydrogeological tests and lithological description was the best way to characterize the fractures in the crystalline basement, and is critical for a suitable estimation of fluid circulation.
Le socle cristallin fracturé, situé à Ploemeur (Bretagne sud, France) est l'objet de ce travail de thèse. L'étude détaillée du socle nécessite une bonne compréhension de la structure interne, à savoir les propriétés intrinsèques, le mode d'écoulement, la densité et la distribution des fractures. Ce travail de thèse est consacré à la caractérisation pétrophysique des formations granitiques. Les propriétés physiques ont été déterminées à partir de l'interprétation des données de mesures de géophysique en forage, des images de paroi du puits et des mesures pétrophysiques réalisées sur carottes en laboratoire. Afin de replacer les mesures dans leur contexte lithologique, une lame mince a été analysée pour chaque mini-carotte. Les formations lithologiques rencontrées dans le socle cristallin de Ploemeur sont des schistes et granites sains et altérés, ces deux lithologies étant séparées par une zone de faille. Les résultats ont montré que les propriétés pétrophysiques des roches étaient fonction à la fois de la variation de la porosité et du degré d'altération des roches et que la topologie de l'espace poreux était fortement dépendante de la porosité. Cette thèse introduit une nouvelle formule entre la résistivité électrique et la porosité. De plus, les mesures en laboratoire sur les échantillons de Ploemeur révèlent que les vitesses sismiques ne sont pas seulement fonction de la quantité de porosité, mais aussi fonction de facteur de forme. Ce dernier a été calculé sur les échantillons du socle de Ploemeur à partir des vitesses acoustiques. Les résultats ont montré que la porosité est de forme fissurale. L'intégration des données issues des images optiques et acoustiques, des mesures de géophysique en forage, et de la description des carottes a permis d'étudier de façon détaillée la géologie et l'hydrodynamique du socle de Ploemeur. L'intégration effective de ces différentes méthodes avec les tests hydrogéologiques ressort comme la meilleure façon de caractériser les fractures et les circulations en eau dans le socle.
https://tel.archives-ouvertes.fr/tel-00444175

Droits : info:eu-repo/semantics/OpenAccess
tel-00444175
https://tel.archives-ouvertes.fr/tel-00444175
https://tel.archives-ouvertes.fr/tel-00444175/document
https://tel.archives-ouvertes.fr/tel-00444175/file/thesebelghoul.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Carbonation of peridotite is a widespread process in nature, with emerging societal and environmental implications through geological storage of CO2. We studied the micro- and nano-scale structures associated with the carbonation of peridotite pervaded by a CO2-rich water and the induced changes of its hydrodynamic properties. Focused ion beam (FIB) nanotomography was coupled with scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations. An experimental sample of dunite core percolated by a CO2-rich fluid (pCO2 = 11 MPa) at 160 °C was compared with a naturally carbonated sample from the Atlantic Ridge (Exp. IODP 304). Results of the 8-days percolation experiment show continuous alteration of olivine into magnesite locally associated with a poorly crystalline serpentine-type mineral referred to as proto-serpentine. The experiment is also characterized by an overall decrease in rock porosity (from 7.7 to 6.4%) and permeability (from 8.5 × 10− 16 to 1.7 × 10− 16 m2). The primary inter-granular porosity (1 to 10 μm) is progressively filled with magnesite, leading to the overall decrease of permeability. At the same time, a secondary small-scale porosity (10 nm to 1 μm) is created at the tip of the dissolution features along the (010) cleavage planes of olivine grains. Carbonate crystals grow within these etch-pit structures behind the dissolution front. Dissolution and precipitation occur at a relative rate that maintains the secondary porosity over the timescale of the experiment (i.e. carbonate growth has to be the slowest one). This process is interpreted as an interface coupled dissolution-precipitation mechanism of olivine carbonation. Proto-serpentine is only formed in highly reduced flow areas, such as small olivine etch-pits (10 to 500 nm wide), which are more isolated from CO2 input. SEM-FIB analyses show the 3D preferential orientation of the dissolution-precipitation planes within a given olivine grain. It suggests the formation of lateral connections between the etch-pits (infra-micrometric “channels”) providing access to reactants and removing reaction products at the reaction sites. The experimental results show that olivine dissolution and magnesite precipitation converge to a quasi-steady state resulting in a constant carbonation rate controlled by reaction kinetics and not by mass transfer for this flow regime. The system self-regulates, independently of the porosity change at least during this incipient stage of olivine carbonation. Similar textures are observed in natural samples collected at 170 m-depth in the vicinity of veinlets driving late fluids down into the cooling oceanic lithosphere. This suggests that similar mechanisms are active in nature and can play an important role in the late, low temperature alteration stages of fractured peridotite. These results also highlight the critical role of nm-scale spatial arrangement of dissolution and precipitation features on mass transfers and on the sustainability of olivine carbonation through coupled dissolution-precipitation processes.
ISSN: 0009-2541

hal-01684733
https://hal.archives-ouvertes.fr/hal-01684733
DOI : 10.1016/j.chemgeo.2017.11.013

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Melt generation in the continental crust is thought to significantly influence seismic bulk velocities and anisotropy, although existing laboratory data provide limited constraints on such seismic attributes. In this study we measured ultrasonic compressional wave speeds (Vp) and anisotropy during sample compaction, mica-breakdown and melt-generation in synthetic, foliated quartz–muscovite aggregates. Measurements were performed at peak conditions of 300 MPa hydrostatic confining pressure and 750 °C, over a six hour time period, for three separate samples where wave propagation directions were aligned at 0°, 45° and 90° with respect to the foliation plane. The experiments are initially marked by sample compaction and rapid reduction in porosity (from 25% to <2 vol%), with a corresponding increase in Vp. During initial stages of the experiment Vp ranges from 4.65 to 5.45 km/s, depending on the direction of the P wave propagation, resulting in up to ∼16% anisotropy, which originates mainly from the preferred orientation of muscovite and possible incipient melt lenses oriented parallel to foliation. As the experiment progresses the bulk Vp decreases gradually and Vp anisotropy drops from ∼16% to ∼2% after five hours into the experiment. The drop in anisotropy is caused by muscovite-breakdown and increasing amount of partial melting of the aggregate. The bulk velocities are considerably lower than predicted for a mixture of muscovite and β-quartz (stable at 300 MPa and 750 °C). Thermodynamic modeling indicates that mica breakdown and production of melt with ∼2 wt% dissolved water in the aggregate can explain the low Vp, even though β-quartz is stable; the modeled Vp is ∼4.75 km/s at 300 MPa and 750 °C. These ultrasonic attributes signify movement of the melt to fill vacant pores and coating grain boundaries, effectively connecting melt films and reducing seismic anisotropy. The results may apply to regions where crustal melting is on-going, in particular regions of elevated temperature that are only weakly deforming, with coupled anomalously low bulk velocities and seismic anisotropy.
ISSN: 0012-821X

hal-01243569
https://hal.archives-ouvertes.fr/hal-01243569
DOI : 10.1016/j.epsl.2015.05.039

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
We describe the structure, microstructure, and petrophysical properties of fault rocks from two normal fault zones formed in low-porosity turbiditic arkosic sandstones, in deep diagenesis conditions similar to those of deeply buried reservoirs. These fault rocks are characterized by a foliated fabric and quartz-calcite sealed veins, which formation resulted from the combination of the (1) pressure solution of quartz, (2) intense fracturing sealed by quartz and calcite cements, and (3) neoformation of synkinematic white micas derived from the alteration of feldspars and chlorite. Fluid inclusion microthermometry in quartz and calcite cements demonstrates fault activity at temperatures of 195degC to 268degC. Permeability measurements on plugs oriented parallel with the principal axes of the finite strain ellipsoid show that the Y axis (parallel with the foliation and veins) is the direction of highest permeability in the foliated sandstone (10-2 md for Y against 10-3 md for X, Z, and the protolith, measured at a confining pressure of 20 bars). Microstructural observations document the localization of the preferential fluid path between the phyllosilicate particles forming the foliation. Hence, the direction of highest permeability in these fault rocks would be parallel with the fault and subhorizontal, that is, perpendicular to the slickenlines representing the local slip direction on the fault surface. We suggest that a similar relationship between kinematic markers and fault rock permeability anisotropy may be found in other fault zone types (reverse or strike-slip) affecting feldspar-rich lithologies in deep diagenesis conditions.
ISSN: 0149-1423

hal-00903428
https://hal.archives-ouvertes.fr/hal-00903428
DOI : 10.1306/03071312127

Résumé : Pour beaucoup de cultures, un sol non travaillé est une alternative de plus en plus crédible au travail intensif du sol, en particulier pour des raisons environnementales. Mais l’ananas (ananas comosus) présente un enracinement fragile très sensible à la structure, ce qui motive souvent un travail important du sol avant plantation. L’alternative d’une plantation sans travail du sol ne va donc pas de soi. L’objet de cette thèse est de répondre à la question de la faisabilité d’une culture d’ananas sans travail du sol, en remplaçant ce dernier par une plante de service « décompactante » dont les traits racinaires seraient favorables à la (re)structuration d’un sol compact. Le travail de cette thèse a donc porté sur l’évaluation de plusieurs espèces candidates, puis sur l’étude, au champ, des effets sur le sol de la plus prometteuse (Stylosanthes guianensis ). Enfin, dans le cadre d’un essai au champ comparant un système de culture innovant ananas sans travail du sol, on a étudié l’effet de la plante de service sur le fonctionnement de la culture de l’ananas. Dans un premier essai, c’est le Stylosanthes guianensis qui, comparé à huit autres espèces (Arachis pintoï, Brachiaria decumbens, Cajanus cajan, Crotalaria juncea, Cynodon dactylon, Eleusine coracana, Pueraria phaseoloides, et le maïs), a montré les traits racinaires les plus favorables à la structuration d’un sol compact. Les valeurs supérieures du diamètre racinaire moyen et de la densité de longueur racinaire (DRL) caractérisent les principaux traits impliqués. Dans un deuxième essai, les mesures de conductivité hydraulique, d’indice des vides du sol et d’analyse d’images de blocs de sol imprégné sur la répartition surfacique des différents types de porosité ont montré que la culture du Stylosanthes guianensis avait augmenté l’indice des vides du sol et provoqué l’apparition d’une porosité fissurale de grande taille, contribuant ainsi à l’amélioration de la structure du sol. Enfin, un troisième essai mettant en comparaison (i) un système de culture innovant où la culture d’ananas est implantée sans travail du sol après une culture de S. guianensis restructurante et (ii) un système conventionnel comportant un travail profond du sol (et pas de plante de service) a montré que le rendement en fruit est similaire dans les deux systèmes. Cet essai a permis de vérifier que l’enracinement de l’ananas en condition de sol non travaillé bénéficiait du précédent S. guianensis.
For many crops, direct drilling is a well-tried alternative facing the damaging effects of intensive tillage, mainly for environmental causes. But, pineapple (ananas comosus), presents a fragile rooting system which is very sensitive to soil structure. This leads frequently to intensive soil tillage before planting. Direct drilling is not so evident. The aim of this thesis is to give an answer to the feasibility of a no till system for pineapple cultivation, by using a plant with favorable roots traits for compacted soil (re)structuration. This work consisted in evaluating several candidate species, followed by the study, on the field, of the effects the most promising on soil (Stylosanthes guianensis). Finally, through a field experiment, comparing an innovating no till pineapple cultivation system we studied the use effects of Stylosanthes guianensis on the pineapple crop functioning. In a first experiment, Stylosanthes guianensis compared with eight other species (Arachis pintoï, Brachiaria decumbens, Cajanus cajan, Crotalaria juncea, Cynodon dactylon, Eleusine coracana, Pueraria phaseoloides and corn) showed better roots traits for structuring a compacted soil. Measures of average root diameter and root length density are the main implicated roots traits. In a second experiment, the measures of hydraulic conductivity, of the soil void ratio and the analysis of blocks of resin-impregnated soil on the surface distribution of the different type of porosity, all of this showed that Stylosanthes guianensis had increased the soil void ratio and had caused the creation of large-sized cracked porosity, thus contributing to the improvement of the soil structure. Finally, a third experiment involving a comparison between (i) an innovating cultivation system where pineapple is growing in a no till soil after a structuring crop of S. guianensis and (ii) a conventional system with deep tillage (without structuring crop), showed similar fruit yield. This experiment showed evidence that the rooting of pineapple in no till soil benefited from the previous Stylosanthes.

http://www.theses.fr/2014AGUY0725/document

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Porous thin films considered for applications like separation, sensing and microelectronic have to sustain mechanical stresses during their integration process or in working conditions. Thanks to recent progress in processing methods, it is now possible to precisely control the porosity and combine ordered mesopores with randomly-distributed macropores to achieve hierarchically porous materials. The mechanical properties of thin films containing different types of porosity (ordered meso, random macro and hierarchical) have been investigated by means of nanoindentation. In particular a method recently proposed by Li and Vlassak (H. Li, J.J. Vlassak, Journal of Materials Research 24 (2009) 1114-1126) is applied to account for the substrate effect. Residual indent impressions were imaged by Atomic Force Microscopy (AFM) to provide some insights in the mechanical behavior of the films. In addition, experimental indentation moduli are compared to theoretical predictions obtained via Finite Element (FE) analysis. The different porous structures have been modeled by FE to obtain the effective elastic properties from which the indentation modulus can be inferred. Finally, the experimental-model differences are discussed. © 2010 Elsevier Inc. All rights reserved.
ISSN: 1387-1811

hal-01683194
https://hal.univ-antilles.fr/hal-01683194
DOI : 10.1016/j.micromeso.2010.09.004