Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : A differential effective medium (DEM) model is used to predict elastic properties for a set of porous and anisotropic aggregates, comprised of mixtures of calcite and muscovite. The DEM takes into consideration an anisotropic background medium with triclinic or higher symmetry, in which inclusions of idealized ellipsoidal shape are added incrementally. In general, the calculated elastic properties of a solid that contains inclusions representing "dry" pores/cracks are strongly dependent on the orientation and aspect ratio of the inclusions. Aspect ratios of inclusions in the synthetic aggregates, which consist of air-filled pores, are estimated from anisotropy of magnetic susceptibility (AMS) of samples whose pore space has been impregnated with a colloidal ferrofluid. The AMS derived pore shape geometry is used as an input value for inclusions in the DEM. Modeling results are compared with laboratory determined elastic properties, measured with ultrasonic waves. Calculated shear wave velocities agree in general well with laboratory measured S wave velocities, whereas calculated P wave velocities are typically 0.5-1.1 km/s higher than measured values. Differences between calculated and measured P wave velocities are attributed mainly to incomplete and biased ferrofluid saturation of pores. Spherical pores are preferably filled during imbibition, in comparison to thin cracks, which leads to overprediction of the calculated P wave velocities. The amount of ferrofluid that fills the pore space is dependent on the ratio of calcite to muscovite and the load used for compaction during sample synthesis. The permeability decreases with increasing muscovite content and increasing compaction load. Incomplete saturation of samples with high-muscovite content is confirmed by X-ray microtomography density contrast imaging of dry and ferrofluid saturated specimens.
ISSN: 0148-0227

hal-00617717
https://hal.archives-ouvertes.fr/hal-00617717
DOI : 10.1029/2010JB007750

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Progress in seismic methodology and ambitious large-scale seismic projects are enabling high-resolution imaging of the continental crust. The ability to constrain interpretations of crustal seismic data is based on laboratory measurements on rock samples and calculations of seismic properties. Seismic velocity calculations and their directional dependence are based on the rock microfabric, which consists of mineral aggregate properties including crystallographic preferred orientation (CPO), grain shape and distribution, grain boundary distribution, and misorientation within grains. Single-mineral elastic constants and density are crucial for predicting seismic velocities, preferably at conditions that span the crust. However, high-temperature and high-pressure elastic constant data are not as common as those determined at standard temperature and pressure (STP; atmospheric conditions). Continental crust has a very diverse mineral composition; however, a select number of minerals appear to dominate seismic properties because of their high-volume fraction contribution. Calculations of microfabric-based seismic properties and anisotropy are performed with averaging methods that in their simplest form takes into account the CPO and modal mineral composition, and corresponding single crystal elastic constants. More complex methods can take into account other microstructural characteristics, including the grain shape and distribution of mineral grains and cracks and pores. Dynamic or active wave propagation schemes have recently been developed, which offer a complementary method to existing static averaging methods generally based on the use of the Christoffel equation. A challenge for the geophysics and rock physics communities is the separation of intrinsic factors affecting seismic anisotropy, due to properties of crystals within a rock and apparent sources due to extrinsic factors like cracks, fractures, and alteration. This is of particular importance when trying to deduce crustal composition and the state of deformation from seismic parameters.
ISSN: 8755-1209

Droits : info:eu-repo/semantics/OpenAccess
hal-01685568
https://hal.archives-ouvertes.fr/hal-01685568
https://hal.archives-ouvertes.fr/hal-01685568/document
https://hal.archives-ouvertes.fr/hal-01685568/file/Almqvist_et_al-2017-Reviewssur Geophysics.pdf
DOI : 10.1002/2016RG000552

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
A set of synthetic aggregates, containing mixtures of calcite and muscovite, were compacted with varying uniaxial loads ranging from 20 MPa up to 400 MPa. Their elastic properties have been measured using compressional and shear waves in confining hydrostatic pressures up to 475 MPa. Measured seismic velocities are shown to depend on 1) the ratio of calcite to muscovite, 2) the uniaxial load used during sample manufacturing, and 3) the porosity amount prior to velocity measurements. The matrix framework may also affect the seismic velocities, but this effect is not easily quantifiable. In general, measured seismic velocities decrease with increasing muscovite content and porosity. Elastic properties have been calculated based on texture measurements, which were obtained by neutron diffraction. The calculated velocities are based on the calcite and muscovite single crystal elastic tensors, their orientation distribution functions, and their modal fractions. A large discrepancy is apparent between calculated and measured velocities, where the former always overestimate the actual velocities. Shear waves display less of a difference between calculated and measured values, than do compressional waves, indicating that waves propagating by shearing are less affected by sample porosity and matrix framework. A better agreement between measured and calculated seismic velocities arises when the initial porosity is taken into account, using a differential effective medium model. Seismic anisotropy is evident from both measured and calculated velocities, and is low for samples containing pure calcite, but becomes prominent as the muscovite concentration increases. The intensity of anisotropy further depends on the uniaxial load used during sample compaction and the initial porosity.
ISSN: 0148-0227

hal-00512666
https://hal.archives-ouvertes.fr/hal-00512666
DOI : 10.1029/2009JB006523

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Melt generation in the continental crust is thought to significantly influence seismic bulk velocities and anisotropy, although existing laboratory data provide limited constraints on such seismic attributes. In this study we measured ultrasonic compressional wave speeds (Vp) and anisotropy during sample compaction, mica-breakdown and melt-generation in synthetic, foliated quartz–muscovite aggregates. Measurements were performed at peak conditions of 300 MPa hydrostatic confining pressure and 750 °C, over a six hour time period, for three separate samples where wave propagation directions were aligned at 0°, 45° and 90° with respect to the foliation plane. The experiments are initially marked by sample compaction and rapid reduction in porosity (from 25% to <2 vol%), with a corresponding increase in Vp. During initial stages of the experiment Vp ranges from 4.65 to 5.45 km/s, depending on the direction of the P wave propagation, resulting in up to ∼16% anisotropy, which originates mainly from the preferred orientation of muscovite and possible incipient melt lenses oriented parallel to foliation. As the experiment progresses the bulk Vp decreases gradually and Vp anisotropy drops from ∼16% to ∼2% after five hours into the experiment. The drop in anisotropy is caused by muscovite-breakdown and increasing amount of partial melting of the aggregate. The bulk velocities are considerably lower than predicted for a mixture of muscovite and β-quartz (stable at 300 MPa and 750 °C). Thermodynamic modeling indicates that mica breakdown and production of melt with ∼2 wt% dissolved water in the aggregate can explain the low Vp, even though β-quartz is stable; the modeled Vp is ∼4.75 km/s at 300 MPa and 750 °C. These ultrasonic attributes signify movement of the melt to fill vacant pores and coating grain boundaries, effectively connecting melt films and reducing seismic anisotropy. The results may apply to regions where crustal melting is on-going, in particular regions of elevated temperature that are only weakly deforming, with coupled anomalously low bulk velocities and seismic anisotropy.
ISSN: 0012-821X

hal-01243569
https://hal.archives-ouvertes.fr/hal-01243569
DOI : 10.1016/j.epsl.2015.05.039