Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Extractives can affect vibrational properties tanδ (damping coefficient) and E'/ρ (specific Young's modulus) but this is highly dependent on species, compounds, and cellular locations. This paper investigates such effects for African Padauk (Pterocarpus soyauxii Taub.), a tropical hardwood with high extractives content and a preferred material for xylophones. 5 groups of 26 heartwood specimens with large, yet comparable, ranges in vibrational properties were extracted in different solvents. Changes in vibrational properties were set against yields of extracts and evaluation of their cellular location. Methanol (ME) reached most of compounds (13%), located about half in lumen and half in cell-wall. Water solubility was extremely low. tanδ and E'/ρ were very strongly related (R2≥0.93), but native wood had abnormally low values of tanδ, while extraction shifted this relation towards higher tanδ values. ME extracted heartwood became in agreement with the average of many species, and close to sapwood. Extractions increased tanδ as much as 60%, irrespective of minute moisture changes or of initial properties. Apparent E'/ρ was barely changed (+2% to -4%) but, after correcting the mass contribution of extracts, was in fact slightly reduced (down to -10% for high E'/ρ), and increasingly so for specimens with low initial values of E'/ρ.
ISSN: 0043-7719

hal-00804236
https://hal.archives-ouvertes.fr/hal-00804236
https://hal.archives-ouvertes.fr/hal-00804236/document
https://hal.archives-ouvertes.fr/hal-00804236/file/Effect_extractives_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0337-3

Résumé : Une étude de faisabilité de poutres en bois lamellé-collé a été menée en Guyane Française en utilisant les essences locales. Le but est de déterminer les paramètres de collage assurant la bonne résistance mécanique des assemblages par lamellation et par aboutage, nécessaires à la fabrication de poutres en bois lamellé-collé en climat tropical. Trois essences de bois abondantes de différentes densités ont été sélectionnées. Les adhésifs de types Mélamine-Urée-Formol et Résorcinol-Phénol-Formol ont été utilisées. Les paramètres de collage considérés sont : le grammage, le temps d’assemblage fermé et la pression.En utilisant les normes Européennes, plusieurs campagnes de tests ont été conduites sur des échantillons normalisés. Concernant le collage par lamellation, des tests élémentaires de délamination et de cisaillement des joints de colle ont été réalisés. Le test de délamination consiste en deux cycles d’immersion dans l’eau sous pression et de séchage, il induit de sévères variations d’humidité du bois susceptibles de créer des ouvertures des joints de colles. Le collage par aboutage est réalisé sur des poutres normalisées aboutées. Les entures sont obtenues grâce à un outillage standard communément utilisé pour les résineux. Les résultats ont mis en évidence l’influence des propriétés du bois et des paramètres de collage sur la résistance du joint et la résistance mécanique du produit. En effet, les paramètres du bois, tels que la densité, la rétractibilité et l’imprégnation, ont une forte influence sur le collage, en particulier sur la pression et le grammage nécessaires à la production d’un produit commercialisable. Il apparait qu’un bois de densité moyenne et poreux nécessite un grammage et une pression élevés comparé à un bois de densité élevée qui nécessite des valeurs moindres. Aussi, l’influence d’autres paramètres de fabrication, tels que le rabotage, l’encollage double face et simple face ainsi que l’épaisseur des lamelles, a été établie. Par contre il semblerait que le matériel communément utilisé pour l’aboutage des résineux n’est pas adapté aux feuillus tropicaux. En final, des paramètres de collage ont été validés pour la fabrication de lamellé-collé endémique en Guyane Française et une étude du coût de production d’une poutre lamellé-collé standard a identifié les conditions économiques d’une fabrication en Guyane Française.
A feasibility study of glued-laminated timber beams was carried out in French Guiana using local wood species. The aim of the study was to evaluate the gluing parameters that could ensure good mechanical properties for the manufactured glued-laminated beams in tropical climates. Three abundant wood species with different specific gravity were selected for the study. Melamine-Urea-Formaldehyde and Resorcinol-Phenol-Formaldehyde resins were used for gluing. The three gluing parameters considered are: adhesive spread rate, closing assembly time and gluing pressure.Using European standards, several laboratory tests were performed on normalized samples. The evaluation of a successful lamella’s gluing was done by using elementary tests of delamination and shearing. A delamination test consists of two cycles of water immersion at high pressure and drying which induces severe hygroscopic variation in wood thus causing joints opening. The finger-joints are made using a standard tool usually used for cutting softwoods. The performed tests revealed the influence of wood properties and the gluing parameters on the joint resistance and the mechanical properties of the product. Results show that wood properties such as specific gravity, shrinkage coefficient, and permeation, have a high degree of influence on the gluing step especially on the gluing pressure and on the adhesive spread rate needed to produce a commercial product. Furthermore, wood with medium specific gravity needs more adhesive and more pressure than the one with high specific gravity. Additionally, the effects of other manufacturing parameters, such as planning, double or simple side glue spreading and lamellae thicknesses, on the glue joint resistance were demonstrated. Finally, the common tools used for softwoods are not adapted to making the finger joints with tropical hardwoods.In conclusion, optimal gluing parameters for manufacturing glued-laminated timber beams in French Guiana were established and an economical study using standard glued-laminated timber beams revealed the economic conditions under which a successful manufacturing of these local beams can be implemented in French Guiana.

http://www.theses.fr/2011AGUY0484/document

Éditeur(s) : HAL CCSD
Résumé : International audience
A key element of the biomechanical design of trees is their ability to generate largemechanical stresses in wood at the stem periphery. This function is necessary for the tree tocontrol the orientation of its axes, and therefore to grow in height, maintain its branches at anoptimal angle or achieve adaptive reorientations (Fournier et al., 2013). This “maturationstress” appears in wood fibres during their cellular maturation when their secondary cell wallis thickening. In hardwoods, the stress asymmetry is generated by the formation of specificfibres with a very high tensile growth stress on the upper side of the inclined axis. Theresulting tension wood has microstructural features highly different from the normal wood.Tension wood in almost all temperate species has a specific gelatinous cell wall layer, calledG-layer, that is not lignified and highly mesoporous (Chang et al., 2015). It has been shownrecently, at the macroscopic scale, that cellulose tension appears during maturation and issynchronous with the development of this specific layer (Clair et al., 2011). Tropical species,like simarouba, are able to generate lignified tension wood fibres. The mechanisms of stressgeneration in tension wood fibres are not yet well known. The aim of our study is tounderstand these mechanisms and to know the spatial and temporal kinetics of the differentcell wall layers stiffening during maturation, in parallel with tensile stress generation.Contact-Resonance Atomic Force Microscopy, CR-AFM, was used here to address thisquestion on embedded samples (Arnould and Arinero, 2015) using dual resonance frequencytracking (DRFT, Rodriguez et al., 2007). Change in the contact modulus between, and within,each layer of the cell wall has been measured on several radial lines of developing fibres atdifferent steps. In order to understand the obtained results, and to estimate the sensitivity ofthe AFM indentation-like technique to the different cell wall components stiffness, an elasticanisotropic indentation model was used (Vlassak et al., 2003; Jäger et al., 2011). Finally,these mechanical measurements have been compared to topochemical data obtained on thesame fibres.
8th Plant Biomechanics International Conference
Nagoya, Japan

hal-01436113
https://hal.archives-ouvertes.fr/hal-01436113

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Radial trends of vibrational properties, including the specific dynamic modulus (E'/r) and damping coefficient (tand), were investigated for 3 tropical rainforest hardwood species, Simarouba amara, Carapa procera and Symphonia globulifera by free-free flexural vibration test. The microfibril angle (MFA) was estimated through X-Ray diffraction. Consistent patterns of radial variations were observed for all studied properties. E'/r was found to decrease from pith to bark, which is strongly related to the increasing pith-bark trend of MFA. The variation of tand along the radius can be partly explained by MFA, and partly by the gradient of extractives due to heartwood formation. The coupling effect of MFA and extractives could be separated through the analysis of log(tand) - log(E'/r) diagram. For the studied species, the extractive content putatively associated to heartwood formation generally tends to decrease the wood damping coefficient. However, this weakening effect of extractives was not observed for inner part of the heartwood, suggesting the mechanical action of extractives was reduced during their chemical ageing.
ISSN: 1435-0211

hal-00797055
https://hal.archives-ouvertes.fr/hal-00797055
https://hal.archives-ouvertes.fr/hal-00797055/document
https://hal.archives-ouvertes.fr/hal-00797055/file/Radial_variations_vibrational_Zhang_al.pdf

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
*Context Increased knowledge on diversity in wood properties would have implications both for fundamental research and for promoting a diversification of uses as material. *Aims The objective is to contribute to overcoming the critical lack of data on the diversity of wood dynamic mechanical/viscoelastic vibrational properties, by testing lesser-known species and categorizing sources of variability. *Methods Air-dry axial specific dynamic modulus of elasticity (E'/γ) and damping coefficient (tanδ) were measured on a wide sampling (1792 specimens) of 98 wood types from 79 species. An experimental device and protocol was designed for conducting systematic (i.e. rapid and reproducible) characterizations. *Results Diversity at the specimens' level corroborates the "standard" relationship between tanδ and E'/γ, which is discussed in terms of orientation of wood elements and of chemical composition. Diversity at the species level is expressed on the basis of results for normal heartwood, with specific gravity (γ) ranging from 0.2 to 1.3. Axial E'/γ ranges from 9 to 32 GPa and tanδ from 4×10-3 to 19×10-3. Properties distribution follows a continuum, but with group characteristics. The lowest values of tanδ are only found in certain tropical hardwoods. Results can also suggest alternative species for musical instruments making.
Annals of Forest Science

hal-00808242
https://hal.archives-ouvertes.fr/hal-00808242
https://hal.archives-ouvertes.fr/hal-00808242/document
DOI : 10.1007/s13595-011-0166-z

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Grain deviations and high extractives content are common features of many tropical woods. We aimed at clarifying their respective impact on vibrational properties, referring to African Padauk (Pterocarpus soyauxii Taub.), a species selected for its interlocked grain, high extractives content, and uses in xylophones. Specimens were cut parallel to the trunk axis (L), and local variations in grain angle (GA), microfibril angle (MFA), specific Young's modulus (E'L/ρ, where r stands for specific gravity) and damping coefficient (tanδL), were measured. GA dependence was analyzed by a mechanical model which allowed to identify the specific Young's modulus (E'3/ρ) and shear modulus (G'/ρ) along the grain (3), as well as their corresponding damping coefficients (tanδ3, tanδG). This analysis was done for native and then for extracted wood. Interlocked grain resulted in 0-25° GA and in variations of a factor 2 in E'L/ρ and tanδL. Along the grain, Padauk wood was characterized, as compared to typical hardwoods, by a somewhat lower E'3/ρ and elastic anisotropy (E'/G'), due to a wide microfibril angle plus a small weight effect of extracts; and a very low tanδ3 and moderate damping anisotropy (tanδG/tanδ3). Extraction affected mechanical parameters in the order: tanδ3 ≈ tanδG > G'/ρ >> E'3/ρ. That is, extractives' effects were nearly isotropic on damping but clearly anisotropic on storage moduli.
ISSN: 0043-7719

hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382/document
https://hal.archives-ouvertes.fr/hal-00544382/file/Identification_anisotropic_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0348-0