Éditeur(s) : HAL CCSD MDPI AG, Basel, Switzerland
Résumé : International audience
Abstract View references (46)This work shows the preparation of silica membranes by a two-step sol-gel method using tetraethyl orthosilicate in ethanolic solution by employing nitric acid and ammonia as co-catalysts. The sols prepared in pH 6 resulted in the lowest concentration of silanol (Si-OH) species to improve hydrostability and the optimized conditions for film coating. The membrane was tested to desalinate 0.3-15 wt % synthetic sodium chloride (NaCl) solutions at a feed temperature of 22 °C followed by long term membrane performance of up to 250 h in 3.5 wt % NaCl solution. Results show that the water flux (and salt rejection) decrease with increasing salt concentration delivering an average value of 9.5 kg m-2 h-1 (99.6%) and 1.55 kg m-2 h-1 (89.2%) from the 0.3 and 15 wt % saline feed solutions, respectively. Furthermore, the permeate salt concentration was measured to be less than 600 ppm for testing conditions up to 5 wt % saline feed solutions, achieving below the recommended standard for potable water. Long term stability shows that the membrane performance in water flux was stable for up to 150 h, and slightly reduced from thereon, possibly due to the blockage of large hydrated ions in the micropore constrictions of the silica matrix. However, the integrity of the silica matrix was not affected by the long term testing as excellent salt rejection of >99% was maintained for over 250 h. © 2013 by the authors; licensee MDPI, Basel, Switzerland.
ISSN: 2077-0375

hal-01683203
https://hal.univ-antilles.fr/hal-01683203
DOI : 10.3390/membranes3030136

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Carbonised template silica membranes were synthesised and investigated for water desalination for brackish (0.3wt%), sea water (3.5wt%) and brine (7.5wt%) NaCl solutions at temperatures range from 22 to 60°C. The membranes were prepared by a two-step base catalysed sol-gel method using tetraethyl orthosilicate TEOS as the silica precursor and triblock copolymer of Pluronic® P123 as the templating agent. The P123 silica membranes calcined under vacuum only produced high quality membranes by the interlayer-free method. The membranes were stable during testing of up to 250h under different thermal and salt concentration solutions, always delivering very high salt rejections >99.5%. It was found that by increasing the template concentration in the silica matrix from 5 to 50wt%, salt concentration polarisation was greatly reduced. As such, high water fluxes were measured up to 8.5kgm-2h-1 for brackish water and 6.6kgm-2h-1 for brine water. © 2014 Elsevier B.V.
ISSN: 0376-7388

hal-01683210
https://hal.univ-antilles.fr/hal-01683210
DOI : 10.1016/j.memsci.2014.10.026

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Mesoporous cobalt oxide silica matrices and membranes were successfully prepared using a dual acid-base catalysed sol-gel and interlayer-free approach for desalination applications. The effects of cobalt addition (0-35 mol%) on the structure-property relationship of the silica materials and membrane performance were systematically studied as a function of feed salt concentration (0.3-7.5 wt.% NaCl) and temperature (22-60 °C). As cobalt concentration increases beyond 5 mol%, the concentration of tricobalt tetroxide and proportion of silica mesopores were found to increase within the matrices. Silica membranes with high amount of tricobalt tetroxide (35 mol%) were found to be highly mesoporous with water fluxes of 20, 11.3 and 7.7 kg m-2 h-1 for the 0.3, 3.5 and 7.5 wt.% solutions at 60 °C, respectively, with >99.7% salt rejection at all times. This is attributed to the high pore volume (mesopores formation) and structural robustness of the silica network provided by the presence of tricobalt tetroxide. Even higher performance was achieved for low tricobalt tetroxide (mol%) silica membranes with water fluxes of 47.6 (0.3 wt.%) and 31.5 (3.5 wt.%) kg m-2 h-1 at 60 °C, respectively, though with reduced salt rejections of 90%. © 2015 Elsevier B.V.
ISSN: 0011-9164

hal-01683209
https://hal.univ-antilles.fr/hal-01683209
DOI : 10.1016/j.desal.2015.02.034

Éditeur(s) : HAL CCSD MDPI
Résumé : International audience
AbstractThis review provides a global overview of microporous silica based membranes for desalination via pervaporation with a focus on membrane synthesis and processing, transport mechanisms and current state of the art membrane performance. Most importantly, the recent development and novel concepts for improving the hydro-stability and separating performance of silica membranes for desalination are critically examined. Research into silica based membranes for desalination has focussed on three primary methods for improving the hydro-stability. These include incorporating carbon templates into the microporous silica both as surfactants and hybrid organic-inorganic structures and incorporation of metal oxide nanoparticles into the silica matrix. The literature examined identified that only metal oxide silica membranes have demonstrated high salt rejections under a variety of feed concentrations, reasonable fluxes and unaltered performance over long-term operation. As this is an embryonic field of research several target areas for researchers were discussed including further improvement of the membrane materials, but also regarding the necessity of integrating waste or solar heat sources into the final process design to ensure cost competitiveness with conventional reverse osmosis processes. © 2012 by the authors.
ISSN: 2073-4441

hal-01683200
https://hal.univ-antilles.fr/hal-01683200
DOI : 10.3390/w4030629