Éditeur(s) : HAL CCSD Institute of Electrical and Electronics Engineers (IEEE)/Optical Society of America(OSA)
Résumé : International audience
Nanometric displacement measurements by Extrinsic Fiber Fabry-Perot interferometers (EFPI) is extremely susceptible to external environmental changes. Temperature, in particular, has a remarkable influence on the optical power and wavelength of the laser diode in use, in addition to the thermal expansion of the mechanical structure. In this paper we propose an optimization of the EFPI sensor in order to use it for very long-term (more than one year) and for high-precision displacement measurements. For this purpose, a real time and adaptive estimation procedure based on a homodyne technique and a Kalman filter is established. During a sinusoidal laser diode current modulation, the Kalman filter provides a correction of the amplitude drift caused by the resultant optical power modulation and external perturbations. Besides, stationary temperature transfer operators are estimated via experimental measurements to reduce the additive thermal noise induced in the optical phase and mechanical components.
ISSN: 0733-8724

hal-00876339
https://hal.archives-ouvertes.fr/hal-00876339
DOI : 10.1109/JLT.2012.2194476

Éditeur(s) : HAL CCSD American Institute of Physics
Résumé : International audience
In order to be able to provide valuable data in multiparameter measurement field operations, tiltmeters need to have a noise level better or equal than 10-9 rad for a period range from a few minutes to a few years and a long term stability ranging from 10-7 to 10-8 rad/yr. Tiltmeter measurements should also be as much as possible insensitive to thermal disturbances, by taking great care of the horizontality of the base line tube first. Secondly, thermal responses have been assessed. We also took great care of the coupling of our tiltmeters with the bedrock. We've designed a long base tiltmeter with sensors in silica which has a low dilatation coefficient. The linear variable displacement transducer is based on coil coupling (powered by an alternative voltage). Finally we show the results of two 100 m silica water tube tiltmeters which were installed in a mine in the French Vosges massif in the framework of a hydrology research project. These instruments show a remarkably good stability (6.5×10-9 rad/month) and a low noise level (of the order of 10-11 rad). Toroidal and spheroidal free modes of the Earth were observed after the two last major earthquakes on Sumatra.
ISSN: 0034-6748

hal-00708013
https://hal.archives-ouvertes.fr/hal-00708013
https://hal.archives-ouvertes.fr/hal-00708013/document
https://hal.archives-ouvertes.fr/hal-00708013/file/2008_RSI.pdf
BIBCODE : 2008RScI...79c4502B

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Sensitive instruments like strainmeters and tiltmeters are necessary for measuring slowly varying low amplitude Earth deformations. Nonetheless, laser and fibre interferometers are particularly suitable for interrogating such instruments due to their extreme precision and accuracy. In this paper, a practical design of a simple pendulum borehole tiltmeter based on laser fibre interferometric displacement sensors is presented. A prototype instrument has been constructed using welded borosilicate with a pendulum length of 0.85 m resulting in a main resonance frequency of 0.6 Hz. By implementing three coplanar extrinsic fibre Fabry-Perot in-terferometric probes and appropriate signal filtering, our instrument provides tilt measurements that are insensitive to parasitic deformations caused by temperature and pressure variations. This prototype has been installed in an underground facility (Rustrel, France) where results show accurate measurements of Earth strains derived from Earth and ocean tides, local hydro-logic effects, as well as local and remote earthquakes. The large dynamic range and the high sensitivity of this tiltmeter render it an invaluable tool for numerous geophysical applications such as transient fault motion, volcanic strain and reservoir monitoring.
ISSN: 0956-540X

hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967/document
https://hal.archives-ouvertes.fr/hal-01265967/file/HCS1.pdf
DOI : 10.1093/gji/ggv358

Éditeur(s) : HAL CCSD
Résumé : International audience
A fiber interferometer interfaced to 3 geo-mechanical elements is presented for applications in geophysics. The fiber sensor is based on an extrinsic fiber Fabry-Perot interferometer (EFFPI) which incorporates a modulation scheme to lock the interferometer at quadrature and to enable displacement measurements below a quarter of the interrogating wavelength. It operates over a relatively large frequency dynamic of ~500000 with a precision better than 2 nm. The fiber interferometer is next interfaced to a differential hydrostatic long baseline inclinometer, a 3-axis borehole tiltmeter and a single-axis seismometer, respectively. Results obtained demonstrate that the fiber interferometrically-interrogated instruments exhibit performances equivalent to or even surpassing those of the reference instruments employed for comparison during their deployment to an underground test site since March 2012. Keywords—modulation-based extrinsic fiber Fabry-Perot interferometer; fiber optique hydrostatic inclinometer; fiber optique borehole tiltmeter; fiber optique seismometer
IEEE SENSORS 2015
Busan, South Korea

hal-01265963
https://hal.archives-ouvertes.fr/hal-01265963
https://hal.archives-ouvertes.fr/hal-01265963/document
https://hal.archives-ouvertes.fr/hal-01265963/file/HCS3.pdf
DOI : 10.1109/ICSENS.2015.7370316