Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Fault affecting silicoclastic sediments are commonly enriched in clay minerals. Clays are sensitive to fluid–rock interactions and deformation mechanisms; in this paper, they are used as proxy for fault activity and behavior. The present study focuses on clay mineral assemblages from the Point Vert normal fault zone located in the Annot sandstones, a Priabonian-Rupelian turbidite succession of the Alpine foredeep in SE France. In this area, the Annot sandstones were buried around 6–8 km below the front of Alpine nappes soon after their deposition and exhumed during the middle-late Miocene. The fault affects arkosic sandstone beds alternating with pelitic layers, and displays throw of about thirty meters. The fault core zone comprises intensely foliated sandstones bounding a corridor of gouge about 20 cm thick. The foliated sandstones display clay concentration along S–C structures characterized by dissolution of K-feldspar and their replacement by mica, associated with quartz pressure solution, intense microfracturation and quartz vein precipitation. The gouge is formed by a clayey matrix containing fragments of foliated sandstones and pelites. However, a detailed petrographical investigation suggests complex polyphase deformation processes. Optical and SEM observations show that the clay minerals fraction of all studied rocks (pelites and sandstones from the damage and core zones of the fault) is dominated by white micas and chlorite. These minerals have two different origins: detrital and newly-formed. Detrital micas are identified by their larger shape and their chemical composition with a lower Fe–Mg content than the newly-formed white micas. In the foliated sandstones, newly-formed white micas are concentrated along S–C structures or replace K-feldspar. Both types of newly formed micas display the same chemical composition confirmed microstructural observations suggesting that they formed in the same conditions. They have the following structural formulas: Na0.05 K0.86 (Al 1.77 Fe0.08 Mg0.15) (Si3.22 Al0.78) O10 (OH)2. They are enriched in Fe and Mg compared to the detrital micas. Newly-formed chlorites are associated with micas along the shear planes. According to microprobe analyses, they present the following structural formula: (Al1,48 Fe2,50 Mg1,84) (Si2,82 Al1,18) O10 (OH)8. All these data suggest that these clay minerals are synkinematic and registered the fault activity. In the gouge samples, illite and chlorite are the major clay minerals; smectite is locally present in some samples.In the foliated sandstones, Kubler Index (KI) ((001) XRD peak width at half height) data and thermodynamic calculations from synkinematic chlorite chemistry suggest that the main fault deformation occurred under temperatures around 220 °C (diagenesis to anchizone boundary). KI measured on pelites and sandstones from the hanging and footwall, display similar values coherent with the maximal burial temperature of the Annot sandstones in this area. The gouge samples have a higher KI index, which could be explained by a reactivation of the fault at lower temperatures during the exhumation of the Annot sandstones formation
ISSN: 0191-8141

hal-01172423
https://hal.archives-ouvertes.fr/hal-01172423
DOI : 10.1016/j.jsg.2015.03.012

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The interplay between fault zone cataclasis and cementation is important since both processes can drastically reduce the permeability of faults in porous sandstones. Yet the prediction of fault cementation in high-porosity sandstone reservoirs remains elusive. Nevertheless, this process has rarely been investigated in shallowly buried faults (<2 km; T°<80 °C) where its sealing capacity could be acquired early in the geological history of a reservoir. In this paper, the macro- and microscopic analysis of a fault zone in the porous Cenomanian quartz arenite sands of Provence (France) shows that silica diagenesis occurs in the most intensely-deformed cataclastic parts of the fault zone. This fault zone shows 19–48% of its total thickness occupied by low-porosity quartz-cemented cataclastic shear bands whose porosities range from 0 – ca. 5%. The analysis of the weathering profile around the fault zone reveals the presence of groundwater silcretes in the form of tabular, tightly silicified concretions cross-cut by the fault. Detailed transmitted light, cold-cathodoluminescence and scanning electron microscopy analyses of the silica cements (from the fault and the silcrete) reveal that all the silica cements originate from groundwater diagenetic processes. This study therefore shows that silica cementation can occur specifically in fault zones and as groundwater silcrete in the shallow context of a groundwater system, generated at the vicinity of an erosional unconformity.
ISSN: 0191-8141

hal-01278286
https://hal.archives-ouvertes.fr/hal-01278286
DOI : 10.1016/j.jsg.2015.10.001

Éditeur(s) : Gauthier-villars
Résumé : The aim of the joint French-British CYAPORC submersible cruise was the exploration and sampling of the Porcupine and Goban Escarpments. A paleozoic mesozoic sedimentary cover has been evidenced abov ea caledonian or older cristalline basement on the Porcupine scarp. On the Goban scarp, the observed outcrops are mainly lower Cretaceous carbonates overlying paleozoic sandstones
La campagne de plongée franco-britannique CYAPORC avait pour objet l'exploration et l'échantillonnage des escarpements de Porcupine et de Goban. Sur l'escarpement de Porcupine au Nord, on a mis en évidence, au-dessus d'un socle cristallin calédonien ou plus ancien, une couverture sédimentaire paléozoïque puis mésozoïque. Sur l'escarpement de Goban, les affleurements observés sont des séries du Crétacé inférieur reposantsur des niveaux de grès paléozoïques.
Comptes Rendus de l'Academie des Sciences Serie II (1251-8069) (Gauthier-villars), 1987-04 , Vol. 304 , N. 16 , P. 1003-1008

Droits : Académie des Sciences
http://archimer.ifremer.fr/doc/00184/29489/27853.pdf
http://archimer.ifremer.fr/doc/00184/29489/

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
We describe the structure, microstructure, and petrophysical properties of fault rocks from two normal fault zones formed in low-porosity turbiditic arkosic sandstones, in deep diagenesis conditions similar to those of deeply buried reservoirs. These fault rocks are characterized by a foliated fabric and quartz-calcite sealed veins, which formation resulted from the combination of the (1) pressure solution of quartz, (2) intense fracturing sealed by quartz and calcite cements, and (3) neoformation of synkinematic white micas derived from the alteration of feldspars and chlorite. Fluid inclusion microthermometry in quartz and calcite cements demonstrates fault activity at temperatures of 195degC to 268degC. Permeability measurements on plugs oriented parallel with the principal axes of the finite strain ellipsoid show that the Y axis (parallel with the foliation and veins) is the direction of highest permeability in the foliated sandstone (10-2 md for Y against 10-3 md for X, Z, and the protolith, measured at a confining pressure of 20 bars). Microstructural observations document the localization of the preferential fluid path between the phyllosilicate particles forming the foliation. Hence, the direction of highest permeability in these fault rocks would be parallel with the fault and subhorizontal, that is, perpendicular to the slickenlines representing the local slip direction on the fault surface. We suggest that a similar relationship between kinematic markers and fault rock permeability anisotropy may be found in other fault zone types (reverse or strike-slip) affecting feldspar-rich lithologies in deep diagenesis conditions.
ISSN: 0149-1423

hal-00903428
https://hal.archives-ouvertes.fr/hal-00903428
DOI : 10.1306/03071312127

Éditeur(s) : HAL CCSD
Résumé : The Restefond fault, located in the Late Eocene-Early Oligocene Alpine foreland basin, affects the well lithified and low porosity Grès d'Annot. The fault core zone is characterized by the occurrence of highly deformed sandstone lenses. Deformation inside the lenses corresponds to mm to sub-mm-spaced cleavage planes rich in phyllosilicates and up to cm-thick and dm-long quartz-calcite pure extensional veins. The cleavages are mostly composed of newly-formed synkinematic white mica and chlorite. By using thermodynamic thermometers based on the chemical composition of chlorite, a temperature of 200 ± 20 °C of fault activity was computed. This temperature shows that the Restefond fault was active at burial conditions comprised between 6.5 and 8 km, assuming a mean geothermal gradient between 25 and 30 °Ckm−1. The petrophysic properties of sandstones from the core zone and in the hanging and foot wall of the fault were determined on drilled plugs following three spacial directions. The permeability of the highly deformed sandstone from the core zone is about one order of magnitude higher than in the host rock. This increase in permeability occurs in the direction parallel to the S-C structures and is explained by the occurrence of well-connected micropores localized between platy phyllosilicates. This study shows that the fault petrophysic properties are mostly controlled by the precipitation of synkinematic phyllosilicates under deep burial conditions.
Swiss Journal of Geosciences

hal-00795551
https://hal.archives-ouvertes.fr/hal-00795551
DOI : 10.1007/s00015-012-0099-z

Résumé : This expedition was arranged on the initiative of Professor Erik Stensiö of Stockholm to collect fossil specimens for the British Museum (Natural History), the Palaeontologisk Museum, Oslo, and the Hiksmuseum , Stockholm. The chief object was to explore the Old Red Sandstone deposits in the geologically little known Wood Bay area and also in the neighbouring fjords on the north coast. The plans were given in The Polar Record, No. 18, and the final party, which was led by Professor E. A. Steusic with the support of A. Heintz of Oslo, consisted of E. Jarvik (Stockholm), G. Wangsjo (Uppsala), Sven Foyn and K. Aarhus (Oslo), X. Delle (Riga), E. I. White and W. N. Croft (London), J . A. Moy-Thomas (Oxford) and J. Brough (Manchester). C. Andreasen, a sealer from Tromso, brought the collecting party up to twelve. [NOT CONTROLLED OCR]

Droits : Scott Polar Research Institute, Cambridge, UK
http://archimer.ifremer.fr/doc/1940/publication-7341.pdf
http://archimer.ifremer.fr/doc/00000/7341/

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : Direct numerical simulations of flow through two millimeter-scale rock samples of limestone and sandstone are performed using three diverse fluid dynamic simulators. The resulting steady-state velocity fields are compared in terms of the associated empirical probability density functions (PDFs) and key statistics of the velocity fields. The pore space geometry of each sample is imaged at 5.06−μm voxel size resolution using X-ray microtomography. The samples offer contrasting characteristics in terms of total connected porosity (about 0.31 for the limestone and 0.07 for the sandstone) and are typical of several applications in hydrogeology and petroleum engineering. The three-dimensional fluid velocity fields within the explicit pore spaces are simulated using ANSYS® FLUENT® ANSYS Inc. (2009), EULAG Prusa et al. (Comput. Fluids 37, 1193–1207 2008), and SSTOKES Sarkar et al. (2002). These computational approaches are highly disperse in terms of algorithmic complexity, differ in terms of their governing equations, the adopted numerical methodologies, the enforcement of internal no-slip boundary conditions at the fluid-solid interface, and the computational mesh structure. As metrics of comparison to probe in a statistical sense the internal similarities/differences across sample populations of velocities obtained through the computational systems, we consider (i) integral quantities, such as the Darcy flux and (ii) main statistical moments of local velocity distributions including local correlations between velocity fields. Comparison of simulation results indicates that mutually consistent estimates of the state of flow are obtained in the analyzed samples of natural pore spaces despite the considerable differences associated with the three computational approaches. We note that in the higher porosity limestone sample, the structures of the velocity fields obtained using ANSYS FLUENT and EULAG are more alike than either compared against the results obtained using SSTOKES. In the low-porosity sample, the structures of the velocity fields obtained by EULAG and SSTOKES are more similar than either is to the fields obtained using ANSYS FLUENT. With respect to macroscopic quantities, ANSYS FLUENT and SSTOKES provide similar results in terms of the average vertical velocity for both of the complex microscale geometries considered, while EULAG tends to render the largest velocity values. The influence of the pore space structure on fluid velocity field characteristics is also discussed.
ISSN: 1420-0597

hal-01174152
https://hal.archives-ouvertes.fr/hal-01174152
DOI : 10.1007/s10596-015-9486-7

Éditeur(s) : Gauthier-Villars
Résumé : We report here our findings on the chemistry of methane, manganese and chloride dissolved in the interstitial water of the Barbados accretionary complex. The decollement separating the subduction plate from the accretionary wedge is geochemically characterized by high methane and manganese and low chloride concentrations relative to buried seawater. Sandstone layers occurring below the decollement and the compressive structures recording some of the earliest effects of offscraping are also characterized by similar anomalies. A fluid with the same characteristics is also found six kilometres to the east of the deformation front within the oceanic plate. High manganese concentration and low chlorinity also occur in the pore water of the offscraped sediment packages, but without associated anomalous methane concentrations. These results suggest that: Dewatering processes occur below the decollement in association with thermogenic methane production; Fluid with low chlorinity and high methane concentrations circulates mainly along the decollement, its propagation in the oceanic domain and along the main fracture zones being associated with these detachment surfaces; Diagenetic processes essentially control the dissolved manganese concentration and probably affect the methane content of the interstitial waters; The observations made in this paper illustrate advective processes in the front of an accretionary prism.
Oceanologica Acta (0399-1784) (Gauthier-Villars), 1991 , Vol. 14 , N. 1 , P. 33-49

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00101/21262/18873.pdf
http://archimer.ifremer.fr/doc/00101/21262/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Underground CO2 sequestration is highly recommended as an effective means of significantly decreasing CO2 concentration in the atmosphere. Mineral storage is the more secure technology, but requires the presence of high concentration of divalent cations in the pore-fluid. Results from CO2 percolation experiments through chlorite/zeolite-rich sandstone samples from the Pretty Hill Formation (Otway Basin, Australia) are presented. The dissolution of the laumontite (7 wt.%) and chamosite (7 wt.%) are the potential sources of calcium, iron and magnesium required for carbonate precipitation. The percolation experiment was setup to reproduce, at laboratory scale, the in situ temperature and pressure conditions (T = 95 degrees C and P = 10 MPa). The fluid injected at constant flow rate is a rock-equilibrated brine subsequently enriched in CO2 up to partial pressure of 6 MPa. We observe feldspars, laumontite and chamosite dissolution, kaolinite and silica precipitation and a noticeable sink of CO2 in the sample which is attributed to the precipitation of both amorphous carbon due to the reduction of CO2 and Fe-rich carbonate. Permeability decreases of about one order of magnitude due to the localization of the kaolinite precipitation in the main flow paths, while porosity increases. The high reactivity of this sandstone makes this reservoir a valuable target for CO2 mineralization, but the associated permeability decrease may limit the injection rate and the spreading of the CO2 in the reservoir.
ISSN: 0009-2541

hal-00712829
https://hal.archives-ouvertes.fr/hal-00712829
DOI : 10.1016/j.chemgeo.2011.11.018

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
Determination of the membrane seal capacity of deformation bands is critical for managing geologic reservoirs in porous sandstones. In this study, we have analyzed a cataclastic shear-band network developed in uncemented porous sandstone in Provence, France. Geometrical analyses of the bands show significant differences between three types of bands (single strand, multistrand, and band cluster), sorted by their number of strands, their amount of shear displacement, and their thicknesses. At the microscopic scale, the image-analysis porosities and the grain-size distributions allow definition of three different types of microstructural deformation: damage zone, protocataclastic, and cataclastic. Whereas damage zone and protocataclastic deformations are observed in each type of band, cataclastic strands are observed in clusters and, sometimes, in multistrands. Cataclastic strands are characterized by a porosity reduction of 10 to 25% and a permeability reduction of three to five orders of magnitude compared to the host rock. Field observations of iron hydroxide precipitations around the bands suggest that cataclastic strands were membrane seals to water flow under vadose condition. This study therefore highlights the importance of the degree of cataclasis in shear bands as membrane seals to subsurface fluid flows in sandstone reservoirs.
ISSN: 0149-1423

hal-00766557
https://hal.archives-ouvertes.fr/hal-00766557
DOI : 10.1306/04051211097

Éditeur(s) : HAL CCSD
Résumé : The DRADEM campaign was performed from July 9th to 21th 2016 on board the Pourquoi Pas?, in the Exclusive Economic Zones of Suriname and French Guyana. This campaign belongs to a program dedicated to geological investigations of the Demerara plateau, following the GUYAPLAC (2003) and IGUANES (2013) campaigns, and before the MARGATS campaign (2016). The aims of the DRADEM campaign were to map the continental slope of the transform margin north of the Demerara plateau, and to dredge the rocks outcropping in the slope.We completed the bathymetric mapping of the continental slope, including part of the edged of the Demerara plateau. These new bathymetric data confirm the segmentation of the transform margin in three parts with very different morphologies. In addition, two circular structures were interpreted as mud volcanoes, one on the northern edge of the plateau, the other one in the distal part of the Orinoco deep sea fan.Twelve dredges were performed between 4700 and 3500 m depths. Four from these twelve did not recovered rocks. The eight others brought back variables amounts of rocks, often encrusted, but of various natures: sediments (breccia, coarse sandstones, sandstones with plants debris, sandstones with shells, clayey ooze), micro-granular rocks and metamorphic rocks (including mylonite). The nature of the rocks was determined from macroscopic observation of the rocks, which are currently altered. Of course, these determinations need to be validated and specified by onshore further studies. Anyway, most of these rocks were previously unknown in this area, and they will strongly influence our understanding of the structure and evolution of this margin. They evidence huge vertical displacements that brought back to the surface some of these rocks that formed in a deep setting.
https://hal.archives-ouvertes.fr/hal-01418244

Droits : http://creativecommons.org/licenses/by-nc/
hal-01418244
https://hal.archives-ouvertes.fr/hal-01418244
https://hal.archives-ouvertes.fr/hal-01418244/document
https://hal.archives-ouvertes.fr/hal-01418244/file/DRADEM-Campaign%20Report.pdf

Éditeur(s) : HAL CCSD
Résumé : In order to minimize CO2 atmospheric concentration, a solution consists in sequestrating CO2 in geological reservoirs. To estimate long term risks, it is necessary to quantify the couplings between reaction processes as well as structural and hydrodynamical modifications. We realised two experimental benches enabling injecting CO2-enriched-brine in conditions corresponding to in situ storage (T < 200 oC and P < 200 bar) and developed
an experimental protocol using X-Ray microtomography and fluid and rock analyses in order to measure the variations of physical and chemical parameters.
The study of carbonated reservoirs near the injection well, allows quantifying different k-phi relationships depending on the dissolution processes and triggered by the local fluid chemical composition and initials conditions. Away from the injection well, we observe carbonate precipitation decreasing the permeability. The study of fracturated caprock samples shows that alternative percolation of CO2-enriched-brine and CO2 gas increases the fracture permeability.
The study of silicated rocks indicates carbonate precipitation in zeolite sandstone and sintered dunite grains. Nevertheless, in zeolite sandstone we also observe the precipitation of clay particles located in the uid pathways which decrease strongly the permeability.
Afin de minimiser la concentration en CO2 dans l'atmosphère une solution consiste à le séquestrer dans les réservoirs géologiques. Pour évaluer les risques à long terme, il est nécessaire de quantifier les couplages entre les processus réactionnels et les modifications structurales et hydrodynamiques. Dans cette optique, nous avons construit deux dispositifs expérimentaux permettant d'injecter des saumures chargées en CO2 dans les conditions de stockage (T < 200 °C et P < 200 bar) et mis en oeuvre un protocole expérimental utilisant la microtomographie RX et l'analyse des roches et des fuides pour quantifier les variations des paramètres physiques et chimiques. Dans le cas des réservoirs carbonatés, on observe, près du puits d'injection, une forte variabilité des relations k-phi en fonction du régime de dissolution contrôlé par la chimie locale du fluide, ainsi que par les conditions initiales. A plus grande distance, on observe des processus de précipitation diminuant fortement la perméabilité. L'étude des roches de couverture fracturées (argilite) a montré qu'une percolation alternée d'une saumure chargée en CO2 et de CO2 gaz augmentait la perméabilité de fracture. Dans le cas des roches silicatées, la précipitation de carbonates est mise en évidence aussi bien dans les grès à zéolites que dans les frittés de dunite de San Carlos. Cependant, dans les grès à zéolites, la précipitation d'une phase argileuse est observée dans les chemins d'écoulement et engendre une forte diminution de la perméabilité.
https://tel.archives-ouvertes.fr/tel-00416408

tel-00416408
https://tel.archives-ouvertes.fr/tel-00416408
https://tel.archives-ouvertes.fr/tel-00416408/document
https://tel.archives-ouvertes.fr/tel-00416408/file/These_Luquot.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Improving the prediction of sub-seismic structures and their petrophysical properties is essential for realistic characterization of deformed sandstone reservoirs. In the present paper, we describe permeability contrasts induced by cataclastic deformation bands and faults in porous sandstones (766 data synthesized from field examples and the literature). We also discuss the influence of several factors, including tectonic regime, presence of a fault, burial depth, host sandstone porosity, and grain size and sorting for their initiation and permeability. This analysis confirms that permeability decrease is as a function of grain-crushing intensity in bands. Permeability reduction ranges from very limited in crush-microbreccia of compaction bands to high permeability reduction in cataclasites and ultracataclasites of shear-dominated bands, band clusters and faults. Tectonic regime, and especially normal-fault regime, with its tendency to localize strain and generate faults, is identified as the most important factor, leading to the formation of cataclastic bands with high permeability contrasts. Moreover, moderate burial depth (1–3 km) favors cataclastic bands with high permeability contrasts with respect to the host sandstone. High porosity, coarse-grain size and good grain sorting can slightly amplify the permeability reductions recorded in bands.
ISSN: 0191-8141

hal-01218408
https://hal.archives-ouvertes.fr/hal-01218408
DOI : 10.1016/j.jsg.2015.03.013

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Contractional deformation of highly porous sandstones is poorly explored, as compared to extensional deformation of such sedimentary rocks. In this work we explore the highly porous Aztec Sandstone in the footwall to the Muddy Mountain thrust in SE Nevada, which contains several types of deformation bands in the Buffington tectonic window: 1) Distributed centimeter-thick shear-enhanced compaction bands (SECBs) and 2) rare pure compaction bands (PCBs) in the most porous parts of the sandstone, cut by 3) thin cataclastic shear-dominated bands (CSBs) with local slip surfaces. Geometric and kinematic analysis of the SECBs, the PCBs and most of the CSBs shows that they formed during ∼E–W (∼100) shortening, consistent with thrusting related to the Cretaceous to early Paleogene Sevier orogeny of the North American Cordilleran thrust system. Based on stress path modeling, we suggest that the compactional bands (PCBs and SECBs) formed during contraction at relatively shallow burial depths, before or at early stages of emplacement of the Muddy Mountains thrust sheet. The younger cataclastic shear bands (CSBs, category 3), also related to E–W Sevier thrusting, are thinner and show larger shear offsets and thus more intense cataclasis, consistent with the initiation of cataclastic shear bands in somewhat less porous materials. Observations made in this work support earlier suggestions that contraction lead to more distributed band populations than what is commonly found in the extensional regime, and that shear-enhanced compaction bands are widespread only where porosity (and permeability) is high.
ISSN: 0191-8141

hal-01171854
https://hal.archives-ouvertes.fr/hal-01171854
DOI : 10.1016/j.jsg.2015.02.014

Éditeur(s) : HAL CCSD
Résumé : This study is designed to improve the understanding of structural, mechanical and petrophysical characteristics of deformation bands in porous sandstone such as their potential influence on fluid storage or migration in reservoir setting. Structural and petrophysical analysis of band networks from Provence show that permeability of band is mainly controlled by the degree of cataclasis and diagenetic processes at depth. Map-scale analysis of band networks underlines the major influence of tectonic regime on band distribution, organization and permeability. Band associated to normal-fault regime (cataclasis and low-permeability) are located around map-sclae-fault whereas band associated to thurst-fault regime (moderate cataclasis and permeability) are pervasively distributed in all the area. Reverse-sense band are cataclastic and low-permeabiilty around the Roquemaure thrust, which show the potential role of large-scale fault on structural and petrophysical characteristics of bands. This analysis also shows the influence of fault propagation on formation of low permeability catacastic bands. This analysis suggests also granulometry as factor controlling organization of band networks.A mechanical analysis of deformation bands is realized based on results from Provence. Yield envelopes of these materials are calculated from analytical solution. Triaxial tests done on sandstone (L'Etang quarry, Orange) confirm the shape of yield envelope theoretically calculated. Triaxial tests done on the poorly-lithified sands (Boncavaï quarry, Uchaux) show grain size, sorting and packing influencing yield envelope and cataclastic band localization at shallow burial depth. Stress paths are calculated for burial and tectonic event (extension and contraction) using the relationship between main stress and secondary stresses (K0) calibrated from well data. These different results are integrated into a model which allows to estimate type and structural characteristics of bands susceptible to form for a known geological setting.A structural, mechanical and petrophysical model is established form these results. This model is calibrated by permeability data from deformation bands of Provence and results from the mechanical model of strain localization. This model is also confronted to a synthesis of permeability data from literature, which confirms the influence of the different controlling parameters integrated to the model. This model is applied for two sites of uranium exploration/exploitation in porous sandstone reservoirs and validated by field observations.
Cette étude est destinée à améliorer la compréhension des caractéristiques structurales, pétrophysiques et mécaniques des bandes de déformation dans les grès poreux ainsi que de leur rôle potentiel sur la migration ou le piégeage des fluides en milieu réservoir. L'analyse structurale et pétrophysique des réseaux de bandes de Provence montre que leur perméabilité découle principalement de l'intensité de la cataclase dans leur microstructure et des processus diagénétiques qui peuvent s'y localiser avec la profondeur. L'analyse régionale de ces réseaux de bandes souligne l'influence majeure du régime tectonique sur leur distribution, leur organisation et leur perméabilité. Les bandes associées au régime normal (cataclactiques et peu perméables) sont localisées autour des failles cartographiques, tandis que les bandes associées au régime inverse (modérement cataclastiques et perméables) sont distribuées dans toute la région. Les bandes inverses sont fortement cataclastiques et imperméables uniquement autour du chevauchement de Roquemaure ce qui montre le rôle potentiel de la présence de grande faille sur les caractéristiques structurales et pétrophysiques de ces bandes. D'autre part, cette analyse suggère que la granulométrie de l'encaissant peut influencer l'initiation et l'organisation des réseaux. L'analyse mécanique des bandes de déformation a ensuite été réalisée à partir des résultats obtenus en Provence. L'enveloppe de plasticité de ces matériaux est calculée à l'aide d'une solution analytique. Les essais triaxiaux menés sur le grès de la carrière de l'Etang (orange) confirment la forme de ces enveloppes estimées théoriquement. Les essais réalisés sur les sables de Boncavaï (Uchaux) montrent que la taille des grains, le tri et de la compaction dans ces matériaux peu lithifiés influent sur leurs enveloppes de plasticité et la localisation des bandes cataclastiques à faibles profondeurs. Les trajets de contraintes sont estimés pour les phases d'enfouissement et de chargement tectonique (extension et compression) à partir de la relation entre contrainte principale et contraintes secondaires (K0), calibrée à partir de données de forage. Ces résultats sont intégrés à un modèle permettant d'estimer la nature et les caractéristiques structurales des bandes susceptibles de se former dans un contexte géologique donné. Un modèle structural, mécanique et pétrophysique a été établir à partir de ces différents résultats. Ce modèle est calibré à partir des données de perméabilité mesurées sur les bandes de Provence et des résultats du modèle mécanique de localisation cité précédemment. Ce modèle a ensuite été confronté à une synthèse des données de perméabilité disponibles dans la littérature et confirme l'influence des différents paramètres de contrôle pris en compte dans le modèle. Ce modèle a enfin pu être appliqué sur deux sites d'explorations/exploitations d'uranium en réservoir gréseux poreux et validé par les résultats obtenus, en concordance avec les observations de terrain.
https://tel.archives-ouvertes.fr/tel-01001389

NNT : 2013MON20067
tel-01001389
https://tel.archives-ouvertes.fr/tel-01001389
https://tel.archives-ouvertes.fr/tel-01001389/document
https://tel.archives-ouvertes.fr/tel-01001389/file/36072_BALLAS_2013_archivage-1_cor.pdf

Résumé : The slides were taken on collecting trips sponsored by the William L. Bryant Foundation, where books, music and art indigenous to the regions were gathered. They are organized by geographical location.
Mount Hillaby, whose peak located in Scotland District of the Saint Andrew’s parish, is the highest elevation in Barbados at 340 meters (1115 feet) above sea level. Mount Hillaby, whose soil is composed of sandstone and chalk, is the summit of a mountain range that stretches from Trinidad to Puerto Rico. The Scotland District is the only location in the Caribbean where this mountain range is above water. This range is an example of an accretionary prism which is formed from sediments on the ocean floor pushing together at the junction of two tectonic plates. From Mount Hillaby’s peak viewers can see the beaches of Bathsheba and Chalky Mount, a range of hills with a jagged profile that contains clay deposits used by local potters. Slide labeled Barb 23.
Barbados -- Caribbean region -- Saint Andrew

Droits : All rights to images are held by the respective holding institution. This image is posted publicly for non-profit educational uses, excluding printed publication. For permission to reproduce images and/or for copyright information contact Special Collections & University Archives, University of Central Florida Libraries, Orlando, FL 32816 phone (407) 823-2576, email: speccoll@ucf.edu
CFM1972_01a
Sheet 20: 16
http://ufdc.ufl.edu/AA00017922/00001

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Field observations of highly porous and permeable sandstone in the Orange area (S-E Basin, France) show that networks of shear-enhanced compaction bands can form in a contractional regime at burial depths of about 400 m ± 100 m. These bands show equal compaction and shear displacements, are organized in conjugate and densely distributed networks, and are restricted to the coarse-grained (mean grain diameter of 0.6 ± 0.1 mm) and less porous (porosity of 26 ± 2%) sand layers. The bands are crush microbreccia with limited grain comminution and high grain microfracture density. They show reductions of permeability (mD) ranging from 0 to little more than 1 order of magnitude. They show no control on the alteration products related to meteoric water flow, which suggests that these shear-enhanced compaction bands have no or only negligible influence on subsurface fluid flow. Their selective occurrence and small (20%) reduction in transmissibility in densely populated layers prevented them from compartmentalizing the sandstone reservoirs. A comparison with compaction-band populations in the Navajo and Aztec sandtsones (western U.S.) emphasizes the role of burial depth and the presence of chemical compaction processes for the sealing potential of deformation bands.
ISSN: 0191-8141

hal-00807309
https://hal.archives-ouvertes.fr/hal-00807309
DOI : 10.1016/j.jsg.2012.11.008

Éditeur(s) : HAL CCSD Copernicus Publications
Résumé : International audience
During Ocean Drilling Program Leg 134, a mixed sequence of volcaniclastic and carbonate sediments was cored together with basaltic breccias and a single basalt sill in Hole 833B. In this study, data from Schlumberger's Geochemical Logging Tool, together with physical property logs, characterise part of the section and establish a complete log-derived lithostratigraphy. The major transition between the sedimentary rocks and a basaltic sill at 830 mbsf (metres below sea floor) is clearly seen as well as the distinction between the silicate-rich sediments and the carbonate-rich part of the section. The transition between the volcanic sandstone interbedded with basaltic and sed-lithic breccia of Unit III, and the volcanic sandstone of Unit IV is clearly marked by the physical property logs. The accuracy of the logging data was evaluated and discussed with an improved log versus core correlation. The cluster analysis of the complete data set shows a correlation with the data provided by the mechanical caliper device, which in turn indicates the quality of the borehole.
ISSN: 1816-8957

hal-00642165
http://hal.upmc.fr/hal-00642165
http://hal.upmc.fr/hal-00642165/document
http://hal.upmc.fr/hal-00642165/file/Rabaute_et_al-SciDrilling-1997.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Heletz sandstone (Israel) reactivity is studied by means of CO2-rich brine percolation experiments and modeling. Experiments are performed at in situ temperature and pressure conditions with two distinctly different injection flow rates and for two different brine compositions: the genuine Heletz brine and a similar brine but in equilibrium with gypsum. The Heletz sandstone is composed of quartz, dolomite, ankerite, K-feldspar, clay minerals and minor amounts of gypsum and pyrite. The main reaction is the dissolution of the carbonates which is fastest for the highest flow rate injection and for the genuine Heletz brine. Permeability increases during the five percolation experiments, regardless of flow rate and brine type. This increase in permeability is associated to a decrease in porosity during the gypsum-equilibrated brine experiments due to gypsum precipitation. The precipitation of secondary minerals (kaolinite, muscovite and smectite) is mainly controlled by the dissolution of K-feldspar and largest at low flow rate injection, indicating that these precipitation processes are diffusion-controlled and localized in immobile zones where favorable chemical micro-environments exist. These processes are quantified by means of a reactive transport model. These results indicated that the CO2 injection at the Heletz site should trigger both permeability increase in interface between brine and CO2, which may extend over a large extension and where mixing processes are very active, especially near the well under intermittent injection conditions.
ISSN: 1750-5836

hal-01356329
https://hal.archives-ouvertes.fr/hal-01356329
DOI : 10.1016/j.ijggc.2015.10.023

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The active collision zone around Taiwan orogen receives a variety of sedimentary inputs, including terrigenous flux from Taiwan and Chinese rivers, oceanic currents and atmospheric dust. In order to determine the present-day respective contributions of these different sources, we analysed the Pb and Sr isotopic compositions of late Quaternary sediments accumulated offshore east Taiwan. Samples from the Taiwan Coastal Range (andesites, sandstones, conglomerate and Peinan River terraces and suspended loads) have also been analysed to constrain the mean Taiwan isotopic signature. Mixing lines between the different sources of material indicate that the core located in the Okinawa Trough represents a mixture of about 60% of Taiwan, 30% of Chinese Loess and 10% of Yangtze River contributions. The southernmost core, located close to Luzon Are, is influenced by Taiwan (60%) and volcanic material (40%). The Sr and Pb isotopic compositions of samples cored in the Manila Trench and in the Huatung Basin are strongly influenced by the Taiwan signature, while the Ryukyu Trench core samples point to significant but variable contributions of Chinese Loess and Yangtze River. This work also reports Zn isotopic variations in the silicate fraction of these marine core samples. The overall variation in Zn isotopic compositions (expressed as 666 Zn) is greater than 0.3 per mil (parts per thousand) for an analytical precision of +/- 0.05 parts per thousand. The Zn isotopic signal for most of the marine core samples is similar to the literature data measured on sedimentary material, except for the Manila Trench core samples and the older sample from the Huatung Basin: they present values heavier by 0.2-0.3 parts per thousand, close to those obtained on all Taiwan rocks and Peinan River particulates. These results show: 1- the particular characteristics of Taiwan Zn isotopic compositions on a large scale; and: 2- the possible use of Zn isotopes as a tracer of material sources.
ISSN: 0009-2541

hal-00412214
https://hal.archives-ouvertes.fr/hal-00412214
DOI : 10.1016/j.chemgeo.2007.10.024