Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context: Woodcutting is a very old technology but scientific research is scarce on the subject. In the last 50 years much work on basic mechanisms as well as industrial processes has been done in France. Aims: The specific nature of wood introduces strong differences between wood and metal cutting processes. The paper focuses on French teams' contributions. Results: The basic aspects of the tool–material interaction for different basic modes in woodcutting are highlighted. In primary conversion such as sawing, veneer cutting or green wood chipping, huge progress comes from automation and the possibility of linking the process to log and product quality through new sensors. In secondary processing much has been done on the links between the cutting process, surface qualification and the properties of these surfaces for further processing, such as gluing or coating. Tool wear depends on the cutting process, timber quality, and species. Trade-offs are required in tool technology and coating technologies may improve tool life. Conclusion: A large amount of knowledge and innovation has come from 50 years of worldwide research effort, with France being particularly active in this period. The transfer of skills from metals cutting industry was often a key, but much is needed to move closer to both metal cutting sector and woodcutting skills among craftsmen.
ISSN: 1286-4560

hal-01135156
https://hal.archives-ouvertes.fr/hal-01135156
https://hal.archives-ouvertes.fr/hal-01135156/document
https://hal.archives-ouvertes.fr/hal-01135156/file/Wood_machining_focus_French_research_Thibaut_al_2015.pdf
DOI : 10.1007/s13595-015-0460-2

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
The data available in the literature concerning wood cutting forces permit to build models or to simulate the main wood machining processes (milling, sawing, peeling etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimize cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: (1) providing data to optimise the settings for a given operation (batch approach) and (2) building predictive models that could be the basis of an online control systems for the machining processes (interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With potential industrial applications in focus, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Though not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technologic knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003/document
https://hal.archives-ouvertes.fr/hal-00876003/file/LABOMAP_Holzforschung_2009_denaud.pdf
ENSAM : http://hdl.handle.net/10985/7419

Éditeur(s) : HAL CCSD De Gruyter
Résumé : COST Action E35 : Fracture mechanics and micromechanics of wood and wood composites with regard to wood machining
The data available in the literature concerning wood cutting forces permits to build models or to simulate the main wood machining processes ( milling, sawing, peeling, etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimise cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: ( 1) providing data to optimise the settings for a given operation ( batch approach), and ( 2) building predictive models that could be the basis of an online control system for the machining processes ( interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With a focus on potential industrial applications, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Although not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technological knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-01032121
https://hal.archives-ouvertes.fr/hal-01032121
DOI : 10.1515/HF.2009.014