Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We studied the deformation in a partially molten mantle through detailed petrostructural analysis of plagioclase lherzolites from the northwestern part of the central Lanzo massif. These peridotites display a pervasive anastomosed network of millimetre to centimetre-scale plagioclase-rich bands, which grades locally into a planar layering marked by an intercalation of plagioclase-rich and olivine-rich layers up to tens of centimetres wide. Both the anastomosed and the planar layering are subparallel to the deformation fabric, characterized by a foliation defined by the shape-preferred orientation of olivine and by crystal preferred orientation (CPO) of olivine, orthopyroxene, and clinopyroxene. This parallelism, the coexistence of microstructural evidence for melt-rock reactions and for deformation by dislocation creep, and the predominance of axial-[010] olivine CPO patterns, characterized by [010] axes clustered normal to the layering, indicate that deformation and the reactive melt percolation that formed the layering were coeval. Strong heterogeneity in mineral composition in the planar layering domains, with Fe-enrichment in olivine and spinel and highly variable Ti content in spinel in cm-scale plagioclase-rich bands, implies that the latter interacted with higher melt volumes. High Ti contents in pyroxenes and spinel in the anastomosed layering domains point to changes in melt composition, hinting to less effective melt transport. We propose therefore that the planar layering records melt segregation in layers parallel to the shear plane, whereas the anastomosed layering results from melt alignment along grain boundaries subparallel to the shear plane, without segregation. Finite strain in the different layers cannot be quantified, but comparison of the present observations with data from experiments and from other mantle outcrops displaying shear-controlled melt organization suggests that the transition from the anastomosed to the planar layering might record an increase in finite strain, that is, strain localization associated with variations in the instantaneous melt fraction.
ISSN: 0040-1951

hal-01053509
https://hal.archives-ouvertes.fr/hal-01053509
DOI : 10.1016/j.tecto.2014.01.007

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Melt generation in the continental crust is thought to significantly influence seismic bulk velocities and anisotropy, although existing laboratory data provide limited constraints on such seismic attributes. In this study we measured ultrasonic compressional wave speeds (Vp) and anisotropy during sample compaction, mica-breakdown and melt-generation in synthetic, foliated quartz–muscovite aggregates. Measurements were performed at peak conditions of 300 MPa hydrostatic confining pressure and 750 °C, over a six hour time period, for three separate samples where wave propagation directions were aligned at 0°, 45° and 90° with respect to the foliation plane. The experiments are initially marked by sample compaction and rapid reduction in porosity (from 25% to <2 vol%), with a corresponding increase in Vp. During initial stages of the experiment Vp ranges from 4.65 to 5.45 km/s, depending on the direction of the P wave propagation, resulting in up to ∼16% anisotropy, which originates mainly from the preferred orientation of muscovite and possible incipient melt lenses oriented parallel to foliation. As the experiment progresses the bulk Vp decreases gradually and Vp anisotropy drops from ∼16% to ∼2% after five hours into the experiment. The drop in anisotropy is caused by muscovite-breakdown and increasing amount of partial melting of the aggregate. The bulk velocities are considerably lower than predicted for a mixture of muscovite and β-quartz (stable at 300 MPa and 750 °C). Thermodynamic modeling indicates that mica breakdown and production of melt with ∼2 wt% dissolved water in the aggregate can explain the low Vp, even though β-quartz is stable; the modeled Vp is ∼4.75 km/s at 300 MPa and 750 °C. These ultrasonic attributes signify movement of the melt to fill vacant pores and coating grain boundaries, effectively connecting melt films and reducing seismic anisotropy. The results may apply to regions where crustal melting is on-going, in particular regions of elevated temperature that are only weakly deforming, with coupled anomalously low bulk velocities and seismic anisotropy.
ISSN: 0012-821X

hal-01243569
https://hal.archives-ouvertes.fr/hal-01243569
DOI : 10.1016/j.epsl.2015.05.039