Éditeur(s) : HAL CCSD
Résumé : International audience
In most rock mechanical testing devices, the texture developed during deformation is only observed after the failure, and the detailed mapping of cracks and pore structure evolution, just before or after rupture, remains speculative. Computerized X-ray tomography (CT X-ray) offers a way to observe 'in vivo' some characteristics of a tested sample in the course of its deformation. Therefore we developed an X-ray transparent tri-axial cell that was included in a medical purpose X-ray scanner with a volumetric resolution of the order of 1 mm3. This technique is described and applied to a porous calcarenite, which is regularly scanned for porosity evolution during mechanical testing. The experiment is performed at low confining pressure (2-10 MPa). During testing, an axial load is applied until failure and is then progressively decreased. In these experiments, the peak stress is preceded by phase of diffuse dilatancy. After failure localization, the axial stress is unloaded until the stress reaches isotropy. During this unloading phase, the previous diffuse dilatancy is lost due to an elastic relaxation. Then, the stress is completely relaxed. At this moment the dilatancy increases again and the residual dilatancy is larger than that reached at the peak stress. When observed "post mortem" at microscopic scale, the dilatant structures are comprised of cataclastic deformation bands and cracks in some larger crystals.
International Journal of Rock Mechanics and Mining Science

hal-00767563
https://hal.archives-ouvertes.fr/hal-00767563
DOI : 10.1016/j.ijrmms.2012.07.020

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
The upward oil migration in a transparent and rough fracture containing a liquid of higher density is studied experimentally using a light transmission technique. The aperture heterogeneity is also measured by light transmission. The injection of oil in a fracture containing a heavier fluid produces a gravitational fingering instability. Depending on the injection velocity (capillary number, Ca) and the density difference between the two fluids (Bond number, Bo), different patterns are observed during the oil displacements. The width of the finger and its velocity are measured as a function of Bo and Ca. A stability analysis of the interface, based on a generalised Darcy equation in a two-dimensional fracture, allows an accurate description of the experimental results. The order of magnitude of the finger width and its velocity are in good agreement with the calculations, with small disparities due to various unknown fluid flow parameters: capillary pressure, finger thickness in the gap of the fracture, finger tortuosity and oil velocity field into the finger. The theoretical approach allows constructing a (Ca, Bo) phase diagram of stability of the interface.
ISSN: 0169-3913

hal-00429329
https://hal.archives-ouvertes.fr/hal-00429329
DOI : 10.1007/s11242-009-9340-2

Éditeur(s) : HAL CCSD
Résumé : We present an experimental study of relations between hydraulic properties of clayey rocks and their deformation at bulk and micro scale. The experimentation is based on triaxial deformation of kaolinitic core samples, on permeability measurements, and on several methods of analysis of the microstructure. To produce the samples, remoulded kaolinite material is consolidated by axial loading up to 20 MPa in an oedometric cell. Then, in a triaxial cell, an undrained stress path is applied in order to induce shearing damage in the sample. The permeability of the sample is measured by fluid flow across the sample. Before and after these hydro-mechanical tests, the evolution and the homogeneity of the pore space and moreover the texture of the material are analysed by X-ray tomography, environmental scanning electron microscopy and thermic neutron diffraction. Contrary to expectations, the permeability at the sample scale does not vary significantly, although quite large deformation is reached. The final deformation is heterogeneous, with well-developed shear bands. It appears that the development of compacting and dilating zones generates a heterogeneous permeability field, which results in a negligible variation of the bulk permeability at the sample scale.
International Journal of Rock Mechanics and Mining Science

hal-00496407
https://hal.archives-ouvertes.fr/hal-00496407
DOI : 10.1016/j.ijrmms.2010.04.007

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Secondary migration is defined as the movement of hydrocarbons through relatively permeable rocks from source to trap: a two-phase flow within a porous medium. Depending on the geometry and capillary pressure distributions of carrier beds, secondary migration has both vertical and lateral components. The present paper focuses on that part of the migration where the movement is mainly vertical. Its objective is to propose a description of the dynamics governing the vertical part of secondary migration based on the main physical aspects of two-phase flow in a homogeneous porous medium. The study is illustrated by laboratory observations performed in a vertical, 2-D Hele-Shaw cell filled with a transparent porous medium where the flow of dyed oil invading a wetting fluid is visually observed. These observations help us to understand the effect of buoyant, capillary and viscous forces on the resulting flow, the relative importance of which is characterized by non-dimensional numbers. Extrapolating these observations to natural media, it is proposed that vertical secondary migration can be described as a percolation of disconnected and vertically-elongated stringers. These stringers do not move continuously but as a succession of snap-off and re-feeding events which result in a jerky upward movement. Using parameters characterizing the physical properties of the fluid and of the porous medium, the geometry and the dynamic behavior of the stringers are estimated. The width of stringers occurring during secondary migration in geological media is centimetric and their vertical size ranges from several centimeters to a few meters. An upper limit of the mean upward velocity of stringers is proposed, as well as an estimate of their spatial density and of the minimum, average horizontal distance (decametric) between two stringers. The stringers are sparsely distributed, resulting in a low average oil loss and a high efficiency of the vertical migration process.
ISSN: 0264-8172

hal-00831370
https://hal.archives-ouvertes.fr/hal-00831370
https://hal.archives-ouvertes.fr/hal-00831370/document
https://hal.archives-ouvertes.fr/hal-00831370/file/pekins-V-edited.pdf
DOI : 10.1016/j.marpetgeo.2013.04.020

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The brittle structures of a Hercynian granite (La Borne, French Massif Central) observed at several scales, from regional to microscopic, are presented and interpreted on mechanical terms. Emphasis is placed on strike slip faults, joints, and cracks related to incipient shear fracturing during horizontal compression. Three compressive tectonic phases have been identified according to their brittle structures and characterised by the burial depth at the time of their generation.The two first phases (H1, H2) are Hercynian and occurred while the granite was deeply buried (∼5 to 3 km depth) whereas the last phase (P) is Pyrenean and occurred at very low depth. The geometric organizations of cracks, joints and faults are clearly similar at various scales from about 10 μm to several m.These field observations are strong arguments for the occurrence of shear structures at microscopic to macroscopic scales during tectonic events. Following this inference, it is proposed that, at least in the case of Hercynian phases, cracks, joints and macroscopic strike slip faults have been generated by the same mechanical process under high overburden weight. Therefore, incipient fractures seem to be generated as shearing structures and to evolve by coalescence with neighbouring ones with the same direction.
ISSN: 0191-8141

hal-01115718
https://hal.archives-ouvertes.fr/hal-01115718
DOI : 10.1016/j.jsg.2014.05.002