Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
We describe the structure, microstructure, and petrophysical properties of fault rocks from two normal fault zones formed in low-porosity turbiditic arkosic sandstones, in deep diagenesis conditions similar to those of deeply buried reservoirs. These fault rocks are characterized by a foliated fabric and quartz-calcite sealed veins, which formation resulted from the combination of the (1) pressure solution of quartz, (2) intense fracturing sealed by quartz and calcite cements, and (3) neoformation of synkinematic white micas derived from the alteration of feldspars and chlorite. Fluid inclusion microthermometry in quartz and calcite cements demonstrates fault activity at temperatures of 195degC to 268degC. Permeability measurements on plugs oriented parallel with the principal axes of the finite strain ellipsoid show that the Y axis (parallel with the foliation and veins) is the direction of highest permeability in the foliated sandstone (10-2 md for Y against 10-3 md for X, Z, and the protolith, measured at a confining pressure of 20 bars). Microstructural observations document the localization of the preferential fluid path between the phyllosilicate particles forming the foliation. Hence, the direction of highest permeability in these fault rocks would be parallel with the fault and subhorizontal, that is, perpendicular to the slickenlines representing the local slip direction on the fault surface. We suggest that a similar relationship between kinematic markers and fault rock permeability anisotropy may be found in other fault zone types (reverse or strike-slip) affecting feldspar-rich lithologies in deep diagenesis conditions.
ISSN: 0149-1423

hal-00903428
https://hal.archives-ouvertes.fr/hal-00903428
DOI : 10.1306/03071312127

Éditeur(s) : HAL CCSD E Schweizerbart Science Publishers
Résumé : International audience
Mass balance calculations have been performed through a comparison of published graphical and statistical approaches applied to two contrasted geological settings: (i) the development of a greenschist-facies ductile shear-zone that recorded a weak volume change but significant mass transfers, and (ii) the formation of exoskarns in metacarbonate xenoliths that recorded a large volume decrease related to huge mass transfers. The comparison of the four mass-balance approaches shows that, if uncertainties are ignored, (1) they yield similar results concerning the mobile vs immobile behaviour of many components; (2) they yield similar mass-change values on bulk rock and on individual chemical elements (bulk-rock mass-change values differ by a maximum of ca. 15 % between graphical and statistical treatments of the metacarbonate xenolith evolution). The main difference concerns the uncertainties on mass changes (for bulk rocks and individual elements), which are much larger with the graphical than with the statistical approaches when uncertainties on chemical elements are taken into account, as they should be.The main advantage of the graphical methods is their rapid implementation and the clarity of the diagrams. Their main disadvantages are that uncertainties on each chemical element and bulk compositions are not taken into account and the difficulty in choosing an accurate immobility field to precisely define errors. Graphical methods need to be completed by a statistical treatment that gives absolute mass transfer results. The statistical approaches have the advantage of taking into account the chemical heterogeneities of the compared populations, in conjunction to a precise data treatment. The statistical treatment is an important and necessary step to decipher and to be pertinent in interpreting mobility/immobility of chemical elements, and, thus, in the absolute quantification of mass and volume changes.
ISSN: 0935-1221

hal-01260258
https://hal.archives-ouvertes.fr/hal-01260258
DOI : 10.1127/ejm/2015/0027-2475

Éditeur(s) : HAL CCSD
Résumé : Thrusting fault zone in foreland basins are characterized by highly foliated zones generally enriched in phyllosilicates which can play a major role on the mechanical behaviour of the fault. In this context, investigations of synkinematic clay minerals permit to determine the origin of the fluid from which they precipitated as well as the mechanisms of deformation. Our study is focused on clay mineral assemblages (illite and chlorite) in a major thrust fault located in the Monte Perdido massif (southern Pyrenees), a shallow thrust that affects upper cretaceous-paleocene platform carbonates and lower Eocene marls and turbidites. It implied 3 km of displacement of the Monte Perdido thrust unit with respect to the underlying Gavarnie unit. In this area the cleavage development by pressure-solution is linked to the Monte Perdido and Gavarnie thrust activity. The core zone of the fault, about 6 m thick, consists of an interval of intensely deformed clay-bearing rocks bounded by major shear surfaces. The deformed sediment is markedly darker than the protolith. Calcite-quartz shear veins along the shear planes are abundant. Detailed SEM and TEM observations of highly deformed fault zone samples indicate that clay mineral enrichment in the core zone of the fault is not only related to passive increase by pressure-solution mechanism but that dissolution-recrystallization of phyllosilicates occurs during deformation. A mineral segregation is observed in the highly deformed zone. Newly formed 2M 1 muscovite is present along the cleavage whereas IIb chlorite crystals fill SV2 shear veins suggesting syntectonic growth of phyllosilicates in the presence of fluids in low-grade metamorphic conditions. These mineralogical reactions act as weakening processes and would favour Monte Perdido fault creeping.
Swiss Journal of Geosciences

hal-00795553
https://hal.archives-ouvertes.fr/hal-00795553
DOI : 10.1007/s00015-012-0098-0

Éditeur(s) : HAL CCSD
Résumé : International audience
Up-to-date estimates of the health outcomes of preterm children are needed for assessing perinatal care, informing parents, making decisions about care, and providing evidence for clinical guidelines. To determine survival and neonatal morbidity of infants born from 22 through 34 completed weeks' gestation in France in 2011 and compare these outcomes with a comparable cohort in 1997. The EPIPAGE-2 study is a national, prospective, population-based cohort study conducted in all maternity and neonatal units in France in 2011. A total of 2205 births (stillbirths and live births) and terminations of pregnancy at 22 through 26 weeks' gestation, 3257 at 27 through 31 weeks, and 1234 at 32 through 34 weeks were studied. Cohort data were collected from January 1 through December 31, 1997, and from March 28 through December 31, 2011. Analyses for 1997 were run for the entire year and then separately for April to December; the rates for survival and morbidities did not differ. Data are therefore presented for the whole year in 1997 and the 8-month and 6-month periods in 2011. Survival to discharge and survival without any of the following adverse outcomes: grade III or IV intraventricular hemorrhage, cystic periventricular leukomalacia, severe bronchopulmonary dysplasia, retinopathy of prematurity (stage 3 or higher), or necrotizing enterocolitis (stages 2-3). A total of 0.7% of infants born before 24 weeks' gestation survived to discharge: 31.2% of those born at 24 weeks, 59.1% at 25 weeks, and 75.3% at 26 weeks. Survival rates were 93.6% at 27 through 31 weeks and 98.9% at 32 through 34 weeks. Infants discharged home without severe neonatal morbidity represented 0% at 23 weeks, 11.6% at 24 weeks, 30.0% at 25 weeks, 47.5% at 26 weeks, 81.3% at 27 through 31 weeks, and 96.8% at 32 through 34 weeks. Compared with 1997, the proportion of infants surviving without severe morbidity in 2011 increased by 14.4% (P < .001) at 25 through 29 weeks and 6% (P < .001) at 30 through 31 weeks but did not change appreciably for those born at less than 25 weeks. The rates of antenatal corticosteroid use, induced preterm deliveries, cesarean deliveries, and surfactant use increased significantly in all gestational-age groups, except at 22 through 23 weeks. The substantial improvement in survival in France for newborns born at 25 through 31 weeks' gestation was accompanied by an important reduction in severe morbidity, but survival remained rare before 25 weeks. Although improvement in survival at extremely low gestational age may be possible, its effect on long-term outcomes requires further studies. The long-term results of the EPIPAGE-2 study will be informative in this regard.
ISSN: 2168-6211

hal-01258705
http://hal.univ-brest.fr/hal-01258705
PUBMED : 25621457
DOI : 10.1001/jamapediatrics.2014.3351

Éditeur(s) : HAL CCSD
Résumé : The Restefond fault, located in the Late Eocene-Early Oligocene Alpine foreland basin, affects the well lithified and low porosity Grès d'Annot. The fault core zone is characterized by the occurrence of highly deformed sandstone lenses. Deformation inside the lenses corresponds to mm to sub-mm-spaced cleavage planes rich in phyllosilicates and up to cm-thick and dm-long quartz-calcite pure extensional veins. The cleavages are mostly composed of newly-formed synkinematic white mica and chlorite. By using thermodynamic thermometers based on the chemical composition of chlorite, a temperature of 200 ± 20 °C of fault activity was computed. This temperature shows that the Restefond fault was active at burial conditions comprised between 6.5 and 8 km, assuming a mean geothermal gradient between 25 and 30 °Ckm−1. The petrophysic properties of sandstones from the core zone and in the hanging and foot wall of the fault were determined on drilled plugs following three spacial directions. The permeability of the highly deformed sandstone from the core zone is about one order of magnitude higher than in the host rock. This increase in permeability occurs in the direction parallel to the S-C structures and is explained by the occurrence of well-connected micropores localized between platy phyllosilicates. This study shows that the fault petrophysic properties are mostly controlled by the precipitation of synkinematic phyllosilicates under deep burial conditions.
Swiss Journal of Geosciences

hal-00795551
https://hal.archives-ouvertes.fr/hal-00795551
DOI : 10.1007/s00015-012-0099-z

Éditeur(s) : HAL CCSD
Résumé : International audience
European Clay Conference
Antalya, Turkey

hal-00671156
https://hal.archives-ouvertes.fr/hal-00671156

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : This study describes normal fault zones formed in foreland arkosic turbidites (the Grès d'Annot Formation, SW French Alps) under deep diagenesis conditions (~200 °C) and highlights the occurrence of two markedly different fault-rock types: (1) the foliated fault rocks of the Moutière-Restefond area; and (2) the dilatant fault rocks of the Estrop area. The deformation of (1) is dominated by intra- and transgranular fracturing, pressure solution of quartz and feldspar grains and syn-kinematic phyllosilicate precipitation resulting from feldspar alteration. The combination of these mechanisms results in a strongly anisotropic strain with intense shortening normal to the foliation (pressure solution) and extension parallel to the foliation (quartz- and calcite-sealed extension veins). This deformation implies local mass transfer that may be achieved without (or with limited) volume change. The deformation of (2) is expressed as dilatant quartz-sealed veins and breccia textures in which the main mechanisms are transgranular fracturing and quartz precipitation. Type (2) implies fault volume increase, isotropy of deformation and mass transfer at distances larger than in type (1). This study discusses the origins of (1) and (2) and shows that the permeability of (1) is anisotropic, with higher values than the host rocks parallel to the Y main deformation axis (i.e. perpendicular to the slip vector), whereas the permeability of (2) is isotropic and equivalent to that of the host rocks.
ISSN: 0954-4879

hal-01115177
https://hal.archives-ouvertes.fr/hal-01115177
DOI : 10.1111/ter.12100

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Phyllosilicate content and related permeability of fault zones form primary controls on hydraulic and mechanical behavior of the brittle crust. Hence, understanding and predicting the localization of these ubiquitous minerals is a major issue for fundamental and applied geosciences. We describe normal fault zones cutting a foreland arkosic turbiditic formation suffering high-T diagenesis and formed under conditions (~200°C) typical of deeply buried reservoirs and common within the seismogenic interval. Microstructural analyses show a large proportion of phyllosilicates (up to 34%) in the fault rock, derived from near-complete feldspar alteration and disaggregation during deformation. This study shows that even faults with offsets (~20 cm) much lower than bed thickness can have such large feldspar-to-phyllosilicate transformation ratios, implying that the origin of the phyllosilicates is purely transformation related. These results imply that the potential sealing capacity and strength of faults could be predicted from the host rock feldspar content. Where sealing capacity and fault strength can be related to phyllosilicate content, these properties can then also be inferred from the predicted phyllosilicate content: this opens up new horizons concerning the hydraulic and the mechanical behavior of the upper crust.
ISSN: 0094-8276

hal-00903574
https://hal.archives-ouvertes.fr/hal-00903574
DOI : 10.1002/grl.50829

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Field observations of highly porous and permeable sandstone in the Orange area (S-E Basin, France) show that networks of shear-enhanced compaction bands can form in a contractional regime at burial depths of about 400 m ± 100 m. These bands show equal compaction and shear displacements, are organized in conjugate and densely distributed networks, and are restricted to the coarse-grained (mean grain diameter of 0.6 ± 0.1 mm) and less porous (porosity of 26 ± 2%) sand layers. The bands are crush microbreccia with limited grain comminution and high grain microfracture density. They show reductions of permeability (mD) ranging from 0 to little more than 1 order of magnitude. They show no control on the alteration products related to meteoric water flow, which suggests that these shear-enhanced compaction bands have no or only negligible influence on subsurface fluid flow. Their selective occurrence and small (20%) reduction in transmissibility in densely populated layers prevented them from compartmentalizing the sandstone reservoirs. A comparison with compaction-band populations in the Navajo and Aztec sandtsones (western U.S.) emphasizes the role of burial depth and the presence of chemical compaction processes for the sealing potential of deformation bands.
ISSN: 0191-8141

hal-00807309
https://hal.archives-ouvertes.fr/hal-00807309
DOI : 10.1016/j.jsg.2012.11.008

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
From outcrops located in Provence (South-East France), we describe the distribution, the microstructures, and the petrophysical properties of deformation band networks related to both contractional and extensional tectonic events. In contraction, pervasively distributed networks of reverse-sense compactional shear bands are observed in all folded sand units of the foreland, whereas localized networks of clustered reverse-sense shear bands are only observed close to a large-scale thrust. In extensional setting, networks of clustered normal-sense shear bands are generally observed adjacent to map-scale faults (100 m–10 km scale), although some randomly distributed bands are also observed between these faults. Normal-sense cataclastic faults, i.e. zone of deformation bands containing a localized slip-surface, are also observed to be restricted to sand units, suggesting that faults initiated in the sands during extension, but not during contraction. Shear bands and faults show cataclastic microstructures with high-permeability reduction whereas compactional shear bands show crush microbreccia or protocataclastic microstructures with moderate permeability reduction. This basin-scale analysis underlines the major role of tectonic settings (thrust-fault versus normal-fault andersonian-stress regime) and the influence of inherited large-scale faults on the formation/localization of low-permeability shear bands. We also provide a geometrical analysis of the band network properties (spacing, thickness, shear/compaction ratio, degree of cataclasis, petrophysical properties) with respect to the median grain size, porosity and grain sorting of host sand. This analysis suggests that grain size, although less important than stress-state conditions and the presence of large-scale faults, has a non-negligible effect on band network geometry. No correlations are observed between the grain sorting, porosity and band network geometry.
ISSN: 0264-8172

hal-01116421
https://hal.archives-ouvertes.fr/hal-01116421
DOI : 10.1016/j.marpetgeo.2013.12.020

Éditeur(s) : HAL CCSD American Association of Petroleum Geologists
Résumé : International audience
Determination of the membrane seal capacity of deformation bands is critical for managing geologic reservoirs in porous sandstones. In this study, we have analyzed a cataclastic shear-band network developed in uncemented porous sandstone in Provence, France. Geometrical analyses of the bands show significant differences between three types of bands (single strand, multistrand, and band cluster), sorted by their number of strands, their amount of shear displacement, and their thicknesses. At the microscopic scale, the image-analysis porosities and the grain-size distributions allow definition of three different types of microstructural deformation: damage zone, protocataclastic, and cataclastic. Whereas damage zone and protocataclastic deformations are observed in each type of band, cataclastic strands are observed in clusters and, sometimes, in multistrands. Cataclastic strands are characterized by a porosity reduction of 10 to 25% and a permeability reduction of three to five orders of magnitude compared to the host rock. Field observations of iron hydroxide precipitations around the bands suggest that cataclastic strands were membrane seals to water flow under vadose condition. This study therefore highlights the importance of the degree of cataclasis in shear bands as membrane seals to subsurface fluid flows in sandstone reservoirs.
ISSN: 0149-1423

hal-00766557
https://hal.archives-ouvertes.fr/hal-00766557
DOI : 10.1306/04051211097

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In fold-and-thrust belts, shortening is mainly accommodated by thrust faults which are preferential zones for recrystallisation and mass transfer. This study focuses on a detachment fault related to the emplacement of the Monte Perdido thrust unit in the southern Pyrenees. The studied fault zone consists of a 10 m thick intensively foliated phyllonite developed within the Millaris marls, of Eocene age. The lithological homogeneity of the hanging wall and footwall allows us to compare the Millaris marls outside the fault zone with the highly deformed marls located in the fault zone and to quantify the chemical, mineralogical and volumetric changes related to deformation processes along the fault. The Millaris marls are composed of detrital quartz, illite, chlorite, minor albite and pyrite, in a micritic calcite matrix. In the fault zone, the cleavage planes are marked by clay minerals and calcite ± chlorite veins attest to fluid-mineral interactions during deformation. The mineral proportions in all samples from both the fault zone and Millaris marls have been quantified by two methods: (1) X-ray diffraction and Rietveld refinement, and (2) bulk chemical analyses as well as microprobe analyses to calculate modal composition. The excellent agreement between the results of these two methods allows us to estimate mineralogical variations using a modification of the Gresens' equation. During fault activation, up to 45 wt% of calcite was lost while the amounts of quartz and chlorite remained unchanged. Illite content remained constant to slightly enriched. The mineralogical variations were coupled with a significant volume loss (up to 45%) mostly due to the dissolution of micritic calcite grains. Deformation was accompanied by pressure solution and phyllosilicates recrystallisation. These processes accommodated slip along the fault. They required fluids as catalyst, but they did not necessitate major chemical transfers.
ISSN: 0264-8172

hal-00976361
https://hal.archives-ouvertes.fr/hal-00976361
DOI : 10.1016/j.marpetgeo.2013.12.016

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Fault affecting silicoclastic sediments are commonly enriched in clay minerals. Clays are sensitive to fluid–rock interactions and deformation mechanisms; in this paper, they are used as proxy for fault activity and behavior. The present study focuses on clay mineral assemblages from the Point Vert normal fault zone located in the Annot sandstones, a Priabonian-Rupelian turbidite succession of the Alpine foredeep in SE France. In this area, the Annot sandstones were buried around 6–8 km below the front of Alpine nappes soon after their deposition and exhumed during the middle-late Miocene. The fault affects arkosic sandstone beds alternating with pelitic layers, and displays throw of about thirty meters. The fault core zone comprises intensely foliated sandstones bounding a corridor of gouge about 20 cm thick. The foliated sandstones display clay concentration along S–C structures characterized by dissolution of K-feldspar and their replacement by mica, associated with quartz pressure solution, intense microfracturation and quartz vein precipitation. The gouge is formed by a clayey matrix containing fragments of foliated sandstones and pelites. However, a detailed petrographical investigation suggests complex polyphase deformation processes. Optical and SEM observations show that the clay minerals fraction of all studied rocks (pelites and sandstones from the damage and core zones of the fault) is dominated by white micas and chlorite. These minerals have two different origins: detrital and newly-formed. Detrital micas are identified by their larger shape and their chemical composition with a lower Fe–Mg content than the newly-formed white micas. In the foliated sandstones, newly-formed white micas are concentrated along S–C structures or replace K-feldspar. Both types of newly formed micas display the same chemical composition confirmed microstructural observations suggesting that they formed in the same conditions. They have the following structural formulas: Na0.05 K0.86 (Al 1.77 Fe0.08 Mg0.15) (Si3.22 Al0.78) O10 (OH)2. They are enriched in Fe and Mg compared to the detrital micas. Newly-formed chlorites are associated with micas along the shear planes. According to microprobe analyses, they present the following structural formula: (Al1,48 Fe2,50 Mg1,84) (Si2,82 Al1,18) O10 (OH)8. All these data suggest that these clay minerals are synkinematic and registered the fault activity. In the gouge samples, illite and chlorite are the major clay minerals; smectite is locally present in some samples.In the foliated sandstones, Kubler Index (KI) ((001) XRD peak width at half height) data and thermodynamic calculations from synkinematic chlorite chemistry suggest that the main fault deformation occurred under temperatures around 220 °C (diagenesis to anchizone boundary). KI measured on pelites and sandstones from the hanging and footwall, display similar values coherent with the maximal burial temperature of the Annot sandstones in this area. The gouge samples have a higher KI index, which could be explained by a reactivation of the fault at lower temperatures during the exhumation of the Annot sandstones formation
ISSN: 0191-8141

hal-01172423
https://hal.archives-ouvertes.fr/hal-01172423
DOI : 10.1016/j.jsg.2015.03.012