Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : International audience
Recent mathematical calculations allow us to define set fracture intensity (I), i.e., the amount of rock mass affected by fracture sets, independently of the investigation mode. This parameter, characteristic of each rock mass, is of much interest to describe the mechanical response of the rock mass to external influences. The aim of this work is to apply these mathematical equations on one site using measurements of three distinct fracture sets: (1) on a plane surface, (2) along a scanline, and (3) using borehole imaging, in order to evaluate and explain variability in collected data. Even if the three types of measurements give differences on absolute intensity values, they still define similar trends, i.e., the order of the fracturing impact of joint sets is the same from the three measurement methods, irrespective of the fact that obtained values are quite different from one survey method to another. We discuss the possible origins of these biases.
ISSN: 1435-9529

hal-01121556
https://hal.archives-ouvertes.fr/hal-01121556
DOI : 10.1007/s10064-014-0572-1

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Both oedometric and plane-strain tests were performed with parallelepipedic samples made of synthetic granular, cohesive, frictional and dilatant rock analogue material GRAM2. For the first time parallel sets of fractures that have all the characteristics of natural joints were reproduced in the laboratory. The fractures are regularly spaced, normal to σ3, and have plumose morphology very similar to that of natural joints. These fractures can form at tensile stress σ3 much smaller in magnitude than the tensile strength of material and even at slightly compressive σ3. When mean stress σ exceeds a certain value, the fractures become oblique to σ1 (the obliquity increases with σ), forming networks of conjugate shear bands/fractures. These results of plane-strain experiments are in good agreement with those of better controlled conventional axisymmetric tests on a similar material in Chemenda et al. (2011b) and are closer to real geological situations. Both types of experiments are complementary. Their results lead to the conclusion that at least certain categories of natural fractures (including joints, and conjugate shear fractures/bands) were initiated as deformation localization bands. The band orientation is defined by the constitutive properties/parameters (notably the dilatancy factor) that are sensitive to σ.
ISSN: 0040-1951

hal-00795555
https://hal.archives-ouvertes.fr/hal-00795555
DOI : 10.1016/j.tecto.2011.11.021

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Large sand intrusions often exhibit conical morphologies analogous to magmatic intrusions such as saucer-shaped or cup-shaped sills. Whereas some physical processes may be similar, we show with scaled experiments that the formation of conical sand intrusions may be favoured by the pore-pressure gradients prevailing in the host rock before sand injection. Our experiments involve injecting air into a permeable and cohesive analogue material to produce hydraulic fractures while controlling the pore pressure field. We control the state of overpressure in the overburden by applying homogeneous basal pore pressure, and then adding a second local pore pressure field by injecting air via a central injector to initiate hydraulic fractures near the injection point. In experiments involving small vertical effective stresses (small overburden, or high pore fluid overpressure), the fracturing pressure (lambda(fract)) is supralithostatic and two dipping fractures are initiated at the injection point forming a conical structure. From theoretical considerations, we predict that high values of lambda(fract), are due to strong cohesion or high pore fluid overpressure distributed in the overburden. Such conditions are favoured by the pore pressure/stress coupling induced by both pore pressure fields. The dips of cones can be accounted for elastic-stress rotation occurring around the source. Contrary to magmatic chamber models, the aqueous fluid overpressure developed in a parent sandbody (and prevailing before the formation of injectites) may diffuse into the surrounding overburden, thus favouring stress rotation and the formation of inclined sheets far from the parent source. For experiments involving higher vertical effective stresses (thick overburden or low pore fluid overpressure), the fracturing pressure is lower than the lithostatic stress, and a single fracture is opened in mode I which then grows vertically. At a critical depth, the fracture separates into two dilatant branches forming a flat cone. We make use of a P.I.V. (Particle Imaging Velocimetiy) technique to analyse plastic deformation, showing that these inclined fractures are opened in mixed modes. Close to the surface, they change into steep shear bands where fluids can infiltrate. The final morphology of the fracture network is very similar to the common tripartite architecture of various injection complexes, indicating that different mechanisms may be involved in the formation of dykes. Feeder dykes under the sill zones may open as tensile fractures, while overlying dykes may be guided by the deformation induced by the growth of sills. These deformation conditions may also favour the formation of fluid escape structures and pockmarks. (C) 2011 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00745640
https://hal.archives-ouvertes.fr/hal-00745640
DOI : 10.1016/j.epsl.2011.10.029

Éditeur(s) : HAL CCSD Techno-Press
Résumé : Fractures and faults riddle the Earth’s crust on all scales, and the deformation associated with them is presumed to have had significant effects on its petrological and structural evolution. However, despite the abundance of directly observable earthquake activity, unequivocal evidence for seismic slip rates along ancient faults is rare and usually related to frictional melting and the formation of pseudotachylites. We report novel microstructures from garnet crystals in the immediate vicinity of seismic slip planes that transected lower crustal granulites during intermediate-depth earthquakes in the Bergen Arcs area, western Norway, some 420 million years ago. Seismic loading caused massive dislocation formations and fragmentation of wall rock garnets. Microfracturing and the injection of sulfide melts occurred during an early stage of loading. Subsequent dilation caused pervasive transport of fluids into the garnets along a network of microfractures, dislocations, and subgrain and grain boundaries, leading to the growth of abundant mineral inclusions inside the fragmented garnets. Recrystallization by grain boundary migration closed most of the pores and fractures generated by the seismic event. This wall rock alteration represents the initial stages of an earthquake-triggered metamorphic transformation process that ultimately led to reworking of the lower crust on a regional scale.
ISSN: 2287-528X

hal-01553309
https://hal.archives-ouvertes.fr/hal-01553309
https://hal.archives-ouvertes.fr/hal-01553309/document
https://hal.archives-ouvertes.fr/hal-01553309/file/austrheim2017.pdf
DOI : 10.1126/sciadv.1602067

Éditeur(s) : HAL CCSD
Résumé : Sand intrusions (or injectites) are most often the product of post-depositional remobilization of sand leading to its injection into the surrounding rocks. While injectites were recognized for the first time nearly 200 years ago, their emplacement process has been studied for a couple of decades only, since the concepts of deep sea depositional environments have allowed us to better understand their emplacement processes. However, these processes are still relatively poorly understood. Our approach is based on the study of injectites in the Lower Congo Basin from seismic and well data, which we compare to a fossil system in the SE France basin. We have shown that: (1) In buried turbidite channel systems draping deposits on the channel flanks and terraces of channels have the same geophysical signature as 'wing-like' injectites. Finally, the only criterion for identifying seismic injectites is the presence of bedding-discordant seismic reflections, and in the best case the associated uplift of the overlying seismic reflectors. (2) Seismic-scale conical and saucer-shaped sand injectites have been identified in the Lower Congo Basin. The remobilization is likely due to overpressuring induced by the buoyancy effect of hydrocarbons trapped in the margins of a lobe buried underneath 160 m of sediment, followed by the sudden injection of fluidized sand associated with fault reactivation of faults (with a possible role of nearby salt diapirs). (3) A network of injectites (dykes, sills/wings and laccoliths) was formed in the Vocontian basin during the late Albian and/or early Cenomanian, from a lower-middle Albian turbidite channel. The emplacement is probably due to the early compartmentalization of the channel during its burial and the increase of the sedimentation rate generating overpressure; and the subsequent large influx of deep fluids triggering injection. The injection of sand was polyphased: a first episode formed the sills and another emplaced the dykes. Sills/wings and dykes propagated about 2 km laterally away from the parent sand body and about 200 m up to the surface, revealing a much more extended lateral than vertical reach, contrary to the classically accepted idea from the interpretation of seismic data. (4) The emplacement of this large network of injectites was governed by hydrofracturing. Therefore, its morphology is dependent on the host rock heterogeneity (isotropy, fractures), the paleo-stress orientation (ó3 = NW-SE) and the burial depth of the source (300-600 m) at the time of injection. The study of this fossil network allows us to define the relationship between morphology of the injected network and stress state at the time of injection. This relationship can be extrapolated to constrain the morphology of subsurface networks beyond seismicvisibility. (5) Sands injected into low permeability lithologies bear evidence to a major event of fluid escape in the studied basin, but also channeled fluids long after their formation. In this way, injectites both attest to specific episodes of fluid migration in sedimentary basins and contribute to long-lived re-routing of migrating fluids once emplaced. The injection of sand is associated with the sudden escape of fluids, probably resulting from a significant tectonic and/or sedimentary event; in addition, the architecture of injectite networks is governed by the local paleo-stress and heterogeneity in the host rock. Consequently, characterizing injectite networks is an important step in understanding the plumbing systems of continental margins, i.e. the post-depositional evolution of sedimentary basins.
Les intrusions sableuses (ou injectites) sont le plus souvent le produit de la remobilisation post-dépositionnelle des sédiments et de l'injection du sable dans les roches environnantes. Bien que reconnues pour la première fois il y a près de 200 ans, elles ne sont réellement étudiées que depuis quelques dizaines d'années, depuis que les concepts sur les environnements de dépôt dans les domaines marins profonds nous permettent de mieux comprendre les processus de mise en place. Cependant, ces processus restent encore aujourd'hui relativement mal compris. Notre approche repose sur l'étude d'injectites dans le bassin du Bas-Congo a partir de données de sismique et de puits que nous comparerons a un système fossile dans le bassin du SE de la France. Nous avons montre que : (1) Dans des systèmes de chenaux turbiditiques enfouis, les dépôts de drapage sur les marges et terrasses de chenaux présentent la même signature géophysique que les injectites de type "wing". Finalement, le seul critère sismique d'identification des injectites est la présence de réflexions sismiques sécantes vis-a-vis de la stratigraphie associée dans le meilleur des cas au soulèvement des réflecteurs sismiques sus-jacents. (2) Des injectites d'échelle sismique en forme de cône et d'assiette ont été identifiées dans le bassin du Bas-Congo. La remobilisation résulte probablement des pressions anormales induites par l'effet de flottabilité des hydrocarbures piégés dans les marges d'un lobe enfoui sous 160 m de sédiment, puis de l'injection soudaine du sable fluidise associée a la réactivation de failles (possible rôle des diapirs de sel a proximité). (3) Un réseau d'injectites (dykes, sills/wings et laccolites) s'est formé dans le bassin Vocontien entre la fin de l'Albien supérieur et/ou le début du Cénomanien, depuis un chenal turbiditique de l'Albien inférieur-moyen. La mise en place résulte probablement de la compartimentalisation précoce du chenal au cours de son enfouissement et de l'augmentation du taux de sédimentation générant la surpression et de l'apport ulterieur d'importante quantité de fluides profonds déclenchant l'injection. L'injection du sable a été polyphasée : une première injection a formé des sills et une suivante des dykes. Les sills/wings et les dykes se sont propagés latéralement au chenal source sur environ 2 km et vers la surface sur environ 200 m, mettant en évidence une forte remobilisation latérale plutôt que verticale, contrairement a l'idée classiquement admise a partir de l'interprétation des données sismiques. (4) La formation de ce large réseau d'injectites a été gouvernée par des mécanismes d'hydrofracturation. Par conséquent, sa morphologie a été dépendante des hétérogenéités de la roche hôte (milieu isotrope, fracture), des directions de paléo-contraintes (ƒÐ3 = NWSE) et de la profondeur d'enfouissement de la source (300-600 m) au moment de l'injection. L'étude de ce réseau fossile permet de définir les relations entre morphologie du réseau injecté et état de contraintes au moment de l'injection. Cette relation peut être extrapolée de façon à contraindre la morphologie des réseaux de subsurface au-delà de la visibilité sismique. (5) Les sables injectés dans des lithologies de faible perméabilité témoignent d'un épisode d'échappement de fluide important dans les bassins étudiés mais ont aussi guide les fluides longtemps après leur formation. Les injectites contribuent ainsi a l'initiation épisodique et la pérennisation de migrations de fluides dans les bassins sedimentaires. Le processus d'injection est associé a l'échappement brutal de fluides, résultant vraisemblablement d'un évènement tectonique et/ou sédimentaire important, et l'architecture des réseaux d'injectites est gouverné par les paléo-contraintes locales et les hétérogénéités de la roche hôte. Par conséquent, la caractérisation des réseaux d'injectites est une étape importante dans la compréhension de la plomberie des marges, c'est-a-dire l'évolution post-dépôt des bassins sédimentaires.
https://tel.archives-ouvertes.fr/tel-01011486

tel-01011486
https://tel.archives-ouvertes.fr/tel-01011486
https://tel.archives-ouvertes.fr/tel-01011486/document
https://tel.archives-ouvertes.fr/tel-01011486/file/These_Monnier_2013_banalisee.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A large sand injectite network is very well exposed in the area of Bevons, Southeast France. The associated sandstone turbiditic channel–fill and the host marls are the Aptian–Albian rocks of the Vocontian Basin. The sand injection network is composed of dykes, sills and sedimentary laccoliths ranging in thickness from mm to pluri–m. The dykes and sills have vertical and horizontal lengths of up to and over 100 m and 1 km, respectively. Outcrop observations show that the architecture and morphology of the sand injectites in the marls is governed by the local stress field during injection, pre–existing faults, the host–rock lithology, compaction, and distance to the potential sand source(s). The main set of dykes is oriented N50–60° perpendicular to the minimum compressive stress σ3 during sand injection. Two other sets of dykes are intruded along pre–existing syn–sedimentary faults oriented N140–150° (set 2) and N90° (set 3) during the Apto–Cenomanian interval. Sills and dykes thin laterally away from their potential sand sources and thin laterally away from them. The vertical thickness variations of the dykes and wings are more complex, as thinning away from the sand sources is often compensated by thickening toward the palaeo–surface. Based on field observations and measurements, we characterized the 3D architecture of the sand injectites and showed that the injectites probably formed due to a forceful injection from an overpressured sand body sealed by low–permeability lithologies.
ISSN: 0191-8141

hal-01243488
https://hal.archives-ouvertes.fr/hal-01243488
DOI : 10.1016/j.jsg.2015.07.001

Éditeur(s) : HAL CCSD
Résumé : 1 p.
For groundwater issues (potential leakages in waste repository, aquifer management ...), the development of modeling techniques is far ahead of the actual knowledge of aquifers. This raises two fundamental issues: 1) which and how much data are necessary to make predictions accurate enough for aquifer management issues; 2) which models remain relevant to describe the heterogeneity and complexity of geological systems. The French observatory H+ was created in 2002 with the twofold motivation of acquiring a large database for validating models of heterogeneous aquifers, and of surveying groundwater quality evolution in the context of environmental changes. H+ is a network of 4 sites (Ploemeur, Brittany, France; HES Poitiers, France; Cadarache, France; Campos, Mallorca, Spain) with different geological, climatic, and economic contexts. All of them are characterized by a highly heterogeneous structure (fractured crystalline basement for Ploemeur, karstified and fractured limestone for Poitiers, Cadarache and Mallorca), which is far to be taken into account by basic models. Ploemeur is exploited as a tap-water plant for a medium-size coastal city (15,000 inhabitants) for 20 years. Each site is developed for long term investigation and monitoring. They involves a dense network of boreholes, detailed geological and geophysical surveys, periodic campaigns and/or permanent measurements of groundwater flow, water chemistry, geophysical signals (including ground motions), climatic parameter, etc. Several large-scale flow experiments are scheduled per year to investigate the aquifer structure with combined geophysical, hydrogeological, and geochemical instruments. All this information is recorded in a database that has been developed to improve the sustainability and quality of data, and to be used as a collaborative tool for both site researchers and modelers. This project lasts now for 5 years. It is a short time to collect the amount of information necessary to apprehend the complexity of aquifers; but it is already enough to obtain a few important scientific results about the very nature of the flow heterogeneity, the origin and residence time of water elements, the kinetic of geochemical processes, etc. We have also developed new methods to investigate aquifers (in-situ flow measurements, flow experiment designs, groundwater dating, versatile in-situ probes, etc.). This experience aiming at building up long term knowledge appears extremely useful to address critical issues related to groundwater aquifers: the structure and occurrence of productive aquifer in crystalline basement, the assessment of aquifer protection area in the context of highly heterogeneous flow, the biochemical reactivity processes, the long term evolution of both water quantity and quality in the context of significant environmental changes, for instance.
AGU, Fall Meeting 2008
San Francisco, United States

insu-00375980
https://hal-insu.archives-ouvertes.fr/insu-00375980

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
The outstanding exposure of deformation bands in a multilayer sequence of the Orange quarry, Provence, France, motivates a study investigating the development and controls of deformation band geometries by field mapping combined with finite element modeling. Field mapping yields new insights into angular relations between, and evolution of, the deformation bands as well as provides input parameters for the setup and boundary conditions of the numerical simulations using ADELI 2D. In particular, reverse-sense deformation bands are found to have developed within three of the four exposed layers of the multilayer stack with similar orientations to bedding, indicating layer-parallel contraction. Numerical simulations, carried out as a parametric study to investigate the influence on deformation band development and geometry, successfully reproduce the sequential development of deformation bands in the three layers as seen in the field as well as recreate the observed angular geometries of similar to 39 degrees to the maximum compression. This angular relationship is put into context with observations from other field studies and theoretical values to explore controls of deformation band orientations. Furthermore, band localization is impeded in the model by increased layer cohesive strength, demonstrating the importance of host-rock property variations on where localization of bands within the multilayer sequence. Results from both field investigation and numerical simulations are consistent with regional tectonics, where the strata underwent gentle folding due to thrust faulting at depth, and bring further insight into the development and geometry of deformation bands in both extensional and contractional tectonic regimes.
ISSN: 0148-0227

hal-00639452
https://hal.archives-ouvertes.fr/hal-00639452
DOI : 10.1029/2011JB008365

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Upper-mantle flow beneath the South Pacific is investigated by analysing shear wave splitting parameters at eight permanent long-period and broad-band seismic stations and 10 broad-band stations deployed in French Polynesia from 2001 to 2005 in the framework of the Polynesian Lithosphere and Upper Mantle Experiment (PLUME). Despite the small number of eventsand the rather poor backazimuthal coverage due to the geographical distribution of the natural seismicity, upper-mantle seismic anisotropy has been detected at all stations except at Tahiti where two permanent stations with 15 yr of data show an apparent isotropy. The median value of fast polarization azimuths (N67.5°W) is parallel to the present Pacific absolute platemotion direction in French Polynesia (APM: N67°W). This suggests that the observed SKS fast polarization directions result mainly from olivine crystal preferred orientations produced by deformation in the sublithospheric mantle due to viscous entrainment by the moving Pacific Plate and preserved in the lithosphere as the plate cools. However, analysis of individualmeasurements highlights variations of splitting parameters with event backazimuth that imply an actual upper-mantle structure more complex than a single anisotropic layer with horizontal fast axis. A forward approach shows that a two-layer structure of anisotropy beneath French Polynesia better explains the splitting observations than a single anisotropic layer. Second ordervariations in the measurements may also indicate the presence of small-scale lateral heterogeneities. The influence of plumes or fracture zones within the studied area does not appear to dominate the large-scale anisotropy pattern but may explain these second-order splitting variations across the network.
ISSN: 0956-540X

hal-01249275
https://hal.archives-ouvertes.fr/hal-01249275
https://hal.archives-ouvertes.fr/hal-01249275/document
https://hal.archives-ouvertes.fr/hal-01249275/file/GJI2007SKS.pdf
DOI : 10.1111/j.1365-246X.2007.03475.x

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
An analytical solution in the Laplace domain is derived for modeling anomalous pressure diffusion during pumping tests in aquifer displaying hierarchical fractal fracture networks. The proposed solution generalizes all of the analytical models for fractal flow published previously by combining multifractal diffusion and nested multiporosity with transient exchanges, interface skin effects, and well storage effect. Solutions are derived for fracture-delimited blocks with planar, cylindrical, and spherical shapes, as well as with any fractional dimensional shapes. Any combinations of these shapes can be defined in order to model a large range of situations. Within each permeability level, the fractal properties of the fracture network can be specified and the fractal dimension can be distinct from the shape dimension of the block.
ISSN: 0043-1397

hal-00411549
https://hal.archives-ouvertes.fr/hal-00411549
DOI : 10.1029/2008WR007125

Éditeur(s) : HAL CCSD
Résumé : International audience
Characterizing the hydraulic properties of heterogeneous and complex aquifers often requires field scale investigations at multiple space and time scales to better constrain hydraulic property estimates. Here, we present and discuss results from the site of Ploemeur (Brittany, France) where complementary hydrological and geophysical approaches have been combined to characterize the hydrogeological functioning of this highly fractured crystalline rock aquifer. In particular, we show how cross-borehole flowmeter tests, pumping tests and frequency domain analysis of groundwater levels allow quantifying the hydraulic properties of the aquifer at different scales. In complement, we used groundwater temperature as an excellent tracer for characterizing groundwater flow. At the site scale, measurements of ground surface deformation through long-base tiltmeters provide robust estimates of aquifer storage and allow identifying the active structures where groundwater pressure changes occur, including those acting during recharge process. Finally, a numerical model of the site that combines hydraulic data and groundwater ages confirms the geometry of this complex aquifer and the consistency of the different datasets. The Ploemeur site, which has been used for water supply at a rate of about 106 m3 per year since 1991, belongs to the French network of hydrogeological sites H+ and is currently used for monitoring groundwater changes and testing innovative field methods.
AGU Fall Meeting 2014
San Francisco, United States

insu-01088596
https://hal-insu.archives-ouvertes.fr/insu-01088596