Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
Large-scale conical and saucer-shaped sand injectites have been identified in the Upper Miocene sediments of the Lower Congo Basin. These structures are evidenced on the 3D high-resolution seismic data at about 600 ms TWT (two-way traveltime) beneath the seabed. The conical and saucer-shaped anomalies range from 20 to 80 m in height, 50 to 300 m in diameter, and 10 to 20 ms TWT in thickness. They are located within a sedimentary interval of about 100 m in thickness and are aligned over 20 km in dip direction (NE-SW), above the NW margin of an underlying Upper Miocene submarine fan. We have interpreted the conical and saucer-shaped anomalies as upward-emplaced sand injectites sourced from the Upper Miocene fan because of their discordant character, the postsedimentary uplifting of the sediments overlying the cones and saucer-shaped bodies, the alignment with the lateral fringe of the Upper Miocene submarine fan, and the geological context. Sand injection dates from the Miocene-Pliocene transition (approximately 5.3 Ma). The prerequisite overpressure to the sand injection process may be due to the buoyancy effect of hydrocarbons accumulated in the margins of the fan. Additionally, overpressure could have been enhanced by the lateral transfer of fluids operating in the inclined margins of the lobe. The short duration of sand injection and the presence of many sandstone intrusions suggested that the process of injection was triggered by an event, likely due to a nearby fault displacement related to diapiric movements. This is the first time that sand injectites of seismic scale have been described from the Lower Congo Basin. The localized nature of these injectites has led to a change in the migration path of fluids through the sedimentary cover. Consequently, the sand intrusions are both evidence and vectors of fluid migration within the basin fill.
ISSN: 1468-8115

hal-00963594
https://hal.archives-ouvertes.fr/hal-00963594
DOI : 10.1111/gfl.12057

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Large sand intrusions often exhibit conical morphologies analogous to magmatic intrusions such as saucer-shaped or cup-shaped sills. Whereas some physical processes may be similar, we show with scaled experiments that the formation of conical sand intrusions may be favoured by the pore-pressure gradients prevailing in the host rock before sand injection. Our experiments involve injecting air into a permeable and cohesive analogue material to produce hydraulic fractures while controlling the pore pressure field. We control the state of overpressure in the overburden by applying homogeneous basal pore pressure, and then adding a second local pore pressure field by injecting air via a central injector to initiate hydraulic fractures near the injection point. In experiments involving small vertical effective stresses (small overburden, or high pore fluid overpressure), the fracturing pressure (lambda(fract)) is supralithostatic and two dipping fractures are initiated at the injection point forming a conical structure. From theoretical considerations, we predict that high values of lambda(fract), are due to strong cohesion or high pore fluid overpressure distributed in the overburden. Such conditions are favoured by the pore pressure/stress coupling induced by both pore pressure fields. The dips of cones can be accounted for elastic-stress rotation occurring around the source. Contrary to magmatic chamber models, the aqueous fluid overpressure developed in a parent sandbody (and prevailing before the formation of injectites) may diffuse into the surrounding overburden, thus favouring stress rotation and the formation of inclined sheets far from the parent source. For experiments involving higher vertical effective stresses (thick overburden or low pore fluid overpressure), the fracturing pressure is lower than the lithostatic stress, and a single fracture is opened in mode I which then grows vertically. At a critical depth, the fracture separates into two dilatant branches forming a flat cone. We make use of a P.I.V. (Particle Imaging Velocimetiy) technique to analyse plastic deformation, showing that these inclined fractures are opened in mixed modes. Close to the surface, they change into steep shear bands where fluids can infiltrate. The final morphology of the fracture network is very similar to the common tripartite architecture of various injection complexes, indicating that different mechanisms may be involved in the formation of dykes. Feeder dykes under the sill zones may open as tensile fractures, while overlying dykes may be guided by the deformation induced by the growth of sills. These deformation conditions may also favour the formation of fluid escape structures and pockmarks. (C) 2011 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00745640
https://hal.archives-ouvertes.fr/hal-00745640
DOI : 10.1016/j.epsl.2011.10.029

Éditeur(s) : HAL CCSD
Résumé : Sand intrusions (or injectites) are most often the product of post-depositional remobilization of sand leading to its injection into the surrounding rocks. While injectites were recognized for the first time nearly 200 years ago, their emplacement process has been studied for a couple of decades only, since the concepts of deep sea depositional environments have allowed us to better understand their emplacement processes. However, these processes are still relatively poorly understood. Our approach is based on the study of injectites in the Lower Congo Basin from seismic and well data, which we compare to a fossil system in the SE France basin. We have shown that: (1) In buried turbidite channel systems draping deposits on the channel flanks and terraces of channels have the same geophysical signature as 'wing-like' injectites. Finally, the only criterion for identifying seismic injectites is the presence of bedding-discordant seismic reflections, and in the best case the associated uplift of the overlying seismic reflectors. (2) Seismic-scale conical and saucer-shaped sand injectites have been identified in the Lower Congo Basin. The remobilization is likely due to overpressuring induced by the buoyancy effect of hydrocarbons trapped in the margins of a lobe buried underneath 160 m of sediment, followed by the sudden injection of fluidized sand associated with fault reactivation of faults (with a possible role of nearby salt diapirs). (3) A network of injectites (dykes, sills/wings and laccoliths) was formed in the Vocontian basin during the late Albian and/or early Cenomanian, from a lower-middle Albian turbidite channel. The emplacement is probably due to the early compartmentalization of the channel during its burial and the increase of the sedimentation rate generating overpressure; and the subsequent large influx of deep fluids triggering injection. The injection of sand was polyphased: a first episode formed the sills and another emplaced the dykes. Sills/wings and dykes propagated about 2 km laterally away from the parent sand body and about 200 m up to the surface, revealing a much more extended lateral than vertical reach, contrary to the classically accepted idea from the interpretation of seismic data. (4) The emplacement of this large network of injectites was governed by hydrofracturing. Therefore, its morphology is dependent on the host rock heterogeneity (isotropy, fractures), the paleo-stress orientation (ó3 = NW-SE) and the burial depth of the source (300-600 m) at the time of injection. The study of this fossil network allows us to define the relationship between morphology of the injected network and stress state at the time of injection. This relationship can be extrapolated to constrain the morphology of subsurface networks beyond seismicvisibility. (5) Sands injected into low permeability lithologies bear evidence to a major event of fluid escape in the studied basin, but also channeled fluids long after their formation. In this way, injectites both attest to specific episodes of fluid migration in sedimentary basins and contribute to long-lived re-routing of migrating fluids once emplaced. The injection of sand is associated with the sudden escape of fluids, probably resulting from a significant tectonic and/or sedimentary event; in addition, the architecture of injectite networks is governed by the local paleo-stress and heterogeneity in the host rock. Consequently, characterizing injectite networks is an important step in understanding the plumbing systems of continental margins, i.e. the post-depositional evolution of sedimentary basins.
Les intrusions sableuses (ou injectites) sont le plus souvent le produit de la remobilisation post-dépositionnelle des sédiments et de l'injection du sable dans les roches environnantes. Bien que reconnues pour la première fois il y a près de 200 ans, elles ne sont réellement étudiées que depuis quelques dizaines d'années, depuis que les concepts sur les environnements de dépôt dans les domaines marins profonds nous permettent de mieux comprendre les processus de mise en place. Cependant, ces processus restent encore aujourd'hui relativement mal compris. Notre approche repose sur l'étude d'injectites dans le bassin du Bas-Congo a partir de données de sismique et de puits que nous comparerons a un système fossile dans le bassin du SE de la France. Nous avons montre que : (1) Dans des systèmes de chenaux turbiditiques enfouis, les dépôts de drapage sur les marges et terrasses de chenaux présentent la même signature géophysique que les injectites de type "wing". Finalement, le seul critère sismique d'identification des injectites est la présence de réflexions sismiques sécantes vis-a-vis de la stratigraphie associée dans le meilleur des cas au soulèvement des réflecteurs sismiques sus-jacents. (2) Des injectites d'échelle sismique en forme de cône et d'assiette ont été identifiées dans le bassin du Bas-Congo. La remobilisation résulte probablement des pressions anormales induites par l'effet de flottabilité des hydrocarbures piégés dans les marges d'un lobe enfoui sous 160 m de sédiment, puis de l'injection soudaine du sable fluidise associée a la réactivation de failles (possible rôle des diapirs de sel a proximité). (3) Un réseau d'injectites (dykes, sills/wings et laccolites) s'est formé dans le bassin Vocontien entre la fin de l'Albien supérieur et/ou le début du Cénomanien, depuis un chenal turbiditique de l'Albien inférieur-moyen. La mise en place résulte probablement de la compartimentalisation précoce du chenal au cours de son enfouissement et de l'augmentation du taux de sédimentation générant la surpression et de l'apport ulterieur d'importante quantité de fluides profonds déclenchant l'injection. L'injection du sable a été polyphasée : une première injection a formé des sills et une suivante des dykes. Les sills/wings et les dykes se sont propagés latéralement au chenal source sur environ 2 km et vers la surface sur environ 200 m, mettant en évidence une forte remobilisation latérale plutôt que verticale, contrairement a l'idée classiquement admise a partir de l'interprétation des données sismiques. (4) La formation de ce large réseau d'injectites a été gouvernée par des mécanismes d'hydrofracturation. Par conséquent, sa morphologie a été dépendante des hétérogenéités de la roche hôte (milieu isotrope, fracture), des directions de paléo-contraintes (ƒÐ3 = NWSE) et de la profondeur d'enfouissement de la source (300-600 m) au moment de l'injection. L'étude de ce réseau fossile permet de définir les relations entre morphologie du réseau injecté et état de contraintes au moment de l'injection. Cette relation peut être extrapolée de façon à contraindre la morphologie des réseaux de subsurface au-delà de la visibilité sismique. (5) Les sables injectés dans des lithologies de faible perméabilité témoignent d'un épisode d'échappement de fluide important dans les bassins étudiés mais ont aussi guide les fluides longtemps après leur formation. Les injectites contribuent ainsi a l'initiation épisodique et la pérennisation de migrations de fluides dans les bassins sedimentaires. Le processus d'injection est associé a l'échappement brutal de fluides, résultant vraisemblablement d'un évènement tectonique et/ou sédimentaire important, et l'architecture des réseaux d'injectites est gouverné par les paléo-contraintes locales et les hétérogénéités de la roche hôte. Par conséquent, la caractérisation des réseaux d'injectites est une étape importante dans la compréhension de la plomberie des marges, c'est-a-dire l'évolution post-dépôt des bassins sédimentaires.
https://tel.archives-ouvertes.fr/tel-01011486

tel-01011486
https://tel.archives-ouvertes.fr/tel-01011486
https://tel.archives-ouvertes.fr/tel-01011486/document
https://tel.archives-ouvertes.fr/tel-01011486/file/These_Monnier_2013_banalisee.pdf