Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
TEM Study of Heavitree quartzite deformed at high temperatures and a pressure of 1.5 GPa with three different preparations: water-added, vacuum dried, and sodium doped show a wide range of dislocation microstructure. The vacuum dried sample has a very heterogeneous dislocation distribution varying from almost no dislocations to very high densities. Dislocation nucleation occurs by cross-slip mechanisms, such as Frank-Read sources and Orowan loops around hard inclusions. Shear bands develop in the basal plane composed of two closely spaced shear planes. Dislocations have straight segments and they are aligned along directions of dense packing, suggesting strong Peierls stress control due to the crystal structure. No voids, bubbles or dislocation walls where observed in the vacuum dried sample. The sodium-doped sample had a homogeneous high dislocation density. The water-added sample has a significantly lower, relatively uniform dislocation density. Bubbles associated with dislocations are seen in every grain. Dislocations were either present in loops around bubbles or as straight dislocations with small bubbles spaced along the dislocation line. Some of the long straight dislocations are aligned parallel to the c-axis. Sub-grains where very frequent, sometimes form cells of about 2 p,m in diameter with straight edges. Analysis of dislocations show 1/3 < a > and [c] dislocations in sub-grain walls and free 1/3 < a > dislocations on prism planes. There is clear evidence for dislocation climb with sub-grain walls, dislocation cells, dislocation junctions and dislocation debris of small loops. The major difference between vacuum dried and water-added samples are the homogeneity of the microstructure and evidence for climb in the water-added sample. Glide is clearly difficult, with a high Peierls stress in the vacuum dried sample as shown by areas of very low and very high dislocation density and the crystallographic control of dislocation line direction. The sodium-doped sample indicates that nucleation was easy by the high homogenous dislocation density, but no climb recovery has taken place. The density is high and the dislocations are strongly interacting causing tangles; no evidence for crystallographic control can be observed at these levels of strain. The activation energy for creep in Heavitree quartzite decreases with inferred water content of the specimens form 185 kJ mol(-1) for vacuum dried to 151 for 0.4 wt% water-added samples. Analysis of diffusion data for oxygen under hydrothermal conditions and inferred diffusion data for the hydrogarnet defect and dislocation velocity suggests activation energies for these processes are similar to the activation energy for the dislocation creep of Heavitree quartzite and other quartz aggregates. For data from the previously published experiments with the highest stress resolution there is a correlation between the A pre-factor in the power law creep equation and the activation energy for creep. It is speculated that the correlation may be due to variable hydrogarnet defect concentrations.
ISSN: 0031-9201

hal-00413112
https://hal.archives-ouvertes.fr/hal-00413112
DOI : 10.1016/j.pepi.2008.07.009

Éditeur(s) : HAL CCSD Springer
Résumé : International audience
Thermoelastic behavior of different marble types was analyzed using computational modeling and experimental measurements. Eight marble samples with different composition, grain size, grain boundary geometry, and texture were investigated. Calcitic and dolomitic marbles were considered. The average grain size varies from 75 μm to 1.75 mm; grain boundary geometry differs from nearly equigranular straight grain boundaries to inequigranular-interlobate grain boundaries. Four typical marble texture types were observed by EBSD measurements: weak texture; strong texture; girdle texture and high-temperature texture. These crystallographic orientations were used in conjunction with microstructure-based finite element analysis to compute the thermoelastic responses of marble upon heating. Microstructural response maps highlight regions and conditions in the marble fabric that are susceptible to degradation phenomena. This behavior was compared to the measured thermal expansion behavior, which shows increasing residual strains upon repetitive heating-cooling cycles. The thermal expansion behavior as a function of temperature changes can be classified into four categories: (a) isotropic thermal expansion with small or no residual strain; (b) anisotropic thermal expansion with small or no residual strain; (c) isotropic thermal expansion with a residual strain; and (d) anisotropic thermal expansion with residual strain. Thermal expansion coefficients were calculated for both simulated and experimental data and also modeled from the texture using the MTEX software. Fabric parameters control the amount and directional dependence of the thermal expansion. Marbles with strong texture show higher directional dependence of the thermal expansion coefficients and have smaller microstructural values of the maximum principal stress and strain energy density, the main precursors of microcracking throughout the marble fabric. In contrast, marbles with weak texture show isotropic thermal expansion behavior, have a higher propensity to microcracking, and exhibit higher values of maximum principal stress and strain energy density. Good agreement between the experimental and computational results is observed, demonstrating that microstructure-based finite-element simulations are an excellent tool for elucidating influences of rock fabric on thermoelastic behavior.
ISSN: 1866-6280

hal-00858095
https://hal.archives-ouvertes.fr/hal-00858095
DOI : 10.1007/s12665-013-2406-z

Éditeur(s) : HAL CCSD Elsevier
Résumé : Displacement-length data from faults, joints, veins, igneous dikes, shear deformation bands, and compaction bands define two groups. The first group, having a power-law scaling relation with a slope of n = 1 and therefore a linear dependence of maximum displacement and discontinuity length (D-max = gamma L), comprises faults and shear (non-compactional or non-dilational) deformation bands. These shearing-mode structures, having shearing strains that predominate over volumetric strains across them, grow under conditions of constant driving stress, with the magnitude of near-tip stress on the same order as the rock's yield strength in shear. The second group, having a power-law scaling relation with a slope of n = 0.5 and therefore a dependence of maximum displacement on the square root of discontinuity length (D-max = alpha L-0.5), comprises joints, veins, igneous dikes, cataclastic deformation bands, and compaction bands. These opening- and closing-mode structures grow under conditions of constant fracture toughness, implying significant amplification of near-tip stress within a zone of small-scale yielding at the discontinuity tip. Volumetric changes accommodated by grain fragmentation, and thus control of propagation by the rock's fracture toughness, are associated with scaling of predominantly dilational and compactional structures with an exponent of n = 0.5.
ISSN: 0191-8141

hal-00411173
https://hal.archives-ouvertes.fr/hal-00411173
DOI : 10.1016/j.jsg.2008.08.001