Éditeur(s) : HAL CCSD ACSM
Résumé : International audience
PURPOSE AND METHODS: This study was designed to compare the physiological responses and performance of well trained cyclists riding with two different chainring designs, round or eccentric, during a brief and intense cycling exercise: an "all-out" 1-km laboratory test. The eccentrically designed chainring was made of two crank arms sliding into each other, with the inside arm fixed on the center of the arm of a circular chainring and the outside arm sliding along the inside and revolving around an elliptical cam. This design increases crank arm length at the downstroke and decreases it during the upstroke, thus increasing and decreasing the torque. In terms of the chainring's revolution, the crank arm length at 0 degrees and 180 degrees is similar to the arm length of circular chainrings (175 mm). However, during the downstroke (0-180 degrees ), it increases to its maximum length of 200 mm at 90 degrees and then returns to its original length of 175 mm at 180 degrees. During the upstroke, it decreases to a minimum length of 150 mm at 270 degrees and then increases to 175 mm at 360 degrees. Eleven cyclists performed an all-out 1-km laboratory test using each chainring. The study was conducted over two consecutive weeks with the order of chainring use randomized. During all trials, ventilatory data were collected every minute using an automated breath-by-breath system. Heart rate was measured using a telemetry system. RESULTS: None of the cardiorespiratory variables showed significant differences between chainring trials. Performance, however, was significantly improved using the eccentric design (64.25 +/- 1.05 vs 69.08 +/- 1.38 s, P < 0.004, with the eccentric and the round design, respectively). CONCLUSION: We concluded that the eccentric chainring significantly improved the cycling performance during an all-out 1-km test. Further testing with indoor cycling specialists performing on a velodrome would be helpful to define the maximal possibilities of such a chainring.
Medicine & Science in Sports & exercise

hal-00720551
https://hal.univ-antilles.fr/hal-00720551
https://hal.univ-antilles.fr/hal-00720551/document
https://hal.univ-antilles.fr/hal-00720551/file/Article.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This study compared the conventional parameters of anaerobic cycling power in physically active non-cyclists using the Pro-Race® system and a traditional chainring. The force--velocity test was chosen for this purpose because it is the shortest validated cycling laboratory test in which each parameter of maximal anaerobic power can be estimated. The power output (Wmax) and the force at whichWmax is produced (Fopt) were significantly improved with the eccentric chainring (1100±227W versus 1006±197W and 1.39±0.15 N/kg body mass versus 1.13±0.16 N/kg body mass with the eccentric and round designs, respectively; P < 0.006 and P < 0.0004, respectively). The power gained (delta power) was significantly correlated with the eccentric chainring Fopt (r = 0.649; P < 0.05), the mid-thigh circumference (r = 0.685; P < 0.05), the estimated lean thigh volume (r = 0.765; P < 0.01) and the estimated lean lower limb volume (r = 0.665; P < 0.05). We concluded that the eccentric chainring significantly improved the estimated anaerobic power output during a force--velocity test by increasing the force component, Fopt. Cautious interpretation of our results suggests that the subjects with physical attributes that contribute to developing high forces may have a significant advantage in performing with the eccentric chainring.
ISSN: 1440-2440

hal-00703458
https://hal.univ-antilles.fr/hal-00703458
DOI : 10.1016/j.jsams.2007.06.004

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Active mechanisms of re-orientation are necessary to maintain the verticality of tree stems. They are achieved through the production of reaction wood, associated with circumferential variations of three factors related to cambial activity: maturation strain, longitudinal modulus of elasticity (MOE) and eccentric growth. These factors were measured on 17 mature trees from different botanical families and geographical locations. Various patterns of circumferential variation of these factors were identified. A biomechanical analysis based on beam theory was performed to quantify the individual impact of each factor. The main factor of re-orientation is the circumferential variation of maturation strains. However, this factor alone explains only 57% of the re-orientations. Other factors also have an effect through their interaction with maturation strains. Eccentric growth is generally associated with heterogeneity of maturation strains, and has an important complementary role, by increasing the width of wood with high maturation strain. Without this factor, the efficiency of re-orientations would be reduced by 31% for angiosperms and 26% for gymnosperms. In the case of angiosperms, MOE is often larger in tension wood than in normal wood. Without these variations, the efficiency of re-orientations would be reduced by 13%. In the case of gymnosperm trees, MOE of compression wood is lower than that of normal wood, so that re-orientation efficiency would be increased by 24% without this factor of variations.
ISSN: 0931-1890

hal-01031825
https://hal.archives-ouvertes.fr/hal-01031825
DOI : 10.1007/s00468-005-0407-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Studies on tree biomechanical design usually focus on stem stiffness, resistance to breakage or uprooting, and elastic stability. Here we consider another biomechanical constraint related to the interaction between growth and gravity. Because stems are slender structures and are never perfectly symmetric, the increase in tree mass always causes bending movements. Given the current mechanical design of trees, integration of these movements over time would ultimately lead to a weeping habit unless some gravitropic correction occurs. This correction is achieved by asymmetric internal forces induced during the maturation of new wood. The long-term stability of a growing stem therefore depends on how the gravitropic correction that is generated by diameter growth balances the disturbance due to increasing self weight. General mechanical formulations based on beam theory are proposed to model these phenomena. The rates of disturbance and correction associated with a growth increment are deduced and expressed as a function of elementary traits of stem morphology, cross-section anatomy and wood properties. Evaluation of these traits using previously published data shows that the balance between the correction and the disturbance strongly depends on the efficiency of the gravitropic correction, which depends on the asymmetry of wood maturation strain, eccentric growth, and gradients in wood stiffness. By combining disturbance and correction rates, the gravitropic performance indicates the dynamics of stem bending during growth. It depends on stem biomechanical traits and dimensions. By analyzing dimensional effects, we show that the necessity for gravitropic correction might constrain stem allometric growth in the long-term. This constraint is compared to the requirement for elastic stability, showing that gravitropic performance limits the increase in height of tilted stem and branches. The performance of this function may thus limit the slenderness and lean of stems, and therefore the ability of the tree to capture light in a heterogeneous environment.
ISSN: 0022-5193

hal-00534316
https://hal.archives-ouvertes.fr/hal-00534316
DOI : 10.1016/j.jtbi.2008.10.011

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
The main biological function of reaction wood is to act as “muscle” for trees, enabling them to control their posture and right stems when they are permanently disturbed from their set-point inclination by gravity or winds. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called “maturation strains”. Moreover, this function is basically performed through the asymmetric formation of wood (in quantity or quality) around the tree circumference. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity, as an asymmetric force associated to maturation strains creates a bending moment (i.e. one side of the stem “pulls” the other one). We will discuss the traits (cross sectional size and shape, wood features as G fibers or microfibril angle, eccentric growth even in usual or extreme cases as buttresses, total biomass growth and height of center of mass, stem lean and set-point angle) involved to understand how the posture control works. We will give simple formulas to estimate a “muscle efficiency” from biomechanical modeling. We will give practical methods to estimate all the involved traits, especially maturation strains from direct and indirect measurements, in peripheral functional wood or by retrospective dendrochronological analysis. Then, we will illustrate how tree stem tropisms and especially gravitropism, widely studied by physiologists, are key processes in natural ecosystems, through practical examples from tropical rainforest tree communities and regeneration of European mixed beech forests. Using the previous definition of postural control efficiency, we will show that the cross section size is rapidly a limiting factor, opposing the extreme strategies of flexible small stems, which bend easily but also right themselves quickly, to stiff big stems. Lastly, as wood in living trees ensures general storage, defence, vascular and skeletal functions, we will ask general questions about synergies and trade-offs between posture control and other functions.
Botany 2014 : new frontiers in botany
Boise, United States

hal-01627031
https://hal.archives-ouvertes.fr/hal-01627031