Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
An intensive water vapour intercomparison effort, involving airborne and ground-based water vapour lidar systems, was carried out in the framework of the COPS experiment. The main objective of this paper is to provide accurate error estimates for these systems. Comparisons between the ground-based Raman lidar BASIL and the airborne CNRS DIAL (Differential Absorption Lidar) indicate a mean relative bias between the two sensors, calculated with respect to the mean value of −2.13% (−0.034 g kg−1) in the altitude region 0.5-3.5 km, while comparisons between BASIL and the airborne DLR DIAL lead to a mean relative bias of 1.87% (0.018 g kg−1) in this same altitude region. Comparisons between the ground-based UHOH DIAL and the CNRS DIAL indicate a bias of −3.2% (−0.37 × 1022 m−3) in the altitude range 1.5-4.5 km, while comparisons between the UHOH DIAL and the DLR DIAL indicate a bias of 0.83% (0.06 × 1022 m−3) in this same altitude range. Based on the available comparisons between the ground-based Raman lidar BERTHA and the CNRS DIAL, the mean relative bias is found to be −4.37% (−0.123 g kg−1) in the altitude region 0.5-4.5 km. Comparisons between the ground-based IGN Raman lidar and the CNRS DIAL indicate a bias of 3.18% (0.55 g kg−1) in the altitude range from 0.5 to 4.5 km, while comparisons between the CNRS DIAL and DLR DIAL result in a mean relative bias of 3.93% (1.1 × 1022 m−3) in the altitude interval 0.5-4.0 km. Based on the available statistics of comparisons, benefiting from the fact that the CNRS DIAL was able to be compared with all other lidar systems, and putting equal weight on the data reliability of each instrument, overall relative values for BASIL, BERTHA, IGN Raman lidar, UHOH DIAL, DLR DIAL, and CNRS DIAL, with respect to the mean value, are found to be −0.38, −2.60, 4.90, −1.43, −2.23 and 1.72%, respectively.
ISSN: 0035-9009

hal-00572576
https://hal.archives-ouvertes.fr/hal-00572576
DOI : 10.1002/qj.697

Éditeur(s) : HAL CCSD
Résumé : French Guiana is a region located on the Guiana Shield in South America. Is presents at the same time a high originality in biodiversity, a good state of conservation and a strong correlation to Amazonian carbon stocks. Knowledge on evolution of the forest structure of French Guiana is however still insufficient to bring an optimal management at territory scale. Availability as never seen before of remote sensing data at high spatial resolution such as LiDAR, on large coverage, offers the opportunity to assess the forest resource in French Guiana. The work done during this thesis aim mostly to study the structure and the variations of the canopy height, the factors determining its variability and the consequences of forest logging activities. The data used during this thesis come from an airborne LiDAR and field data from Office National des Forêts (ONF). This thesis manuscript is divided in three parts. The first part introduces the problem and sets the objectives of the thesis. The second part takes the so-called "article" form, that is, the different chapters that compose it are scientific articles published or in the course of publication, it is composed of three studies (I) A study on the gaps detection and environmental determinants on the gap sizes distribution in natural forest: How to characterize the gap size distribution and are there environmental determinants that influence the statistical distribution of gap size? This article has been submitted in Biogeoscience. (ii) A study of the control of the environment on the canopy height structure and variations at different spatial resolutions. Which spatial scales are relevant for analyzing the environmental determinants of canopy height changes in tropical forests from remote sensing data? How can the environment help or not map the height of the canopy in the rainforest? This article was accepted for publication in Remote Sensing. (iii) a third study where we quantified the effects of Reduced Impact Logging (RIL) on the structure and variation of canopy height. What are the effects of logging on canopy height variations and gap size distribution? This article will be submitted for publication in a Forest Ecology and Management journal. In the last part, after a synthesis of the main results, we propose a conclusion.
La Guyane française est une région située sur le Plateau des Guyanes en Amérique du sud. Elle présente à la fois une grande originalité en termes de biodiversité, un bon état de conservation et une forte contribution au stock de carbone Amazonien. Les connaissances sur l’évolution de la structure forestière de la Guyane française restent cependant insuffisantes pour offrir une gestion optimale à l’échelle du territoire. La disponibilité sans précédent de données de télédétection à très haute résolution spatiale telles que le LiDAR , sur de larges couvertures nous offre l'opportunité d’évaluer la ressource forestière de la Guyane Française. Les travaux réalisés dans le cadre de cette thèse visent prioritairement à étudier la structure et les variations de la hauteur de canopée, les facteurs déterminant sa variabilité ainsi que les conséquences des activités d’exploitation forestière. Les données utilisées au cours de la thèse proviennent d’un LiDAR aéroporté et des données de terrains de l'Office National des Forêts (ONF). Ce manuscrit de thèse est divisé en trois grandes parties. La première partie introduit la problématique et fixe les objectifs de la thèse. La seconde partie prend la forme dite « sur article », c'est-à-dire que les différents chapitres qui la compose sont des articles scientifiques publiés ou en cours de publication, elle est composée de trois études. (i) Une étude concernant la détection des trouées et des déterminants environnementaux sur la distribution de tailles des trouées en forêt non exploitée : Comment caractériser la distribution de taille des trouées et est-ce qu’il y a des déterminants environnementaux qui influencent la distribution statistique de taille de trouées? Cet article à été soumis dans Biogeoscience. (ii) Une étude du contrôle de l'environnement sur la structure et les variations de la hauteur de canopée à différentes résolutions spatiales. Quelles échelles spatiales sont pertinentes pour analyser les déterminants environnementaux des variations de hauteur de la canopée en forêt tropicale à partir des données de télédétection ? Comment l’environnement peut aider, ou pas, à cartographier la hauteur de la canopée en forêt tropicale ? Cet article à été accepté pour publication dans Remote Sensing. (iii) Une troisième étude où nous avons quantifié les effets de l’exploitation à faible impact (EFI) sur la structure et la variation de la hauteur de canopée. Quelles sont les effets de l’exploitation forestière sur les variations de hauteur de canopée et sur la distribution de taille des trouées ? Cet article sera soumis pour publication dans une revue scientifique (Forest Ecology and Management). Dans la dernière partie, après une synthèse des principaux résultats, nous proposons des pistes de développement.
https://tel.archives-ouvertes.fr/tel-01527553

NNT : 2016YANE0006
tel-01527553
https://tel.archives-ouvertes.fr/tel-01527553
https://tel.archives-ouvertes.fr/tel-01527553/document
https://tel.archives-ouvertes.fr/tel-01527553/file/these-youven-goulamoussene2.pdf

Éditeur(s) : HAL CCSD MDPI
Résumé : International audience
LiDAR (Light Detection And Ranging) remote sensing has been shown to be a good technique for the estimation of forest parameters such as canopy heights and above ground biomass. Whilst airborne LiDAR data are in general very dense but only available over small areas due to the cost of their acquisition, spaceborne LiDAR data acquired from the Geoscience Laser Altimeter System (GLAS) have a coarser acquisition density associated with a global cover. It is therefore valuable to analyze the integration relevance of canopy heights estimated from LiDAR sensors with ancillary data such as geological, meteorological, and phenological variables in order to propose a forest canopy height map with good precision and high spatial resolution.In this study, canopy heights extracted from both airborne and spaceborne LiDAR, were first extrapolated from available environmental data (e.g. geology, slope, vegetation indices, etc.). The estimated canopy height maps using random forest (RF) regression from the airborne or GLAS calibration datasets showed similar precisions (RMSE better than 6.5 m). In order to improve the precision of the canopy height estimates regression-kriging (kriging of random forest regression residuals) was used. Results indicated an improvement in the RMSE (decrease from 6.5 to 4.2 m) for the regression-kriging maps from the GLAS dataset, and from 5.8 to 1.8 m for the regression-kriging map from the airborne LiDAR dataset. Finally, in order to investigate the impact of the spatial sampling of future LiDAR missions on the precision of canopy height estimates, six subsets were derived from the initial airborne LiDAR dataset with flight line spacing of 5, 10, 20, 30, 40 and 50 km (corresponding to 0.29, 0.11, 0.08, 0.05, 0.04, and 0.03 points/km² respectively). Results indicated that using the regression-kriging approach achieved a precision of 1.8 m on the canopy height map with flight line spacing of 5 km and achieved an average RMSE of 4.8m for the configuration for the 50 km flight line spacing.
ISSN: 2072-4292

hal-01361343
https://hal.archives-ouvertes.fr/hal-01361343
https://hal.archives-ouvertes.fr/hal-01361343/document
https://hal.archives-ouvertes.fr/hal-01361343/file/mt2016-pub00048036.pdf
DOI : 10.3390/rs8030240

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
The Convective and Orographically-driven Precipitation Study (COPS) carried out in summer 2007 over northeastern France and southwestern Germany provided a fairly comprehensive description of the low-troposphere water-vapour field, thanks in particular to the deployment of two airborne differential absorption lidar systems. These lidar observations were assimilated using the 3D-Var assimilation system of the Application of Research to Operations at MEsoscale (AROME) numerical weather prediction mesoscale model. The assimilation was carried out for the period 4 July-3 August by running a three-hour forward intermittent assimilation cycle. First, the impact of the lidar observations was assessed by comparing the analyses with a set of more than 200 independent soundings. The lidar observations were found to have a positive impact on the analyses by reducing the dry bias in the first 500 m above ground level and by diminishing the root-mean-square error by roughly 15% in the first km. Then the impact of the lidar observations was assessed by comparing the precipitation forecasts (obtained with and without the lidar observations for the period 15 July-2 August) with the gridded precipitation observations provided by the Vienna Enhanced Resolution Analysis. In general, the impact was found to be positive but not significant for the 24 h precipitation and positive and significant for the 6 h precipitation, with an improvement lasting up to 24 h. Some selected case studies show that the improvement was obtained through a better depiction of convection initiation or through a more accurate positioning of the precipitation systems
ISSN: 0035-9009

hal-00659497
https://hal.archives-ouvertes.fr/hal-00659497
DOI : 10.1002/qj.1864

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Knowing the slip amplitudes that large earthquakes produced in prehistorical times is one key to anticipate the magnitude of large forthcoming events. It is long known that the morphology is preserving remnants of paleoearthquake slips in the form of fault-offset landforms. However, the measured offsets that can be attributed to the most recent paleoearthquakes are generally few along a fault, so that they rarely allow recovering the slip distributions and largest slips of these earthquakes. We acquired ~1 m resolution airborne lidar data on a 30 km stretch of a fast-slipping strike-slip fault (eastern Hope Fault, New Zealand) located in a region of high alluvial dynamics where landforms are rapidly evolving. Data analysis reveals >200 offset landforms; only 30% allow a good to moderate quality offset measurement. From these good to moderate quality measures, we recover the slip-length distributions and largest slips of the four most recent large paleoearthquakes and find evidence of 4–6 prior events. The record suggests that large earthquake slip recurred in multiples of about 4 m along the 30 km stretch. Although they have larger uncertainties, the more numerous lower-quality offsets that we also measured reveal a similar earthquake slip record. This shows that, although offset landforms are partly degraded in dynamically active landscapes, they store valuable information on paleoearthquake slips. This information might be recovered provided that the morphology is analyzed at high resolution and " continuously " over a significant fault length. Remote lidar data are powerful to perform such analyses.
ISSN: 2169-9313

insu-01469219
https://hal-insu.archives-ouvertes.fr/insu-01469219
https://hal-insu.archives-ouvertes.fr/insu-01469219/document
https://hal-insu.archives-ouvertes.fr/insu-01469219/file/Manighetti_et_al-2015-Journalsur Geophysical_Research__Solid_Earth.pdf
DOI : 10.1002/2014JB011787

Éditeur(s) : HAL CCSD
Résumé : IGARSS 2015, Milan, ITA, 26-/07/2015 - 31/07/2015
International audience
LiDAR remote sensing has been shown to be a good technique for the estimation of forest parameters such as canopy heights and aboveground biomass. Whilst airborne LiDAR data are in general very dense but only available over small areas due to the cost of their acquisition, spaceborne LiDAR data acquired from the Geoscience Laser Altimeter System (GLAS) have a coarser acquisition density associated with a global cover. It is therefore valuable to analyze the integration relevance of canopy heights estimated from LiDAR sensors with ancillary data such as geological, meteorological, and phenological variables in order to propose a forest canopy height map with good precision and high spatial resolution.In this study, canopy heights extracted from both airborne and spaceborne LiDAR, were first extrapolated from available environmental data. The estimated canopy height maps using random forest (RF) regression from the airborne or GLAS calibration datasets showed similar precisions (RMSE better than 6.5 m). In order to improve the precision of the canopy height estimates regression-kriging (kriging of RF regression residuals) was used. Results indicated an improvement in the RMSE (decrease from 6.5 to 4.2 m) for the regression-kriging maps from the GLAS dataset, and from 5.8 to 1.8 m for the regression-kriging map from the airborne LiDAR dataset.
Geoscience and Remote Sensing Symposium (IGARSS), 2015 IEEE International
Milan, Italy

hal-01244677
https://hal.archives-ouvertes.fr/hal-01244677
https://hal.archives-ouvertes.fr/hal-01244677/document
https://hal.archives-ouvertes.fr/hal-01244677/file/mt2015-pub00044297.pdf
DOI : 10.1109/IGARSS.2015.7326729

Éditeur(s) : Gauthier-Villars
Résumé : The variability of ''yellow substance'' in waters of the Skagerrak and the Kattegat was studied during the international Skagex programme in 1990 and 1991. Data on attenuation of light and fluorescence of dissolved organic matter (DOM) in sea water were collected with a spectral transmissiometer and a submersible fluorometer within a depth range of 0-250 m at several stations. More than fifty-fold variations of fluorescence intensity over space and time were due to the combined action of different sources of DOM in the straits. The surface maximum of fluorescing DOM, related to river outflow, was spreading from Oslo fjord to the central Skagerrak in late spring. This maximum may be ecologically important because it diminishes shortwave PAR. In the autumn the brightest DOM fluorescence was found in the Kattegat and along the Norwegian coast in accordance with earlier studies. The local minima of DOM fluorescence are associated with the Jutland current. Both the instability of the current and a ten-fold difference in DOM content between deep layers of the Skagerrak and Kattegat resulted in strong synoptic variability of fluorescence in the transitional area between the straits. Seasonal and synoptic variabilities of ''yellow substance'' were minimal in the southern Kattegat. The vertical gradients of DOM fluorescence were mostly negative at the depth of the thermocline of the open Skagerrak in spring, reaching values of 40-50 % m-1. Fine structure and complex shape were inherent to fluorescence profiles from areas of intensive water mixing. DOM fluorescence closely covaried with attenuation of UV light: the correlation coefficient was + 0.9 for wavelength w <= 350 nm regardless of season. The inverse dependence between wavelength derivative and magnitude of UV attenuation in the straits did not change with season. DOM fluorescence and water salinity were negatively correlated at depths of 25-50 m but they varied independently in the upper 10 m. No significant correlation between fluorescence and nitrates has been found. Estimates of correlation with phosphates ranged from 0.7 to 0.8. In general, the changes of fluorescence were due to variations of DOM content in sea water but not to variability of DOM composition or state. The properties of DOM fluorescence in the Skagerrak-Kattegat area make it a useful natural tracer of water movements suitable for active remote sensing with airborne lidar.
Oceanologica Acta (0399-1784) (Gauthier-Villars), 1993 , Vol. 16 , N. 2 , P. 115-125

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00099/21041/18667.pdf
http://archimer.ifremer.fr/doc/00099/21041/

Éditeur(s) : Elsevier Science Bv
Résumé : An exceptional structural picture of the immerged Variscan basement, offshore the Leon metamorphic domain, is supplied by high-resolution LiDAR and echosounder data recorded in the Molene archipelago, western Brittany (France). Various types of fabrics are identified and, from in situ rock sample analyses further combined with field structural data, are interpreted on a lineament trajectory map as the trace of magmatic and tectonic structures. Our onshore/offshore study leads us to propose a two-phase kinematic model that emphasizes the role of a strike-slip duplex in an EW-trending relay zone linking the North Armorican and Pierres Noires ductile shear zones (NASZ, PNSZ). Dextral shearing occurred within a transtensional setting, synchronously with magmatic intrusions (St-Renan granite and an offshore gabbro-diorite complex) dated at 314-320 Ma by new U-Th/Pb ages. It post-dated an early regional foliation related to top-to-the-NE ductile transpresional shearing. Our study emphasizes the key role of strike-slip tectonics in the NW part of the Armorica Variscan belt.
Tectonophysics (0040-1951) (Elsevier Science Bv), 2014-09 , Vol. 630 , P. 236-250

Droits : 2014 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/00194/30490/28895.pdf
DOI:10.1016/j.tecto.2014.05.026
http://archimer.ifremer.fr/doc/00194/30490/

Éditeur(s) : HAL CCSD MDPI
Résumé : International audience
Canopy height is a key variable in tropical forest functioning and for regional carbon inventories. We investigate the spatial structure of the canopy height of a tropical forest, its relationship with environmental physical covariates, and the implication for tropical forest height variation mapping. Making use of high-resolution maps of LiDAR-derived Digital Canopy Model (DCM) and environmental covariates from a Digital Elevation Model (DEM) acquired over 30,000 ha of tropical forest in French Guiana, we first show that forest canopy height is spatially correlated up to 2500 m. Forest canopy height is significantly associated with environmental variables, but the degree of correlation varies strongly with pixel resolution. On the whole, bottomland forests generally have lower canopy heights than hillslope or hilltop forests. However, this global picture is very noisy at local scale likely because of the endogenous gap-phase forest dynamic processes. Forest canopy height has been predictively mapped across a pixel resolution going from 6 m to 384 m mimicking a low resolution case of 3 points·km −2. Results of canopy height mapping indicated that the error for spatial model with environment effects decrease from 8.7 m to 0.91 m, depending of the pixel resolution. Results suggest that, outside the calibration plots, the contribution of environment in shaping the global canopy height distribution is quite limited. This prevents accurate canopy height mapping based only on environmental information, and suggests that precise canopy height maps, for local management purposes, can only be obtained with direct LiDAR monitoring.
ISSN: 2072-4292

hal-01590726
https://hal-univ-guyane.archives-ouvertes.fr/hal-01590726
https://hal-univ-guyane.archives-ouvertes.fr/hal-01590726/document
https://hal-univ-guyane.archives-ouvertes.fr/hal-01590726/file/remotesensing-08-00747.pdf
DOI : 10.3390/rs8090747

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Located in central Europe at the junction of the Southern Alps and the Dinarides, the ≈ 100 km long Idrija fault, striking N310 and dipping ≈ 80°NE is often considered as the potential source of the historical 1511 earthquake (estimated macroseismic magnitude: Mm 6.8). Using 1/25,000 to 1/5000 topographical maps, satellite images (SPOT5), 12.5 m illuminated DEM and airborne LiDAR data-derived 1-m-DEM, we examined in detail the Idrija fault trace along a 20-km-long swath in the central portion of the fault. Combining topographic and remote sensing data allows characterizing the recent activity along the Idrija fault and estimating its cumulative displacement along strike.Between Tolmin and Godovič, the fault trace is mostly linear but appears divided into three disconnected segments of 11–20-km-long. Morphological evidences such as offset streams and ridges and major drainage abandonments suggest ongoing movement. At three sites, field observations and LiDAR-DEM analysis allow measuring cumulative dextral offsets comprised between 35 and 65 m. We found two larger offsets of ≈ 140 m and ≈ 360 m at the southeasternmost site. The vertical component is significant and revealed by a rake ranging from 0 to 33°. The derived N303–N310 striking slip-vector is in agreement with the motion along this fault as suggested by the geodesy. Assuming that the smallest measured offsets have been recorded after the last glacial maximum (LGM, about 20 ka ago), the minimum slip-rate for the Idrija fault is about 1.5 mm/yr over this period of time.
ISSN: 0040-1951

hal-01115724
https://hal.archives-ouvertes.fr/hal-01115724
DOI : 10.1016/j.tecto.2014.04.043

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
Within the framework of the international field campaign COPS (Convective and Orographically induced Precipitation Study), a large suite of state-of-the-art meteorological instrumentation was operated, partially combined for the first time. This includes networks of in situ and remote-sensing systems such as the Global Positioning System as well as a synergy of multi-wavelength passive and active remote-sensing instruments such as advanced radar and lidar systems. The COPS field phase was performed from 01 June to 31 August 2007 in a low-mountain area in southwestern Germany/eastern France covering the Vosges mountains, the Rhine valley and the Black Forest mountains. The collected dataset covers the entire evolution of convective precipitation events in complex terrain from their initiation, to their development and mature phase until their decay. Eighteen Intensive Observations Periods with 37 operation days and eight additional Special Observations Periods were performed, providing a comprehensive dataset covering different forcing conditions. In this article, an overview of the COPS scientific strategy, the field phase, and its first accomplishments is given. Highlights of the campaign are illustrated with several measurement examples. It is demonstrated that COPS research provides new insight into key processes leading to convection initiation and to the modification of precipitation by orography, in the improvement of quantitative precipitation forecasting by the assimilation of new observations, and in the performance of ensembles of convection-permitting models in complex terrain.
ISSN: 0035-9009

hal-00565513
https://hal.archives-ouvertes.fr/hal-00565513
DOI : 10.1002/qj.752

Éditeur(s) : HAL CCSD Berlin: A. Asher & Co.
Résumé : International audience
In this work, we compare IASI-retrieved vertical water vapour profiles and related precipitable water over a complex region, namely the Rhine Valley area, during the pre-operational period of IASI exploitation (June?August 2007). Both IASI water vapour mixing ratio profiles and integrated water vapour content are retrieved from L1C radiances spectra using two techniques and compared with water vapour related observations acquired during the Convective and Orographically-induced Precipitation Study (COPS) field campaign that took place in this area at that time (i.e. lidars, radiosoundings and a global positioning system - GPS - station network). This work addresses the issue of IASI vertical spatial resolution and its capability to detect two-layer water vapour structures such as those observed in a mountainous area and which play an important role in convective initiation or inhibition. We found that this capability mostly relies on the type of a-priori background vector (climatology or space-time colocated ECMWF analysis), which is used within the retrieval scheme. Systematic comparison of water vapour products derived from 71 IASI spectra confirms that IASI can retrieve water vapour amounts in 2 km width layers, in the lower troposphere, with an accuracy of approximately 10%.
ISSN: 0369-1845

hal-00923710
https://hal.archives-ouvertes.fr/hal-00923710
https://hal.archives-ouvertes.fr/hal-00923710/document
https://hal.archives-ouvertes.fr/hal-00923710/file/masiello.pdf
DOI : 10.1127/0941-2948/2013/0430

Éditeur(s) : HAL CCSD Coastal Education and Research Foundation
Résumé : Nearshore bars are generally present on sandy coasts and play a significant role in wave breaking and sediment exchange between beach and shoreface. The study area is located on the Languedoc-Roussillon coast in the Gulf of Lions (southern part of the French Mediterranean coast). This microtidal environment is classified as a wave-dominated coast. The sand coast displays different bar systems (single or multiple; straight or crescentic). The alongshore variability of bar morphology in the nearshore zone was investigated in August 2009 during one week, using a topo-bathymetric LIDAR data set (300 km(2)). LIDAR makes it possible to cover a large area in a very short time with a high resolution. The topo-bathymetric LIDAR offers the added benefit of morphological information about the beach-sea transition in very shallow water (below I in), data often difficult if not impossible to obtain with traditional techniques. The purpose of this paper is 1) to depict the distribution of bars and their characteristics along the 180 km coast of the Gulf of Lions; 2) to update the classifications of sand bars typologies in Languedoc-Roussillon; 3) to pay particular attention to the description of the intricate inner system. Globally, cross-shore distribution of subtidal morphologies is characterized by both an outer and an inner system. The outer system is crescent-shaped in the south and straight in the northern part with a distinctive regional delimitation. The inner system comprises an inner bar and, near the coast, a complex fluctuating bar called Low Bar Beach (LBB). Several intermediate states were identified and added to the new classification proposed in this paper. These results clearly emphasize the importance of LIDAR technology for a better understanding of bar behaviour and single and/or multi-bar beach organisation.
ISSN: 0749-0208

hal-00783187
https://hal.archives-ouvertes.fr/hal-00783187

Éditeur(s) : HAL CCSD
Résumé : International audience
Les plages sableuses constituent une frontière mobile et poreuse entre l'océan ouvert et la terre. La compréhension de la circulation dans les nappes de plage est importante pour une variété de processus physiques, biologiques et chimiques. On cherche à caractériser in-situ la dynamique souterraine sous la zone de swash. Le site atelier est la plage microtidale de Rousty (Camargue, France). L'étude, réalisée sur 48h les 13 et 14 décembre 2014, fait partie d'une plus grande campagne de mesure visant à caractériser la réponse hydro-morphologique de la plage de Rousty à une saison hivernale. La période présentée ici correspond à la phase de déclin d'une tempête modérée. La stratégie retenue dans le cadre de ce projet a été de déployer un réseau de15 capteurs de pression enterrés sous la zone de swash. Les caractéristiques des vagues incidentes, à la fois au large et dans la zone de surf interne, ont été mesurées conjointement à l'utilisation d'un LiDAR terrestre haute fréquence permettant de suivre la surface libre et l'évolution du lit sableux à haute fréquence sur la zone de swash. L'analyse des données moyennées dans le temps a mis en évidence la présence d'un schéma de circulation relativement robuste sous la zone de swash, qui se décale vers le large en suivant la descente du niveau moyen et la diminution de l'activité des vagues. La tendancedominante est un écoulement vers le large, avec une intensité maximale de l'ordre de 0.1mm/s modulé par des infiltrations et exfiltrations dans les parties hautes et basses de la zone de swash, respectivement. L'analyse haute fréquence à des événements de swash sélectionnés ont mis en évidence uncycle souterrain caractéristique.
XIV èmes Journées Nationales Génie Côtier – Génie Civil
toulon, France

hal-01357778
https://hal.archives-ouvertes.fr/hal-01357778

Éditeur(s) : HAL CCSD
Résumé : SilviLaser 2015, La Grande Motte, FRA, 28-/09/2015 - 30/09/2015
International audience
The study provides technical guidelines to optimize sampling design parameters in the context of the implementation of biomass predictive models from airborne lidar data. Parameters under study were those easily controlled when implementing an area-based approach, i.e. lidar pulse density and both field sampling protocols and measurements. Parameters most impacting the model accuracy were identified by conducting a one-factor- at -a-time and a global sensitivity analyses. Number and size of field plot, and plot center position accuracy were identified to be the parameters most impacting model accuracy.
Proceedings of silviLaser 2015. Durrieu S. et Véga, C. (eds)
La Grande Motte, France

hal-01286833
https://hal.archives-ouvertes.fr/hal-01286833
https://hal.archives-ouvertes.fr/hal-01286833/document
https://hal.archives-ouvertes.fr/hal-01286833/file/mt2015-pub00046522.pdf
IRSTEA : PUB00046522

Éditeur(s) : HAL CCSD
Résumé : International audience
After the 2009 Morakot typhoon, which triggered numerous large landslides in Taiwan, Mouyen et al. (2013)showed for the first time the potential of time-lapse gravity survey to infer the mass of sediments transferringby landsliding or through rivers. By providing an integrated measurement of masses, gravimetry might thus becomplementary to common methods used to assess the sediments discharge of rivers. But the masses of rocksdisplaced by Morakot were exceptionally large as a result of the record-breaking rainfalls brought by this typhoonand one might wonder to what extent time-lapse gravimetry could record such sediment transfers. In order tobetter assess the capabilities of this method, we set a time-lapse gravity network dedicated to the monitoring ofsuch sediments transfers in Paolai village (south-central Taiwan). Paolai is located near the large Laonong riverwhere temporary alluvial deposits of sediments exist and face steep mountain slopes likely to experience landslides.Both features are considered as potential source of mass transfers, and in turn of temporal gravity changes. Thefirst base gravity measurements were done in November 2015, using absolute and relative gravimeters, and will berepeated every year, before and after the typhoon season. In the same time, we also use a terrestrial lidar to scan thegeometry of both the river and the mountain slopes, hence providing a detailed topographical survey of the studiedarea. Adding Lidar measurements is an efficient strategy to solve for the non-uniqueness of gravity solutions.Meanwhile, we use the Eros morphodynamic model, that combine landsliding and flooding models, to investigatevarious scenarios of landsliding and subsequent sediment transport and compute the gravity changes on a virtualnetwork of gravimeters. This gives us insights on the expected order of magnitudes for these surface sedimenttransfers, which are useful to unravel the induced gravity signal from others sources such as local hydrology orvertical ground displacements. The modeling results also enable us to set network location that are best defined todetect mass changes associated with sediment transfer. The main objective of this study is to test whether timelapsegravity brings a new and reliable information compared to present methods monitoring sediments transfersand landscape evolution.
European Geosciences Union General Assembly 2016
Vienne, Austria

insu-01308554
https://hal-insu.archives-ouvertes.fr/insu-01308554

Éditeur(s) : HAL CCSD Editions Paralia CFL
Résumé : SUBDUNE v0.6 is a very preliminary version of an exploratory model designed tocompute the sea level to the shoreline, combining the effects of various physics, from run-up to tides. It aims at providing an easy-to-use and quick way to estimate water elevation to the beach, assuming morphology is known. Combined with accurate beachdata, such as LIDAR, this engineering tool may provide with end-users an efficient way to quantify submersion.
ISSN: 1760-8716

hal-00854170
https://hal.archives-ouvertes.fr/hal-00854170
DOI : 10.5150/jngcgc.2012.022-B

Éditeur(s) : HAL CCSD Public Library of Science
Résumé : We examined tree-soil habitat associations in lowland forest communities at Paracou, French Guiana. We analyzed a large dataset assembling six permanent plots totaling 37.5 ha, in which extensive LIDAR-derived topographical data and soil chemical and physical data have been integrated with precise botanical determinations. Map of relative elevation from the nearest stream summarized both soil fertility and hydromorphic characteristics, with seasonally inundated bottomlands having higher soil phosphate content and base saturation, and plateaus having higher soil carbon, nitrogen and aluminum contents. We employed a statistical test of correlations between tree species density and environmental maps, by generating Monte Carlo simulations of random raster images that preserve autocorrelation of the original maps. Nearly three fourths of the 94 taxa with at least one stem per ha showed a significant correlation between tree density and relative elevation, revealing contrasted species-habitat associations in term of abundance, with seasonally inundated bottomlands (24.5% of species) and well-drained plateaus (48.9% of species). We also observed species preferences for environments with or without steep slopes (13.8% and 10.6%, respectively). We observed that closely-related species were frequently associated with different soil habitats in this region (70% of the 14 genera with congeneric species that have a significant association test) suggesting species-habitat associations have arisen multiple times in this tree community. We also tested if species with similar habitat preferences shared functional strategies. We found that seasonally inundated forest specialists tended to have smaller stature (maximum diameter) than species found on plateaus. Our results underline the importance of tree-soil habitat associations in structuring diverse communities at fine spatial scales and suggest that additional studies are needed to disentangle community assembly mechanisms related to dispersal limitation, biotic interactions and environmental filtering from species-habitat associations. Moreover, they provide a framework to generalize across tropical forest sites.
ISSN: 1932-6203

hal-01260289
https://hal.archives-ouvertes.fr/hal-01260289
PRODINRA : 342930
DOI : 10.1371/journal.pone.0141488

Éditeur(s) : HAL CCSD Société Française de Photogrammétrie et de Télédétection
Résumé : International audience
ISSN: 1768-9791

hal-01092523
https://hal-agroparistech.archives-ouvertes.fr/hal-01092523

Résumé : L'année 2004, année du vingtième anniversaire de sa création, aura été marquée, pour l'Ifremer, par une intense activité. 2004 a en effet été d'abord une année d'investissements et de résultats: de la biodiversité des massifs de coraux froids à la capacité des bactéries à produire des polymères biodégradables, de l'observation des effets de la crue centennale du Rhône sur les sédiments à la variabilité de l'hydrologie dans l'Atlantique Nord, de l'effet de la pluviométrie en hiver sur la mortalité estivale des huîtres à la sensibilisation environnementale des crevettes aux bactéries pathogènes, au lever par Lidar aéroporté de plus de 900 km² d'estrans de Bretagne, les résultats scientifiques ont été nombreux La technologie n'a pas été en reste avec les progrès de la protection contre la corrosion marine, les essais concluants de l'AUV, la mise à l'eau du Pourquoi pas?, ni les activités de surveillance du fait de l'augmentation des apparitions de toxines dans les coquillages. L'institut a en outre mené en 2004, avec ses ministères de tutelle, un important effort de réflexion sur ses missions et ses priorités, dont le contrat quadriennal 2005-2008, approuvéen conseil à' administration, finalisé en fin d'année et signé le 25 mai 2005 en présence de quatre ministres, trace désormais le cadre, en cohérence avec notre plan stratégique. [OCR NON CONTRÔLE]

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/2004/rapport-4830.PDF
http://archimer.ifremer.fr/doc/00000/4830/