Éditeur(s) : Elsevier
Résumé : We present results from multibeam bathymetric data acquired during 2005 and 2006, in the region of maximum slip of the 26 Dec. 2004 earthquake (Mw 9.2). These data provide high-resolution images of seafloor morphology of the entire NW Sumatra forearc from the Sunda trench to the submarine volcanic arc just north of Sumatra. A slope gradient analysis of the combined dataset accurately highlights those portions of the seafloor shaped by active tectonic, depositional and/or erosional processes. The greatest slope gradients are located in the frontal 30 km of the forearc, at the toe of the accretionary wedge. This suggests that long-term deformation rates are highest here and that probably only minor amounts of slip are accommodated by other thrust faults further landward. Obvious N-S oriented lineaments observed on the incoming oceanic plate are aligned sub-parallel to the fracture zones associated with the Wharton fossil spreading center. Active strike-slip motion is suggested by recent deformation with up to 20-30 m of vertical offset. The intersection of these N-S elongated bathymetric scarps with the accretionary wedge partly controls the geometry of thrust anticlines and the location of erosional features (e.g. slide scars, canyons) at the wedge toe. Our interpretation suggests that these N-S lineaments have a significant impact on the oceanic plate, the toe of the wedge and further landward in the wedge. Finally, the bathymetric data indicate that folding at the front of the accretionary wedge occurs primarily along landward-vergent (seaward-dipping) thrusts, all unusual style in accretionary wedges worldwide. The N-S elongated lineaments locally act as boundaries between zones with predominant seaward versus landward vergence.
Earth and Planetary Science Letters (0012-821X) (Elsevier), 2008-11 , Vol. 275 , N. 3-4 , P. 201-210

Droits : 2008 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/2008/publication-5166.pdf
DOI:10.1016/j.epsl.2008.04.053
http://archimer.ifremer.fr/doc/00000/5166/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We have performed tri-axial compression experiments on olivine aggregates at 900 °C and at a confining pressure of 300 MPa in a high-resolution gas-medium mechanical testing apparatus. Deformation at two different constant strain rates (1.1 × 10− 5 s− 1 and 3.4 × 10− 4 s− 1) yields continuous hardening, reaching maximal differential stresses of 930 and 1076 MPa, respectively, before sample failure at ca. 10% strain. The deformed samples were characterized by electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). Crystallographic preferred orientations (CPO) are weak but reveal an alignment of the [010] axes around the compression direction and some concentration of [001] and [100] axes normal to it. TEM observations confirm plastic deformation by dislocation glide, with both [001] and [100] Burgers vectors. Electron tomography, performed for the first time on deformed fined-grained olivine, shows that [001] dislocations glide extensively on {110} and {130} planes, in complement to the (010) and (100) glide planes often reported at high temperatures. [100] dislocations glide mostly on (010), but {011} and {041} planes are also activated. The experimental CPO and relative activity of slip systems are well reproduced by viscoplastic self-consistent simulations in which all [100] and [001] slip systems have similar strengths. They are also consistent with olivine CPO from natural samples deformed at low temperature. Comparison of the present mechanical results to those obtained for olivine single-crystals at similar conditions shows that at low temperature (below 1100 °C) and high stress (> 300 MPa) polycrystalline olivine has a more complex mechanical behavior than single crystals. However, both datasets advocate for a much weaker dry mantle lithosphere than previously thought.
ISSN: 0040-1951

hal-01053513
https://hal.archives-ouvertes.fr/hal-01053513
DOI : 10.1016/j.tecto.2014.03.022

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
Surface displacements due to temporal changes in environmental mass redistributions are observable in the coordinate time series of many Global Navigation Satellite System (GNSS) sites. In this study, we investigated the effect of loading on estimates of tectonic velocity computed from campaign-style GNSS observations. The study region is in the Pyrenees mountain range between France and Spain (ResPyr campaigns). In this area, seismic activity is continuous and moderate and the expected amplitude of the horizontal tectonic velocity is less than 0.5 mm/yr. In order to determine the velocity, 4 sparse GNSS campaigns were carried out from 1995 to 2010. Considering this small rate of deformation, loading phenomena can contribute a non-negligible artifact to the velocity computation that could affect our geodynamical interpretation. In this investigation, we specifically considered the atmospheric, hydrological, and non-tidal ocean loading phenomena. The computed loading deformations for this region show the horizontal displacements are dominated by the non-tidal ocean loading (maximum 4 mm for the North and 3.1 mm for the East components); the main vertical contributions are due to the atmospheric and continental water storage loading (maximum 14.3 for the atmosphere and 8.1 mm for the hydrology, respectively). We have found that the dominant loading effect on the horizontal velocity is the non-tidal ocean loading (mean of 0.11 mm/yr), whereas the vertical component is dominated by the hydrological loading (mean of 0.21 mm/yr). Since the study area is in a mountainous region, we also analyzed the difference between the atmospheric and the topography dependent atmospheric loading models at our GNSS campaign sites. We did not find any significant difference between the two atmospheric loading models in terms of horizontal velocity. Finally, we performed simulations to identify the optimum timing and frequency of future GNSS campaigns in this area that would minimize the loading effects on tectonic velocity estimates.
ISSN: 0039-3169

hal-00963629
https://hal.archives-ouvertes.fr/hal-00963629
DOI : 10.1007/s11200-012-0458-2

Éditeur(s) : HAL CCSD
Résumé : The Franceville Basin (2.1 Ga) in southeastern Gabon, hosts a black shale series well preserved (FB Formation) which represents an exceptional example of unmetamorphised Paleoproterozoic sediment strata. This basin includes the protore of one of the largest Mn-oxide laterite ore worldwide, mined by Eramet-Comilog. The aim of this this work is to determine formation conditions of this protore and to characterize the global sedimentary evolution of the FB Formation which include the protore. This 75 m thick protore is constituted of Mn carbonate-rich black shales which represent a potential ore deposit for the future. It was drilled, on the Bangombé plateau, during a recent campaign of 24 boreholes with an average depth of 125 m.Through multidisciplinary study on these cores and key outcrops of the basin, this work focuses on : i) the depositional environment of the Mn-protore and FB Formation ; ii) the processes of formation of the Mn-carbonates at 2.1 Ga and iii) the architecture and distribution of Mn-rich levels of the protore on the Bangombé Plateau.A detailed sedimentological and petrological study allowed us to redefine the division of the FB into nine units, named U1 to U9 from the base to the top. These units show a fine upward cycle up to U5 and a reverse coarse loop until U9. This division leads to a new interpretation to propose an evolution from a shoreface depositional environment controlled by deltaic currents (U1) to an offshore depositional environment with anoxic conditions (U2). In this basin, a system of submarine fan is developed, feeding a network of sand injections (injectites) covering the Bangombé plateau (70 km²) and with a thickness of 150 m affecting U4 to U7, including the Mn-protore. The protore depositional environment formed below the wave base limit (U4, U5 and U6) in a starved basin, controlled by biochemical sedimentation allowed the formation of Mn-carbonates. The end of starved basin, would allow the re-opening of the detrital input into the offshore basin (U7). This basin is then filled by storm bar deposits intersected by deltaic sub-aquatic channels (U8). The U9 unit corresponds to a quiet lagoon environment, allowing the multicellular organism development for the first time on the planet.A geochemical study allowed the characterization of the depositional environment of Mn-carbonates as an anoxic to sub-oxic and alkaline environment. For the first time, we showed that the manganese carbonates, present as bacteriomorph forms, are precipitated from the seawater by the mediated photosynthetic cyanobacterial activity, which allows CO2 / HCO3 depression of the environment and a local increase of pH. The cyanobacterial activity is controlled by the absence of bottom currents, which increase the detrital input. This would stop the activity of the cyanobacteria and thus would lead to the decrease of the Mn-concentration along the protore.Finally, well-log and a sequential correlation analyses allowed us to detail spatial and timing repartition of FB Formation deposit, controlled by a tectono-sedimentary model. We propose two- tectono-sedimentary phases. A first syn-tectonic phase (U1 to U3) controls the depocentres and sedimentation gaps. Turbidite coarse deposits are located in the most subsident part, clay deposits rather on the slope and carbonates on shoals. A second post-tectonic phase (U4 to U7) allows isopach deposits. The Mn-protore formed during the post-tectonic phase. However, it shows a variable thickness due to subsidence to the north of the Bangombé plateau. So, on the Bangombé plateau, Mn-contents increase towards the south, whereas the protore thickness increases towards the NNE. Moreover sand injectites decrease Mn-content in the eastern part of the Bangombé plateau and impact on the economic evaluation of the Mn-carbonates. Currently, the protore is structured by post-sedimentary faults, which lead to a non-continuity of the high Mn levels on the Bangombé plateau.
Le Bassin de Franceville situé au SE du Gabon présente une série de black shales (Formation FB) d'âge Paléoprotérozoïque (2,1 Ga) surmontant les grès de la Formation FA. Ce bassin peu déformé et non métamorphique représente une archive exceptionnelle des processus de dépôt de cette période de l’histoire de la Terre où la vie commence à se développer. En particulier, la Formation FB contient le protore d'un gisement mondial d'oxydes de manganèse exploité par la société Eramet-Comilog. L’objectif de ce travail est de préciser les conditions de formation de ce protore et de le replacer dans l’histoire du remplissage du bassin. Ce protore d'une épaisseur moyenne de 75 m est constitué de carbonates de manganèse ; il a fait l'objet d'une récente campagne de 24 forages carottés d'une profondeur moyenne de 125 m sur le plateau de Bangombé.A travers une approche pluridisciplinaire comprenant l'étude de ces forages et des affleurements clefs du bassin, ce travail porte sur la caractérisation i) de l'environnement de dépôt du protore et des séries qui l'encadrent (du toit du FA au toit du FB) ; ii) du mode de formation des carbonates de Mn à 2,1 Ga et iii) de l'architecture et de la répartition des hautes teneurs en Mn du protore qui représente un gisement potentiel du futur.L’étude pétro-sédimentaire détaillée a permis de distinguer neuf unités (U1 à U9) au sein de la Formation FB organisées suivant un cycle rétrogradant jusqu’à U5 puis progradant jusqu’à U9. Ce découpage montre une évolution du milieu de dépôt depuis un domaine de shoreface contrôlé par des courants deltaïques (U1) évoluant vers des dépôts d’offshore restreint (U2). Ce bassin enregistre ensuite un système de chenaux-levées turbiditiques (U3) qui alimentent un réseau d'injectites reconnu sur l’ensemble du Pl. de Bangombé et qui traverse 150 m de série (U4 à U7) en affectant le protore et ainsi les teneurs en Mn. L'environnement de dépôt du protore (U5 et U6) marque l’isolement du bassin qui devient affamé et contrôlé par une sédimentation biochimique à l’origine du dépôt des carbonates de Mn. L'Unité 7 correspond à la réouverture des apports détritiques en domaine d'offshore supérieur puis en domaine de shoreface dominé par des dépôts de tempêtes et de chenaux sous-aquatiques deltaïques (U8), et enfin lagunaire (U9) dans lequel apparaissent les premiers métazoaires de l’histoire de la planète, suivant une séquence régressive.Une étude géochimique a permis de préciser les conditions de dépôt du protore qui se forme en milieu alcalin anoxique à sub-oxique. Dans ce milieu, nous montrons pour la première fois une précipitation directe des carbonates de Mn sous forme bactériomorphe induite par l'activité photosynthétique des cyanobactéries qui consomment le CO2/HCO3 et conduisent à une augmentation du pH favorable à la formation des carbonates de Mn. L'activité cyanobactérienne est conditionnée par l’absence de courants de fond qui augmentent la turbidité du milieu et stoppent cette dernière.Les corrélations diagraphiques et séquentielles permettent de préciser la répartition spatiale et temporelle du FB permettant ainsi de replacer le protore dans l’histoire tectono-sédimentaire du bassin. Une première phase syn-tectonique (U1 à U3) contrôle l’épaisseur et la mise en place de dépôts turbiditiques dans les parties subsidentes, de dépôts argileux sur les pentes et de dépôt de carbonates sur les hauts-fonds. La seconde phase post tectonique (U4 à U7) permet la mise en place de dépôts relativement isopaques, bien que le protore enregistre une subsidence plus importante au nord du Pl. de Bangombé. On observe ainsi, sur le Plateau de Bangombé, des teneurs en Mn qui augmentent vers le sud alors que l’épaisseur du protore augmente vers le NNE. Postérieurement au dépôt du FB, le protore est structuré par des failles qui le compartimentent en touches de piano limitant ainsi sa continuité sur le Plateau de Bangombé.
https://hal.archives-ouvertes.fr/tel-01621460

tel-01621460
https://hal.archives-ouvertes.fr/tel-01621460
https://hal.archives-ouvertes.fr/tel-01621460/document
https://hal.archives-ouvertes.fr/tel-01621460/file/these_Dubois2017-MnGabon.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This work combines structural and geochronological data to improve our understanding of the mechanical behaviour of continental crust involving large amount of magma or partially melted material in an abnormally hot collisional belt. We performed a magnetic and geochronological (U/Pb) study on a huge tonalitic batholith from the Neoproterozoic Araçuaí belt of East Brazil to determine the strain distribution through space and time. Anisotropy of magnetic susceptibility, combined with rock magnetism investigations, supports that the magnetic fabric is a good proxy of the structural fabric. Field measurements together with the magnetic fabrics highlight the presence in the batholith of four domains characterized by contrasted magmatic flow patterns. The western part is characterized by a gently dipping, orogen-parallel (∼NS) magmatic foliation that bears down-dip lineations, in agreement with westward thrusting onto the São Francisco craton. Eastward, the magmatic foliation progressively turns sub-vertical with a lineation that flips from sub-horizontal to sub-vertical over short distances. This latter domain involves an elongated corridor in which the magmatic foliation is sub-horizontal and bears an orogen-parallel lineation. Finally the fourth, narrow domain displays sub-horizontal lineations on a sub-vertical magmatic foliation oblique (∼N150°E) to the trend of the belt. U/Pb dating of zircons from the various domains revealed homogeneity in age for all samples. This, together with the lack of solid-state deformation suggests that: 1) the whole batholith emplaced during a magmatic event at ∼580 Ma, 2) the deformation occurred before complete solidification, and 3) the various fabrics are roughly contemporaneous. The complex structural pattern mapped in the studied tonalitic batholith suggests a 3D deformation of a slowly cooling, large magmatic body and its country rock. We suggest that the development of the observed 3D flow field was promoted by the low viscosity of the middle crust that turned gravitational force as an active tectonic force combining with the East-West convergence between the São Francisco and Congo cratons.
ISSN: 0191-8141

hal-00745696
https://hal.archives-ouvertes.fr/hal-00745696
DOI : 10.1016/j.jsg.2012.02.015

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
The Ama Drime range located at the transition between the high Himalayan range and south Tibet is a N-S active horst that offsets the South Tibetan Detachment System (STDS). Within the horst, a paragneissic unit, possibly attributed to the upper Himalayan crystalline series, overly the lower Himalayan crystalline series Ama Drime orthogneissic unit containing large metabasite layers and pods that have experienced pressure >= 1.4 GPa. Combining structural analysis with new and published pressure-temperature (P-T) estimates as well as U-Th/Pb, Ar-39/Ar-40 and (U-Th)/He ages, the P-T-deformation-time (P-T-D-t) paths of the main units within and on both sides of the horst are reconstructed. They imply that N-S normal faults initiated prior to 11 Ma and have accounted for a total exhumation <= 0.6 GPa (22 km) that probably occurred in two phases: the first one until similar to 9 Ma and the second one since 6 to 4 Ma at a rate of similar to 1 mm/yr. In the Ama Drime unit, 1 to 1.3 GPa (37 to 48 km) of exhumation occurred after partial melting since similar to 30 Ma until similar to 13 Ma, above the Main Central Trust (MCT) and below the STDS when these two fault systems were active together. The switch from E-W (STDS) to N-S (Ama Drime horst) normal faulting between 13 and 12 Ma occurs at the time of propagation of thrusting from the MCT to the Main Boundary Thrust. These data are in favor of a wedge extrusion or thrust system rather than a crustal flow model for the building of the Himalaya. We propose that the kinematics of south Tibet Cenozoic extension phases is fundamentally driven by the direction and rate of India underthrusting.
ISSN: 0278-7407

hal-00486405
https://hal.archives-ouvertes.fr/hal-00486405
DOI : 10.1029/2009TC002551

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Seismic anisotropy originating within the continental crust is used to determine kinematic flow lines within active mountain belts and is widely attributed to regionally aligned mica. However, naturally deformed micaceous rocks commonly show composite (e.g. S-C) fabrics. It is necessary therefore to understand how both varying mica content and differing intensities of multiple foliations impact on seismic interpretations in terms of deformation fields. An outcrop analogue for granitic mid-crustal deformed zones is used here to calibrate the seismic response against both parameters. Seismic responses are modelled using crystallographic preferred orientations for polymineralic, micaceous granitic gneisses, measured using Electron Back-Scatter Diffraction. The sample results are generalised by modelling the effects of variations in modal composition and the relative importance of deformation fabrics of variable orientation, so-called rock and fabric recipes. The maximum P- and S-anisotropy are calculated at 16.6% and 23.9% for single-foliation gneisses but for mixed (i.e. S-C) foliation gneisses these values reduce to 5.8% and 7.5% respectively. Furthermore, mixtures of multiple foliations generate significant variations in the geometry of the seismic anisotropy. This effect, coupled with the geographical orientation of fabrics in nature. can generate substantial variations in the orientation and magnitude of seismic anisotropy (especially for shear waves) as measured for the continental crust using existing receiver function and teleseismic near-vertical incidence methods. Thus, maps of seismic anisotropy varying with depth in deforming continents need not imply necessarily depth-varying deformation kinematics and tectonic decoupling.
ISSN: 0012-821X

hal-00445247
https://hal.archives-ouvertes.fr/hal-00445247
DOI : 10.1016/j.epsl.2009.09.035

Éditeur(s) : HAL CCSD
Résumé : This work provides new constraints on the interactions between deformation and percolation of melt or fluids, as well as on the implications of these processes for the seismic properties of the mantle wedge. It is based on the analysis of spinel peridotites from the massif of Ronda (Spain) and two xenolith suites from active subduction zones (Kamchatka, Papua New Guinea). A coupled structural, petrological and geochemical study of these samples shows that they underwent a reactive percolation of melts or Si-rich fluids, which was synchronous to a deformation event occurring under high temperature and low stress conditions, consistent with the PT conditions at the base of the lithosphere or in the asthenosphere. This reactive percolation is responsible for enrichment in pyroxenes, mainly orthopyroxene, which is often localized in bands parallel to the high-temperature foliation. This enrichment is associated with grain size reduction and dispersion of the crystallographic orientation of olivine. The dominant slip system in olivine is {0kl}[100], which results in fast S-wave polarization parallel to the flow direction in the mantle. The decrease in the intensity of the olivine crystal preferred orientations associated with the enrichment in pyroxene results in significant decrease of the anisotropy that may induce an underestimation of the thickness of the anisotropic layer by up to 33%. The observed orthopyroxene enrichment also lowers the Vp/Vs ratio, but cannot explain Vp/Vs < 1.7 mapped locally in the fore-arc mantle in Japan and the Andes. Such low Vp/Vs ratios may however be explained by considering the intrinsic anisotropy of the peridotites, which is generally ignored in large-scale Vp/Vs ratio mapping of the mantle wedge. Infrared analyses show that olivine from the both xenolith collections contains less water than the theoretical saturation calculated for their estimated equilibrium temperature in the spinel stability field. These low water content are similar to those observed in spinel peridotites from other subduction zones and probably record both the low solubility of water in olivine at relatively low pressure and dehydration during exhumation of the xenoliths. These measured water contents as well as theoretical saturation estimations are not sufficient to change the dominant slip direction of in olivine from [100] to [001].
Ce travail apporte de nouvelles contraintes sur les interactions entre déformation et processus d'hydratation et de percolation de magma ou de fluides dans le manteau à l'aplomb d'une zone de subduction et leurs implications sur les propriétés sismiques dans le coin mantellique. Il se base sur l'analyse de péridotites à spinelle provenant du massif de Ronda (Espagne) et deux séries de xénolites issues de zones de subduction actives (Kamchatka, Papouasie-Nouvelle-Guinée). L'étude structurale, pétrologique et géochimique de ces échantillons montrent qu'ils ont subit une percolation réactive de magma ou de fluide synchrone d'une déformation de haute température basse contrainte cohérente avec les condition PT de la base de la lithosphère ou de l'asthénosphère. Cette percolation réactive est responsable d'un enrichissement en pyroxènes, qui est souvent localisé dans des bandes parallèles à la foliation. Cet enrichissement est associé à une dispersion de l'orientation cristallographique de l'olivine. Les systèmes de glissement dominant dans l'olivine sont dans tous les cas {0kl}[100], ce qui implique que la direction de polarisation rapide des ondes S dans la partie supérieure du coin mantellique est parallèle à la direction d'écoulement dans le manteau. La décroissance de l'intensité des OPR de l'olivine associée à l'enrichissement en pyroxènes a pour conséquence une réduction non négligeable de l'anisotropie sismique qui peut induire jusqu'à 33% d'erreur sur l'interprétation de l'épaisseur de la couche anisotrope. Un enrichissement en orthopyroxène peut aussi entraîner une baisse du rapport Vp/Vs, mais ne peut expliquer les rapports Vp/Vs <1,7 cartés dans certains avant-arcs. Cependant de telles valeurs peuvent être expliquées si l'anisotropie des péridotites du coin mantellique est prise en compte. Les analyses par spectroscopie infra-rouge montrent que les olivines des deux séries de xénolites étudiées contiennent moins d'eau que la saturation théorique calculée pour leurs températures d'équilibre dans le domaine du spinelle. Ces faibles concentrations en eau sont similaires à celles observées dans les olivines des péridotites à spinelle des autres zones de subduction. Elles enregistrent probablement la faible solubilité de l'eau dans l'olivine à des pressions relativement basses et la déshydratation au cours de l'exhumation des xénolites. Ces teneurs en eau mesurées ainsi que les estimations de la saturation théorique ne sont pas suffisantes pour changer la direction de glissement dominante dans l'olivine de [100] à [001].
https://tel.archives-ouvertes.fr/tel-00689832

tel-00689832
https://tel.archives-ouvertes.fr/tel-00689832
https://tel.archives-ouvertes.fr/tel-00689832/document
https://tel.archives-ouvertes.fr/tel-00689832/file/These-Soustelle2010.pdf

Éditeur(s) : HAL CCSD Society of Economic Geologists
Résumé : International audience
The ~8-Moz Sadiola Hill gold deposit is located in the Kédougou-Kénieba inlier, a window of deformed ca. 2200 to 2050 Ma rocks that crop out in eastern Senegal and western Mali. The geology of the inlier differs from other Paleoproterozoic granite-greenstone belts and sedimentary basins by the abundance of carbonate rocks. The Sadiola Hill gold deposit occurs within 3 km of the Senegal-Mali shear zone, and country rocks in the region have undergone polycyclic deformation. The lithostratigraphy of the open pit consists of impure limestones overlain by younger sequences of detrital sedimentary rocks, which include arenite, wacke, and siltstone. The sedimentary rocks have been subjected to regional greenschist-facies metamorphism and have been intruded by multiple generations of synkinematic, calc-alkaline stocks and dikes. The bulk of the ore is hosted within a N-S- to NNW-trending, 10- to 50-m-wide, brittle-ductile dilational shear zone defined as the Sadiola shear zone. Gold lodes also occur along an array of steep NNE-trending shear zones. Geometric and kinematic analyses indicate that the ore-hosting structures were undergoing sinistral displacement at the time of mineralization, locally defined as the D3s NNW-SSE-shortening event. Hydrothermal alteration is polyphase and includes an early high-temperature calc-silicate phase (i.e., porphyroblastic growth of actinolite-tremolite) followed by a potassic phase (i.e., biotite-calcite-quartz ± K-feldspar-tourmaline-actinolite) that was synchronous with ore mineral deposition. Paragenetic studies reveal a multistage ore development that includes an As-rich sulfide stage, followed by an Au-Sb stage. The ore is associated with a metal enrichment suite of Au-As-Sb ± Cu-Fe-W-Mo-Ag-Bi-Zn-Pb-Te. The Sadiola Hill deposit shares a similar relative timing and structural setting to that of other world-class orogenic gold systems in the West African craton (e.g., Ashanti, Loulo), with gold deposition occurring during a period of transcurrent tectonics, after the cessation of region-wide compressional deformation. The high-temperature paragenesis at Sadiola Hill is atypical of gold mineralization in the craton and indicates that the late Eburnean tectono-magmatic activity between ca. 2080 and 2060 Ma played an important role in the dynamics of hydrothermal fluid circulation along the Senegal-Mali shear zone.
ISSN: 0361-0128

hal-01583358
https://hal.archives-ouvertes.fr/hal-01583358
DOI : 10.2113/econgeo.112.1.23

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Gibraltar arc, spans a complex portion of the Africa-Eurasia plate boundary marked by slow oblique convergence and intermediate and deep focus seismicity. The seemingly contradictory observations of a young extensional marine basin surrounded by an arcuate fold-and-thrust belt, have led to competing geodynamic models (delamination and subduction). Geophysical data acquired in the past decade provide a test for these models and support a narrow east-dipping, subduction zone. Seismic refraction studies indicate oceanic crust below the western Gulf of Cadiz. Tomography of the upper mantle reveals a steep, east-dipping high P-wave velocity body, beneath Gibraltar. The anisotropic mantle fabric from SKS splitting shows arc-parallel "fast directions", consistent with toroidal flow around a narrow, westward retreating subducting slab. The accompanying WSW advance of the Rif-Betic mountain belt has constructed a thick pile of deformed sediments, an accretionary wedge, characterized by west-vergent thrust anticlines. Bathymetric swath‐mapping images an asymmetric embayment at the deformation front where a 2 km high basement ridge has collided. Subduction has slowed significantly since 5 Ma, but deformation of recent sediments and abundant mud volcanoes suggest ongoing activity in the accretionary wedge. Three possible origins for this deformation are discussed; gravitational spreading, overall NW-SE convergence between Africa and Iberia and finally a WSW tectonic push from slow, but ongoing roll-back subduction. In the absence of arc volcanism and shallow dipping thrust type earthquakes, evidence in favor of present-day subduction can only be indirect and remains the object of debate. Continued activity of the subduction offers a possible explanation for great (M > 8.5) earthquakes known to affect the area, like the famous 1755 Great Lisbon earthquake. Recent GPS studies show SW motion of stations in N Morocco at velocities of 3-6 mm/yr indicating the presence of an independent block, a "Rif-Betic-Alboran" microplate, situated between Iberia and Africa.
ISSN: 0040-1951

insu-00769762
https://hal-insu.archives-ouvertes.fr/insu-00769762
DOI : 10.1016/j.tecto.2012.08.038

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Detailed structural and petrological mapping in the Beni Bousera peridotite (Rif Belt, northern Morocco) shows that this orogenic peridotite massif is composed of four tectono-metamorphic domains with consistent kinematics, marked by a pervasive, shallowly dipping foliation with a NW-SE stretching lineation that progressively rotates towards a NNE-SSW orientation in the lowermost part of the massif. From top to bottom, these domains are garnet-spinel mylonites, Ariègite subfacies fine-grained porphyroclastic spinel peridotites, Ariègite-Seiland subfacies porphyroclastic, and Seiland subfacies coarse-porphyroclastic to coarse-granular spinel peridotites. Microstructures and crystal preferred orientations point to deformation dominantly by dislocation creep in all domains, but the continuous increase in average olivine grain size indicates decreasing plastic work rates from top to bottom. This evolution in deformation conditions is consistent with the change in synkinematic pressure and temperature conditions, from 900°C at 2*0 GPa in garnet-spinel mylonites to 1150°C at 1*8 GPa in the Seiland domain. A pervasive diffuse dunitic-websteritic layering subparallel to the foliation suggests deformation in the presence of melt in the Seiland domain. Gravitational instabilities owing to local melt accumulation may account for <200 m wide areas exhibiting a vertical lineation in this domain. To account for the consistent kinematics and the tectono-metamorphic evolution, which implies a temperature gradient of c. 125°C km−1 preserved across the Beni Bousera massif, we propose that the entire massif records the functioning of a low-angle shear zone, a few kilometres wide, which accommodated exhumation of the base of the lithosphere from ∼90 to ∼60 km depth. Partial melting in the Seiland domain may be explained by fast decompression of the footwall, without the need for exotic heat sources. Moreover, if the present-day orientation of the shear zone is similar to that when it was active in the mantle, the stretching lineations at high angle to the metamorphic gradient imply that shearing parallel to the trend of the belt accompanied thinning; that is, a transtensional deformation of the margin.
ISSN: 0022-3530

hal-00950056
https://hal.archives-ouvertes.fr/hal-00950056
DOI : 10.1093/petrology/egt067

Éditeur(s) : HAL CCSD
Résumé : The purpose of this work is to specify the deformation offshore East of Taiwan by characterizing major active faults in particular at the level of the Ryukyu forearc. The major problem associated with the study of this region is that earthquakes are located outside the permanent networks. Consequently, this led to some unprecise earthquake locations limiting tectonic and statistical analyses, and therefore the correct estimation of the seismic hazard. This work is included in the project ANR ACTS (Active Tectonics and Seismic Hazard in Taiwan). To achieve this goal, we worked on three different timescales for which a different localization method has been proposed to obtain a clear image of seismic deformation and highlight major faults offhore East of Taiwan. First, at the scale of the century (from the analysis of a seismicity catalogue with homogeneous magnitude), the instrumental historical earthquakes (1897-2007) show that the Ryukyu margin was affected by 6 earthquakes of magnitude greater than 7 with 4 of them for which the responsible fault is unknown. We propose a method of relative location to relocate the historic events from the time difference of P and S arrival times (Ts-Tp) at each station. The location is obtained by searching for "analogue" earthquakes in the recent instrumental catalogue (1991-2008) for which Ts-Tp at each station is close. This method has been applied to the largest (in terms of magnitude) earthquake ever recorded in Taiwan, the earthquake of June 5, 1920 (M7.7 +/- 0.2). A rupture along the interplate of the Ryukyu subduction with a possible nucleation at the downdip limit of a splay-fault is certainly responsible of this earthquake. Then, at the scale of the decade, the improvement of the method of absolute location based on MAXimum of Intersection of EDT (MAXI, EDT: Equal Differential Time) allows to better extract the erroneous arrival times and prevents the "trade-off" between depth and origin time, and between depth and epicentral position when the azimuthal coverage is low (gap Azimuthal > 180degre). Synthetic tests show the effectiveness of MAXI (using P-wave only) to determine the parameters x, y and z even when the azimuthal gap is important. In the latter case, the quality of the results is dependent on the velocity model to represent the 3D structure of the Earth. We propose an approach involving the use of a 3D a priori P-wave velocity model to locate earthquakes which are lateral and remote to the seismic network. An application to the case of Taiwan and Ecuador validates this approach. Finally, at the level of a few months, the marine geophysical campaign RATS (Ryukyu Arc: Tectonics and Seismology) was conducted in two stages. A passive seismology experiment from July to October, 2008 (RATS1) has been conducted over the forearc of the Ryukyus and then active seismic experiment (refraction and reflection) was conducted in May 2009 in a NNE - SSW line through the Ryukyu margin. These two combined experiments allow improving our knowledge about the crustal structure of the margin. At the level of the forearc, the basement of the forearc is characterized by vertical backstop and a very deformed basis certainly associated with a significant out of sequence deformation. In depth, the downgoing plate is certainly affected by a tear that controls the seismicity in the region of transition between the subduction and collision.
Le but de ce travail est de préciser la déformation en mer à l'est de Taïwan et de notamment caractériser les failles actives majeures en particulier au niveau de l'avant-arc des Ryukyus. Le problème majeur associé à l'étude de cette région est que les séismes sont localisés en dehors des réseaux permanents et que cela conduit à des localisations peu précises limitant les analyses statistiques, tectoniques et donc l'estimation correcte de l'aléa sismique. Ce travail est inclus dans le projet ANR ACTS (Active Tectonics and Seismic Hazard in Taiwan). Pour atteindre cet objectif, nous travaillons à trois échelles de temps différentes pour lesquelles une méthode de localisation différente a été proposée pour obtenir une image précise de la déformation sismique et mettre en évidence les failles majeures en mer à l'est de Taïwan. D'abord, à l'échelle du siècle (à partir de l'analyse d'un catalogue de sismicité homogène en magnitude), les séismes historiques instrumentaux (1897-2007) montrent que la marge des Ryukyus a été affectée par 6 séismes de magnitude supérieure à 7 dont 4 pour lesquels la faille responsable n'est pas connue. Nous proposons une méthode de localisation relative qui permet de relocaliser les évènements historiques à partir des différences de temps d'arrivées P et S (Ts-Tp) à chaque station. La localisation est obtenue en recherchant les séismes analogues dans le catalogue instrumental récent (1991-2008) pour lesquels Ts-Tp à chaque station est proche. Cette méthode a été appliquée au plus gros séisme (en terme de magnitude) jamais enregistré à Taïwan, le séisme du 5 juin 1920 (M7.7 $pm$ 0.2). Ce séisme a certainement pour origine une rupture sur l'interplaque sismogène de la subduction des Ryukyus avec une possible nucléation à la base d'une faille hors-séquence. Ensuite, à l'échelle de la dizaine d'années, l'amélioration de la méthode de localisation absolue du MAXimum d'Intersection EDT (MAXI, EDT: Equal Differential Time) permet de mieux extraire les temps d'arrivées erronés et empêche les "trade-off" entre profondeur et temps d'origine et, entre profondeur et position épicentrale lorsque la couverture azimutale est faible (gap azimutal > 180°). Des tests synthétiques montrent l'efficacité de MAXI (en utilisant les ondes P uniquement) à déterminer les paramètres x, y et z même lorsque le gap azimutal est important. Dans ce dernier cas, la qualité des résultats reste dépendant du modèle de vitesse à représenter la structure 3D de la Terre. Nous proposons une démarche associant l'utilisation d'un modèle de vitesse des ondes P 3D a priori avec la méthode MAXI pour localiser les séismes qui sont latéraux et éloignés du réseau. Une application au cas de Taïwan et en Équateur valide cette approche. Enfin, à l'échelle de quelques mois, la campagne de géophysique marine RATS (Ryukyu Arc: Tectonics and Seismology) a été menée en deux temps. Une expérience de sismologie passive de juillet à octobre 2008 (RATS1) a été menée au-dessus de l'avant-arc des Ryukyus puis une expérience de sismique active (réfraction et réflexion) a été menée en mai 2009 sur une ligne NNE-SSW à travers la marge des Ryukyus. Ces deux expériences combinées permettent d'améliorer notre connaissance de la structure crustale de la marge. Au niveau de l'avant-arc, le socle de l'avant-arc est caractérisé par une extrémité formant un butoir vertical et une base très déformée certainement associée à une importante déformation hors-séquence. En profondeur, la plaque plongeante est certainement affectée par une déchirure qui contrôle la sismicité dans cette région de transition entre la subduction et la collision.
https://tel.archives-ouvertes.fr/tel-00660737

tel-00660737
https://tel.archives-ouvertes.fr/tel-00660737
https://tel.archives-ouvertes.fr/tel-00660737/document
https://tel.archives-ouvertes.fr/tel-00660737/file/Thesis_small.pdf

Éditeur(s) : HAL CCSD MAIK Nauka/Interperiodica
Résumé : Interaction between surface processes and deep tectonic processes plays a key role in the structural evolution, kinematics and exhumation of rocks in orogenic wedges. The deformation patterns observed in analogue models applied to natural cases of present active or ancient mountain belts reflect several first order processes that result of these interactions. Internal strain partitioning due to mechanical behaviour of a thrust wedge has a strong impact on the vertical component of displacement of tectonic units that in return favour erosion in domains of important uplift. Such strain partitioning is first controlled by tectonic processes, but surface processes exert a strong feed back on wedge dynamics. Indeed, material transfer in thrust wedges not only depends on its internal dynamics, it is also influenced by climate controlled surface processes involving erosion and sedimentation. Effects of erosion are multiple: they allow long term localization of deformed domains, they favour important exhumation above areas of deep underplating and combined with sedimentation in the foreland they contribute to maintain the wedge in a critical state for long time periods. The simple models illustrate well how mountain belts structure, kinematics of tectonic units and exhumation are determined by these complex interactions.
ISSN: 0016-8521

hal-00561361
https://hal.archives-ouvertes.fr/hal-00561361
DOI : 10.1134/S0016852110060075

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Although magmatism may occur during the earliest stages of continental rifting, its role in strain accommodation remains weakly constrained by largely 2-D studies. We analyze seismicity data from a 13 month, 39-station broadband seismic array to determine the role of magma intrusion on state-of-stress and strain localization, and their along-strike variations. Precise earthquake locations using cluster analyses and a new 3-D velocity model reveal lower crustal earthquakes beneath the central basins and along projections of steep border faults that degas CO2. Seismicity forms several disks interpreted as sills at 6-10 km below a monogenetic cone field. The sills overlie a lower crustal magma chamber that may feed eruptions at Oldoinyo Lengai volcano. After determining a new ML scaling relation, we determine a b-value of 0.87±0.03. Focal mechanisms for 65 earthquakes, and 13 from a catalogue prior to our array reveal an along-axis stress rotation of ∼60° in the magmatically active zone. New and prior mechanisms show predominantly normal slip along steep nodal planes, with extension directions ∼N90°E north and south of an active volcanic chain consistent with geodetic data, and ∼N150°E in the volcanic chain. The stress rotation facilitates strain transfer from border fault systems, the locus of early-stage deformation, to the zone of magma intrusion in the central rift. Our seismic, structural, and geochemistry results indicate that frequent lower crustal earthquakes are promoted by elevated pore pressures from volatile degassing along border faults, and hydraulic fracture around the margins of magma bodies. Results indicate that earthquakes are largely driven by stress state around inflating magma bodies.
ISSN: 1525-2027

hal-01667198
https://hal.archives-ouvertes.fr/hal-01667198
DOI : 10.1002/2017GC007027

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Gulf of Cadiz lies astride the complex plate boundary between Africa and Eurasia west of the Betic-Rif mountain belt. We report on the results of recent bathymetric swathmapping and multi-channel seismic surveys carried out here. The seafloor is marked by contrasting morphological provinces, spanning the SW Iberian and NW Moroccan continental margins, abyssal plains and an elongate, arcuate, accretionary wedge. A wide variety of tectonic and gravitational processes appear to have shaped these structures. Active compressional deformation of the wedge is suggested by folding and thrusting of the frontal sedimentary layers as well as basal duplexing in deeper internal units. There is evidence for simultaneous gravitational spreading occurring upslope. The very shallow mean surface and basal slopes of the accretionary wedge (1° each) indicate a very weak decollement layer, geometrically similar to the Mediterranean Ridge accretionary complex. Locally steep slopes (up to 10°) indicate strongly focused, active deformation and potential gravitational instabilities. The unusual surface morphology of the upper accretionary wedge includes “raft-tectonics” type fissures and abundant sub-circular depressions. Dissolution and/or diapiric processes are proposed to be involved in the formation of these depressions.
ISSN: 0264-8172

insu-00401683
https://hal-insu.archives-ouvertes.fr/insu-00401683
DOI : 10.1016/j.marpetgeo.2007.11.008

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We review the geodynamic evolution of the Aegea-Anatolia region and discuss strain localisation there over geological times. From Late Eocene to Present, crustal deformation in the Aegean backarc has localised progressively during slab retreat. Extension started with the formation of the Rhodope Metamorphic Core Complex (Eocene) and migrated to the Cyclades and the northern Menderes massif (Oligocene and Miocene), accommodated by crustal-scale detachments and a first series of core complexes (MCCs). Extension then localised in Western Turkey, the Corinth Rift and the external Hellenic arc after Messinian times, while the North Anatolian Fault penetrated the Aegean Sea. Through time the direction and style of extension have not changed significantly except in terms of localisation. The contributions of progressive slab retreat and tearing, basal drag, extrusion tectonics and tectonic inheritance are discussed and we favour a model (1) where slab retreat is the main driving engine, (2) successive slab tearing episodes are the main causes of this stepwise strain localisation and (3) the inherited heterogeneity of the crust is a major factor for localising detachments. The continental crust has an inherited strong heterogeneity and crustal-scale contacts such as major thrust planes act as weak zones or as zones of contrast of resistance and viscosity that can localise later deformation. The dynamics of slabs at depth and the asthenospheric flow due to slab retreat also have influence strain localisation in the upper plate. Successive slab ruptures from the Middle Miocene to the Late Miocene have isolated a narrow stripe of lithosphere, still attached to the African lithosphere below Crete. The formation of the North Anatolian Fault is partly a consequence of this evolution. The extrusion of Anatolia and the Aegean extension are partly driven from below (asthenospheric flow) and from above (extrusion of a lid of rigid crust).
ISSN: 0040-1951

insu-00715950
https://hal-insu.archives-ouvertes.fr/insu-00715950
https://hal-insu.archives-ouvertes.fr/insu-00715950/document
https://hal-insu.archives-ouvertes.fr/insu-00715950/file/Jolivet-Aegean_Tectonophysics-2012.pdf
DOI : 10.1016/j.tecto.2012.06.011

Éditeur(s) : Université Nice Sophia Antipolis
Résumé : The Lesser Antilles is a case study of a very slow subduction (~2 cm/yr) of an old oceanic lithosphere (~84-100 Ma). The region presents a relatively low seismic activity, especially along the interplate contact, and the seismic hazard associated with a possible mega-thrust earthquake is still poorly known. This PhD thesis is a first step toward assessing the ability of the Lesser Antilles subduction zone to produce such a large subduction event. To do so, it aims at constraining the downdip width of the interplate's seismogenic zone. The lack of coverage of permanent seismological stations is a major limitation in the exploration of the Lesser Antilles subduction zone. It is due to the presence of only small aligned islands at far distances from the potentially seismogenic interplate area. Several oceanographic cruises were therefore planned that notably allowed the repeated deployment of ocean bottom seismometers; some of them being left for a few months of background seismicity recording. This thesis specifically focuses on two sets of wide-angle seismic data acquired offshore the Dominica and Martinique islands. From their analysis 3D and 2D tomographic models were produced respectively over the forearc region and across the whole subduction complex. These models constrain the plates' seismic structure as well as their geometry. They allow the discussion of how the imaged structures affect the subduction processes and give a first estimation of the downdip width of the seimogenic zone, defined as the segment of the interplate between the backstop and the upper plate's Moho. The joint interpretation of seismic models and earthquake localizations then refine this first assessment. Epicenter distribution from height months of seismic recording shows indeed that seismicity concentrates within the inner forearc region. The strong velocity gradient that characterize its basement suggests it is denser and more rigid than the more deformable outer forearc basement. The updip limit of the seismogenic zone could then lie arcward of the backstop at the contact of the interplate and the seaward end of the inner forearc crust. At depth, interplate earthquake mechanisms are observed between 35 and 45 km depth and interpreted to have occurred at the downdip limit of the seismogenic zone. The latter could reach a depth over 10,km deeper than the contact of the upper plate's Moho with the interplate, and therefore lie within the mantle wedge. All together, these results imply a large downdip width of the seismogenic zone (~70 km) offshore the Dominica and Martinique islands. Further work is, however, needed in order to fully comprehend the ability of the Lesser Antilles subduction zone to produce a possible mega-thrust earthquake. This would necessitate the evaluation of seismic coupling at the interplate contact and the possible segmentation of the seismogenic zone, for instance, due to the subduction of oceanic ridges.
Les Petites Antilles présentent un contexte géodynamique caractérisé par la subduction à très faible vitesse (~2 cm/an) d'une lithosphère océanique âgée (~84-100 Ma). L'activité sismique y est relativement faible, notamment à l'interplaque, où l'aléa sismique lié à un éventuel séisme de méga-chevauchement reste encore mal contraint. Cette thèse se veut être une première étape dans l'évaluation de la capacité de la zone de subduction des Petites Antilles à générer un tel évènement. Dans ce but, ces travaux tentent d'appréhender l'extension en profondeur du domaine sismogène de l'interplaque. Le manque de couverture des stations sismologiques permanentes est un inconvénient majeur dans l'exploration des Petites Antilles. Il s'explique en raison du peu de terres émergées et de leur éloignement de la zone potentiellement sismogène de l’interplaque. La région a donc fait l'objet de plusieurs campagnes océanographiques qui ont permis, notamment, le déploiement de sismomètres fond de mer (OBS); certains instruments étant restés immergés plusieurs mois afin de procéder à une écoute de la sismicité. Les travaux réalisés au cours de cette thèse se sont focalisés sur deux jeux de données de sismique grand-angle acquis au large des îles de la Dominique et de la Martinique. Leur analyse a permis la construction de modèles tomographiques 3D et 2D respectivement à l'échelle de l'avant-arc et de l'ensemble de la subduction. Ces modèles renseignent sur la structure sismique des plaques en convergence ainsi que sur leur géométrie. Ils permettent de discuter le rôle de la structure dans le fonctionnement de la subduction et d’obtenir une première estimation de l'extension en profondeur de la zone sismogène en considérant la portion de l'interplaque comprise entre le butoir et le Moho de la plaque supérieure. Dans un second temps, l'interprétation conjointe des modèles tomographiques et des localisations des séismes locaux a permis d'affiner cette estimation. Huit mois d'enregistrement de la sismicité montrent en effet une concentration des épicentres dans la région interne de l’avant-arc. Celle-ci présente un socle épais, à fort gradient de vitesse interprété comme plus dense et rigide que le socle de la région externe de l'avant-arc, plus déformable. La limite amont de la zone sismogène pourrait donc se situer en retrait de la position du butoir au contact de l'interplaque et de la limite entre ces deux zones de l'avant-arc. En profondeur, des mécanismes interplaques sont observés entre 35 et 45 km et interprétés comme des marqueurs de la limite aval de la zone sismogène. Cette dernière pourrait donc atteindre une profondeur jusqu'à 10 km supérieure à la limite précédemment évoquée et se trouver, par conséquent, au contact du manteau lithosphérique. L'ensemble de ces résultats suggèrent une extension en profondeur de la zone sismogène (i.e une largeur) de près de 70 km face aux îles de la Dominique et de la Martinique. Ces travaux doivent cependant être poursuivis afin d’évaluer pleinement la capacité de la zone de subduction des Petites Antilles à générer un éventuel séisme de méga-chevauchement. Le taux de couplage à l'interplaque doit être précisé ainsi que sa possible segmentation en lien, par exemple, avec à l'entrée en subduction des rides océaniques.

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00172/28335/26628.pdf
http://archimer.ifremer.fr/doc/00172/28335/

Éditeur(s) : HAL CCSD IOS Press
Résumé : International audience
Because of the metabolic changes induced by a physical activity, the hemorheological properties of patients with sickle cell anemia could be further impaired and increase the risks for vaso-occlusive complications. However, few studies suggest that moderate physical activity could be beneficial rather than harmful in patients with sickle cell anemia (SCA). However, the definition of what can be considered as a moderate physical activity in SCA patients is imprecise. The present study tested the effects of a short incremental cycling exercise test conducted until the first ventilatory threshold on different biomarkers. Hematological and hemorheological parameters were compared between 8 patients with SCA and 13 healthy subjects (CONT) before, immediately after the end of the exercise and at 12, 36 and 60 hours after the exercise. We observed no significant hematological or hemorheological alteration induced by the exercise in the two groups. However, the exercise resulted in a delayed improvement of the red blood cell disaggregation threshold at 36 and 60 hrs after exercise in the SCA group which was paralleled to the decrease in the platelet count in this group. The present study suggests that such an exercise might be beneficial for microcirculatory blood flow.
ISSN: 1386-0291

hal-01137567
https://hal.univ-antilles.fr/hal-01137567

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Dien Bien Phu (DBP) Fault strikes nearly perpendicular to the general tectonic framework, separating northwest Vietnam into two compartments. The DBP and Muong Lay granites are exposed respectively east and west of the fault. The U/Pb age of 277 ± 2 Ma obtained for the Muong Lay granite is similar to the age of the Chieng Khuong complex exposed within the Song Ma structure east of the DBP Fault. These two magmatic intrusions are considered as belonging to a same tectonic structure related to the subduction of the Song Ma Ocean under the Indochina Block during the Indosinian orogeny. The DBP Fault with a total post Permian dextral offset of 30-40 km shifts the Song Ma Suture. It could then be connected to the Ailao Shan-Shuanggou suture to the north. The undeformed DBP granite gave a U/Pb age of 230 ± 1 Ma sealing the Indosinian deformation on the fault. The Ladinian-Carnian activity of the fault is confirmed by the 40Ar/39Ar (biotite) age of 228 ± 4 Ma obtained from the paragneiss forming the fault zone. A geodynamic model is proposed to describe the various tectonic phases recorded by on the DBP Fault. It associates field data, stratigraphic observations, and geochronology analyses (U/Pb, Ar/Ar, fission tracks). Following the Late Triassic exhumation of the granite and the end of the Indosinian orogeny marked by the Norian unconformity, the granite was buried under Jurassic and Lower Cretaceous sediments. A strong cooling event during the early Late Cretaceous (100 Ma) is associated with the reactivation of the DBP Fault and the accommodation of a southward thrusting of the Song Da terrane onto the Truong Son Belt. This newly recognised tectonic phase could be associated to the subduction of the Paleo-Pacific plate under the Indochina Block. No data are available yet to constrain the Tertiary evolution of the DBP system. However, the Tertiary deformation is likely similar to the Cretaceous one.
ISSN: 1342-937X

insu-01015379
https://hal-insu.archives-ouvertes.fr/insu-01015379
DOI : 10.1016/j.gr.2013.07.018

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
[1] This article presents (U-Th)/He thermochronological data from the Longmen Shan belt, eastern Tibet. Located between the Songpan-Garze terrane and the Yangtze craton, this mountain range is one of the steepest margins of the Tibetan Plateau and an important area for the comprehension of the mechanisms that control the dynamics of such plateau borders in terms of spatial distribution of deformation or timing of topographic building. We describe several age-elevation transects and perform forward modeling of our data to derive quantitative information on the exhumation of the range. A major phase of exhumation started at 8–11 Ma, with an average rate of $0.65 mm a À1. Comparison of zircon and apatite ages indicates that the eastern part of the range may have experienced a significant decrease in exhumation since 2–3 Ma. We use the distribution of finite exhumation across the major faults of the area to quantify their dip-slip throw rate over the last 10 Ma. The Beichuan Fault, which was activated during the 2008 Sichuan earthquake, is the major active structure of the Longmen Shan since the late Miocene, with an average thrusting slip rate between 0.4 and 1 mm a À1. Conversely, over the same time period, only minor dip-slip activity occurred on the Wenchuan Fault Zone. This distribution in space and time of exhumation and deformation is discussed and compared to the different proposed models for the geodynamical evolution of the eastern Tibetan margin. It also provides an important long-term perspective to put in context the destructive 2008 Sichuan earthquake that struck the central Longmen Shan.
ISSN: 0278-7407

hal-01577059
https://hal-amu.archives-ouvertes.fr/hal-01577059
https://hal-amu.archives-ouvertes.fr/hal-01577059/document
https://hal-amu.archives-ouvertes.fr/hal-01577059/file/godard2009late.pdf
DOI : 10.1029/2008TC002407