Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Predicting the impact of underground engineering on the environment requires the knowledge of natural media at different scales. In particular, understanding basic phenomena controlling the properties of rocks in the presence of complex fluids necessitates a detailed atomic description of the solid/fluid/solid contacts, the subject of Part I of the present study. First, building the solid interspace between two different crystals in a non-periodic situation is achieved using the ab initio and molecular mechanics code GenMol (TM). A description of the fluid confined within the interspace is then derived from the original genetic iterative multi-species (GIMS) algorithm implemented in the same code. This approach consists of equilibrating chemical potentials, cycle after cycle and species after species, between the confined fluid and the free natural fluid. An elementary iteration for a species k consists of different steps incrementing the number N-k of particles k, with other numbers N-k remaining constant. At each step, an optimum fluid composition is obtained by a genetic process distributing the fluid particles on a grid by stochastic shots, followed in fine by a refining process. The effectiveness of the GIMS approach is demonstrated in the case study of a fluid confined between two (0 0 1) kaolinite faces, with apertures h varying between 4 and 10 A. connected to a 9-species external solution [H2O, Cl-, Na+ CO2(aq), NaCl(aq), Ca2+, Mg2+, HCO3-, H3O+] where concentrations are ranging from 55 to 10(-4) mol/L. The results show a drastic variation in the solute/solvent and cations/ions ratios in the confined fluid when aperture h is lowered to less than 1 nm. These results obtained with a very rapid convergence of the iterative algorithm combined with a very competitive genetic optimizer are validated with high precision on a free solution. This description of contacts between crystals is original and unattainable by standard crystal interface approaches. It opens the way to understanding and/or predicting phenomena between crystals in a complex natural environment, such as adhesion or repulsion investigated in the Part II of this study.
ISSN: 0022-0248

hal-00544569
https://hal.archives-ouvertes.fr/hal-00544569
DOI : 10.1016/j.jcrysgro.2010.08.009

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Although TRAIL (tumor necrosis factor (TNF)-related apoptosis inducing ligand) is a well-known apoptosis inducer, we have previously demonstrated that acidic extracellular pH (pHe) switches TRAIL-induced apoptosis to regulated necrosis (or necroptosis) in human HT29 colon and HepG2 liver cancer cells. Here, we investigated the role of RIPK1 (receptor interacting protein kinase 1), RIPK3 and PARP-1 (poly (ADP-ribose) polymerase-1) in TRAIL-induced necroptosis in vitro and in concanavalin A (Con A)-induced murine hepatitis. Pretreatment of HT29 or HepG2 with pharmacological inhibitors of RIPK1 or PARP-1 (Nec-1 or PJ-34, respectively), or transient transfection with siRNAs against RIPK1 or RIPK3, inhibited both TRAIL-induced necroptosis and PARP-1-dependent intracellular ATP depletion demonstrating that RIPK1 and RIPK3 were involved upstream of PARP-1 activation and ATP depletion. In the mouse model of Con A-induced hepatitis, where death of mouse hepatocytes is dependent on TRAIL and NKT (Natural Killer T) cells, PARP-1 activity was positively correlated with liver injury and hepatitis was prevented both by Nec-1 or PJ-34. These data provide new insights into TRAIL-induced necroptosis with PARP-1 being active effector downstream of RIPK1/RIPK3 initiators and suggest that pharmacological inhibitors of RIPKs and PARP-1 could be new treatment options for immune-mediated hepatitis.
ISSN: 1350-9047

inserm-00871432
http://www.hal.inserm.fr/inserm-00871432
DOI : 10.1038/cdd.2012.90
PUBMED : 22814620

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Collisional mountain belts grow as a consequence of continental plate convergence and eventuallydisappear under the combined effects of gravitational collapse and erosion. Using a decade ofGPS data, we show that the western Alps are currently characterized by zero horizontal velocityboundary conditions, offering the opportunity to investigate orogen evolution at the time ofcessation of plate convergence. We find no significant horizontal motion within the belt, but GPS andlevelling measurements independently show a regional pattern of uplift reaching ~2.5 mm/yr in thenorthwestern Alps. Unless a low viscosity crustal root under the northwestern Alps locally enhancesthe vertical response to surface unloading, the summed effects of isostatic responses to erosion andglaciation explain at most 60% of the observed uplift rates. Rock-uplift rates corrected from transientglacial isostatic adjustment contributions likely exceed erosion rates in the northwestern Alps. In theabsence of active convergence, the observed surface uplift must result from deep-seated processes.
ISSN: 2045-2322

hal-01357450
https://hal.archives-ouvertes.fr/hal-01357450
https://hal.archives-ouvertes.fr/hal-01357450/document
https://hal.archives-ouvertes.fr/hal-01357450/file/noquet2016.pdf
DOI : 10.1038/srep28404

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Talc is a hydrous magnesium rich layered silicate that is widely disseminated in the Earth from the seafloor to over 100 km depth, in ultra-high pressure metamorphism of oceanic crust. In this paper we determine the single crystal elastic constants at pressures from 0 to 12 GPa of talc triclinic (C 1¯) and monoclinic (C2/c) polytypes using ab initio methods. We find that talc has an extraordinarily high elastic anisotropy at zero pressure that reduces with increasing pressure. The exceptional anisotropy is complemented by a negative Poisson's ratio for many directions in crystal space. Calculations show that talc is not only one of very few common minerals to exhibit auxetic behaviour, but the magnitude of this effect may be the largest reported so far for a mineral. The compression (Vp) and shear (Vs) wave velocity anisotropy is 80% and 85% for the triclinic polytype. At pressures where talc is known be stable in the Earth (up to 5 GPa) the Vp and Vs anisotropy is reduced to about 40% for both velocities, which is still a very high value. Vp is slow parallel to the c-axis and fast perpendicular to it. This remains unchanged with increasing pressure and is observed in both polytypes. The shear wave splitting (difference between fast and slow S-wave velocities) at low pressure has high values in the plane normal to the c-axis, with a maximum near the alow asterisk-axis in the triclinic and the b-axis in the monoclinic polytype. The c-axis is the direction of minimum splitting. The pattern of shear wave splitting does not change significantly with pressure. The volume fraction of talc varies between 11 and 41% for hydrated mantle rocks, but the lack of data on the crystallographic preferred orientation (CPO) precludes a detailed analysis of the impact of talc on seismic anisotropy in subduction zones. However, it is highly likely that CPO can easily develop in zones of deformation due to the platy habit of talc crystals. For random aggregates of talc, the isotropic Vp, Vs and Vp/Vs ratio have significantly lower values than those of antigorite and may explain low-velocity regions in the mantle wedge. Vp/Vs ratios are more complex in anisotropic media because there are fast and slow S-waves, resulting in Vp/Vs1 and Vp/Vs2 ratios for every propagation direction, making interpretation difficult in deformed polycrystalline talc with a CPO. Talc on the subduction plate boundary can strongly influence guided wave velocity as CPO would develop in this region of intense shearing. The very low coefficient of friction (< 0.1) of talc above 100 °C could also explain silent earthquakes at shallow depths (ca 30 km) along the subduction plate boundaries, frequently responsible for tsunami.
ISSN: 0012-821X

hal-00411481
https://hal.archives-ouvertes.fr/hal-00411481
DOI : 10.1016/j.epsl.2008.07.047

Éditeur(s) : HAL CCSD Elsevier
Résumé : The dense hydrous magnesium silicate called the D phase is the most likely candidate to recycle hydrogen into the lower mantle in subduction zones. As seismology represents the preferred method to detect this mineral in subduction zones, the single crystal elastic tensor has been calculated using first principle methods. A triple cell (View the MathML source) was used to account for an ordered ideal composition of the D phase to lower mantle pressures. The elastic tensor of the mineral at ambient conditions is predicted to be C11 = 387.7, C33 = 287.7, C44 = 100.4, C12 = 108.0, C13 = 51.1, C14 = − 14.6 in GPa with bulk modulus at zero pressure Ko = 163 GPa and a statistical error of about 4.0 GPa for all constants. The pressure derivatives of the elastic constants have been determined to pressure of 80 GPa. Our tensor correctly predicts the published experimental measurements of linear compressibility along the a- and c-axes, the logarithmic pressure derivative of the c/a axial ratio and bulk modulus at zero pressure. It contradicts the experimentally measured elastic tensor reported by (Liu, L.-G., Okamoto, K., Yang, Y.-J., Chen, C.-C., Lin, C.-C., 2004. Elasticity of single-crystal phase D (a dense hydrous magnesium silicate) by Brillouin spectroscopy. Solid State Commun. 132, 517–520), which fails to reproduce the experimental compressibility data. Using the elastic constants and density predicted to 85 GPa, the seismic anisotropy of P- and S-waves has been calculated as a function of pressure. The single crystal has high P-wave velocities and shear wave splitting in the basal plane below 20 GPa. At high pressures, the maximum P-wave velocities have threefold symmetry normal to a-axes in the basal plane, whereas the maximum shear wave splitting is parallel to a-axes with twofold symmetry. The D phase has high Vp and Vs anisotropy at ambient pressure, 17.6% for Vp and 19.9% for Vs. The Vp anisotropy decreases with increasing pressure to about 30 GPa, while it remains constant at 8% from 30 to 85 GPa. The Vs anisotropy decreases to 17% at 20 GPa and then increases to 22% at 85 GPa. The isotropic velocity ratios of S to P (Rs/p), bulk sound to S (Rphi/s) and density to S (Rρ/s) are calculated as a function of pressure. The Rs/p shows very little variation with pressure with low value of 0.6, whereas both Rphi/s and Rρ/s increase with pressure to peak values of 2.8 and 2.0 respectively at about 60 GPa. The presence of the D phase in subducted horizontal ‘stagnant' plates in the circum Pacific could contribute to a number of seismic observations, such as the observed velocity heterogeneity at depths between 500 and 1000 km and the fast S-waves travelling horizontally with horizontal polarization in this depth range. Further the lower density of the D phase compared with anhydrous minerals could influence buoyancy of the hydrated ‘stagnant' slabs. The transformation of the D phase to perovskite plus ferripericlase during thermal annealing may be responsible for horizontal slab seismogenesis.
ISSN: 0012-821X

hal-00406379
https://hal.archives-ouvertes.fr/hal-00406379
DOI : 10.1016/j.epsl.2007.04.053

Éditeur(s) : HAL CCSD CRC Press Taylor & Francis Group
Résumé : In the chapter : Role of water-rock-gas interaction in sequestration of CO2
Water-Rock Interaction XIII

ISBN : 978-0415604260
hal-00855782
https://hal.archives-ouvertes.fr/hal-00855782

Éditeur(s) : HAL CCSD American Chemical Society
Résumé : The distribution of water and ions in nanoporous membranes, in particular close to their surfaces with external reservoirs, is investigated by means of molecular dynamics (MD) simulations using classical polarizable force fields. A sodium iodide (NaI) aqueous solution is considered in uncharged weakly hydrophilic (WH) and highly hydrophilic (HH) nanoporous materials modeled by a single truncated nanopore in contact with two reservoirs. In the inner part of the nanopore, the spatial distribution of water and ions is obtained by coupling semi-infinitesimal longitudinal and semi-infinitesimal radial descriptions. In the HH material, in contrast with the WH material, species are no longer uniformly distributed in the inner nanopore and water molecules are distributed in a nearly frozen axially periodic corona-like structure which leads to the formation of ionic tunnels. In the reservoirs, water molecules and ions attracted by the membrane surface create a necking of the confined solution which acts as a barrier at the entrance of the nanopore. In the WH nanopore subsurface, close to the surface of the membrane, the species distribution is analogous to the interface distribution between an aqueous electrolyte solution and air. In the HH nanopore subsurface, this distribution is modulated by the water corona-like structure. These results provide useful information for predicting properties of nanoporous membranes, in particular the drastic reduction of diffusion coefficients in HH materials, and give a guide to designing synthetic membranes for applications in nanofiltration, etc.
ISSN: 1932-7447

hal-00682155
https://hal.archives-ouvertes.fr/hal-00682155
DOI : 10.1021/jp2078924

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Claystone caprocks are often the ultimate seal for CO2 underground storage when residual CO2 gas reaches the reservoir top due to buoyancy. Permeability changes of a fractured claystone due to seepage of CO2-enriched brine and water vapor-saturated CO2 gas are investigated. Results show that brine flow induces a large porosity increase (up to 50%) in the vicinity of the fracture due to dissolution of calcite and quartz, while permeability remains unchanged. Conversely, cyclic flows of CO2-brine and CO2-gas increase the fracture aperture abruptly after each gas flow period, producing a progressive decrease of the caprock seal capacity. Aperture increase is controlled by decohesion of the clay framework within a micrometer-scale-thick layer induced by CO2-gas acidification. Results show that hydraulic aperture increases linearly with duration of the preceding CO2-brine flow period, emphasizing the kinetic control of the quartz grains dissolution during the brine flow periods.
ISSN: 0094-8276

hal-00412332
https://hal.archives-ouvertes.fr/hal-00412332
DOI : 10.1029/2008GL034467

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Properties of composite materials depend on interatomic phenomena occurring between binder crystals. Experimental information of Atomic Force Microscopy (A.F.M.) is of prime importance; however understanding is helped by molecular modeling. As underlined in Section 1, the present study is able to simulate crystal interfaces in presence of a solution within apertures less than 1 Nanometer at a full atomic scale. Section 2 presents the case study of a gypsum solution between (120) gypsum faces, with related boundary conditions and atomic interactions. Section 3 deals with the mass equilibrium of the solution within interfaces <5 angstrom, using the original Semi Analytical Stochastic Perturbations (SASP) approach. This information becomes in Section 4 the key for explaining the peak of adhesion obtained in A.F.M. around an aperture of 3 A and gives enlightenments on gypsum cohesion. In conclusion, this illustration shows the potentialities of full atomic modeling which could not be attained by any numerical approach at a mesoscopic scale.
ISSN: 0008-8846

hal-00411868
https://hal.archives-ouvertes.fr/hal-00411868
DOI : 10.1016/j.cemconres.2007.09.022

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
We predict the IR-TO, IR-LO and Raman modes (wave numbers and intensities) of magnesite (MgCO3) up to 50 GPa, at T = 0 K, using the density-functional perturbation theory up to a third order perturbation, under the harmonic assumption. The predicted IR-TO and Raman mode wave numbers, the mode Grüneisen parameters and the Davydov splittings are systematically compared with experimental data for all modes up to the pressures of 10-30 GPa and for some modes up to 50 GPa. Existing experiments allow extending this comparison only to IR-LO wave numbers of the E u (ν3) asymmetric-stretch mode, confirming the odd experimental behavior of this mode at very high pressures. Predicted IR-TO, IR-LO and Raman intensities up to 50 GPa are just tabulated, but data are missing for their comparison with precise experiments. However, the generally good agreement observed between numerical results and experimental data, when their comparison is possible, suggests that first-principles methods are a major help to predict the entire spectrum up to very high pressures.
ISSN: 0342-1791

hal-00527834
https://hal.archives-ouvertes.fr/hal-00527834
DOI : 10.1007/s00269-010-0395-y

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
GenMol (TM) code is used to simulate Atomic Force Microscopy (AFM) tests at a kaolinite/brine/kaolinite contact, the confined fluid in sub-nanometre interspaces being in equilibrium with an external multi-species solution. The attraction/repulsion effort, i.e. the derivative versus the interspace aperture h of the interaction energy between both kaolinite faces, is computed versus the variable composition of the confined fluid (see for the method Part I of this work). Two external solutions are tested. Solution Si is a neutral brine (pH=7.5) leading to a possible attraction for apertures lower than 7 angstrom. Solution S2 is an acidified brine (pH=3.2) leading to repulsion whatever may be the aperture h. These two AFM simulations prove the existence of a critical pH value (3.2 < pH(crit) < 7.5) of the external solution, below which the acidification of a natural brine in a CO2 confinement inhibits adhesion between kaolinite aggregates.
ISSN: 0022-0248

hal-00544678
https://hal.archives-ouvertes.fr/hal-00544678
DOI : 10.1016/j.jcrysgro.2010.08.012