Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Well-dispersed iron oxide nanoparticles supported onto graphene oxide sheets (i.e. GO-Fe3O4 nanocomposite) were synthesised and used as heterogeneous Fenton-like catalyst for the degradation of Acid Orange 7 dye (AO7). The reaction was systematically investigated under various experimental conditions such as nanocomposite dosage, pH, temperature, oxidant and dye concentrations. Best results showed a fast 80% degradation in ∼20 min, whilst ∼98% of AO7 was successfully removed after 180 min of reaction time. The degradation kinetics of AO7 was most influenced by pH and temperature, and can be described by a pseudo-first-order reaction following the Langmuir-Hinshelwood mechanism. Analysis of the spent nanocomposite suggested that the phase of iron oxide nanoparticles remained unchanged whilst minor pore volume losses occurred via carbon deposition and/or re-stacking of GO sheets. © 2014 Elsevier Ltd.
ISSN: 2213-3437

hal-01683206
https://hal.univ-antilles.fr/hal-01683206
DOI : 10.1016/j.jece.2014.08.001

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Here we show that copper substitution in perovskite-type barium strontium cobalt copper oxide (BSCC) membranes confers extremely high oxygen fluxes well beyond the state of art, reaching 27.5 ml cm−2 min−1at 950 °C. A key feature of BSCC is the formation of a mixed matrix catalyst-perovskite membrane caused by the segregation of copper, leading to the formation of an intergranular network of copper-rich oxide between perovskite grains. BSCC membranes delivered pressure normalised oxygen flux (i.e. permeance) of up to 86 times higher, above pressure difference of 18 kPa, as compared to best perovskite membrane, BBSC, due to the catalytic effect of segregated copper oxide. Unlike conventional dual-phase membranes which contain ion and electron conducting phases, this work shows for the first time perovskite-type membranes consisting of a mixed matrix of oxygen ion/electron conducting (perovskite) and catalytic (copper oxide) phases, thus paving the way to the development of high performance membranes for oxygen separation from air for clean energy applications. © 2016 Elsevier B.V.
ISSN: 0376-7388

hal-01683219
https://hal.univ-antilles.fr/hal-01683219
DOI : 10.1016/j.memsci.2016.12.035

Éditeur(s) : HAL CCSD Royal Society of Chemistry
Résumé : International audience
Abstract View references (60)Here we show the long term performance at high temperatures of a multi-tube module containing 8 membranes in 4 parallel lines with a total of 545 cm 2 area. The membranes were prepared via thin film dip coating of cobalt oxide silica (CoO xSi) sol-gel on tubular alumina supports. A preliminary study found that the sol-gel containing 20 mol% cobalt oxide formed the best microporous structure with the highest surface area and pore volume. All resulting membranes delivered permeances of ∼1 × 10 -7 mol m -2 s -1 Pa -1 at 500 °C, indicating a high repeatability for the membrane fabrication process. The permselectivities of helium (He) and hydrogen (H 2) over carbon dioxide (CO 2) and nitrogen (N 2) increased from 10-20 at 100 °C to values close to 1000 at 500 °C. Additionally, the apparent energies of activation (E act) for the smaller kinetic diameter gases He and H 2 at 12.2 and 19.5 kJ mol -1 were high and contrary to the negative values for larger gases N 2 and CO 2 at -1.8 and -7.4 kJ mol -1. These remarkable results were attributed to the molecular sieving mechanism of the microporous silica which was enhanced by the embedding of cobalt oxide into the matrix, delivering structural control with an average pore size of 3 Å. The E act for H 2 permeance was higher than that of He, indicating that the cobalt oxide played an important role in H 2 transport. Two membrane lines performed exceptionally well for binary gas mixture processing with H 2 purity reaching values close to 100% in the permeate stream for argon (Ar) concentrations of up to 80% in the retentate stream. A major finding here is that the binary gas selectivity was independent of temperature, contrary to the permselectivity observed for single gas permeance. Further, the H 2 flow rate was greatly affected by the concentration of Ar in the mixture, while the temperature dependency played only a marginal role. In particular, competitive adsorption in the percolative pathways containing pore constrictions or bottlenecks of the anisotropic CoO xSi matrix allowed Ar to impede H 2 diffusion. Finally, the CoO xSi membranes proved thermally stable and robust for 2000 h of testing for various thermal cycles up to 500 °C. © The Royal Society of Chemistry 2012.
Energy & Environmental Science

hal-01683199
https://hal.univ-antilles.fr/hal-01683199
DOI : 10.1039/c2ee03247c

Éditeur(s) : HAL CCSD
Résumé : International audience
Many countries are legally obliged to embrace ecosystem-based approaches to fisheries management. Reductions in bycatch and physical habitat damage are now commonplace, but mitigating more sophisticated impacts associated with the ecological functions of target fisheries species are in their infancy. Here we model the impacts of a parrotfish fishery on the future state and resilience of Caribbean coral reefs, enabling us to view the tradeoff between harvest and ecosystem health. We find that the implementation of a simple and enforceable size restriction of >30 cm provides a win:win outcome in the short term, delivering both ecological and fisheries benefits and leading to increased yield and greater coral recovery rate for a given harvest rate. However, maintaining resilient coral reefs even until 2030 requires the addition of harvest limitations (<10% of virgin fishable biomass) to cope with a changing climate and induced coral disturbances, even in reefs that are relatively healthy today. Managing parrotfish is not a panacea for protecting coral reefs but can play a role in sustaining the health of reefs and high-quality habitat for reef fisheries.
http://hal.univ-reunion.fr/hal-01369752

hal-01369752
http://hal.univ-reunion.fr/hal-01369752
DOI : 10.1073/pnas.1601529113

Éditeur(s) : HAL CCSD Cambridge University Press (CUP)
Résumé : International audience
We studied the monogenean communities of 34 species of butterflyfish from the tropical Indo-West Pacific, identifying 13 dactylogyrid species (including two species that are presently undescribed). Monogenean assemblages differed significantly between host species in terms of taxonomic structure, intensity and prevalence. Parasite richness ranged from 0 (Chaetodon lunulatus) to 11 (C. auriga, C. citrinellus and C. lunula). Host specificity varied between the dactylogyrids species, being found on 2-29 of the 34 chaetodontid species examined. Sympatric butterflyfish species were typically parasitized by different combinations of dactylogyrid species, suggesting the existence of complex host-parasite interactions. We identified six clusters of butterflyfish species based on the similarities of their dactylogyrid communities. Dactylogyrid richness and diversity were not related to host size, diet specialization, depth range or phylogeny of butterflyfish species. However, there was a weak positive correlation between monogenean richness and diversity and host geographical range. Most communities of dactylogyrids were dominated by Haliotrema aurigae and H. angelopterum, indicating the importance of the genus Haliotrema in shaping monogenean communities of butterflyfishes. This study casts light on the structure of the monogenean communities of butterflyfishes, suggesting that the diversity and complexity of community structures arises from a combination of host species-specific parameters.
ISSN: 0031-1820

hal-01380679
https://hal-univ-perp.archives-ouvertes.fr/hal-01380679
DOI : 10.1017/S0031182016001463

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Geographical distribution of parasite species can provide insights into the evolution and diversity of parasiticcommunities. Biogeography of marine parasites is poorly known, especially because it requires anunderstanding of host-parasite interactions, information that is rare, especially over large spatial scales.Here, we have studied the biogeographical patterns of dactylogyrid parasites of chaetodontids, one of themost well-studied fish families, in the tropical Indo-west Pacific region. Dactylogyrid parasites were collectedfrom gills of 34 butterflyfish species (n = 560) at nine localities within an approximate area of62 million km2. Thirteen dactylogyrid species were identified, with richness ranging from 6 to 12 speciesat individual localities. Most dactylogyrid communities were dominated by Haliotrema angelopterum orHaliotrema aurigae, for which relative abundance was negatively correlated (q = !0.59). Parasite richnessand diversity were highest in French Polynesia and the Great Barrier Reef (Australia) and lowest in Palau.Three biogeographic regions were identified based on dactylogyrid dissimilarities: French Polynesia,characterised by the dominance of H. angelopterum, the western Pacific region dominated by H. aurigae,and Ningaloo Reef (Australia), dominated by Euryhaliotrema berenguelae. Structure of host assemblageswas the main factor explaining the dissimilarity (turnover and nestedness components of the Bray-Curtis dissimilarity and overall Bray-Curtis dissimilarity) of parasite communities between localities,while environment was only significant in the turnover of parasite communities and overall dissimilarity.Spatial structure of localities explained only 10% of the turnover of parasite communities. The interactionof the three factors (host assemblages, environment and spatial structure), however, explained the highestamounts of variance of the dactylogyrid communities, indicating a strong colinearity between the factors.Our findings show that spatial arrangement of chaetodontid dactylogyrids in the tropical Indo-westPacific is primarily characterised by the turnover of the main Haliotrema spp., which is mainly explainedby the structure of host assemblages.
ISSN: 0020-7519

hal-01562156
https://hal-univ-perp.archives-ouvertes.fr/hal-01562156
DOI : 10.1016/j.ijpara.2017.01.006

Éditeur(s) : HAL CCSD
Résumé : International audience
Abstract View references (38)This work presents a facile, scalable method for the fabrication of graphene oxide-iron oxide (GO-Fe3O4) nanocomposites produced by co-precipitation of iron ions onto the GO surfaces in basic aqueous media. FTIR and XRD characterisation suggests that Fe3O4 was chemically anchored to the GO sheets, possibly via the carboxyl and hydroxyl groups. Small GO loadings of 0.5 and 1 wt% were not sufficient to alter the Fe3O4 structures. However, increasing the GO loading to 5 and 10 wt% resulted in significant loss in pore volume, thus suggesting the lamellar GO sheets decorated with Fe3O4 were assembling into GO-Fe3O4 nanocomposite stacks. It was found that the GO-Fe3O4 nanocomposites had an enhanced catalytic activity in the heterogeneous Fenton-like oxidation of Acid Orange 7 (AO7) compared to pure GO flat sheets and Fe3O4 nanoparticles. Interestingly, the GO-Fe3O4 nanocomposite with 5 wt% loading ratio exhibited the best catalytic activity with 76% degradation of AO7 dye observed within 90 min of reaction. This was attributed to the synergistic effect of GO by enriching the adsorbed AO7 molecules onto the nanocomposite to be further oxidised in the vicinities of active sites. This finding suggests the promising employment of GO-Fe3O4 nanocomposites in removing organic dyes from polluted water by heterogeneous Fenton-like reaction. © 2014 by American Scientific Publishers.
SCIENCE OF ADVANCED MATERIALS

hal-01683207
https://hal.univ-antilles.fr/hal-01683207
DOI : 10.1166/sam.2014.1812

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Abstract The functionality or oxidation state of cobalt within a silica matrix can be tailored through the use of cationic surfactants and their halide counter ions during the sol-gel synthesis. Simply by adding surfactant we could significantly increase the amount of cobalt existing as Co3O4 within the silica from 44% to 77%, without varying the cobalt precursor concentration. However, once the surfactant to cobalt ratio exceeded 1, further addition resulted in an inhibitory mechanism whereby the altered pyrolysis of the surfactant decreased Co3O4 production. These findings have significant implications for the production of cobalt/silica composites where maximizing the functional Co3O4 phase remains the goal for a broad range of catalytic, sensing and materials applications.
ISSN: 2045-2322

hal-01683204
https://hal.univ-antilles.fr/hal-01683204
DOI : 10.1038/srep02449

Éditeur(s) : HAL CCSD Royal Society of Chemistry
Résumé : International audience
Owing to the electron donor-acceptor properties of GO, the active sites (≡Fe2+) of Fe3O4 are not oxidised (≡Fe3+) in the heterogeneous Fenton-like reaction. GO plays a sacrificial role via the oxidation of (C=C) carbon domains, and transferring electrons to Fe3O4. Therefore, GO-Fe3O4 confers superior catalytic efficiency, recyclability and longevity, otherwise not available in Fe3O4. © The Royal Society of Chemistry 2015.
ISSN: 1359-7345

hal-01683211
https://hal.univ-antilles.fr/hal-01683211
DOI : 10.1039/c5cc02292d

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
Exposure to disturbance is rarely considered in marine protected area planning. Typically, representing and replicating the habitat types present within protected areas is used to spread the risk of protecting frequently disturbed sites. This was the approach used during the 2004 re-zoning of the Great Barrier Reef Marine Park (GBRMP) via the Representative Areas Program. Over 10 years later, we examine whether the risk was spread by mapping exposure of coral reefs in the GBRMP to four disturbances that cause coral mortality: bleaching, tropical cyclones, crown-of-thorns starfish outbreaks, and freshwater inundation. Our objectives were to: (1) assess whether no-take areas include a range of disturbance regimes, and (2) identify coral reef areas with lower relative exposure. At least 13% and an average of 31% of reef locations in each of 11 exposure classes are included within no-take areas. A greater proportion of low-exposure areas are within no-take areas than high-exposure areas (34.2% vs. 28.3%). The results demonstrate the value of risk spreading when exposure data are not available while also showing that regularly assessing exposure increases capacity for adaptive, resilience-based reef management.
ISSN: 1755-263X

Droits : http://creativecommons.org/licenses/by/
hal-01225201
https://hal-univ-perp.archives-ouvertes.fr/hal-01225201
https://hal-univ-perp.archives-ouvertes.fr/hal-01225201/document
https://hal-univ-perp.archives-ouvertes.fr/hal-01225201/file/Maynard_et_al-2015-Conservation_Letters.pdf
DOI : 10.1111/conl.12198

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Carbonised template silica membranes were synthesised and investigated for water desalination for brackish (0.3wt%), sea water (3.5wt%) and brine (7.5wt%) NaCl solutions at temperatures range from 22 to 60°C. The membranes were prepared by a two-step base catalysed sol-gel method using tetraethyl orthosilicate TEOS as the silica precursor and triblock copolymer of Pluronic® P123 as the templating agent. The P123 silica membranes calcined under vacuum only produced high quality membranes by the interlayer-free method. The membranes were stable during testing of up to 250h under different thermal and salt concentration solutions, always delivering very high salt rejections >99.5%. It was found that by increasing the template concentration in the silica matrix from 5 to 50wt%, salt concentration polarisation was greatly reduced. As such, high water fluxes were measured up to 8.5kgm-2h-1 for brackish water and 6.6kgm-2h-1 for brine water. © 2014 Elsevier B.V.
ISSN: 0376-7388

hal-01683210
https://hal.univ-antilles.fr/hal-01683210
DOI : 10.1016/j.memsci.2014.10.026

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Mesoporous cobalt oxide silica matrices and membranes were successfully prepared using a dual acid-base catalysed sol-gel and interlayer-free approach for desalination applications. The effects of cobalt addition (0-35 mol%) on the structure-property relationship of the silica materials and membrane performance were systematically studied as a function of feed salt concentration (0.3-7.5 wt.% NaCl) and temperature (22-60 °C). As cobalt concentration increases beyond 5 mol%, the concentration of tricobalt tetroxide and proportion of silica mesopores were found to increase within the matrices. Silica membranes with high amount of tricobalt tetroxide (35 mol%) were found to be highly mesoporous with water fluxes of 20, 11.3 and 7.7 kg m-2 h-1 for the 0.3, 3.5 and 7.5 wt.% solutions at 60 °C, respectively, with >99.7% salt rejection at all times. This is attributed to the high pore volume (mesopores formation) and structural robustness of the silica network provided by the presence of tricobalt tetroxide. Even higher performance was achieved for low tricobalt tetroxide (mol%) silica membranes with water fluxes of 47.6 (0.3 wt.%) and 31.5 (3.5 wt.%) kg m-2 h-1 at 60 °C, respectively, though with reduced salt rejections of 90%. © 2015 Elsevier B.V.
ISSN: 0011-9164

hal-01683209
https://hal.univ-antilles.fr/hal-01683209
DOI : 10.1016/j.desal.2015.02.034

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
AimBiological invasions are major contributors to global change and native biodiversity decline. However, they are overlooked in marine conservation plans. Here, we examine for the first time the extent to which marine conservation planning research has addressed (or ignored) biological invasions. Furthermore, we explore the change of spatial priorities in conservation plans when different approaches are used to incorporate the presence and impacts of invasive species.LocationGlobal analysis with a focus on the Mediterranean Sea region.MethodsWe conducted a systematic literature review consisting of three steps: (1) article selection using a search engine, (2) abstract screening and (3) review of pertinent articles, which were identified in the second step. The information extracted included the scale and geographical location of each case study as well as the approach followed regarding invasive species. We also applied the software Marxan to produce and compare conservation plans for the Mediterranean Sea that either protect, or avoid areas impacted by invasives, or ignore the issue. One case study focused on the protection of critical habitats, and the other on endemic fish species.ResultsWe found that of 119 papers on marine spatial plans in specific biogeographic regions, only three (2.5%) explicitly took into account invasive species. When comparing the different conservation plans for each case study, we found that the majority of selected sites for protection (ca. 80%) changed in the critical habitat case study, while this proportion was lower but substantial (27%) in the endemic fish species case study.Main conclusionsBiological invasions are being widely disregarded when planning for conservation in the marine environment across local to global scales. More explicit consideration of biological invasions can significantly alter spatial conservation priorities. Future conservation plans should explicitly account for biological invasions to optimize the selection of marine protected areas.
ISSN: 1366-9516

hal-01431351
https://hal-univ-perp.archives-ouvertes.fr/hal-01431351
DOI : 10.1111/ddi.12491

Éditeur(s) : HAL CCSD Wiley Open Access
Résumé : Biodiversity continues to decline in the face of increasing anthropogenic pressures such as habitat destruction, exploitation, pollution and introduction of alien species. Existing global databases of species' threat status or population time series are dominated by charismatic species. The collation of datasets with broad taxonomic and biogeographic extents, and that support computation of a range of biodiversity indicators, is necessary to enable better understanding of historical declines and to project - and avert - future declines. We describe and assess a new database of more than 1.6 million samples from 78 countries representing over 28,000 species, collated from existing spatial comparisons of local-scale biodiversity exposed to different intensities and types of anthropogenic pressures, from terrestrial sites around the world. The database contains measurements taken in 208 (of 814) ecoregions, 13 (of 14) biomes, 25 (of 35) biodiversity hotspots and 16 (of 17) megadiverse countries. The database contains more than 1% of the total number of all species described, and more than 1% of the described species within many taxonomic groups - including flowering plants, gymnosperms, birds, mammals, reptiles, amphibians, beetles, lepidopterans and hymenopterans. The dataset, which is still being added to, is therefore already considerably larger and more representative than those used by previous quantitative models of biodiversity trends and responses. The database is being assembled as part of the PREDICTS project (Projecting Responses of Ecological Diversity In Changing Terrestrial Systems - ). We make site-level summary data available alongside this article. The full database will be publicly available in 2015.
ISSN: 2045-7758

hal-01204216
https://hal.archives-ouvertes.fr/hal-01204216
DOI : 10.1002/ece3.1303
PRODINRA : 280886

Éditeur(s) : HAL CCSD MDPI AG, Basel, Switzerland
Résumé : International audience
Abstract View references (46)This work shows the preparation of silica membranes by a two-step sol-gel method using tetraethyl orthosilicate in ethanolic solution by employing nitric acid and ammonia as co-catalysts. The sols prepared in pH 6 resulted in the lowest concentration of silanol (Si-OH) species to improve hydrostability and the optimized conditions for film coating. The membrane was tested to desalinate 0.3-15 wt % synthetic sodium chloride (NaCl) solutions at a feed temperature of 22 °C followed by long term membrane performance of up to 250 h in 3.5 wt % NaCl solution. Results show that the water flux (and salt rejection) decrease with increasing salt concentration delivering an average value of 9.5 kg m-2 h-1 (99.6%) and 1.55 kg m-2 h-1 (89.2%) from the 0.3 and 15 wt % saline feed solutions, respectively. Furthermore, the permeate salt concentration was measured to be less than 600 ppm for testing conditions up to 5 wt % saline feed solutions, achieving below the recommended standard for potable water. Long term stability shows that the membrane performance in water flux was stable for up to 150 h, and slightly reduced from thereon, possibly due to the blockage of large hydrated ions in the micropore constrictions of the silica matrix. However, the integrity of the silica matrix was not affected by the long term testing as excellent salt rejection of >99% was maintained for over 250 h. © 2013 by the authors; licensee MDPI, Basel, Switzerland.
ISSN: 2077-0375

hal-01683203
https://hal.univ-antilles.fr/hal-01683203
DOI : 10.3390/membranes3030136

Éditeur(s) : HAL CCSD
Résumé : International audience
In this work, a series of zinc partially substituted magnetite nanoparticles (Fe3-xZnxO4, 0 ≤ x ≤ 0.4), were synthesised through a facile precipitation-oxidation method. The partial substitution of zinc into the magnetite (Fe3O4) structure was confirmed by the collective findings of nitrogen sorption, XRD and TG-DTG analysis. It was found that the partial substitution of zinc slightly changed the textural properties of the resultant Fe3-xZnxO4 nanoparticles. From the XRD analysis, there was no visible formation of secondary phase or impurity peaks in the nanoparticles. These findings indicated the partial substitution of zinc into the Fe3O4 crystal structure with a good dispersion within the Fe3O4 matrix. © 2016 Author(s).
1st International Conference on Advanced Science,
Penang, Malaysia

hal-01683217
https://hal.univ-antilles.fr/hal-01683217

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Abstract View references (45)Graphene oxide-iron oxide (GO-Fe3O4) nanocomposites were synthesised by co-precipitating iron salts onto GO sheets in basic solution. The results showed that formation of two distinct structures was dependent upon the GO loading. The first structure corresponds to a low GO loading up to 10wt%, associated with the beneficial intercalation of GO within Fe3O4nanoparticles and resulting in higher surface area up to 409m2g-1. High GO loading beyond 10 wt% led to the aggregation of Fe3O4 nanoparticles and the undesirable stacking of GO sheets. The presence of strong interfacial interactions (Fe-O-C bonds) between both components at low GO loading lead to 20% higher degradation of Acid Orange 7 than the Fe3O4 nanoparticles in heterogeneous Fenton-like reaction. This behaviour was attributed to synergistic structural and functional effect of the combined GO and Fe3O4 nanoparticles.
ISSN: 2045-2322

hal-01683208
https://hal.univ-antilles.fr/hal-01683208
DOI : 10.1038/srep04594

Éditeur(s) : HAL CCSD
Résumé : International audience
Cumulative human impacts have led to the degradation of marine ecosystems and thedecline of biodiversity in the European and contiguous seas. Effective conservationmeasures are urgently needed to reverse these trends. Conservation must entail societalchoices, underpinned by human values and worldviews that differ between the countriesbordering these seas. Social, economic and political heterogeneity adds to the challenge ofbalancing conservation with sustainable use of the seas. Comprehensive macro-regionalcoordination is needed to ensure effective conservation of marine ecosystems andbiodiversity of this region. Under the European Union Horizon 2020 framework programme,the MarCons COST action aims to promote collaborative research to support marinemanagement, conservation planning and policy development. This will be achieved bydeveloping novel methods and tools to close knowledge gaps and advance marineconservation science. This action will provide support for the development of macro-regional and national policies through six key actions: to develop tools to analysecumulative human impacts; to identify critical scientific and technical gaps in conservationefforts; to improve the resilience of the marine environment to global change and biologicalinvasions; to develop frameworks for integrated conservation planning across terrestrial,freshwater, and marine environments; to coordinate marine conservation policy acrossnational boundaries; and to identify effective governance approaches for marine protectedarea management. Achieving the objectives of these actions will facilitate the integration ofmarine conservation policy into macro-regional maritime spatial planning agendas for theEuropean and contiguous seas, thereby offsetting the loss of biodiversity and ecosystemservices in this region.
Research Ideas and Outcomes

hal-01474085
https://hal-univ-perp.archives-ouvertes.fr/hal-01474085
https://hal-univ-perp.archives-ouvertes.fr/hal-01474085/document
https://hal-univ-perp.archives-ouvertes.fr/hal-01474085/file/RIO_article_11884.pdf
DOI : 10.3897/rio.3.e11884

Éditeur(s) : HAL CCSD Royal Society of Chemistry
Résumé : International audience
A series of graphene oxide (GO) and zinc partially substituted magnetite GO-Fe1-xZnxOy (0 ≤ x ≤ 0.285) catalysts were synthesised through a precipitation-oxidation method. The rate constants for the degradation of acid orange seven (AO7) proceeded at a significant faster rate under UV-irradiation (up to 670%) than the conventional heterogeneous Fenton-like reaction. The resultant catalysts were mesoporous, so there was no mass transfer limitation for AO7 to access active sites in the catalysts. Further, maximum increases of rate constant up to 220% occurred as the zinc molar concentration increased from x = 0 to x = 0.159. GO enhanced to incorporation of zinc into the combined metal oxide, whilst zinc limited crystal growth, thus forming smaller crystallite sizes. These features proved to be essential for the improved catalytic activity of the resultant catalysts. The optimised zinc molar value at x = 0.159 delivered the best catalytic activity. © The Royal Society of Chemistry 2016.
ISSN: 2046-2069

hal-01683215
https://hal.univ-antilles.fr/hal-01683215
DOI : 10.1039/c6ra04068c

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This work shows the preparation and separation performance assessment of carbon membranes derived from phenolic resin by a vacuum-assisted method and carbonisation in an inert atmosphere. The vacuum time played an important role in tailoring the structure of the membranes. For instance, pore volumes and surface areas increased from 0.81 and 834 to 2.2 cm3g−1and 1910 m2g−1, respectively, as the vacuum time exposure increased from 0 to 1200 s. The significant structural changes correlated very well with water permeation, as fluxes increased by 91% as the vacuum time increased from 0 to 1200 s reaching up to 169 L m−2h−1at 5 bar. Molecular weight cut-off tests showed no rejection for the smaller glucose and sucrose molecules, though this increased to ~ 80% and full rejection for 36 kDa and 400 kDa polyvinyl pyrrolidine. Interestingly, FTIR spectra showed that the peaks of C–H stretching vibration (2800–3200 cm−1) and C–O stretching (1030 cm−1) became more pronounced as a function of increasing vacuum time, strongly suggesting that the use of vacuum further assisted in the polycondensation of phenolic oligomers. Based on these outcomes, a cluster to cluster model is proposed, whereby vacuum application promoted crosslinking reactions of the phenolic resin, creating microporous regions within the clusters, and mesoporous regions between the clusters. © 2016 Elsevier B.V
ISSN: 0376-7388

hal-01683220
https://hal.univ-antilles.fr/hal-01683220
DOI : 10.1016/j.memsci.2016.11.002