Éditeur(s) : HAL CCSD Integrated Ocean Drilling Program
Résumé : In this report we present the results of laboratory measurements carried out to explore the electrical properties of gabbroic and troctolitic samples from Integrated Ocean Drilling Program (IODP) Hole U1309D in the Atlantis Massif, an oceanic core complex located at 30°N on the Mid-Atlantic Ridge. Oceanic core complexes are presumably localized in portions of heterogeneous oceanic crust that are relatively rich in igneous rocks and are the locus of significant hydrothermal activity. Electrical properties of igneous rocks are used to discuss the rocks' porosity structure as a function of mineralogy, alteration processes, and deformation. Electrical properties of the gabbroic suites sampled during IODP Expedition 304/305 can contribute to the understanding of these processes in the Atlantis Massif. We present the full suite of electrical data together with density and porosity measurements on the same suite of samples.
ISSN: 1930-1014

hal-00464179
https://hal.archives-ouvertes.fr/hal-00464179
DOI : 10.2204/iodp.proc.304305.204.2009

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The complex electrical impedance of a garnet-biotite-sillimanite residual enclave in the Neogene dacite of El Hoyazo (SE Spain) has been determined up to 978 °C at 200-300 MPa. This well studied material represents a direct sampling of the Alborán Domain thinned lower crust undergoing partial melting. The paragenesis is garnet + biotite + sillimanite + plagioclase + graphite ± cordierite coexisting with widespread (~ 10 wt.%) rhyolitic melt occurring as inclusions and interstitial glass and developed during regional anatexis at 850 ± 50 °C and 500-700 MPa. The samples were used in cyclic measurements consisting in heating-cooling ramps at progressively higher maximum temperature to observe the effect of reactions on conductivity. In the first cycle up to 850 °C at 2-3 kbar, re-melting of the interstitial glass is achieved with no additional reactions and logarithmic conductivity (S/m) is up to − 1.5. At T > 950 °C new melt with orthopyroxene + ilmenite is produced from biotite partial breakdown and the logarithmic conductivity (S/m) is up to − 0.7. Application of mixing models as Hashin-Shtrikman bounds or Archie's Law, shows that once interconnected, melt controls the electrical conductivity of the enclave. The electrical conductivity of the rock can be simulated with the electrical conductivity data obtained on the starting Matrix glass of the enclave and with the new melt. Our experimental results obtained on a graphitic metasedimentary material evidence show that graphite does not contribute to the conductivity enhancement and that the electrical anomaly observed below the Betics can be explained as effect of partial melting of a residual crust. Comparison with previous works on mafic granulites shows that similar conductivity values can be achieved both by melting of a residual felsic crust or by melting of mafic materials and suggests that pelitic rocks can be more common at deep levels than expected.
ISSN: 0040-1951

hal-00823063
https://hal.archives-ouvertes.fr/hal-00823063
DOI : 10.1016/j.tecto.2012.11.003

Éditeur(s) : HAL CCSD
Résumé : Ocean Drilling Program Hole 1256D reached for the first time the transition zone between the sheeted dike complex and the uppermost gabbros. The recovered crustal section offers a unique opportunity to study the deepest part of the hydrothermal system in present-day oceanic crust. We present a structural analysis of electrical borehole wall images. We identified, and measured the orientations of four categories of structures: major faults, minor fractures, possibly hydrothermal veins, and dikes. All structures tend to strike parallel to the paleo-ridge axis. Three major fault zones (meter thick) and dikes are steeply dipping (~ 75° on average) outward the ridge. Centimeter-thick moderately conductive planar features are interpreted as hydrothermal veins, are organized in arrays of consistent spacing, thickness, and orientation, and are dipping about 15-20° toward the ridge. This structural pattern is interpreted as an on-axis paleohydrothermal circulation system, with vertical, dike-parallel fractures, and sub-horizontal high-temperature hydrothermal veins at the base of the sheeted dike, which was subsequently rotated ~ 15° westward around a ridge-parallel, sub-horizontal axis. This rotation can be caused by upper-crustal block rotation along a listric normal fault, and/or subsidence at the ridge axis.
Ofioliti

hal-00757592
https://hal.archives-ouvertes.fr/hal-00757592
DOI : 10.4454/ofioliti.v37i1.402

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
During the early years of the Iceland Deep Drilling Project (IDDP), development of three distinctive technological and scientific approaches were formalised and then carried out until 2010 within a European funded project called HiTI (high temperature instruments for supercritical geothermal reservoir characterisation and exploitation). These approaches were: (1) development of several downhole instruments allowing them to function up to 300 ◦C and 400 ◦C, (2) identification of two new Na/Li cation ratio geothermometric relationships valid at very high temperature, (3) tracer testing with high temperature tolerant organic isomers and finally and (4) basalt rock deformation and petrophysical properties laboratory investigations at high temperature and pressure conditions.
ISSN: 0375-6505

hal-00921127
https://hal-brgm.archives-ouvertes.fr/hal-00921127
DOI : 10.1016/j.geothermics.2013.07.008

Éditeur(s) : HAL CCSD
Résumé : Geothermal energy is considered as a green and infinite energy source at human scale. Currently, the yield of geothermal power plants is limited to temperatures of the operating fluid which 350 °C. From tectonic and volcanic activity at mid-ocean ridges, Iceland is a location where supercritical fluid extraction (T> 375 °C) can considered for the near future. Exploiting such fluids could theoretically multiply by a factor of ten the electrical power delivered by geothermal wells. Can such fluids circulate at the base of brittle oceanic crust? This work investigates the petrophysical properties of basalts in order to constrain geophysical observations in Iceland and predict the behavior of very high temperature geo-hydrothermal reservoirs. The first approach consisted in studying the physical properties of rocks that have hosted deep hydrothermal circulations at oceanic ridges. The study of these rocks at ODP Site 1256 shows that the porosity measured both in the field and in the lab is associated with amphibolite facies alteration minerals (T> 500 ° C). The second approach was to recreate in the laboratory the conditions of pressure, temperature and pore fluid pressure of high temperature to supercritical hydrothermal systems to predict the mechanical and electrical properties of basalts under these conditions. The mechanical results indicate that the brittle/ductile transition occurs at a temperature of about 550° C, where a strong permeability decrease is expected. The implementation and calibration of a new cell for measuring electrical conductivity at high temperature provide the first results for the interpretation of geophysical data. When applied to basaltic crustal conditions in Iceland, these results indicate that hydrothermal fluids could circulate, at least temporarily, in a supercritical state up to 5 km depth.
La géothermie est considérée comme une source d'énergie propre et inépuisable à échelle humaine. Actuellement, le rendement des centrales géothermiques est limité à l'exploitation de fluides de températures inférieures à 350 °C. L'association de l'activité tectonique et volcanique aux dorsales océaniques fait de l'Islande un lieu où l'extraction de fluides supercritiques (T> 375 °C) peut être envisagée. Cette exploitation pourrait multiplier par dix la puissance électrique délivrée par le système géothermal. Ces fluides peuvent-ils circuler dans la croûte océanique ? Ce travail propose de contraindre les observations géophysiques et de prédire le fonctionnement des réservoirs géo-hydrothermaux de très haute température par l'étude des propriétés physiques des basaltes. La première approche est focalisée sur l'étude de roches ayant accueilli une circulation hydrothermale par le passé. L'étude de ces roches au site ODP 1256, montre que leur porosité est associée à la présence de minéraux d'altération hydrothermale du facies amphibolite (T> 500 °C). La seconde approche a consisté à recréer, en laboratoire, les conditions des systèmes hydrothermaux, à très haute température, afin de prédire les propriétés mécaniques et électriques des basaltes dans ces conditions. Les résultats mécaniques indiquent que la transition fragile/ductile, souvent associée à une forte décroissance de perméabilité, intervient à une température d'environ 550 °C. La mise en place d'une cellule de mesure de la conductivité électrique de haute température a fourni les premiers résultats utiles à l'analyse des données géophysiques. Appliqués aux conditions de la croûte basaltique Islandaise, ces résultats indiquent que des fluides hydrothermaux pourraient circuler au moins transitoirement à l'état supercritique jusqu'à ~ 5 km de profondeur.
https://tel.archives-ouvertes.fr/tel-00591798

tel-00591798
https://tel.archives-ouvertes.fr/tel-00591798
https://tel.archives-ouvertes.fr/tel-00591798/document
https://tel.archives-ouvertes.fr/tel-00591798/file/THESE_MV_pro.pdf

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
The brittle to ductile transition (BDT) in rocks may strongly influence their transport properties (i.e., permeability, porosity topology ...) and the maximum depth and temperature where hydrothermal fluids may circulate. To examine this transition in the context of Icelandic crust, we conducted deformation experiments on a glassy basalt (GB) and a glass-free basalt (GFB) under oceanic crust conditions. Mechanical and micro-structural observations at a constant strain rate of 10(-5) s(-1) and at confining pressure of 100-300 MPa indicate that the rocks are brittle and dilatant up to 700-800 degrees C. At higher temperatures and effective pressures the deformation mode becomes macroscopically ductile, i.e., deformation is distributed throughout the sample and no localized shear rupture plane develops. The presence of glass is a key component reducing the sample strength and lowering the pressure of the BDT. In the brittle field, strength is consistent with a Mohr-Coulomb failure criterion with an internal coefficient of friction of 0.42 for both samples. In the ductile field, strength is strain rate-and temperature-dependent and both samples were characterized by the same stress exponent in the range 3 < n < 4.2 but by very different activation energy Q(GB) = 59 +/- 15 KJ/mol and Q(GFB) = 456 +/- 4 KJ/mol. Extrapolation of these results to the Iceland oceanic crust conditions predicts a BDT at similar to 100 degrees C for a glassy basalt, whereas the BDT might occur in non-glassy basalts at deeper conditions, i.e., temperatures higher than 550 +/- 100 degrees C, in agreement with the Icelandic seismogenic zone.
ISSN: 0148-0227

hal-00760905
https://hal.archives-ouvertes.fr/hal-00760905
DOI : 10.1029/2011JB008884

Éditeur(s) : HAL CCSD Paris : E. Belin
Résumé : Un pour cent de l'énergie thermique contenue dans la croûte terrestre assurerait les besoins énergétiques de l'humanité pendant 100 000 ans ! Pour récupérer cette énergie aujourd'hui sous-exploitée, on fore dans des conditions toujours plus extrêmes.
ISSN: 0153-4092

hal-00564830
https://hal.archives-ouvertes.fr/hal-00564830

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
ODP (Ocean Drilling Program)/IODP (Integrated Ocean Drilling Program) Site 1256 is located on the Cocos Plate in the Eastern Equatorial Pacific Ocean, in a 15 Ma old oceanic lithosphere formed at the EPR during a period of superfast spreading (>200 mm/yr). ODP/IODP Hole 1256D reached for the first time the contact between sheeted dikes and underlying gabbros. It consequently offers a unique opportunity to study in situ, in present-day oceanic crust, the root zone of the sheeted dike complex. This root zone is a thin, 100 m thick boundary layer between the magmatic system (i.e., the axial melt lens, similar to 1100 degrees C), and the overlying high temperature hydrothermal system (<= 450 degrees C). The understanding of interactions within this boundary layer is critical to that of crustal processes along mid-ocean ridges.;This work focuses on the petrophysical characterization of the root zone of the sheeted dike complex in order to further constrain the hydrothermal circulation system in the vicinity of the axial melt lens, as recorded in non-granoblastic dikes, granoblastic dikes, and varitextured gabbros. The petrophysical properties were determined from sample measurements in the laboratory and were compared to in situ downhole geophysical probing. The porosity structure is bipolar, depending on lithology, resulting in a layered system. Non-granoblastic dikes are generally altered in the greenschist fades (similar to>250 degrees C) with relatively high and interconnected (cementation index m similar to 1.72, electrical tortuosity tau similar to 28.3) porosity (1.5%). In contrast, gabbros are retrogressively metamorphosed in the amphibolite (similar to>450 degrees C) and greenschist facies, with lower porosity (1.3%) that involves numerous fissures and cracks, resulting in a more connected medium (m similar to 1.58, tau similar to 11.8) than non-granoblastic dikes. These cracks are more abundant but also tend to close with increasing depth as indicated in downhole geophysical data. Porosity and alteration, as viewed from surface electrical conductivity, appear to be directly correlated.
ISSN: 0040-1951

hal-00544556
https://hal.archives-ouvertes.fr/hal-00544556
DOI : 10.1016/j.tecto.2010.07.013

Éditeur(s) : HAL CCSD Geological Society of America
Résumé : International audience
Fluid-rock interactions can control earthquake nucleation and the evolution of earthquake sequences. Experimental studies of fault frictional properties in the presence of fluid can provide unique insights into these interactions. We report the first results from experiments performed on cohesive silicate-bearing rocks (microgabbro) in the presence of pressurized pore fluids (H2O, drained conditions) at realistic seismic deformation conditions. The experimental data are compared with those recently obtained from carbonate-bearing rocks (Carrara marble). Contrary to theoretical arguments, and consistent with the interpretation of some field observations, we show that frictional melting of a microgabbro develops in the presence of water. In microgabbro, the initial weakening mechanism (flash melting of the asperities) is delayed in the presence of water; conversely, in calcite marble the weakening mechanism (brittle failure of the asperities) is favored. This opposite behavior highlights the importance of host-rock composition in controlling dynamic (frictional) weakening in the presence of water: cohesive carbonate-bearing rocks are more prone to slip in the presence of water, whereas the presence of water might delay or inhibit the rupture nucleation and propagation in cohesive silicate-bearing rocks.
ISSN: 0091-7613

hal-01054327
https://hal.archives-ouvertes.fr/hal-01054327
DOI : 10.1130/G34916.1

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
We performed 31 friction experiments on glassy basalts (GB) and glass-free basalts (GFB) at slip rates up to 6.5 m s−1 and normal stress up to 40 MPa (seismic conditions). Frictional weakening was associated to bulk frictional melting and lubrication. The weakening distance (Dw) was about 3 times shorter in GB than in GFB, but the steady state friction was systematically higher in GB than in GFB. The shorter Dw in GB may be explained by the thermal softening occurring at the glass transition temperature (Tg ~500°C), which is lower than the bulk melting temperature (Tm ~1250°C) of GFB. Postexperiment microanalyses suggest that the larger crystal fraction measured in GB melts results in the higher steady state friction value compared to the GFB melts. The effect of interstitial glass is to facilitate frictional instability and rupture propagation in GB with respect to GFB.
ISSN: 0094-8276

hal-01054139
https://hal.archives-ouvertes.fr/hal-01054139
DOI : 10.1002/2013GL058601

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Electrical resistivity soundings are used by geophysicists to determine the structure and composition of the Earth's crust and mantle and to explore natural resources (ore, oil, gas, water). Their interpretations in terms of composition and in-situ physical conditions depend mainly on laboratory measurements of electrical conductivity of rocks at simulated crustal conditions of temperature, pressure, saturation and pore pressures. These measurements present a numbers of limitations, in particular, in the case where conductive pore fluids are present, as in the case of deep reservoir conditions, where temperature exceeds 250 A degrees C. Here, we present a new cell capable of measuring electrical conductivity of large saturated samples at confining pressure up to 200 MPa, pore pressure up to 50 MPa, and temperature up to 500 A degrees C. The measurement cell has been developed in a commercial, internally heated, gas pressure apparatus (Paterson press). It is based on the concept of "guard ring" electrode, which is adapted to samples that are jacketed by a very conductive, metallic material. Numerical modeling of the current flow in the electrical cell allowed defining the optimal cell geometry. Calibration tests have been performed on Fontainebleau sandstones saturated with electrolytes of different conductivities, up to 350 A degrees C. The resulting electrical formation factor and temperature dependence of electrical conductivity are in very good agreement with previous studies. This new cell will improve the exploration and exploitation of deep fluid reservoirs, as in unconventional, high enthalpy geothermal fields. In particular, the investigations address possible effects of fluid-rock interactions on electrical resistivity of a reservoir host rock.
ISSN: 0169-3913

hal-00681997
https://hal.archives-ouvertes.fr/hal-00681997
DOI : 10.1007/s11242-011-9846-2

Éditeur(s) : HAL CCSD American Geophysical Union (AGU) American Geophysical Union
Résumé : International audience
The brittle to ductile transition may strongly influence hydraulic properties of rocks at the depth and temperature ranges that hydrothermal fluids circulate. To examine this transition in the context of the oceanic crust, we conducted a series of deformation experiments on a natural basalt sample at in situ oceanic crust conditions. Dilatancy was measured during deformation. The method consisted in monitoring the volume of pore fluid that flows into or out of the sample at constant pore pressure. Mechanical and microstructural observations at experimental constant strain rate of 10−5 s−1 indicated that the basalt was brittle and dilatant up to 800°C. At higher temperature, the deformation mode became macroscopically ductile and samples compacted. These observations have important implications on heat transfer and fluid migration in oceanic crust.
ISSN: 0094-8276

hal-01172352
https://hal.archives-ouvertes.fr/hal-01172352
DOI : 10.1002/2015GL063437