Éditeur(s) : HAL CCSD De Gruyter
Résumé :  
Experimental results are presented with single nail joints of gonfolo rose which were loaded at different grain angles and compared to results obtained by Eurocode V. A wide range of embedding strength tests was conducted. The embedding behaviour across the grain was also investigated with a specific test apparatus. The results were analysed and modelled in terms of strength. Initial loading and unloading stiffness of the timber have been taken into account. The embedment strength of the nails varied according to the angle between the direction of loading and that to the grain. This work is part of a larger research project to establish a computer program for the prediction of stiffness and limit strengths of all timber-to-timber and timber-to-steel joints.
ISSN: 0018-3830

hal-01032183
https://hal.archives-ouvertes.fr/hal-01032183
DOI : 10.1515/HF.2008.013

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
The data available in the literature concerning wood cutting forces permit to build models or to simulate the main wood machining processes (milling, sawing, peeling etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimize cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: (1) providing data to optimise the settings for a given operation (batch approach) and (2) building predictive models that could be the basis of an online control systems for the machining processes (interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With potential industrial applications in focus, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Though not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technologic knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003/document
https://hal.archives-ouvertes.fr/hal-00876003/file/LABOMAP_Holzforschung_2009_denaud.pdf
ENSAM : http://hdl.handle.net/10985/7419

Éditeur(s) : HAL CCSD De Gruyter
Résumé : COST Action E35 : Fracture mechanics and micromechanics of wood and wood composites with regard to wood machining
The data available in the literature concerning wood cutting forces permits to build models or to simulate the main wood machining processes ( milling, sawing, peeling, etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimise cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: ( 1) providing data to optimise the settings for a given operation ( batch approach), and ( 2) building predictive models that could be the basis of an online control system for the machining processes ( interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With a focus on potential industrial applications, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Although not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technological knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-01032121
https://hal.archives-ouvertes.fr/hal-01032121
DOI : 10.1515/HF.2009.014