Éditeur(s) : HAL CCSD American Physical Society
Résumé : International audience
This is the second of two papers investigating the mechanical response of cemented granular materials by means of contact dynamics simulations. In this paper, a two-dimensional polydisperse sample with high void ratio is sheared in a load-controlled simple shear numerical device until the stress state of the sample reaches the yield stress. We first study the stress transmission properties of the granular material in terms of the fabric of different subsets of contacts characterized by the magnitude of their normal forces. This analysis highlights the existence of a peculiar force carrying structure in the cemented material, which is reminiscent of the bimodal stress transmission reported for cohesionless granular media. Then, the evolution of contact forces and torques is investigated trying to identify the micromechanical conditions that trigger macroscopic yielding. It is shown that global failure can be associated to the apparition of a group of particles whose contacts fulfill at least one of the local rupture conditions. In particular, these particles form a large region that percolates through the sample at the moment of failure, evidencing the relationship between macroscopic yielding and the emergence of large-scale correlations in the system.
ISSN: 1539-3755

hal-00523451
https://hal.archives-ouvertes.fr/hal-00523451
DOI : 10.1103/PhysRevE.82.011304

Éditeur(s) : HAL CCSD De Gruyter
Résumé : COST Action E35 : Fracture mechanics and micromechanics of wood and wood composites with regard to wood machining
The data available in the literature concerning wood cutting forces permits to build models or to simulate the main wood machining processes ( milling, sawing, peeling, etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimise cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: ( 1) providing data to optimise the settings for a given operation ( batch approach), and ( 2) building predictive models that could be the basis of an online control system for the machining processes ( interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With a focus on potential industrial applications, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Although not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technological knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-01032121
https://hal.archives-ouvertes.fr/hal-01032121
DOI : 10.1515/HF.2009.014

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wood has a hierarchical structure involving several levels of organisation. The stiffness of wood relies on its capacity to transfer mechanical stress to its stiffest element at the lowest scale, namely crystalline cellulose. This study aims at quantifying to what extend crystalline cellulose contributes to wood stiffness depending on its moisture content. The crystal strains of cellulose were measured using X-ray diffraction on wet and dry specimens of spruce, based on a previously published methodology. The comparison between crystal strain and macroscopic strain shows that, during elastic loading, cellulose strain is lower than macroscopic strain. The means ratio of crystal/macroscopic strain amounts 0.85 for dry specimens and 0.64 for wet specimens. This strain ratio cannot be explained just by the projection effect due to the difference in orientation between cellulose microfibrils and cell wall, but results from deformation mechanisms in series with cellulose. Analysis shows that this series contribution represents a non-negligible contribution to wood compliance and is strongly moisture-dependent. This contribution amounts 9% for dry specimens and 33% for wet specimens, corresponding to a 4-fold increase in compliance for the series contribution. The origin of these strains is ascribed to mechanisms involving bending or shear strain at different scales, due to the fact that reinforcing element are neither perfectly straight nor infinitely long.
ISSN: 0266-3538

hal-01425031
https://hal.archives-ouvertes.fr/hal-01425031
https://hal.archives-ouvertes.fr/hal-01425031/document
https://hal.archives-ouvertes.fr/hal-01425031/file/Art_Almeras_al_Contribution_cellulose_moisture-dependent_elastic_behavior_2017.pdf
DOI : 10.1016/j.compscitech.2016.11.025

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Properties of composite materials depend on interatomic phenomena occurring between binder crystals. Experimental information of Atomic Force Microscopy (A.F.M.) is of prime importance; however understanding is helped by molecular modeling. As underlined in Section 1, the present study is able to simulate crystal interfaces in presence of a solution within apertures less than 1 Nanometer at a full atomic scale. Section 2 presents the case study of a gypsum solution between (120) gypsum faces, with related boundary conditions and atomic interactions. Section 3 deals with the mass equilibrium of the solution within interfaces <5 angstrom, using the original Semi Analytical Stochastic Perturbations (SASP) approach. This information becomes in Section 4 the key for explaining the peak of adhesion obtained in A.F.M. around an aperture of 3 A and gives enlightenments on gypsum cohesion. In conclusion, this illustration shows the potentialities of full atomic modeling which could not be attained by any numerical approach at a mesoscopic scale.
ISSN: 0008-8846

hal-00411868
https://hal.archives-ouvertes.fr/hal-00411868
DOI : 10.1016/j.cemconres.2007.09.022

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
The data available in the literature concerning wood cutting forces permit to build models or to simulate the main wood machining processes (milling, sawing, peeling etc.). This approach contributes to a better understanding of formation of wood surfaces and chips and the data may be helpful to optimize cutting geometry, reduce tool wear, improve tool material, and to size tool-machines. The models may also be useful for industrial application in two ways: (1) providing data to optimise the settings for a given operation (batch approach) and (2) building predictive models that could be the basis of an online control systems for the machining processes (interactive approach). A prerequisite for this is that numerous machining tests on different wood materials are performed based on experiences with different kind of tools and experimental devices. With potential industrial applications in focus, the emphasis of this review was on the wood peeling process, which is a very demanding special case of wood cutting. Though not so many industrial machines are equipped with expensive force sensors, there is a lot of high quality information available about cutting forces which may be useful to improve the scientific or technologic knowledge in wood machining. Alternative parameters, such as vibration or sound measurements, appear to be promising substitutes in the praxis, particularly to feed online control systems of any wood cutting process.
ISSN: 0018-3830

hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003
https://hal.archives-ouvertes.fr/hal-00876003/document
https://hal.archives-ouvertes.fr/hal-00876003/file/LABOMAP_Holzforschung_2009_denaud.pdf
ENSAM : http://hdl.handle.net/10985/7419

Éditeur(s) : HAL CCSD
Résumé : International audience
The hierarchical architecture of biopolymers induces remarkable behaviour. Wood mechanical properties mainly originate from the organization of wood tissue and interactions of cellwall components. The respective contribution on components inside those networks occurs at nanometric scale and still challenging to investigate in-situ. X-ray scattering techniques are now used as a routine technique to investigate internal organization of material components. For that purpose large-scale synchrotron facilities like ESRF offer leading X-ray sources capabilities (large energy range, high brilliance, high intensity, dedicated setups). ESRF's ID13 beamline serves high spacial resolution scanning setups to expertise in elastic scattering of monochromatic X-rays. Since analytical description of the scattering signal of cellulose have been well describe wood material benefit wide range of exposure conditions and sample environment. During this conference, we will present our achievements based on transverse sections of poplar specimens exposed to micrometric beam (1.2 μm side, 12.6 keV energy) to reveal crystalline cellulose distribution within wood tissue and to nanometric beam (100 nm side, 12 6 keV energy) to map the evolution of cellulose orientation within double cell wall over combined Wide-Angle (WAXS) and Small-Angle (SAXS) X-ray Scattering configuration. Within those setups hygrometric sample environment and stretching solicitations will be approached based on-going developments.
COST FP0802 Workshop 'Micro Characterisation of Wood Material'
Edimbourg, United Kingdom

hal-01113298
https://hal.archives-ouvertes.fr/hal-01113298