Éditeur(s) : Elsevier
Résumé : Regardless of the degree of closure of a recirculation system, effluents are produced and replacement water is needed, which limits the possibility of locating a seawater production system away from the shoreline. At the Palavas Ifremer station, in the south of France, a High Rate Algal Pond (HRAP) was operated during several years to treat the effluent from a recirculating aquaculture system before reusing it. The effect of the HRAP-treated water on the recirculation system and on the fish was investigated and the optimal algae growing conditions were defined. The experiments were carried out in three rearing systems: one flow through, one recirculating and one recirculating with a HRAP. The water flow rate, temperature, pH and salinity conditions were similar in all systems. The effect of reusing the HRAP-treated water is very limited (1) on the functioning of the recirculation system and (2) on fish performance, but it allows a significant reduction of the dissolved inorganic nitrogen and phosphorus concentration in the rearing water. HRAP treatment reduced metal accumulation in muscle and liver of RAS fish, except for chromium and arsenic. All biomarkers presented no significant difference between systems, except for Superoxide Dismutase (SOD) and EROD, which showed a higher concentration in RAS and in both recirculating system respectively. (c) 2005 Elsevier B.V. All rights reserved.
Aquaculture (0044-8486) (Elsevier), 2006-03 , Vol. 252 , N. 1 , P. 92-101

Droits : 2005 Elsevier
http://archimer.ifremer.fr/doc/2006/publication-2306.pdf
DOI:10.1016/j.aquaculture.2005.11.053
http://archimer.ifremer.fr/doc/00000/2306/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A set of four reactive flow-through experiments at temperature T = 100 degrees C and total pressure P=12 MPa was performed in limestone reservoir samples. By using various ranging from 0.7 to 10 MPa, these experiments mimic mass transfers occurring (1) near the injection well, where the brine is almost saturated with CO2 (i.e. P-CO2 approximate to P), and (2) at increasing distances from the injection well, where the fluid displays lower values and higher divalent cation concentrations due rock dissolution along the fluid pathway. Results for P-CO2 = 10 MPa show non-uniform dissolution features associated with transport-controlled mass transfer, while reaction-controlled uniform dissolution is observed for P-CO2 = 2.5 MPa. The experiment with P-CO2 = 6 MPa allows investigating in detail the transition from transport-to reaction-controlled dissolution. Conversely, the experiment reproducing conditions far from the injection well (P-CO2 = 0.7 MPa), shows a decrease of porosity triggered by the precipitation of Mg-rich calcite. For all the dissolution experiments, the time-resolved porosity phi(t) can be modeled by a simple non-linear equation including parameters that characterise the dissolution regime triggered by the reactivity of the inlet fluid (measured by the Damkohler number, Da). Furthermore, all dissolution experiments display power scaling between permeability (k) and porosity (phi) with distinctly different scaling exponents characterising the reactivity of the fluid percolating the sample, independently from the decrease with time of the reactive surface area. It is shown also that dissolution at moderate positive values of Da seems the most efficient to increase permeability and promote a rapid spreading of the reaction front, while inducing minimal modification of the porosity in the vicinity of the CO2 injection well. These results can be used to parameterize the k-phi function for modeling the earliest dissolution processes occurring in the vicinity of the reaction front.
ISSN: 0009-2541

hal-00445277
https://hal.archives-ouvertes.fr/hal-00445277
DOI : 10.1016/j.chemgeo.2009.03.028

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
To test the impact of fluid flow on the reactivity of porous (ultra-)mafic rocks, reactive percolation experiments were realized during which CO2-enriched water was injected at two different injection rates (Q = 0.1 and 1 mL h−1) through sintered analogues of olivine-accumulation zones in basaltic flows at temperature and fluid composition conditions (T = 180 °C; NaHCO3 buffered solution) favorable for CO2-mineralization (carbonation).All experiments resulted in silicate dissolution, carbonate precipitation upstream and (proto-)serpentine formation downstream indicating a decrease in the fluid reactivity along flow paths. The measured bulk carbonation rates ranged from 4 to 7 × 10−8 s−1; these values were significantly lower than previously published values of olivine carbonation rate obtained on powders in closed batch and flow-through reactors. Our study show complex couplings, at pore scale, between fluid flow, localization of reaction zones, and chemical reaction kinetics which in turn control hydrodynamic properties, carbonation rate and efficiency and fluid reactivity. This results in carbonation rates being higher when injection rates are high and permeability ultimately controlling carbonation reactions by limiting fluid input. During experiments, notable changes in permeability occurred for only minor changes in porosity indicating a control by the geometry of the porous network: heterogeneities in the distribution of flow paths favored the localization of precipitated minerals which in turn resulted in the closure of flow paths. This mechanism was particularly efficient at low injection rates. These results imply that controlling the injection rate could allow enhancing/limiting the efficiency of in situ carbonation.
ISSN: 0883-2927

hal-01115284
https://hal.archives-ouvertes.fr/hal-01115284
DOI : 10.1016/j.apgeochem.2014.11.024

Éditeur(s) : HAL CCSD Elsevier
Résumé : Deficient sealing in the well cement plugs and annulus due to mechanical fracturing is an important risk of CO2 leakage from the reservoir to others permeable layers and the surface. Such situation was reproduced at laboratory scale in order to determine the hydro-chemical control on the fracture permeability. Specifically, we investigated the effect of CO2 rich-brine flowing through fractured Portland cements at T = 60 °C and P = 10 MPa and variable flow rates. We showed that carbonation process is dominant and induces permeability decrease and leakage mitigation for extremely low flow rate whereas for high flow rate injection the permeability remains constant due to the precipitation of a low density secondary Si-rich phase which maintains the initial fracture aperture. At intermediate flow rate the hydraulic aperture can increase due to the densification of the material triggered by the net precipitation of low porosity calcite. These results emphasize that more complex behaviors than those considered from batch experiments may take place in the vicinity of flowing fractures. Specifically, the redissolution of the neoformed calcite as well as the development of amorphous phases, both controlled by the CO2-rich brine renewing rate in the fracture may prevent the healing fracture.
ISSN: 1750-5836

hal-00857555
https://hal.archives-ouvertes.fr/hal-00857555
DOI : 10.1016/j.ijggc.2013.04.002

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : Results are reported for an acidic water flow-through experiment conducted in a fractured argillaceous limestone sample (73% carbonates). The change in fracture geometry and related parameters is reported for six data sets obtained from synchrotron X-ray microtomography experiments. High-resolution three-dimensional images of the sample allowed quantification of the changes in fracture morphology at a spatial resolution of 6 ;μm. Mineral mass loss and permeability changes in the sample were also determined. Several physico-chemical phenomena were identified during the experiment. Initial smooth fracture surfaces evolved rapidly toward rough surfaces with uneven clay coverage due to the preferential dissolution of carbonate minerals compared to clay minerals whose dissolution rate is about 106 slower. A microporous clay coating progressively developed at the fluid-rock interface during heterogeneous dissolution of the fracture, while the global dissolution rate of the fracture walls exponentially decreased. The increase in surface roughness and the presumed reorganization of clays caused a progressive reduction in permeability. During the last flow-through stage, a large decrease in sample permeability was attributed to the large removal of clay particles; this process was responsible for a dramatic collapse of the fracture walls near the sample inlet and led to the development of preferential flow pathways. The development of the clay coating also acted as a barrier to flow and mass transfer between calcite grains and bulk solution and affected transport processes within the fracture
ISSN: 0043-1397

hal-00405333
https://hal.archives-ouvertes.fr/hal-00405333
DOI : 10.1029/2006WR005379

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Heletz sandstone (Israel) reactivity is studied by means of CO2-rich brine percolation experiments and modeling. Experiments are performed at in situ temperature and pressure conditions with two distinctly different injection flow rates and for two different brine compositions: the genuine Heletz brine and a similar brine but in equilibrium with gypsum. The Heletz sandstone is composed of quartz, dolomite, ankerite, K-feldspar, clay minerals and minor amounts of gypsum and pyrite. The main reaction is the dissolution of the carbonates which is fastest for the highest flow rate injection and for the genuine Heletz brine. Permeability increases during the five percolation experiments, regardless of flow rate and brine type. This increase in permeability is associated to a decrease in porosity during the gypsum-equilibrated brine experiments due to gypsum precipitation. The precipitation of secondary minerals (kaolinite, muscovite and smectite) is mainly controlled by the dissolution of K-feldspar and largest at low flow rate injection, indicating that these precipitation processes are diffusion-controlled and localized in immobile zones where favorable chemical micro-environments exist. These processes are quantified by means of a reactive transport model. These results indicated that the CO2 injection at the Heletz site should trigger both permeability increase in interface between brine and CO2, which may extend over a large extension and where mixing processes are very active, especially near the well under intermittent injection conditions.
ISSN: 1750-5836

hal-01356329
https://hal.archives-ouvertes.fr/hal-01356329
DOI : 10.1016/j.ijggc.2015.10.023

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Underground CO2 sequestration is highly recommended as an effective means of significantly decreasing CO2 concentration in the atmosphere. Mineral storage is the more secure technology, but requires the presence of high concentration of divalent cations in the pore-fluid. Results from CO2 percolation experiments through chlorite/zeolite-rich sandstone samples from the Pretty Hill Formation (Otway Basin, Australia) are presented. The dissolution of the laumontite (7 wt.%) and chamosite (7 wt.%) are the potential sources of calcium, iron and magnesium required for carbonate precipitation. The percolation experiment was setup to reproduce, at laboratory scale, the in situ temperature and pressure conditions (T = 95 degrees C and P = 10 MPa). The fluid injected at constant flow rate is a rock-equilibrated brine subsequently enriched in CO2 up to partial pressure of 6 MPa. We observe feldspars, laumontite and chamosite dissolution, kaolinite and silica precipitation and a noticeable sink of CO2 in the sample which is attributed to the precipitation of both amorphous carbon due to the reduction of CO2 and Fe-rich carbonate. Permeability decreases of about one order of magnitude due to the localization of the kaolinite precipitation in the main flow paths, while porosity increases. The high reactivity of this sandstone makes this reservoir a valuable target for CO2 mineralization, but the associated permeability decrease may limit the injection rate and the spreading of the CO2 in the reservoir.
ISSN: 0009-2541

hal-00712829
https://hal.archives-ouvertes.fr/hal-00712829
DOI : 10.1016/j.chemgeo.2011.11.018

Éditeur(s) : HAL CCSD
Résumé : Geological storage of CO2 is one of diverse technologies being explored to reduce atmospheric carbon fromindustrial processes (i.e. fossil fuel combustion). One of the specific features of CO2 injection is the possibility ofgeochemical reactions (dissolution – precipitation) between mobile reactive brine (e.g. formation water enrichedin CO2) and the host rock during the spatial and temporal evolution of CO2. That leads to modifications in thepore structure, which in turn change the flow dynamics of the reservoir (e.g. the permeability k). Then, thesesstructural modifications can largely control the injectivity, so that the pressure field in the reservoir and also theCO2 propagation. Accordingly, it is crucial to explore the changes in the reservoir properties (e.g. structural andhydrodynamic) induced during a CO2 injection and specially the relationships between them (e.g. k or reactivesurface-Sr versus porosity-φ , k versus rock heterogeneity), for developing predictive modelling tools of thetransport and reaction processes occurring during a CO2 injection and reliable risk assessment. In the case ofcarbonate rocks, the application of the predictive models of transport and reaction is still challenging, because oftheir high heterogeneity so that the incertitude in the reaction kinetics of carbonate minerals.From this perspective, we realized brine-enriched in CO2 percolation experiments through carbonate rocksamples in thermodynamic conditions expected during CO2 injection in deep reservoirs (T = 100°C et P =12MPa). The permeability changes k(t) is monitored during the experiments and the porosity variationφ (t) iscalculated from chemical analyses of the sampled outlet fluids, using ICP-EAS. The pore structure modificationsare investigated from high resolution X ray micro tomography images acquired from the synchrotron ofGrenoble (ESRF). Depending to the dissolution regime, controlled by the reservoir rock fabric and the chemicalcomposition of the brine (e.g. PCO2), we observed that a modification of pore structure can either improve(atypical result in dissolution context) or impair the value of the permeability k.
Le stockage géologique du CO2 est l’une des diverses technologies étant explorées afin deréduire les émissions de carbone atmosphérique des processus industriels (i.e. combustion del’énergie fossile). L’une des spécifiques caractéristiques de l’injection du CO2 en profondeurreste la possibilité de réactions géochimiques (dissolution-précipitation) entre la saumureréactive mobile (e.g. eau de formation enrichie en CO2) et la roche encaissante durantl’évolution spatiale et temporelle du CO2, conduisant à des modifications dans la structure despores et par conséquent dans les propriétés d’écoulement du réservoir (e.g. la perméabilité k).Donc, ces changements structuraux peuvent largement contrôler l’injectivité, ainsi que lechamp de pression dans le réservoir et aussi la propagation du CO2. Il demeure ainsi cruciald’explorer les changement dans les propriétés de réservoirs (e.g. structurales ethydrodynamiques) induits durant une injection de CO2 et explicitement les relations existantesentre eux (e.g. k ou surface réactive-Sr versus porosité-φ , k versus hétérogénéité de la roche),afin de développer des outils de modélisation prédictive des processus de transport etréactionnels se produisant durant une injection de CO2 et d’évaluer de façon fiable les risques.Dans le cas des réservoirs carbonatés, l’application des modèles prédictifs de transport réactifdemeure toujours un enjeu, car contrainte par la forte hétérogénéité en leur sein ainsi que parl’incertitude dans la cinétique de réactions des minéraux carbonatés dans ce contexte. Danscette optique, nous avons réalisé des expériences de percolation à travers des échantillons deroches carbonatées dans les conditions thermodynamiques de stockage en profondeur (T =100°C et P =12 MPa). L’évolution de la perméabilité k(t) est suivie au cours desexpériences ; et la variation de la porosité φ (t) est calculée à partir des résultats d’analyseschimiques au ICP-AES des fluides de sortie échantillonnés. L’investigation des modificationsapportées à la structure des pores est réalisée par le biais de la Micro-Tomographie hauterésolution à rayon X, acquise au synchrotron de Grenoble (e.g. ESRF).Dépendant du régime de dissolution, contrôlé par la fabrique de la roche réservoir et lacomposition chimique de la saumuré chargée en CO2 (e.g. PCO2 engagée), on a observéqu’une modification de la structure de la roche peut soit améliorer soit détériorer (résultatatypique en contexte de dissolution) la valeur de la perméabilité k.
https://hal.archives-ouvertes.fr/tel-01142136

tel-01142136
https://hal.archives-ouvertes.fr/tel-01142136
https://hal.archives-ouvertes.fr/tel-01142136/document
https://hal.archives-ouvertes.fr/tel-01142136/file/thesemangane2013.pdf

Éditeur(s) : Edp Sciences S A
Résumé : Reared sea bass were submitted to six stressful situations: hyperoxia with or without hypercapnia, increased stocking density in an open flow or recirculating system, transfer to another tank and nodavirus injection. The potentially negative impact of these factors on the lives of sea bass was investigated by measuring 9 water parameters and 19 fish parameters including total serum protein (TSP). TSP has already been used to evaluate stress. The present study investigates data of previous and new experiments, concentrating on the potential use of TSP as a routine indicator to assess welfare in sea bass reared on fish farms. In the current experiment, oxygen and carbon dioxide were seen to affect levels of TSP, but alterations were too erratic to enable proper comparison, probably because they are normal components of the fish environment and become toxic only by dose increase. TSP decreased when stocking density increased. After transfer to another tank, TSP decreased to 14% for three weeks and then increased during the fourth week through compensative overproduction, before returning to normal levels after 2 months. The results confirmed that transfer is an important stress factor for fish, with cumulative effects for successive transfers. TSP alteration of nodavirus-injected fish depends on the type of symptoms, which can be divided into 3 groups: (i) dying fish, in which TSP increased sharply due to over-production of protein involved in non-specific defences and inflammation, then decreased dramatically before death; (ii) whirling fish, a group that included both fish that later died, in which TSP decreased, and fish that subsequently survived, in which TSP increased due to development of specific immunity; and (iii) asymptomatic fish, in which TPS was similar to control levels and which were probably insensitive to nodavirus and/or had developed defences. In this paper, different mechanisms of TSP alteration are proposed and the interest of TSP as a field parameter is discussed. TSP is a non-destructive parameter that is robust, easy to measure everywhere and cheap, representing a suitable way of monitoring the overall welfare of fish by its regular increase. It can be used only as a "warning" of poor rearing conditions, however, and further investigations would be needed to identify the specific stress or health disorder.
Aquatic Living Resources (0990-7440) (Edp Sciences S A), 2011-04 , Vol. 24 , N. 2 , P. 121-127

Droits : EDP Sciences, IFREMER, IRD 2011
http://archimer.ifremer.fr/doc/00043/15382/12740.pdf
DOI:10.1051/alr/2011130
http://archimer.ifremer.fr/doc/00043/15382/

Éditeur(s) : HAL CCSD
Résumé : The Earth's magnetic field shows a large range of temporal variations from the year to several million years. I studied during my PhD thesis several aspects of these fluctuations, from recent secular variations to reversals. The first part of my manuscript deals with archeomagnetism, a discipline that allows to track the temporal variations of the Earth's magnetic field through millennia, mainly from archeological materials. I studied two sets of samples , one from Greece (Neolithic period 6800-3200 B.C.) and the other from Mexico (Palenque, Maya Classic period 320-840 A.D.), to acquire new archeointensity data in order to better constrain the secular variation of the geomagnetic field. By comparing my data with those available in the literature and with the various global and regional models, I showed that the secular variations during the Neolithic in Greece and during the first millennium in Central America are poorly defined. My data suggest that local components, not described by global models, may exist in these regions. They reinforce the importance of developing specific regional models. As a consequence, the acquisition of new high quality data is of main importance. The second part presents the description of a geomagnetic field reversal. This work was based on two points : first by studying transitional directions to provide new constraints on the possible preferred longitudinal paths of virtual geomagnetic poles (VGPs) and second by checking transitional paleointensities obtained on a volcanic sequence in Akaroa volcano (New Zealand). Indeed the transitional field intensity is significantly higher than the field intensity before and after the reversal. We re-sampled this sequence, and the directional results show a complex sequence of N-T-R-T-N-T-R polarity. The transitional VGPs obtained are clustered in two longitudinal bands through Australia and America. This observation seems to reinforce the assumption of a core-mantle interaction over several million years. Following a rock magnetic study, I selected samples that could provide a value for the Thellier and multispecimen paleointensity methods. The obtained paleointensity are relatively low (about 20 μT) during the polarity change and strong at the end of the sequence. Based both on the field strength values and on the radiochronological ages, showing that the sequence was erupted in a very short time, I suggest that only the C4AR.1n-C4Ar.1r reversal was recorded in this sequence. In this assumption, the reversal shows a complex path comparable to other reversals recorded in the northern hemisphere (for example the Steens Mountain ), including a rebound before stabilizing. Finally the last part is devoted to the development of a new methodology and a new apparatus to determine absolute paleointensity. Following the low success rate of paleointensity experiments from the previous study, I decided to test the multispecimen protocol, which can be applied to samples yielding a predominant multidomaine behavior. The main technical drawback of this method lies in the application of the laboratory field along the natural remanent magnetization, a difficult task to perform accurately in standard paleointensity ovens. Thus, we decided to adapt sample holders from our standard oven in order to allow the sample orientation in space and to develop an ultra-fast heating oven prototype particularly well-suited for this method, allowing to apply the laboratory field in the 3 dimensions. I checked the different multispecimen protocols on historical lavas from Reunion and Etna volcano, yielding very different magnetic mineralogies. For all flows, I obtained paleointensities very close from the expected values, regardless from the magnetic mineralogy, revealing the feasibility of our apparatus and the promising interest of the method. The application of various corrections on the statistical estimation of the intensity value or on the cooling rate had no significant impact on my results.
La première partie de ma thèse porte sur l'archéomagnétisme, discipline qui permet de retracer l'évolution temporelle du champ magnétique terrestre au travers des derniers millénaires, principalement à partir des matériaux archéologiques. J'ai étudié deux jeux d'échantillons provenant pour l'un de la Grèce (période néolithique, 6800-3200 avant J.C.) et pour l'autre du Mexique (Palenque, période Maya Classique 320-840 après J.C.), dans le but d'acquérir de nouvelles données d'archéointensité et de mieux contraindre la variation séculaire du champ magnétique terrestre. La comparaison de mes données avec celles disponibles dans la bibliographie et avec les différents modèles globaux et régionaux a mis en évidence que les variations séculaires au Néolithique en Grèce et au cours du premier millénaire en Amérique Centrale sont très mal définies. Mes données suggèrent que des composantes locales, non prisent en compte dans les modèles globaux peuvent exister au niveau de ces régions. Elles renforcent l'intérêt de développer des modèles régionaux précis. Pour ce faire, l'acquisition de nouvelles données de haute qualitéest un élément majeur. La deuxième partie traite de la description d'un renversement du champ magnétique terrestre. Cette étude a été basée sur deux points précis : étudier les directions transitionnelles afin d'apporter de nouvelles contraintes sur le possible confinement longitudinal des pôles géomagnétiques virtuels (PGV) d'une part, et d'autre part vérifier des paléointensités transitionnelles obtenues sur la séquence volcanique d'Akaroa (Nouvelle Zélande), dont l'intensité est significativement supérieure à celles des intensités avant et après le renversement. Nous avons ré-échantillonné cette séquence, et l'évolution directionnelle obtenue pour ce renversement est une succession complexe de polarités N-T-R-T-N-T-R. Les PGV obtenus semblent se regrouper sous deux bandes longitudinales sous l'Australie et l'Amérique, ce qui renforce l'hypothèse d'une interaction entre le manteau et le noyau sur plusieurs millions d'années. Suite à une étude de minéralogie magnétique, j'ai sélectionné les échantillons susceptibles de fournir une valeur de paléointensité par les méthodes de Thellier et du multispecimen. Les paléointensités obtenues sont relativement faibles (environ 20 μT) au cours du changement de polarité et forte à la fin de la séquence. Mon interprétation, basée à la fois sur les valeurs de l'intensité du champ et sur les données radiochronologiques montrant que la séquence s'est mise en place très rapidement, est de considérer que seul le renversement C4Ar.1n-C4Ar.1r a été enregistré dans cette séquence. Dans cette hypothèse, le renversement montre un cheminement complexe comparable à d'autres renversements enregistrés dans l'hémisphère nord (comme celui de la Steens Mountain par exemple), incluant un phénomène de rebond avant de se stabiliser. La troisième partie de ma thèse est consacrée au développement d'une nouvelle méthodologie et d'un nouvel appareillage pour déterminer des paléointensités. Le faible taux de réussite des expériences de paléointensité de l'étude précédente m'a poussé à m'intéresser au protocole multispecimen, qui peut s'appliquer aux échantillons possédant un comportement polydomaine. L'inconvénient technique majeur de cette méthode réside dans l'application du champ le long de l'aimantation naturelle, difficile à réaliser avec précision dans les fours standards. Pour ce faire, nous avons décidé de développer des porte-échantillons permettant d'orienter les échantillons dans l'espace pour le four standard et un prototype de four à chauffage ultra-rapide particulièrement bien adapté avec la possibilité d'orienter le champ appliqué dans les 3 dimensions. J'ai testé les différents protocoles de la méthode sur des laves historiques de la Réunion et de l'Etna, possédant des minéralogies très différentes. Pour l'ensemble des coulées étudiées, j'ai obtenu des paléointensités très proches des valeurs attendues, et ce indépendamment de la minéralogie, révélant ainsi le faisabilité de notre appareillage et le côté prometteur de la méthode. L'application de diverses corrections sur la statistique d'estimation de la valeur de l'intensité ou sur le taux de refroidissement n'ont eu aucun impact notable sur mes résultats.
https://tel.archives-ouvertes.fr/tel-00719380

tel-00719380
https://tel.archives-ouvertes.fr/tel-00719380
https://tel.archives-ouvertes.fr/tel-00719380/document
https://tel.archives-ouvertes.fr/tel-00719380/file/thesefanjat2012.pdf

Éditeur(s) : HAL CCSD American Chemical Society
Résumé : Experiments were conducted to assess the potential impact of fractured well-cement degradation on leakage rate. Permeability was monitored while CO2-enriched reservoir-equilibrated brine was flowed at constant rate through a single fracture in a class G cement core under conditions mimicking geologic sequestration environments (temperature 60 °C, pressure 10 MPa). The results demonstrate that, at least for the conditions used in the experiment, an initial leakage in a 42 μm aperture fracture (permeability = 1.5 × 10-10 m2) can be self-mitigated due to the decrease of the fracture hydraulic aperture after about 15 h. This decrease results from the development of continuous highly hydrated amorphous Si-rich alteration products at the edge of the fracture and the dense carbonation of the bulk cement that mitigate the penetration of the alteration front.
ISSN: 0013-936X

hal-00950088
https://hal.archives-ouvertes.fr/hal-00950088
DOI : 10.1021/es401317c

Éditeur(s) : HAL CCSD
Résumé : In coastal carbonate aquifers submitted to a saline intrusion, water - rock interactions processes at the interface between freshwater and saltwater are a cause for heterogeneities development within the porous media. The dissolutions and precipitations induced by the mixing zone play a major role in the transport properties of the reservoir and so in the long term evolution of the saltwater intrusion. The characterization and the in situ observation of a current saline intrusion in the Llucmajor carbonate platform at the experimental site of Ses Sitjoles (South-Easth of Mallorca Island, Spain), allowed to study the temporal evolution of the saltwater intrusion and the biogeochemical processes active in the mixing zone. The influence of microstructure, characterized using X-Ray microtomography, on the petrophysical and flow properties was investigated in laboratory and flow-through experiments were also conducted to study the modifications of the microstructures when submitted to water - rock interactions processes. The mixing zone at the Ses Sitjoles site appears as quite thick and not very sensitive to climate and anthropic stress and is proved to be the locus of active microbiological activity. Laboratory studies highlight a strong control of the microporosity on transport processes and of pCO2 on water - rock interactions. The percolation experiments of slightly reactive waters reveal calcite dissolution together with a decrease in permeability due to a rearrangement of micro-grains within the microporous network.
Les processus d'interactions fluide-roche à l'interface eau douce-eau salée, dans les aquifères carbonatés côtiers soumis à une intrusion saline, sont une des causes du développement d'hétérogénéités dans la structure du milieu poreux. Les dissolutions et/ou précipitations engendrées par la présence de cette zone de mélange jouent un rôle déterminant pour les propriétés de transport du réservoir et donc l'évolution à long terme de l'intrusion d'eau salée. En prenant l'exemple de la plateforme carbonatée de Llucmajor au niveau du site expérimental de Ses Sitjoles (Sud-Est de Majorque, Espagne), un travail de caractérisation et d'observation in situ à moyen terme de l'intrusion saline actuelle de ce réservoir permet de décrire son évolution temporelle et les processus biogéochimiques actifs dans la zone de mélange. L'influence de la microstructure du milieu poreux, caractérisée par microtomographie RX, sur les propriétés pétrophysiques et hydrodynamiques est étudiée en laboratoire et des expériences de percolations d'eaux réactives (mélanges eau douce - eau salée et eau pure chargée en CO2) sont réalisées afin d'étudier les modifications de ces microstructures lorsqu'elles sont soumises à des interactions eau - roche. La zone de mélange eau douce - eau salée rencontrée au niveau du site de Ses Sitjoles est large et peu sensible aux contraintes extérieures (climatologiques et anthropiques) et constitue un lieu d'activité microbiologique particulièrement actif. En laboratoire, on observe un fort contrôle des phénomènes de transport par la microporosité et des processus d'interactions eau - roche par la pCO2. Dans le cas d'une percolation de fluides moyennement réactifs, les expériences mettent en évidence une dissolution de calcite accompagnée par une diminution de la perméabilité, liée à un réarrangement des micro-grains à l'intérieur du réseau microporeux.
https://tel.archives-ouvertes.fr/tel-00767152

tel-00767152
https://tel.archives-ouvertes.fr/tel-00767152
https://tel.archives-ouvertes.fr/tel-00767152/document
https://tel.archives-ouvertes.fr/tel-00767152/file/thesegaring.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
This study assessed the inhaled dose of alcohol during hand disinfection. Experiments were conducted with two types of hand rub using two hand disinfection procedures. Air samples were collected every 10 s from the breathing zone, by bubbling through a mixture of K2Cr2O7 and H2SO4. The reduction of dichromate ions in the presence of alcohols was followed by UV-vis spectrophotometry. The difference in intensity of the dichromate absorption peak was used to quantify the alcohol concentration expressed in ethanol equivalent. During hygienic hand disinfection, the mean ethanol equivalent concentrations peaked at around 20-30 s for both hand rubs (14.3 ± 1.4 mg/L for hand rub 1 and 13.2 ± 0.7 mg/L for hand rub 2). During surgical hand disinfection, two peaks were found at the same time (40 and 80 s) for both hand rubs. The highest mean concentrations were 20.2 ± 0.9 mg/L for hand rub 1 and 18.1 ± 0.9 mg/L for hand rub 2. For hand rub 1, the total absorbed doses, calculated from ethanol with an inhalation flow of 24 L/min and an absorption rate of 62%, were 46.5 mg after one hygienic hand disinfection and 203.9 mg after one surgical hand disinfection. Although the use of ABHRs leads to the absorption of very low doses, sudden, repeated inhalation of high alcohol concentrations raises the question of possible adverse health effects.
International Journal of Environmental Research and Public Health

hal-00878450
https://hal.archives-ouvertes.fr/hal-00878450
https://hal.archives-ouvertes.fr/hal-00878450/document
DOI : 10.3390/ijerph9030868