Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This work shows the preparation and separation performance assessment of carbon membranes derived from phenolic resin by a vacuum-assisted method and carbonisation in an inert atmosphere. The vacuum time played an important role in tailoring the structure of the membranes. For instance, pore volumes and surface areas increased from 0.81 and 834 to 2.2 cm3g−1and 1910 m2g−1, respectively, as the vacuum time exposure increased from 0 to 1200 s. The significant structural changes correlated very well with water permeation, as fluxes increased by 91% as the vacuum time increased from 0 to 1200 s reaching up to 169 L m−2h−1at 5 bar. Molecular weight cut-off tests showed no rejection for the smaller glucose and sucrose molecules, though this increased to ~ 80% and full rejection for 36 kDa and 400 kDa polyvinyl pyrrolidine. Interestingly, FTIR spectra showed that the peaks of C–H stretching vibration (2800–3200 cm−1) and C–O stretching (1030 cm−1) became more pronounced as a function of increasing vacuum time, strongly suggesting that the use of vacuum further assisted in the polycondensation of phenolic oligomers. Based on these outcomes, a cluster to cluster model is proposed, whereby vacuum application promoted crosslinking reactions of the phenolic resin, creating microporous regions within the clusters, and mesoporous regions between the clusters. © 2016 Elsevier B.V
ISSN: 0376-7388

hal-01683220
https://hal.univ-antilles.fr/hal-01683220
DOI : 10.1016/j.memsci.2016.11.002

Éditeur(s) : HAL CCSD MDPI
Résumé : International audience
This work investigates the structural formation and analyses of titania membranes (TM) prepared using different vacuum exposure times for molecular weight (MW) cut-off performance and oil/water separation. Titania membranes were synthesized via a sol-gel method and coated on macroporous alumina tubes followed by exposure to a vacuum between 30 and 1200 s and then calcined at 400 °C. X-ray diffraction and nitrogen adsorption analyses showed that the crystallite size and particle size of titania increased as a function of vacuum time. All the TM membranes were mesoporous with an average pore diameter of ~3.6 nm with an anatase crystal morphology. Water, glucose, sucrose, and polyvinylpyrrolidone with 40 and 360 kDa (PVP-40 kDa and PVP-360 kDa) were used as feed solutions for MW cut-off and hexadecane solution for oil filtration investigation. The TM membranes were not able to separate glucose and sucrose, thus indicating the membrane pore sizes are larger than the kinetic diameter of sucrose of 0.9 nm, irrespective of vacuum exposure time. They also showed only moderate rejection (20%) of the smaller PVP-40 kDa, however, all the membranes were able to obtain an excellent rejection of near 100% for the larger PVP-360 kDa molecule. Furthermore, the TM membranes were tested for the separation of oil emulsions with a high concentration of oil (3000 ppm), reaching high oil rejections of more than 90% of oil. In general, the water fluxes increased with the vacuum exposure time indicating a pore structural tailoring effect. It is therefore proposed that a mechanism of pore size tailoring was formed by an interconnected network of Ti-O-Ti nanoparticles with inter-particle voids, which increased as TiO2 nanoparticle size increased as a function of vacuum exposure time, and thus reduced the water transport resistance through the TM membranes. © 2016 by the authors.
ISSN: 1996-1944

hal-01683214
https://hal.univ-antilles.fr/hal-01683214
DOI : 10.3390/ma9110938