Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Variation of dead wood decay rates among tropical trees remains one source of uncertainty in global models of the carbon cycle. Taking advantage of a broad forest plot network surveyed for tree mortality over a 23-year period, we measured the remaining fraction of boles from 367 dead trees from 26 neotropical species widely varying in wood density (0.23–1.24 g cm-3) and tree circumference at death time (31.5–272.0 cm). We modeled decay rates within a Bayesian framework assuming a first order differential equation to model the decomposition process and tested for the effects of forest management (selective logging vs. unexploited), of mode of death (standing vs. downed) and of topographical levels (bottomlands vs. hillsides vs. hilltops) on wood decay rates. The general decay model predicts the observed remaining fraction of dead wood (R2 = 60%) with only two biological predictors: tree circumference at death time and wood specific density. Neither selective logging nor local topography had a differential effect on wood decay rates. Including the mode of death into the model revealed thatstanding dead trees decomposed faster than downed dead trees, but the gain of model accuracy remains rather marginal. Overall, these results suggest that the release of carbon from tropical dead trees to the atmosphere can be simply estimated using tree circumference at death time and wood density.
ISSN: 0029-8549

hal-01094187
https://hal-agroparistech.archives-ouvertes.fr/hal-01094187
DOI : 10.1007/s00442-010-1602-8

Éditeur(s) : HAL CCSD
Résumé : International audience
Radiocarbon dating and "old wood problem" in the Antilles : the state of the artAmong the many effects that may distort the interpretation of radiocarbon dates are those for which the age of the archaeological event is different from the radiocarbon age of the sample or "14C event" age. This type of problem arises in many cases, notably in the "old wood effect”, and occurs in various regions of the world where very long-lived trees species are common. In the Caribbean anthracological studies indicate a very high frequency of some indigenous centuries-old species such as Guaiacum, Guaiacum officinale L. However the absence of tree-ring data in humid tropical zones deprives us of an accurate inventory of long-lived species and especially the assessment of their longevity. Here we present measurements which enable us to estimate the longevity of archaeological Guaiacum wood posts. They highlight a gap of several centuries between wood from the outer edge and the heart of the tree. This example illustrates the additional uncertainty that can result from dating archeological events when dates are realized on unidentified botanical species from which the area that was sampled is unknown. Another source of error could arise from the use of rot-proof dead wood as fuel if we take into consideration that major hurricanes can produce large amounts of dead wood that may be collected for decades, even centuries. To improve chronometric data used in archaeological interpretations, it is necessary to ensure the quality of the dating process by following a protocol similar to those used in other regions of the world based on a better understanding of the material to be dated by preliminary identifications of wood samples: species, anatomical part, wood moisture content (unseasoned or seasoned).
Radiocarbono y "problema madera vieja", que data de las Antillas: estado del arteEntre los muchos efectos que pueden distorsionar la interpretación de fechas de radiocarbono, destacan aquellos para los que la edad de la prueba arqueológica es diferente de la edad de radiocarbono de la muestra, o la edad del "evento de radiocarbono." Este tipo de problema se presenta en muchos casos, especialmente uno llamado "efecto madera vieja." Esto se refleja en diversas regiones del mundo donde las especies de plantas de mucha longevidad son comunes. En el Caribe, los estudios antracológicos disponibles indican una muy alta frecuencia de algunas especies autóctonas como el guayaco, Guaiacum officinale L. Sin embargo, la casi ausencia de datos de anillos de árboles en los trópicos húmedos, nos impide realizar un inventario exacto de especies de mucha longevidad y sobre todo la evaluación de la longevidad. Algunas de las pruebas presentadas aquí permitieron una estimación de la longevidad de de unos postes de guayaco de origen arqueológico. Ponen de manifiesto una brecha de varios siglos entre las partes externas y el corazón del tronco. Este ejemplo ilustra la aparición de una incertidumbre adicional en la datación de los eventos arqueológicos cuando no conocemos la especie botánica y tampoco la zona de la muestra en el árbol. Otra fuente de error puede surgir de la utilización de la madera muerta de calidad duradera como combustible ya que los grandes huracanes pueden producir grandes cantidades de madera muerta, que puede ser requerida durante décadas, incluso siglos. Para mejorar los datos cronométricos utilizados en interpretaciones arqueológicas, es necesario asegurarse de la calidad de las fechas, y por lo tanto seguir un protocolo similar a los utilizados en otras regiones fundado en una mejor comprensión de los elementos: especie, parte anatómica, humedad de la madera usada (verde o seco).
Parmi les nombreux effets susceptibles de fausser l’interprétation des datations par le radiocarbone, figurent ceux pour lesquels l’âge de l’événement archéologique est différent de l’âge radiocarbone de l’échantillon, ou âge de l’« événement radiocarbone ». Ce type de problème se pose dans de nombreux cas, en particulier celui dénommé « effet vieux bois ». Cette question est prise en compte dans diverses régions du monde où des espèces végétales très longévives sont fréquentes. Dans les Antilles les études anthracologiques disponibles indiquent une fréquence très importante de certaines espèces autochtones multiséculaires dont le gaïac, Guaiacum officinale L.. Cependant, la quasi absence de données dendrochronologiques dans la zone tropicale humide, nous privent d’un inventaire précis des espèces longévives et surtout de l’évaluation de leur longévité. Quelques tests présentés ici ont permis une estimation de la longévité de poteaux d’origine archéologique en bois de gaïac. Ils mettent en évidence un décalage de plusieurs siècles entre les parties externes et le cœur du tronc. Cet exemple illustre l’apparition d’une incertitude supplémentaire dans la datation de l’événement archéologique lorsque que l’on ne connaît ni l’espèce botanique ni la zone de prélèvement dans l’arbre. Une autre source d’erreur pourrait provenir de l’utilisation de bois mort de qualité très durable comme combustible, sachant que les grands cyclones peuvent produire d’importantes quantités de bois mort susceptible d’être récolté pendant des décennies, voire des siècles. Afin d’améliorer les données chronologiques utilisées dans les interprétations archéologiques, il apparaît nécessaire de s’assurer de la qualité des datations, et donc de suivre un protocole similaire à ceux utilisés dans d’autres régions basé sur une meilleure connaissance des éléments datés : espèce, partie anatomique, humidité du bois utilisé (vert ou sec).
Puerto Rico 2013 : Actas del 25to Congreso Internacional de Arqueología del Caribe - Proceeding of the 25th International Congress for Caribbean Archeology - Comptes rendus des communications du 25e Congrés International de l'Archéologie de la Caraïbe
San-Juan, Puerto Rico

hal-01198567
https://hal.archives-ouvertes.fr/hal-01198567
https://hal.archives-ouvertes.fr/hal-01198567/document
https://hal.archives-ouvertes.fr/hal-01198567/file/Stouvenot%20et%20al.%202015.%20Effet%20vieux%20bois%20radiocarbone%20Antilles%20HD.pdf

Éditeur(s) : HAL CCSD
Résumé : Diffusion du document : INRA Antilles-Guyane, UMR ECOFOG, 97387 Kourou, Guyane (France) Diplôme : Master Recherche
il s'agit d'un type de produit dont les métadonnées ne correspondent pas aux métadonnées attendues dans les autres types de produit : DISSERTATION
La forêt tropicale guyanaise comporte entre 200 et 300 espèces d'arbres par hectare, alors qu'une forêt tempérée en compte environ une quinzaine. Les forêts tropicales humides sont des écosystèmes qui recèlent une des plus grandes biodiversités de la planète où les interactions entre les espèces et le milieu environnant atteignent des degrés de complexité élevés. Les arbres développent ainsi des stratégies souvent différentes, notamment celle du contrefil que nous avons cherché à décrire et à caractériser, lors de ce stage de Master 2ème année. Cette structure particulière du bois se retrouve dans une proportion importante dans les forêts tropicales. Elle consiste en une alternance d'hélices en S puis en Z de l'orientation longitudinale des fibres. Le stage s'est déroulé en grande partie en Guyane française, au sein de l'UMR « Ecologie des Forêts de Guyane » sur le site de Paracaïbo (Kourou). La première phase a été la prospection et la description du contrefil sur différentes espèces. Nous nous sommes ensuite intéressés au comportement mécanique en flexion statique et dynamique à différentes échelles. Enfin, au Laboratoire de Mécanique et Génie Civil de Montpellier, nous avons réalisé des mesures de l'angle des micros fibrilles afin de déterminer son évolution en fonction de l'angle du fil. Ainsi, prenant en compte les différentes échelles de description, nous avons mis au point un modèle permettant de prédire le comportement d'une poutre contre filée en flexion, connaissant la répartition du contrefil dans la section, la densité, et le module d'élasticité longitudinal orienté selon le fil du bois.
https://hal.archives-ouvertes.fr/hal-01189254

hal-01189254
https://hal.archives-ouvertes.fr/hal-01189254
PRODINRA : 19939

Éditeur(s) : HAL CCSD Walter de Gruyter
Résumé :  
A method for measuring shrinkage resulting from drying in the three anisotropic directions is developed and tested. Measurements are performed on sawn discs, a technique which simplifies preparation and enables large numbers of measurements. Shrinkage values can be represented as a map of the disc surface. The results indicate that comparisons between shrinkage distribution and tension wood distribution on the discs show a clear relationship and can be measured with relatively high accuracy in reference to the "shrinkage map". In the long term, this method could be useful in the timber industry as a means for choosing the direction in which logs are cut depending on their type of wood composition.
Holzforschung

hal-01032055
https://hal.archives-ouvertes.fr/hal-01032055
DOI : 10.1515/HF.2003.100

Éditeur(s) : HAL CCSD
Résumé :  
Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rain forest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood, and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-01032051
https://hal.archives-ouvertes.fr/hal-01032051

Éditeur(s) : HAL CCSD Public Library of Science
Résumé : International audience
Challenging evaluation of tropical forest biodiversity requires the reporting of taxonomic diversity but also the systematic characterization of wood properties in order to discover new promising species for timber industry. Among wood properties, the dimensional stability is regarded as a major technological characteristic to validate whether a wood species is adapted to commercial uses. Cell structure and organization are known to influence the drying shrinkage making wood density and microfibrils angle markers of choice to predict wood dimensional stability. On the contrary the role of wood extractive content remains unclear. This work focuses on the fast-growing tropical species Bagassa guianensis and we report herein a correlation between heartwood drying shrinkage and extractive content. Chemical extractions and shrinkage experiments were performed on separate wood twin samples to better evaluate correctly how secondary metabolites influence the wood shrinkage behaviour. Extractive content were qualitatively and quantitatively analysed using HPLC and NMR spectroscopy. We found that B guianensis heartwood has a homogeneous low shrinkage along its radius that could not be explained only by its basic density. In fact the low drying shrinkage is correlated to the high extractive content and a corrected model to improve the prediction of wood dimensional stability is presented. Additionally NMR experiments conducted on sapwood and heartwood extracts demonstrate that secondary metabolites biosynthesis occurs in sapwood thus revealing B. guianensis as a Juglans-Type heartwood formation. This work demonstrates that B. guianensis, a fast-growing species associated with high durability and high dimensional stability, is a good candidate for lumber production and commercial purposes.
ISSN: 1932-6203

hal-01392725
https://hal.archives-ouvertes.fr/hal-01392725
https://hal.archives-ouvertes.fr/hal-01392725/document
https://hal.archives-ouvertes.fr/hal-01392725/file/2016_BossuBeaucheneEstevezDuplaisClair_PlosOne_WoodDimentionalStabilityAndSecondaryMetabolites.pdf
DOI : 10.1371/journal.pone.0150777.s005

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The study of decay resistance in wood is of interest for wood end-users but also for the global carbon balance since wood biodegradation is a key driver of forest ecosystem functioning through its impacts on carbon and nutrient cycling. We studied the density and wood extractive contents in order to understand decay resistance against soil microflora after 90 days exposure of sapwood and heartwood from three Neotropical wood species known for their decay resistance: Bocoa prouacensis, Vouacapoua americana, Inga alba. Decay resistance was correlated with density more than wood extractive content. The results highlighted different decay resistance strategies. In B. prouacensis, both sapwood and heartwood were highly resistant due to the high density and high content of antifungal wood extractives. In V. americana heartwood, decay resistance was due to the high synergistic-acting wood extractive content. Conversely, with the least dense wood species I. alba, we found that decay resistance was due to the antifungal wood extractives synthesized early in the sapwood. In conclusion, we showed that the three wood species with the same level of heartwood decay resistance performance had different decay resistance strategies according to the anatomic and defensive wood traits.
ISSN: 0964-8305

hal-01321162
https://hal.archives-ouvertes.fr/hal-01321162
https://hal.archives-ouvertes.fr/hal-01321162/document
https://hal.archives-ouvertes.fr/hal-01321162/file/Art_Amusant_al_Diversity_decay_resistance_strategies_Int.Biodet.Biodegr._2014.pdf
DOI : 10.1016/j.ibiod.2014.06.012

Éditeur(s) : HAL CCSD Ecole nationale du génie rural
Résumé :  
Les bois tropicaux, et en particulier les bois de Guyane, témoignent de la biodiversité des forêts denses humides. Les atouts et contraintes liés à cette diversité sont présentés ainsi que la façon objective de classer les espèces ou essences par rapport à des critères de qualité. La variabilité de la qualité des bois est illustrée à travers quelques exemples : la qualité des arbres sur pied, la qualité non constante de l'Angélique (Dicorynia guianensis), les troncs cannelés du Wacapou (Vouacapoua americana), les différences entre deux espèces d'Eperua Spp.. La conclusion porte sur la petite filière-bois guyanaise, ses difficultés et les enjeux à relever.
ISSN: 0035-2829

hal-01031808
https://hal.archives-ouvertes.fr/hal-01031808

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
A feasibility study of glulam was carried out in French Guiana using local wood species. The aim was to determine gluing parameters affording satisfactory behaviour to manufactured glulam in a tropical climate. Three abundant wood species, with special properties, were selected for the study and Resorcinol-Phenol-Formaldehyde resin was used for bonding. Three industrial parameters were considered: adhesive spread rate, closed assembly time and gluing pressure. Delamination and shearing tests were carried outin accordance with European Standards. The tests revealed the influence of wood properties and manufacturing parameters on joint resistance. In fact, the results showed that specific gravity and the shrinkage coefficientgreatly influenced the gluing step. Indeed, wood with a medium specific gravity needed more adhesive and more pressure than wood with a high specific gravity. In addition, planning and lamella thicknesswere found to affect glue joint resistance.
ISSN: 0018-3768

hal-00856933
https://hal.archives-ouvertes.fr/hal-00856933
https://hal.archives-ouvertes.fr/hal-00856933/document
https://hal.archives-ouvertes.fr/hal-00856933/file/Feasibility_glued_laminated_timber_Bourreau_al.pdf

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé :  
absent
ISSN: 1286-4560

hal-01032143
https://hal.archives-ouvertes.fr/hal-01032143
DOI : 10.1051/forest:2008061

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context: Woodcutting is a very old technology but scientific research is scarce on the subject. In the last 50 years much work on basic mechanisms as well as industrial processes has been done in France. Aims: The specific nature of wood introduces strong differences between wood and metal cutting processes. The paper focuses on French teams' contributions. Results: The basic aspects of the tool–material interaction for different basic modes in woodcutting are highlighted. In primary conversion such as sawing, veneer cutting or green wood chipping, huge progress comes from automation and the possibility of linking the process to log and product quality through new sensors. In secondary processing much has been done on the links between the cutting process, surface qualification and the properties of these surfaces for further processing, such as gluing or coating. Tool wear depends on the cutting process, timber quality, and species. Trade-offs are required in tool technology and coating technologies may improve tool life. Conclusion: A large amount of knowledge and innovation has come from 50 years of worldwide research effort, with France being particularly active in this period. The transfer of skills from metals cutting industry was often a key, but much is needed to move closer to both metal cutting sector and woodcutting skills among craftsmen.
ISSN: 1286-4560

hal-01135156
https://hal.archives-ouvertes.fr/hal-01135156
https://hal.archives-ouvertes.fr/hal-01135156/document
https://hal.archives-ouvertes.fr/hal-01135156/file/Wood_machining_focus_French_research_Thibaut_al_2015.pdf
DOI : 10.1007/s13595-015-0460-2

Éditeur(s) : HAL CCSD Botanical Society of America
Résumé :  
International audience
The different hypotheses about buttress function and formation mainly involve mechanical theory. Forces were applied to two trees of Sloanea spp., a tropical genus that develops typical thin buttresses, and the three-dimensional strains were measured at different parts of the trunk base. Risks of failure were greater on the buttress sides, where shear and tangential stresses are greater, not on the ridges, in spite of high longitudinal (parallel to the grain) stresses. A simple beam model, computed from the second moment of area of digitized cross sections, is consistent with longitudinal strain variations but cannot predict accurately variations with height. Patterns of longitudinal strain variation along ridges are very different in the two individuals, owing to a pronounced lateral curvature in one specimen. The constant stress hypothesis is discussed based on these results. Without chronological data during the development of the tree, it cannot be proved that buttress formation is activated by stress or strain.
ISSN: 0002-9122

hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155
https://hal.archives-ouvertes.fr/hal-01032155/document
https://hal.archives-ouvertes.fr/hal-01032155/file/Biomechanics_buttressed_trees_Clair_al_2003.pdf
DOI : 10.3732/ajb.90.9.1349

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called G-layer, in the fibre wall. The structure of G-layer has been recently described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2 to 50 nm). This led us to revisit the concept of G-layer that was until now only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with typical thick G-layer while it is much less with thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without G-layer is as low as in normal wood. Not depending on the amount of pores, the pore sizes distribution are always centred around 6-12 nm. These results suggest that, among species producing fibres with G-layer, large structural differences of G-layer exist between species
ISSN: 0022-0957

hal-00387861
https://hal.archives-ouvertes.fr/hal-00387861
DOI : 10.1093/jxp/erp133

Éditeur(s) : HAL CCSD
Résumé : International audience
Over the past decade, much attention has been devoted to the development of forest biomass estimation methods at a stand scale, leading to the establishment of allometric models (Chave et al., 2014). These allometric equations use a unique wood specific gravity value (WSG) per species, but neglect the within tree variations of WSG found by others (Wiemann & Williamson, 1989).The main objectives of this study are (1) to illustrate the diversity of radial (from pith to bark) and longitudinal (from bottom to top) patterns of WSG variation within and between species, (2) to highlight different trends of WSG radial variations and the possible misinterpretations of these trends due to the effect of heartwood and (3) to link these variations and patterns to the successional status of the species (from pioneer to sciaphilic species).We sampled 33 small trees (10 Wood sciences underpinning tropical ecology and management. International closing symposium of the XYLAREDD project.
Tervuren, Belgium

hal-01188894
https://hal-sde.archives-ouvertes.fr/hal-01188894

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Extractives that provide natural resistance to Bagassa guianensis Aubl. heartwood were examined. Soil-bed tests showed that the B. guianensis heartwood resistance was significantly reduced after ethyl acetate extraction, whereas methanol and especially water extractions improved the resistance. The ethyl acetate extract was submitted to a bioguided fractionation, and fractions were tested against one wood-destroying fungal strain (Pycnoporus sanguineus) and two human pathogenic fungal strains (Candida glabrata (yeast) and Trichophyton rubrum (filamentous dermatophyte)). Fraction F7, which exhibited the strongest antifungal activity, was subsequently fractionated by high performance liquid chromatography (HPLC). Six previously described compounds were isolated. Although the two moracins, 6-O-methyl-moracin N (3) and moracin N (4) were the most active against fungal strains with MIC values between 4 and 16 μg ml−1, the isolated compounds showed less or equivalent antifungal activity than the initial fraction. Possible synergism between compounds 3 and 4 and other secondary metabolites have been hypothesized. Our study demonstrated that this extract as a whole might be used as a wood preservation or antimycotic product.
International Biodeterioration and Biodegradation

hal-00694532
https://hal.archives-ouvertes.fr/hal-00694532
DOI : 10.1016/j.ibiod.2011.10.016

Éditeur(s) : HAL CCSD Wiley
Résumé : Wood specific gravity (WSG) is a strong predictor of tree performance across environmental gradients. Yet it remains unclear how anatomical elements linked to different wood functions contribute to variation in WSG in branches and roots across tropical forests. [br/][br/]We examined WSG and wood anatomy in white sand, clay terra firme and seasonally flooded forests in French Guiana, spanning broad environmental gradients found throughout Amazonia. We measured 15 traits relating to branches and small woody roots in 113 species representing the 15 most abundant species in each habitat and representative species from seven monophyletic lineages occurring in all habitats. [br/][br/]Fiber traits appear to be major determinants of WSG, independent of vessel traits, in branches and roots. Fiber traits and branch and root WSG increased from seasonally flooded species to clay terra firme species and lastly to white sand species. Branch and root wood traits were strongly phylogenetically constrained. Lineages differed in wood design, but exhibited similar variation in wood structure across habitats. [br/][br/]We conclude that tropical trees can invest differently in support and transport to respond to environmental conditions. Wind disturbance and drought stress represent significant filters driving tree distribution of Amazonian forests; hence we suggest that biophysical explanations should receive more attention.
ISSN: 0028-646X

hal-01195075
https://hal.archives-ouvertes.fr/hal-01195075
PRODINRA : 269680
PUBMED : 24329812

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context and aim : This study aimed to examine the effect of the tension wood G‐layer on the viscoelastic properties of wood. Methods : Tension wood and opposite wood samples were obtained from six French Guianese tropical rainforest species (Sextonia rubra, Ocotea guyanensis, Inga alba, Tachigali melinoni, Iyranthera sagotiana and Virola michelii); the tension wood of the former three of these species had a Glayer, whilst the tension wood from the latter three had no Glayer. Tensile dynamic mechanical analysis (DMA) was performed on green never dried wood samples in the longitudinal direction with samples submerged in a water bath at a temperature (30°C) and frequency (1 Hz) representative of the conditions experienced by wood within a living tree. Then, DMA was repeated with samples conditioned to an air-dried state. Finally, samples were oven-dried to measure longitudinal shrinkage. Results : Tension wood did not always have a higher longitudinal storage (elastic) modulus than opposite wood from the same tree regardless of the presence or absence of a G‐layer. For the species containing a G‐layer, tension wood had a higher damping coefficient and experienced a greater longitudinal shrinkage upon drying than opposite wood from the same species. No difference was found in damping coefficients between tension wood and opposite wood for the species that had no G‐layer. Conclusion : It is proposed that the different molecular composition of the G-layer matrix has an influence on the viscoelasticity of wood, even if a biomechanical gain is not yet clear. This study shows that rheological properties and longitudinal shrinkage can be used to detect the presence of a G‐layer in tension wood.
ISSN: 1286-4560

hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460/document
https://hal.archives-ouvertes.fr/hal-00677460/file/Clair2.pdf
DOI : 10.1007/s13595-011-0164-1

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
In order to explain the durability of the Moraceae plant family, phytochemistry of Bagassa guianensis was performed. Ethyl acetate extract was obtained from the heartwood and 18 secondary metabolites were isolated, including 6 moracins [6-O-methyl-moracin M, 6-O-methyl-moracin N and moracin Z; previously identified: moracin M, moracin N and moracin P], 8 stilbenoids [presently identified: ( )-epialboctalol and arachidin 4; previously identified: alboctalol, trans-resveratrol, arachidin 2, trans-oxyresveratrol and artogomezianol], 3 previously identified flavonoids, steppogenin, katuranin and dihydromorin, bsitosterol and resorcinol. Previous studies suggest that stilbenoids are responsible for the natural durability of wood. Our study has determined that B. guianensis is closely related to Morus sp. in phylogeny and should be included in the Moreae sensu stricto tribe of the Moraceae family.
ISSN: 0031-9422

hal-00857200
https://hal.archives-ouvertes.fr/hal-00857200
https://hal.archives-ouvertes.fr/hal-00857200/document
https://hal.archives-ouvertes.fr/hal-00857200/file/Secondary_metabolites_Thibaut_al.pdf
DOI : 10.1016/j.phytochem.2010.06.020

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
Wallaba (Eperua falcata) is a tropical wood which is known to have naturally low swelling characteristics. Samples of wallaba heartwood were subjected to differential solvent extraction. Wood pieces that were extracted with methanol experienced significantly higher swelling after rehydration from oven dry to 96% relative humidity in comparison to non-extracted samples and samples extracted with other solvents. Methanol soluble wallaba heartwood extract was purified by high pressure liquid chromatography and the compounds present were characterised by nuclear magnetic resonance spectroscopy. Methanol extract was found to contain a very high relative proportion of polar compounds which are proposed to bind to the polymeric cell wall by multiple hydrogen bonds restricting the association of water and therefore acting as natural anti-swelling agents.
ISSN: 0018-3830

hal-00856942
https://hal.archives-ouvertes.fr/hal-00856942
https://hal.archives-ouvertes.fr/hal-00856942/document
https://hal.archives-ouvertes.fr/hal-00856942/file/Chemical_extractives_tropical_wood_Royer_al.pdf

Éditeur(s) : HAL CCSD Botanical Society of America
Résumé : Premise of the study : Wood density correlates with mechanical and physiological strategies of trees and is important for estimating global carbon stocks. Nonetheless, the relationship between branch and trunk xylem density has been poorly explored in neotropical trees. Here, we examine this relationship in trees from French Guiana and its variation among different families and sites, to improve the understanding of wood density in neotropical forests. Methods : Trunk and branch xylem densities were measured for 1909 trees in seven sites across French Guiana. A major-axis fit was performed to explore their general allometric relationship and its variation among different families and sites. Key results : Trunk xylem and branch xylem densities were significantly positively correlated, and their relationship explained 47% of the total variance. Trunk xylem was on average 9% denser than branch xylem. Family-level differences and interactions between family and site accounted for more than 40% of the total variance, whereas differences among sites explained little variation. Conclusions : Variation in xylem density within individual trees can be substantial, and the relationship between branch xylem and trunk xylem densities varies considerably among families and sites. As such, whole-tree biomass estimates based on non-destructive branch sampling should correct for both taxonomic and environmental factors. Furthermore, detailed estimates of the vertical distribution of wood density within individual trees are needed to determine the extent to which relying solely upon measures of trunk wood density may cause carbon stocks in tropical forests to be overestimated.
ISSN: 0002-9122

hal-01032401
https://hal.archives-ouvertes.fr/hal-01032401
DOI : 10.3732/ajb.1000034