Éditeur(s) : HAL CCSD MDPI
Résumé : International audience
LiDAR (Light Detection And Ranging) remote sensing has been shown to be a good technique for the estimation of forest parameters such as canopy heights and above ground biomass. Whilst airborne LiDAR data are in general very dense but only available over small areas due to the cost of their acquisition, spaceborne LiDAR data acquired from the Geoscience Laser Altimeter System (GLAS) have a coarser acquisition density associated with a global cover. It is therefore valuable to analyze the integration relevance of canopy heights estimated from LiDAR sensors with ancillary data such as geological, meteorological, and phenological variables in order to propose a forest canopy height map with good precision and high spatial resolution.In this study, canopy heights extracted from both airborne and spaceborne LiDAR, were first extrapolated from available environmental data (e.g. geology, slope, vegetation indices, etc.). The estimated canopy height maps using random forest (RF) regression from the airborne or GLAS calibration datasets showed similar precisions (RMSE better than 6.5 m). In order to improve the precision of the canopy height estimates regression-kriging (kriging of random forest regression residuals) was used. Results indicated an improvement in the RMSE (decrease from 6.5 to 4.2 m) for the regression-kriging maps from the GLAS dataset, and from 5.8 to 1.8 m for the regression-kriging map from the airborne LiDAR dataset. Finally, in order to investigate the impact of the spatial sampling of future LiDAR missions on the precision of canopy height estimates, six subsets were derived from the initial airborne LiDAR dataset with flight line spacing of 5, 10, 20, 30, 40 and 50 km (corresponding to 0.29, 0.11, 0.08, 0.05, 0.04, and 0.03 points/km² respectively). Results indicated that using the regression-kriging approach achieved a precision of 1.8 m on the canopy height map with flight line spacing of 5 km and achieved an average RMSE of 4.8m for the configuration for the 50 km flight line spacing.
ISSN: 2072-4292

hal-01361343
https://hal.archives-ouvertes.fr/hal-01361343
https://hal.archives-ouvertes.fr/hal-01361343/document
https://hal.archives-ouvertes.fr/hal-01361343/file/mt2016-pub00048036.pdf
DOI : 10.3390/rs8030240

Éditeur(s) : HAL CCSD Yokohama
Résumé : International audience
We make use of the viscosity technique to develop a convergent method for approximating a common element of the set of fixed points of a demicontractive operator and the set of solutions of a monotone equilibrium problem. The proposed algorithm is obtained by coupling a modified hybrid steepest descent method with the extragradient algorithm. Under mild conditions, the strong convergence of the sequences generated by the algorithm is obtained. Using this result we obtain two corollaries which improve or develop several corresponding results in this field.
Journal of Nonlinear and Convex Analysis

hal-00779988
https://hal.univ-antilles.fr/hal-00779988

Éditeur(s) : HAL CCSD
Résumé : IGARSS 2015, Milan, ITA, 26-/07/2015 - 31/07/2015
International audience
LiDAR remote sensing has been shown to be a good technique for the estimation of forest parameters such as canopy heights and aboveground biomass. Whilst airborne LiDAR data are in general very dense but only available over small areas due to the cost of their acquisition, spaceborne LiDAR data acquired from the Geoscience Laser Altimeter System (GLAS) have a coarser acquisition density associated with a global cover. It is therefore valuable to analyze the integration relevance of canopy heights estimated from LiDAR sensors with ancillary data such as geological, meteorological, and phenological variables in order to propose a forest canopy height map with good precision and high spatial resolution.In this study, canopy heights extracted from both airborne and spaceborne LiDAR, were first extrapolated from available environmental data. The estimated canopy height maps using random forest (RF) regression from the airborne or GLAS calibration datasets showed similar precisions (RMSE better than 6.5 m). In order to improve the precision of the canopy height estimates regression-kriging (kriging of RF regression residuals) was used. Results indicated an improvement in the RMSE (decrease from 6.5 to 4.2 m) for the regression-kriging maps from the GLAS dataset, and from 5.8 to 1.8 m for the regression-kriging map from the airborne LiDAR dataset.
Geoscience and Remote Sensing Symposium (IGARSS), 2015 IEEE International
Milan, Italy

hal-01244677
https://hal.archives-ouvertes.fr/hal-01244677
https://hal.archives-ouvertes.fr/hal-01244677/document
https://hal.archives-ouvertes.fr/hal-01244677/file/mt2015-pub00044297.pdf
DOI : 10.1109/IGARSS.2015.7326729