Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Propagation energies for five examples of deformation bands in porous sandstones from four field sites in Nevada, Utah, and France were calculated by using the J-integral approach. Pure compaction bands that accommodate primarily closing displacements from the Valley of Fire (Nevada) site have a closing-mode band propagation energy of J I = 5.5 ± 1.6 kJ/m2. Shear-enhanced compaction bands having subequal amounts of normal (closing) and shear strains across them from the same site have propagation energies of J I = 6.11 ± 1.8 kJ/m2 and J II = 1.52 ± 0.5 kJ/m2 for closing and shearing modes respectively. Closing- and shearing-mode band propagation energies for shear-enhanced compaction bands from the Buckskin Gulch (Utah) site, 5.63 ± 1.7 and 1.91 ± 0.57 kJ/m2 and the Uchaux (France) site, 11.0 ± 3.3 and 2.35 ± 0.7 kJ/m2 respectively are comparable to the values for similar structures from the Valley of Fire site. Cataclastic deformation bands at the Orange (France) site accommodate significantly larger values of shear offset than do shear-enhanced compaction bands, with a ratio of shear to closing offset that exceeds 7. The calculated closing- and shearing-mode propagation energies for these shear bands, 17.8 ± 5.4 and 3.3 ± 1.0 kJ/m2 respectively are comparable to those for pure or shear-enhanced compaction bands deformed at approximately the same depth of burial. Strain softening of cataclastic compactional shear bands implies unstable shearing, whereas stable and perhaps strain-hardening shearing may be inferred for shear-enhanced compaction bands. Displacement-length scaling relations for shear-enhanced compaction bands of the form D∝L are consistent with the results and with suggestions of band thickening during growth obtained from bifurcation analyses and with field observations of shear zones in porous host rock.
ISSN: 0376-9429

hal-00750341
https://hal.archives-ouvertes.fr/hal-00750341
DOI : 10.1007/s10704-012-9730-2

Éditeur(s) : HAL CCSD
Résumé : This study is designed to improve the understanding of structural, mechanical and petrophysical characteristics of deformation bands in porous sandstone such as their potential influence on fluid storage or migration in reservoir setting. Structural and petrophysical analysis of band networks from Provence show that permeability of band is mainly controlled by the degree of cataclasis and diagenetic processes at depth. Map-scale analysis of band networks underlines the major influence of tectonic regime on band distribution, organization and permeability. Band associated to normal-fault regime (cataclasis and low-permeability) are located around map-sclae-fault whereas band associated to thurst-fault regime (moderate cataclasis and permeability) are pervasively distributed in all the area. Reverse-sense band are cataclastic and low-permeabiilty around the Roquemaure thrust, which show the potential role of large-scale fault on structural and petrophysical characteristics of bands. This analysis also shows the influence of fault propagation on formation of low permeability catacastic bands. This analysis suggests also granulometry as factor controlling organization of band networks.A mechanical analysis of deformation bands is realized based on results from Provence. Yield envelopes of these materials are calculated from analytical solution. Triaxial tests done on sandstone (L'Etang quarry, Orange) confirm the shape of yield envelope theoretically calculated. Triaxial tests done on the poorly-lithified sands (Boncavaï quarry, Uchaux) show grain size, sorting and packing influencing yield envelope and cataclastic band localization at shallow burial depth. Stress paths are calculated for burial and tectonic event (extension and contraction) using the relationship between main stress and secondary stresses (K0) calibrated from well data. These different results are integrated into a model which allows to estimate type and structural characteristics of bands susceptible to form for a known geological setting.A structural, mechanical and petrophysical model is established form these results. This model is calibrated by permeability data from deformation bands of Provence and results from the mechanical model of strain localization. This model is also confronted to a synthesis of permeability data from literature, which confirms the influence of the different controlling parameters integrated to the model. This model is applied for two sites of uranium exploration/exploitation in porous sandstone reservoirs and validated by field observations.
Cette étude est destinée à améliorer la compréhension des caractéristiques structurales, pétrophysiques et mécaniques des bandes de déformation dans les grès poreux ainsi que de leur rôle potentiel sur la migration ou le piégeage des fluides en milieu réservoir. L'analyse structurale et pétrophysique des réseaux de bandes de Provence montre que leur perméabilité découle principalement de l'intensité de la cataclase dans leur microstructure et des processus diagénétiques qui peuvent s'y localiser avec la profondeur. L'analyse régionale de ces réseaux de bandes souligne l'influence majeure du régime tectonique sur leur distribution, leur organisation et leur perméabilité. Les bandes associées au régime normal (cataclactiques et peu perméables) sont localisées autour des failles cartographiques, tandis que les bandes associées au régime inverse (modérement cataclastiques et perméables) sont distribuées dans toute la région. Les bandes inverses sont fortement cataclastiques et imperméables uniquement autour du chevauchement de Roquemaure ce qui montre le rôle potentiel de la présence de grande faille sur les caractéristiques structurales et pétrophysiques de ces bandes. D'autre part, cette analyse suggère que la granulométrie de l'encaissant peut influencer l'initiation et l'organisation des réseaux. L'analyse mécanique des bandes de déformation a ensuite été réalisée à partir des résultats obtenus en Provence. L'enveloppe de plasticité de ces matériaux est calculée à l'aide d'une solution analytique. Les essais triaxiaux menés sur le grès de la carrière de l'Etang (orange) confirment la forme de ces enveloppes estimées théoriquement. Les essais réalisés sur les sables de Boncavaï (Uchaux) montrent que la taille des grains, le tri et de la compaction dans ces matériaux peu lithifiés influent sur leurs enveloppes de plasticité et la localisation des bandes cataclastiques à faibles profondeurs. Les trajets de contraintes sont estimés pour les phases d'enfouissement et de chargement tectonique (extension et compression) à partir de la relation entre contrainte principale et contraintes secondaires (K0), calibrée à partir de données de forage. Ces résultats sont intégrés à un modèle permettant d'estimer la nature et les caractéristiques structurales des bandes susceptibles de se former dans un contexte géologique donné. Un modèle structural, mécanique et pétrophysique a été établir à partir de ces différents résultats. Ce modèle est calibré à partir des données de perméabilité mesurées sur les bandes de Provence et des résultats du modèle mécanique de localisation cité précédemment. Ce modèle a ensuite été confronté à une synthèse des données de perméabilité disponibles dans la littérature et confirme l'influence des différents paramètres de contrôle pris en compte dans le modèle. Ce modèle a enfin pu être appliqué sur deux sites d'explorations/exploitations d'uranium en réservoir gréseux poreux et validé par les résultats obtenus, en concordance avec les observations de terrain.
https://tel.archives-ouvertes.fr/tel-01001389

NNT : 2013MON20067
tel-01001389
https://tel.archives-ouvertes.fr/tel-01001389
https://tel.archives-ouvertes.fr/tel-01001389/document
https://tel.archives-ouvertes.fr/tel-01001389/file/36072_BALLAS_2013_archivage-1_cor.pdf

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
The outstanding exposure of deformation bands in a multilayer sequence of the Orange quarry, Provence, France, motivates a study investigating the development and controls of deformation band geometries by field mapping combined with finite element modeling. Field mapping yields new insights into angular relations between, and evolution of, the deformation bands as well as provides input parameters for the setup and boundary conditions of the numerical simulations using ADELI 2D. In particular, reverse-sense deformation bands are found to have developed within three of the four exposed layers of the multilayer stack with similar orientations to bedding, indicating layer-parallel contraction. Numerical simulations, carried out as a parametric study to investigate the influence on deformation band development and geometry, successfully reproduce the sequential development of deformation bands in the three layers as seen in the field as well as recreate the observed angular geometries of similar to 39 degrees to the maximum compression. This angular relationship is put into context with observations from other field studies and theoretical values to explore controls of deformation band orientations. Furthermore, band localization is impeded in the model by increased layer cohesive strength, demonstrating the importance of host-rock property variations on where localization of bands within the multilayer sequence. Results from both field investigation and numerical simulations are consistent with regional tectonics, where the strata underwent gentle folding due to thrust faulting at depth, and bring further insight into the development and geometry of deformation bands in both extensional and contractional tectonic regimes.
ISSN: 0148-0227

hal-00639452
https://hal.archives-ouvertes.fr/hal-00639452
DOI : 10.1029/2011JB008365

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
From outcrops located in Provence (South-East France), we describe the distribution, the microstructures, and the petrophysical properties of deformation band networks related to both contractional and extensional tectonic events. In contraction, pervasively distributed networks of reverse-sense compactional shear bands are observed in all folded sand units of the foreland, whereas localized networks of clustered reverse-sense shear bands are only observed close to a large-scale thrust. In extensional setting, networks of clustered normal-sense shear bands are generally observed adjacent to map-scale faults (100 m–10 km scale), although some randomly distributed bands are also observed between these faults. Normal-sense cataclastic faults, i.e. zone of deformation bands containing a localized slip-surface, are also observed to be restricted to sand units, suggesting that faults initiated in the sands during extension, but not during contraction. Shear bands and faults show cataclastic microstructures with high-permeability reduction whereas compactional shear bands show crush microbreccia or protocataclastic microstructures with moderate permeability reduction. This basin-scale analysis underlines the major role of tectonic settings (thrust-fault versus normal-fault andersonian-stress regime) and the influence of inherited large-scale faults on the formation/localization of low-permeability shear bands. We also provide a geometrical analysis of the band network properties (spacing, thickness, shear/compaction ratio, degree of cataclasis, petrophysical properties) with respect to the median grain size, porosity and grain sorting of host sand. This analysis suggests that grain size, although less important than stress-state conditions and the presence of large-scale faults, has a non-negligible effect on band network geometry. No correlations are observed between the grain sorting, porosity and band network geometry.
ISSN: 0264-8172

hal-01116421
https://hal.archives-ouvertes.fr/hal-01116421
DOI : 10.1016/j.marpetgeo.2013.12.020

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Networks of localized conjugate compactive shear bands with large dihedral angles (corresponding to so-called shear-enhanced compaction bands) were generated in 3-layer plane strain finite-difference models. The central layer has elastic–plastic properties with a small positive internal friction coefficient, negative dilatancy factor, and the hardening modulus reducing during the deformation. The two other layers are elastic. The spatial organization of the networks in the central layer, resulting from the elastic–plastic instability of the 3-layer system, was shown to be dependent on the contrast of the elastic stiffness of the layers and on the friction between them. When the stiffness E of the elastic layers and/or the friction are small, the networks are rather symmetric (the bands of both orientation families are distributed homogeneously within the layer). An increase in E at high friction, results in the clustering of the bands of one orientation along a layer segment which is followed by another segment filled with the bands of the other orientation. Different network types are characterized by different band spacing which is smaller in the clustered networks. The intensity of inelastic deformation and hence of porosity reduction within the bands are also smaller in this case. The obtained band networks are very similar to those in nature where the same variability of the network organization is observed. Available geological and mechanical data confirm the conclusions from the modeling about the origin of this variability.
ISSN: 0040-1951

hal-01116201
https://hal.archives-ouvertes.fr/hal-01116201
DOI : 10.1016/j.tecto.2014.01.021

Éditeur(s) : HAL CCSD
Résumé : International audience
Mylonite bodies are exhumed extensions at depth of shallow structural level brittle faults. They are characterised by intense strain localisation involving large volumes of middle to lower continental crust. The analysis of shear zone geometry and microstructures is a useful tool to decipher deformation kinematics, though finite strain estimation is still relatively qualitative. Timing of the deformation has also been the focus of numerous studies using the complete spectrum of geochronometers. However, only rare examples provide geochronological data that can be unambiguously interpreted and cooling, recrystallisation and neocrystallisation are difficult to tell from each other. Thus, time-scales over which major mylonite zones develop and remain active under ductile conditions as well as their strain rate often remain poorly documented. We investigated two sections across the South-Armorican Shear Zone (SASZ), a crustal-scale pluri-km thick dextral shear zone active during a single tectonic event of late-Variscan age and associated with syntectonic granite emplacement.. Finite strain profiles on these cross-sections, quantified from average Quartz grain-size in 34 samples, show a strong deformation partitioning towards the center of the SASZ, with a decrease, for each section, from 150µm in slightly deformed zones to less than 7-5 µm in the core of the ultramylonite. Furthermore, toward the core of the SASZ, development of a penetrative shear band network progressively eliminates lenses of less deformed rocks and results in homogenisation of the Quartz grain sizes. In parallel, we performed in-situ UV-laser Ar/Ar dating on the fabric-forming white micas. White micas population can be decomposed into inherited muscovites carried by the folation and newly-formed, syn-tectonic substituted phengites located along the shear bands yielding 2 age groups for each sample. Along the profiles, the difference between these two ages evolves from 10-15 Ma in weakly deformed domains to zero toward the SASZ core. In addition, mylonite-forming phengites yielded the same age irrespectively of their position on the section or of the rock strain.. On the regional point of view, this study brings deformation-ages for the late-orogenic evolution of the South Armorican domain. Strain accumulated along the SASZ in a time-span extending to 300-298 Ma, i.e. contemporaneously with the activity of nearby major extensional shear zones. These results support a new model of crustal-scale shear zone activity, where the whole body of the shear zone is active throughout its history (defined as the largest age difference through the section), i.e. the actively deforming zone does not get progressively narrower. The strain distribution nevertheless evolves with time, with an increasingly large fraction partitioned in the ultramylonitic core.
EGU General Assembly
Vienne, Austria

insu-00839320
https://hal-insu.archives-ouvertes.fr/insu-00839320
BIBCODE : 2010EGUGA..12.9881A

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Fractures or discontinuities perpendicular to the least stress σ3 were generated in a synthetic rock analogue (granular, frictional, cohesive, and dilatant) material in axisymmetric extension tests. These fractures are of two types defined by the mean stress σ. When σ is very small, the fractures form through the mode I cracking at tensile σ3 equal to the material tensile strength. The fracture walls have smooth surfaces. At higher σ, these surfaces become rougher, with the topography features forming faint or delicate plumose patterns. The amplitude of the plumose topography increases with σ. The axial stress σ3 at fracturing reduces in magnitude and changes in sign with the σ increase. Thus σ3 orthogonal discontinuities can form at compressive σ3. SEM observations show that these discontinuities are deformation localization bands where the material is characterized by the heterogeneous decohesion and volume and porosity increase due to dilatancy. The band thickness is several grain sizes. At formation, the bands are not opened, so they are not mode I fractures. They become fractures with plumose fractography after the separation of the sample parts along the band. The formation mechanism of these discontinuities or fractures is not completely clear, but it is suggested that it represents a running constitutive instability in the form of dilatancy banding (with further σ increase the bands become inclined to σ1, i.e., shear). The similarity between the experimentally generated plumose surface fractures and natural joints is discussed, and it is suggested that they can be formed as propagating constitutive instabilities.
ISSN: 0148-0227

hal-00585846
https://hal.archives-ouvertes.fr/hal-00585846
DOI : 10.1029/2010JB008104

Éditeur(s) : HAL CCSD Elsevier
Résumé : Displacement-length data from faults, joints, veins, igneous dikes, shear deformation bands, and compaction bands define two groups. The first group, having a power-law scaling relation with a slope of n = 1 and therefore a linear dependence of maximum displacement and discontinuity length (D-max = gamma L), comprises faults and shear (non-compactional or non-dilational) deformation bands. These shearing-mode structures, having shearing strains that predominate over volumetric strains across them, grow under conditions of constant driving stress, with the magnitude of near-tip stress on the same order as the rock's yield strength in shear. The second group, having a power-law scaling relation with a slope of n = 0.5 and therefore a dependence of maximum displacement on the square root of discontinuity length (D-max = alpha L-0.5), comprises joints, veins, igneous dikes, cataclastic deformation bands, and compaction bands. These opening- and closing-mode structures grow under conditions of constant fracture toughness, implying significant amplification of near-tip stress within a zone of small-scale yielding at the discontinuity tip. Volumetric changes accommodated by grain fragmentation, and thus control of propagation by the rock's fracture toughness, are associated with scaling of predominantly dilational and compactional structures with an exponent of n = 0.5.
ISSN: 0191-8141

hal-00411173
https://hal.archives-ouvertes.fr/hal-00411173
DOI : 10.1016/j.jsg.2008.08.001

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Contractional deformation of highly porous sandstones is poorly explored, as compared to extensional deformation of such sedimentary rocks. In this work we explore the highly porous Aztec Sandstone in the footwall to the Muddy Mountain thrust in SE Nevada, which contains several types of deformation bands in the Buffington tectonic window: 1) Distributed centimeter-thick shear-enhanced compaction bands (SECBs) and 2) rare pure compaction bands (PCBs) in the most porous parts of the sandstone, cut by 3) thin cataclastic shear-dominated bands (CSBs) with local slip surfaces. Geometric and kinematic analysis of the SECBs, the PCBs and most of the CSBs shows that they formed during ∼E–W (∼100) shortening, consistent with thrusting related to the Cretaceous to early Paleogene Sevier orogeny of the North American Cordilleran thrust system. Based on stress path modeling, we suggest that the compactional bands (PCBs and SECBs) formed during contraction at relatively shallow burial depths, before or at early stages of emplacement of the Muddy Mountains thrust sheet. The younger cataclastic shear bands (CSBs, category 3), also related to E–W Sevier thrusting, are thinner and show larger shear offsets and thus more intense cataclasis, consistent with the initiation of cataclastic shear bands in somewhat less porous materials. Observations made in this work support earlier suggestions that contraction lead to more distributed band populations than what is commonly found in the extensional regime, and that shear-enhanced compaction bands are widespread only where porosity (and permeability) is high.
ISSN: 0191-8141

hal-01171854
https://hal.archives-ouvertes.fr/hal-01171854
DOI : 10.1016/j.jsg.2015.02.014

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
Determination of the membrane seal capacity of deformation bands is critical for managing geologic reservoirs in porous sandstones. In this study, we have analyzed a cataclastic shear-band network developed in uncemented porous sandstone in Provence, France. Geometrical analyses of the bands show significant differences between three types of bands (single strand, multistrand, and band cluster), sorted by their number of strands, their amount of shear displacement, and their thicknesses. At the microscopic scale, the image-analysis porosities and the grain-size distributions allow definition of three different types of microstructural deformation: damage zone, protocataclastic, and cataclastic. Whereas damage zone and protocataclastic deformations are observed in each type of band, cataclastic strands are observed in clusters and, sometimes, in multistrands. Cataclastic strands are characterized by a porosity reduction of 10 to 25% and a permeability reduction of three to five orders of magnitude compared to the host rock. Field observations of iron hydroxide precipitations around the bands suggest that cataclastic strands were membrane seals to water flow under vadose condition. This study therefore highlights the importance of the degree of cataclasis in shear bands as membrane seals to subsurface fluid flows in sandstone reservoirs.
ISSN: 0149-1423

hal-00766557
https://hal.archives-ouvertes.fr/hal-00766557
DOI : 10.1306/04051211097

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The analysis of three cataclastic band sets from Provence (France) reveals that the band density, their conjugate angles, their ratio of shear displacement to compaction, and the amount of cataclasis within the bands differ and can be expressed as functions of tectonic setting and petrophysical properties. We identify (1) a dense and closely spaced network of shear-enhanced (reverse) compaction bands; (2) a regularly spaced less dense network of reverse compactional shear bands; and (3) a localized network of normal shear bands. The field data show that strain localization is favored in an extensional regime and is characterized by shear bands with a large shear to compaction ratio and a small conjugate band angle. In contrast, distributed strain is favored in a contractional regime and is characterized by compactional bands with a low ratio of shear to compaction and a large conjugate band angle. To explain the mechanical origin of this strain localization, we quantify the yield strength and the stress evolution in extensional and contractional regimes in a frictional porous granular material. We propose a model of strain localization in porous sands as a function of tectonic stresses, burial depth, material properties, strain hardening and fluid pressure. Our model suggests that stress reduction, inherent to extensional regime, favors strain localization as shear bands, whereas stress increase during contraction favors development of compactional bands.
ISSN: 0191-8141

hal-00856921
https://hal.archives-ouvertes.fr/hal-00856921
DOI : 10.1016/j.jsg.2012.11.011

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Displacement-length data from dilatant fractures (joints, veins, igneous dikes) and several varieties of deformation bands were analyzed statistically to investigate the applicability of mechanical models proposed for their formation. All 17 datasets are generally consistent with equilibrium or long-term power-law slopes on the displacement-length diagram of either 1.0 or 0.5. Similar to many faults, disaggregation deformation bands are consistent with a power-law scaling relation having a slope of approximately c = 1, implying a linear dependence of maximum displacement and discontinuity length (Dmax = γL). In contrast, dilatant fractures, cataclastic deformation bands, and shear-enhanced compaction bands are consistent with a power-law scaling relation with a slope of approximately c = 0.5, implying a dependence of maximum displacement on the square root of length (Dmax = αL1/2). The scaling relations represent an average, or long-term equilibrium outcome of deformation for conditions such as length-scale, time-scale, temperature, chemistry, and an effectively homogeneous far-field stress field, allowing for variations such as rapid and/or localized behaviors. The displacement-length scaling of these geologic structures follows systematic relationships that provide information on host-rock properties and the physics of fracture and deformation-band propagation.
ISSN: 0191-8141

hal-00818130
https://hal.archives-ouvertes.fr/hal-00818130
DOI : 10.1016/j.jsg.2012.12.005

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Field observations of highly porous and permeable sandstone in the Orange area (S-E Basin, France) show that networks of shear-enhanced compaction bands can form in a contractional regime at burial depths of about 400 m ± 100 m. These bands show equal compaction and shear displacements, are organized in conjugate and densely distributed networks, and are restricted to the coarse-grained (mean grain diameter of 0.6 ± 0.1 mm) and less porous (porosity of 26 ± 2%) sand layers. The bands are crush microbreccia with limited grain comminution and high grain microfracture density. They show reductions of permeability (mD) ranging from 0 to little more than 1 order of magnitude. They show no control on the alteration products related to meteoric water flow, which suggests that these shear-enhanced compaction bands have no or only negligible influence on subsurface fluid flow. Their selective occurrence and small (20%) reduction in transmissibility in densely populated layers prevented them from compartmentalizing the sandstone reservoirs. A comparison with compaction-band populations in the Navajo and Aztec sandtsones (western U.S.) emphasizes the role of burial depth and the presence of chemical compaction processes for the sealing potential of deformation bands.
ISSN: 0191-8141

hal-00807309
https://hal.archives-ouvertes.fr/hal-00807309
DOI : 10.1016/j.jsg.2012.11.008

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Both oedometric and plane-strain tests were performed with parallelepipedic samples made of synthetic granular, cohesive, frictional and dilatant rock analogue material GRAM2. For the first time parallel sets of fractures that have all the characteristics of natural joints were reproduced in the laboratory. The fractures are regularly spaced, normal to σ3, and have plumose morphology very similar to that of natural joints. These fractures can form at tensile stress σ3 much smaller in magnitude than the tensile strength of material and even at slightly compressive σ3. When mean stress σ exceeds a certain value, the fractures become oblique to σ1 (the obliquity increases with σ), forming networks of conjugate shear bands/fractures. These results of plane-strain experiments are in good agreement with those of better controlled conventional axisymmetric tests on a similar material in Chemenda et al. (2011b) and are closer to real geological situations. Both types of experiments are complementary. Their results lead to the conclusion that at least certain categories of natural fractures (including joints, and conjugate shear fractures/bands) were initiated as deformation localization bands. The band orientation is defined by the constitutive properties/parameters (notably the dilatancy factor) that are sensitive to σ.
ISSN: 0040-1951

hal-00795555
https://hal.archives-ouvertes.fr/hal-00795555
DOI : 10.1016/j.tecto.2011.11.021

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We studied the deformation in a partially molten mantle through detailed petrostructural analysis of plagioclase lherzolites from the northwestern part of the central Lanzo massif. These peridotites display a pervasive anastomosed network of millimetre to centimetre-scale plagioclase-rich bands, which grades locally into a planar layering marked by an intercalation of plagioclase-rich and olivine-rich layers up to tens of centimetres wide. Both the anastomosed and the planar layering are subparallel to the deformation fabric, characterized by a foliation defined by the shape-preferred orientation of olivine and by crystal preferred orientation (CPO) of olivine, orthopyroxene, and clinopyroxene. This parallelism, the coexistence of microstructural evidence for melt-rock reactions and for deformation by dislocation creep, and the predominance of axial-[010] olivine CPO patterns, characterized by [010] axes clustered normal to the layering, indicate that deformation and the reactive melt percolation that formed the layering were coeval. Strong heterogeneity in mineral composition in the planar layering domains, with Fe-enrichment in olivine and spinel and highly variable Ti content in spinel in cm-scale plagioclase-rich bands, implies that the latter interacted with higher melt volumes. High Ti contents in pyroxenes and spinel in the anastomosed layering domains point to changes in melt composition, hinting to less effective melt transport. We propose therefore that the planar layering records melt segregation in layers parallel to the shear plane, whereas the anastomosed layering results from melt alignment along grain boundaries subparallel to the shear plane, without segregation. Finite strain in the different layers cannot be quantified, but comparison of the present observations with data from experiments and from other mantle outcrops displaying shear-controlled melt organization suggests that the transition from the anastomosed to the planar layering might record an increase in finite strain, that is, strain localization associated with variations in the instantaneous melt fraction.
ISSN: 0040-1951

hal-01053509
https://hal.archives-ouvertes.fr/hal-01053509
DOI : 10.1016/j.tecto.2014.01.007

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Despite decades of petrological and geochemical studies, the nature and setting of obducted ophiolites remain controversial: the influence of supra-subduction zone environments on pre-existing oceanic lithosphere is yet to assess, and the processes leading to subduction/obduction initiation are still poorly constrained. Our study documents successive influx of slab-derived fluids and progressive strain localization within the upper mantle in a supra-subduction environment during the first few My of the subduction history. We focus on strongly sheared mafic amphibolites intruding peridotites near the mantle–crust transition of the New Caledonia obducted ophiolite and ~ 50 to 100 m above the basal thrust contact of the ophiolite. These m- to hm-long and several m-thick shear bands are interpreted as inherited small-scale intrusions of mafic melts, probably dikes or sills, which were derived from a moderately refractory mantle source refertilized by supra-subduction zone fluids. 40Ar/39Ar age constraints on pargasite at ca. 90 Ma suggest that they could be inherited from the former Pacific west-dipping subduction.Secondary deformation of these mafic intrusions is intimately associated to three major stages of fluid infiltration: (1) the first stage of deformation and metasomatism is marked by syn-kinematic growth of Ca-amphibole (at 700–800 °C and 3–5 kbar) with a distinctive supra-subduction zone signature, and controlled later channelization of aqueous fluids. 40Ar/39Ar dating on magnesio-hornblende indicates that this deformation episode occurred at ca. 55 Ma, coincident with east-dipping subduction initiation; (2) the main metasomatic stage, characterized by the development of a phlogopite-rich matrix wrapping peridotites and amphibolite boudins, points to the percolation of alkali-rich aqueous fluids at still high temperature (650–750 °C); (3) the last, low temperature (< 600 °C) metasomatic stage results in the formation of deformed veinlets containing talc, chlorite and serpentine.
ISSN: 0024-4937

hal-01306664
https://hal.archives-ouvertes.fr/hal-01306664
https://hal.archives-ouvertes.fr/hal-01306664/document
https://hal.archives-ouvertes.fr/hal-01306664/file/Soret_2016_Strain_localization.pdf
DOI : 10.1016/j.lithos.2015.11.022

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Improving the prediction of sub-seismic structures and their petrophysical properties is essential for realistic characterization of deformed sandstone reservoirs. In the present paper, we describe permeability contrasts induced by cataclastic deformation bands and faults in porous sandstones (766 data synthesized from field examples and the literature). We also discuss the influence of several factors, including tectonic regime, presence of a fault, burial depth, host sandstone porosity, and grain size and sorting for their initiation and permeability. This analysis confirms that permeability decrease is as a function of grain-crushing intensity in bands. Permeability reduction ranges from very limited in crush-microbreccia of compaction bands to high permeability reduction in cataclasites and ultracataclasites of shear-dominated bands, band clusters and faults. Tectonic regime, and especially normal-fault regime, with its tendency to localize strain and generate faults, is identified as the most important factor, leading to the formation of cataclastic bands with high permeability contrasts. Moreover, moderate burial depth (1–3 km) favors cataclastic bands with high permeability contrasts with respect to the host sandstone. High porosity, coarse-grain size and good grain sorting can slightly amplify the permeability reductions recorded in bands.
ISSN: 0191-8141

hal-01218408
https://hal.archives-ouvertes.fr/hal-01218408
DOI : 10.1016/j.jsg.2015.03.013

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Analysis of the microstructures in the km-scale mantle shear zone that separates the northern and the central parts of the Lanzo peridotite massif provides evidence of an evolution in time and space of deformation processes accommodating shearing in the shallow mantle within an extensional setting. This shear zone displays an asymmetric distribution of deformation facies. From south to north, gradual reorientation of the foliation of coarse porphyroclastic plagioclase-bearing peridotites is followed by development of protomylonites, mylonites, and mm-scale ultramylonite bands. A sharp grain size gradient marks the northern boundary. Early deformation under near-solidus conditions in the south is recorded by preservation of weakly deformed interstitial plagioclase and almost random clinopyroxene and plagioclase crystal orientations. Feedback between deformation and melt transport probably led to melt focusing and strain weakening in the shear zone. Overprint of melt-rock reaction microstructures by solid-state deformation and decrease in recrystallized grain size in the protomylonites and mylonites indicate continued deformation under decreasing temperature. Less enriched peridotite compositions and absence of ultramafic dykes or widespread melt-impregnation microstructures north of the shear zone and clinopyroxene and amphibole enrichment in the mylonites and ultramylonites suggest that the shear zone acted as both a thermal barrier and a high-permeability channel for late crystallizing fluids. These observations, together with chemical data indicating faster cooling of central Lanzo relative to the northern body, corroborate that this shear zone is a mantle detachment fault. All deformation facies have crystal preferred orientations consistent with deformation by dislocation creep with dominant activation of the (010)[100] and (100)[001] systems in olivine and orthopyroxene, respectively. Dynamic recrystallization produces dispersion of olivine CPO but not a change of dominant deformation mechanism. Evidence for activation of grain boundary sliding is limited to mm-scale ultramylonite bands, where solid-state reactions produced very fine grained polymineralic aggregates. Except for these latest stages of deformation, strain localization does not result from the microstructural evolution; the grain size decrease is a consequence of the need to deform a rock volume whose strength continuously increases because of decreasing temperature conditions. Strain localization in the intermediate levels thus essentially results from the more localizing behavior of both the deep, partially molten, and shallow parts of this extensional shear zone distribution.
ISSN: 1525-2027

hal-00644844
https://hal.archives-ouvertes.fr/hal-00644844
DOI : 10.1029/2011GC003627

Éditeur(s) : HAL CCSD
Résumé : This work provides new constraints on the interactions between deformation and percolation of melt or fluids, as well as on the implications of these processes for the seismic properties of the mantle wedge. It is based on the analysis of spinel peridotites from the massif of Ronda (Spain) and two xenolith suites from active subduction zones (Kamchatka, Papua New Guinea). A coupled structural, petrological and geochemical study of these samples shows that they underwent a reactive percolation of melts or Si-rich fluids, which was synchronous to a deformation event occurring under high temperature and low stress conditions, consistent with the PT conditions at the base of the lithosphere or in the asthenosphere. This reactive percolation is responsible for enrichment in pyroxenes, mainly orthopyroxene, which is often localized in bands parallel to the high-temperature foliation. This enrichment is associated with grain size reduction and dispersion of the crystallographic orientation of olivine. The dominant slip system in olivine is {0kl}[100], which results in fast S-wave polarization parallel to the flow direction in the mantle. The decrease in the intensity of the olivine crystal preferred orientations associated with the enrichment in pyroxene results in significant decrease of the anisotropy that may induce an underestimation of the thickness of the anisotropic layer by up to 33%. The observed orthopyroxene enrichment also lowers the Vp/Vs ratio, but cannot explain Vp/Vs < 1.7 mapped locally in the fore-arc mantle in Japan and the Andes. Such low Vp/Vs ratios may however be explained by considering the intrinsic anisotropy of the peridotites, which is generally ignored in large-scale Vp/Vs ratio mapping of the mantle wedge. Infrared analyses show that olivine from the both xenolith collections contains less water than the theoretical saturation calculated for their estimated equilibrium temperature in the spinel stability field. These low water content are similar to those observed in spinel peridotites from other subduction zones and probably record both the low solubility of water in olivine at relatively low pressure and dehydration during exhumation of the xenoliths. These measured water contents as well as theoretical saturation estimations are not sufficient to change the dominant slip direction of in olivine from [100] to [001].
Ce travail apporte de nouvelles contraintes sur les interactions entre déformation et processus d'hydratation et de percolation de magma ou de fluides dans le manteau à l'aplomb d'une zone de subduction et leurs implications sur les propriétés sismiques dans le coin mantellique. Il se base sur l'analyse de péridotites à spinelle provenant du massif de Ronda (Espagne) et deux séries de xénolites issues de zones de subduction actives (Kamchatka, Papouasie-Nouvelle-Guinée). L'étude structurale, pétrologique et géochimique de ces échantillons montrent qu'ils ont subit une percolation réactive de magma ou de fluide synchrone d'une déformation de haute température basse contrainte cohérente avec les condition PT de la base de la lithosphère ou de l'asthénosphère. Cette percolation réactive est responsable d'un enrichissement en pyroxènes, qui est souvent localisé dans des bandes parallèles à la foliation. Cet enrichissement est associé à une dispersion de l'orientation cristallographique de l'olivine. Les systèmes de glissement dominant dans l'olivine sont dans tous les cas {0kl}[100], ce qui implique que la direction de polarisation rapide des ondes S dans la partie supérieure du coin mantellique est parallèle à la direction d'écoulement dans le manteau. La décroissance de l'intensité des OPR de l'olivine associée à l'enrichissement en pyroxènes a pour conséquence une réduction non négligeable de l'anisotropie sismique qui peut induire jusqu'à 33% d'erreur sur l'interprétation de l'épaisseur de la couche anisotrope. Un enrichissement en orthopyroxène peut aussi entraîner une baisse du rapport Vp/Vs, mais ne peut expliquer les rapports Vp/Vs <1,7 cartés dans certains avant-arcs. Cependant de telles valeurs peuvent être expliquées si l'anisotropie des péridotites du coin mantellique est prise en compte. Les analyses par spectroscopie infra-rouge montrent que les olivines des deux séries de xénolites étudiées contiennent moins d'eau que la saturation théorique calculée pour leurs températures d'équilibre dans le domaine du spinelle. Ces faibles concentrations en eau sont similaires à celles observées dans les olivines des péridotites à spinelle des autres zones de subduction. Elles enregistrent probablement la faible solubilité de l'eau dans l'olivine à des pressions relativement basses et la déshydratation au cours de l'exhumation des xénolites. Ces teneurs en eau mesurées ainsi que les estimations de la saturation théorique ne sont pas suffisantes pour changer la direction de glissement dominante dans l'olivine de [100] à [001].
https://tel.archives-ouvertes.fr/tel-00689832

tel-00689832
https://tel.archives-ouvertes.fr/tel-00689832
https://tel.archives-ouvertes.fr/tel-00689832/document
https://tel.archives-ouvertes.fr/tel-00689832/file/These-Soustelle2010.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Regional-scale deformation taking place in a strongly anisotropic, yet homogeneous metapelitic protolith during an apparently single tectonic event was systematically investigated as a function of the distance to the main tectonic contact (i.e., the Filabres shear zone, a major detachment in the Betic Cordilleras, Spain). The density of C3' shear bands (or extensional crenulation cleavage) reworking the earlier S2 schistosity increases exponentially towards the contact, in parallel with the decrease in the size of the shear domains. Systematic variations in angles and shape ratios are also reported. Deformation and age patterns, however, suggest that this spectacular trend at least partly results from a progressive localization of the deformation through time. This fossilized shear strain gradient was thus produced somewhat diachronously. Such shear strain patterns nevertheless provide a mean to constrain the rheological properties for such weak lithologies and a mean to better understand crustal deformation.
ISSN: 0191-8141

insu-00545043
https://hal-insu.archives-ouvertes.fr/insu-00545043
https://hal-insu.archives-ouvertes.fr/insu-00545043/document
https://hal-insu.archives-ouvertes.fr/insu-00545043/file/JSGagardetal2.pdf
DOI : 10.1016/j.jsg.2010.11.011