Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : Approximately 4 yr of campaign and continuous Global Positioning System (GPS) measurements across the Dead Sea fault system (DSFS) in Lebanon provide direct measurements of interseismic strain accumulation along a 200-km-long restraining bend in this continental transform fault. Late Cenozoic transpression within this restraining bend has maintained more than 3000 m of topography in the Mount Lebanon and Anti-Lebanon ranges. The GPS velocity field indicates 4-5 mm yr(-1) of relative plate motion is transferred through the restraining bend to the northern continuation of the DSFS in northwestern Syria. Near-field GPS velocities are generally parallel to the major, left-lateral strike-slip faults, suggesting that much of the expected convergence across the restraining bend is likely accommodated by different structures beyond the aperture of the GPS network (e.g. offshore Lebanon and, possibly, the Palmyride fold belt in SW Syria). Hence, these geodetic results suggest a partitioning of crustal deformation involving strike-slip displacements in the interior of the restraining bend, and crustal shortening in the outer part of the restraining bend. Within the uncertainties, the GPS-based rates of fault slip compare well with Holocene-averaged estimates of slip along the two principal strike-slip faults: the Yammouneh and Serghaya faults. Of these two faults, more slip occurs on the Yammouneh fault, which constitutes the primary plate boundary structure between the Arabia and Sinai plates. Hence, the Yammouneh fault is the structural linkage that transfers slip to the northern part of the transform in northwestern Syria. From the perspective of the regional earthquake hazard, the Yammouneh fault is presently locked and accumulating interseismic strain.
ISSN: 0956-540X

hal-00406620
https://hal.archives-ouvertes.fr/hal-00406620
DOI : 10.1111/j.1365-246X.2006.03328.x

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Lithospheric-scale faults related to oblique subduction are responsible for some of the most hazardous earthquakes reported worldwide. The mega-thrust in the Sunda sector of the Sumatran oblique subduction has been intensively studied, especially after the infamous 2004 Mw 9.1 earthquake, but its onshore kinematic complement within the Sumatran subduction, the transform Sumatran Fault System, has received considerably less attention. In this paper, we apply a combination of analysis of Digital Elevation Models (ASTER GDEM) and field evidence to resolve the kinematics of the leading edge of deformation of the northern sector of the Sumatran Fault System. To this end, we mapped the northernmost tip of Sumatra, including the islands to the northwest, between 4.5°N and 6°N. Here, major topographic highs are related to different faults. Using field evidence and our GDEM structural mapping, we can show that in the area where the fault bifurcates into two fault strands, two independent kinematic regimes evolve, both consistent with the large-scale framework of the Sumatran Fault System. Whereas the eastern branch is a classic Riedel system, the western branch features a fold-and-thrust belt. The latter contractional feature accommodated significant amounts (c. 20%) of shortening of the system in the study area. Our field observations of the tip of the NSFS match a strain pattern with a western contractional domain (Pulau Weh thrust splay) and an eastern extensional domain (Pulau Aceh Riedel system), which are together characteristic of the tip of a propagating strike-slip fault, from a mechanical viewpoint. For the first time, we describe the strain partitioning resulting from the propagation of the NSFS in Sumatra mainland. Our study helps understanding complex kinematics of an evolving strike-slip system, and stresses the importance of field studies in addition to remote sensing and geophysical studies.
ISSN: 0040-1951

hal-01467196
https://hal.archives-ouvertes.fr/hal-01467196
DOI : 10.1016/j.tecto.2016.04.050

Éditeur(s) : HAL CCSD
Résumé : In SW Yukon – SE Alaska, the boundary between the Pacific and North America plates is characterized by a syntaxis at the transition between the Aleutian subduction to the W and the Fairweather – Queen Charlotte strike-slip faults to the SE. The relative motion is oblique to the main fault structures, and the area is marked by the Yakutat block collision. From the Chugach – Saint Elias mountains in the plate boundary zone (up to 6 000 m high) to the intraplate strike-slip faults, markers of the present-day deformation give information on its partition in the system.During my PhD, I first measure surface deformation using a dense GPS network, deployed up to 500 km inland the North America plate. After precise processing and corrections of transient effects in the area (postseismic and glacial isostatic rebound), a new residual velocity field is produced for the syntaxis area, from which I derive strain rates. Those data allow me to quantify the fault slip rates for Fairweather and southern Denali strike-slip faults, and to characterize a bi-modal deformation pattern: Along the plate boundary, the deformation is localized on large-scale structures (accretionary prism to the W, Fairweather to the E); In the syntaxis area, strain rates are the highest and the GPS data shows a diffuse intraplate deformation, similar to an indentor pattern. The Yakutat block seems to strongly drive the North America plate deformation.This indentor pattern induces strong lateral variations on the large intraplate faults: the Denali – Totschunda – Duke River system. In a second part, I realize a regional geomorphological study to characterize the role and slip rate of those faults. From very high-resolution Digital Elevation Models (~ 1 m), a detailed cartography is done. On the basis of fieldwork observations, I measure offsets of fluvial and glacial markers, which are sampled for dating. A dextral cumulative deformation is highlighted on the northern Denali Fault, where as all southern Denali is marked by vertical deformation. This study allows me to quantify new slip rates for the system Denali – Totschunda – Duke River, and to show the leading role of the Totschunda (~ 14 mm/a) and Duke River (~ 6 mm/a) faults, contrary to the Denali Fault (~ 1 mm/a) North of the syntaxis.The new tectonic model for the Yakutat collision provides an important case study for the understanding of indentor systems. The concomitance of a rigid-block deformation (to the West) and diffuse deformation (to the East), as well as the near-zero slip rate on the lithospheric-scale southern Denali Fault highlight the major control of boundary conditions and the structural heritage on the orogen deformation.
Au SO Yukon – SE Alaska, la frontière entre les plaques Pacifique et Nord-Amérique est marquée par une syntaxe à la transition entre la subduction des Aléoutiennes à l’O et le décrochement de Fairweather – Queen Charlotte au SE. Le mouvement relatif est oblique et la région est marquée par la collision du bloc Yakutat. De la chaine des Chugach – Saint Elias en frontière de plaque (jusqu’à 6 000 m d’altitude) aux grands décrochements intraplaque, les marqueurs de la déformation actuelle apportent des informations sur sa partition dans ce système.Au cours de cette thèse, je m’intéresse dans un premier temps à mesurer la déformation de surface à l’aide d’un réseau GPS dense, déployé jusqu’à 500 km à l’intérieur de la plaque Nord-Amérique. Après un travail minutieux de traitement des données et de correction des effets transitoires (rebond post-glaciaire et post-sismique), un champ de vitesses résiduelles robuste et inédit est produit au niveau de la syntaxe, dont je dérive des taux de déformation. Ces données me permettent de quantifier les vitesses de glissement les failles décrochantes de Fairweather et Denali au Sud, et également de caractériser une déformation bimodale : En frontière de plaques, la déformation est localisée sur les grandes structures (prisme d’accrétion à l’O, Fairweather à l’E) ; Au niveau de la syntaxe, les taux de déformation sont les plus importants et les données GPS mettent en évidence une déformation intraplaque diffuse, similaire à un champ attendu à l’aplomb d’un indenteur. Le bloc Yakutat semble donc contrôler fortement la déformation de la plaque Nord-Amérique.Ce champ de déformation induit des variations latérales fortes sur les grandes failles intraplaque : le système Denali-Totschunda-Duke River. Dans une seconde partie, je réalise une étude géomorphologique régionale pour caractériser le rôle et la vitesse de ces failles. À partir de Modèles Numériques de Terrain très haute résolution (~ 1 m), une cartographie de détail est réalisée. Puis une mission de terrain me permet de mesurer des décalages sur des marqueurs fluviatiles et glaciaires et collecter des échantillons pour les dater. Je mets en évidence une déformation cumulée dextre sur le segment Nord de la faille de Denali, alors que toute la partie Sud déforme verticalement la surface. Cette étude me permet de quantifier de nouvelles vitesses de failles sur le système Denali-Totschunda-Duke River, et de montrer le rôle prépondérant des failles de Totschunda (~ 14 mm/a) et Duke River (~ 6 mm/a) contrairement à la faille de Denali (~ 1 mm/a) au Nord de la syntaxe.Le nouveau modèle cinématique proposé pour la région de collision Yakutat permet d’apporter un nouvel exemple à la compréhension des systèmes d’indenteur. La concomitance d’une déformation de blocs (à l’Ouest) et diffuse (à l’Est), ainsi que l’absence de déformation sur la faille lithosphérique de Denali Sud met en évidence le contrôle majeur des conditions aux limites et de l’héritage structural dans la déformation des orogènes.
https://hal.archives-ouvertes.fr/tel-01241688

tel-01241688
https://hal.archives-ouvertes.fr/tel-01241688
https://hal.archives-ouvertes.fr/tel-01241688/document
https://hal.archives-ouvertes.fr/tel-01241688/file/manuscrit_anais_v2_optimise.pdf

Éditeur(s) : HAL CCSD Wiley-Blackwell
Résumé : International audience
Physical modeling of oblique subduction is performed to study the mechanism of strain partitioning. The model is two-layer and includes the elasto-plastic lithosphere (the overriding and subducting plates) and the low-viscosity liquid asthenosphere. The subduction is driven by a push force from a piston and a pull force when the density contrast Ap between the subducting plate and the asthenosphere is positive. We vary both Ap and the interplate friction (frictional stresses). Slip partitioning is obtained only in the models with high interplate friction and only when the overriding plate contains a weak zone. This zone in the models corresponds either to locally thinned litho-sphere or to cut (fault). The horizontal, trench-normal component of the interplate friction force [Ffh[ can be comparable with the absolute value of the horizontal component of the nonhydrostatic interplate pressure force [Fph [ in the subduction zone. Ffh is always negative (compression), while Fph can be either negative (compressional subduction regime) or positive (extensional regime). High friction, which promotes partitioning, can completely cancel the extensional (suction) force Fph. Back arc tension and strike-slip faulting appear thus as conflicting processes, although they can coexist in the same subduction zone, depending on the relative values of relevant forces. It appears that high friction can exist only in compressional subduction zones where partitioning should develop more easily. This conclusion is supported by the comparison of two oblique subduction zones, having similar geometry: the compressional southern Kurile zone (strong partitioning) and extensional southern Ryukyu zone (no lithospheric-scale partitioning). Other factors controlling the strain partitioning are the length of the oblique subductlon zone, the boundary conditions at the transverse limits of the forearc sliver, and of course, the obliquity of subduction.
ISSN: 2169-9275

hal-01261396
https://hal.archives-ouvertes.fr/hal-01261396
https://hal.archives-ouvertes.fr/hal-01261396/document
https://hal.archives-ouvertes.fr/hal-01261396/file/chemendaJGR2000.pdf
DOI : 10.1029/1999JB900332

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
Detailed seafloor mapping in the area east of Taiwan revealed trench-parallel stretching and folding of the Ryukyu forearc and lateral motion of the accretionary wedge under oblique convergence. East of 122ø40'E, a steep accretionary wedge is elongated in an E-W direction. A major transcurrent right-lateral strike-slip fault accommodates the strain partitioning caused by an oblique convergence of 40 ø. A spectacular out-of-sequence thrust may be related to the subduction of a structural high lying in the axis of the N-S trending Gagua Ridge. This asperity is likely responsible for the uplift of the accretionary wedge and forearc basement and may have augmented strain partitioning by increasing the coupling between the two plates. West of 122ø40'E, the low-taper accretionary wedge is sheared in a direction subparallel to the convergence vector with respect to the Ryukyu Arc. The bayonet shape of the southern Ryukyu Arc slope partly results from the recent (re)opening of the southern Okinawa Trough at a rate of about 2 to 4 cm/yr. Right-lateral shearing of the sedimentary forearc with respect to the nonlinear Ryukyu backstop generates trench-parallel extension in the forearc sediment sequence at dilational jogs and trench-parallel folding at compressive jogs. The Hoping Basin lies above a diffuse trench/trench/fault (TTF) or TFF unstable triple junction moving toward the south along a N-S transform zone which accommodates the southward drift of the Ryukyu Arc with respect to Eurasia.
ISSN: 0278-7407

hal-01261555
https://hal.archives-ouvertes.fr/hal-01261555
https://hal.archives-ouvertes.fr/hal-01261555/document
https://hal.archives-ouvertes.fr/hal-01261555/file/Lallemand_et_al-1999-Tectonics.pdf
DOI : 10.1029/1998TC900011

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
New high-resolution marine data acquired aboard R/V Le Suroît was used to map active normal faults offshore Montserrat in greater detail. The main faults of the Montserrat-Havers fault zone have cumulative scarps up to 200 m high, and offset sedimentary layers by hundreds of meters. They are arranged in a right-stepping, en echelon, trans-tensional array, which confirms that they accommodate the left-lateral component of motion resulting from slip partitioning of oblique convergence along the volcanic arc. They cut across Montserrat's recent volcanic complex. Faulting and fissuring exerted control on the position of andesitic domes, which are aligned along the N110°E average fault trend. The ≈10 km-long fault segments that cross the island could produce damaging, M ≈ 6 events comparable to the shallow, 16 March 1985, Mw∼6.3 earthquake that ruptured a submarine, N140°E striking, left-lateral fault near Redonda.
ISSN: 0094-8276

insu-01586768
https://hal-insu.archives-ouvertes.fr/insu-01586768
https://hal-insu.archives-ouvertes.fr/insu-01586768/document
https://hal-insu.archives-ouvertes.fr/insu-01586768/file/Feuillet_et_al-2010-Geophysical_Research_Letters.pdf
DOI : 10.1029/2010GL042556

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This paper aims to present an overview on the influence of rheological heterogeneity and mechanical anisotropy on the deformation of continents. After briefly recapping the concept of rheological stratification of the lithosphere, we discuss two specific issues: (1) as supported by a growing body of geophysical and geological observations, crust=mantle mechanical coupling is usually efficient, especially beneath major transcurrent faults which probably crosscut the lithosphere and root within the sublithospheric mantle; and (2) in most geodynamic environments, mechanical properties of the mantle govern the tectonic behaviour of the lithosphere. Lateral rheological heterogeneity of the continental lithosphere may result from various sources, with variations in geothermal gradient being the principal one. The oldest domains of continents, the cratonic nuclei, are characterized by a relatively cold, thick, and consequently stiff lithosphere. On the other hand, rifting may also modify the thermal structure of the lithosphere. Depending on the relative stretching of the crust and upper mantle, a stiff or a weak heterogeneity may develop. Observations from rift domains suggest that rifting usually results in a larger thinning of the lithospheric mantle than of the crust, and therefore tends to generate a weak heterogeneity. Numerical models show that during continental collision, the presence of both stiff and weak rheological heterogeneities significantly influences the large-scale deformation of the continental lithosphere. They especially favour the development of lithospheric-scale strike-slip faults, which allow strain to be transferred between the heterogeneities. An heterogeneous strain partition occurs: cratons largely escape deformation, and strain tends to localize within or at the boundary of the rift basins provided compressional deformation starts before the thermal heterogeneity induced by rifting are compensated. Seismic and electrical conductivity anisotropies consistently point towards the existence of a coherent fabric in the lithospheric mantle beneath continental domains. Analysis of naturally deformed peridotites, experimental deformations and numerical simulations suggest that this fabric is developed during orogenic events and subsequently frozen in the lithospheric mantle. Because the mechanical properties of single-crystal olivine are anisotropic, i.e. dependent on the orientation of the applied forces relative to the dominant slip systems, a pervasive fabric frozen in the mantle may induce a significant mechanical anisotropy of the whole lithospheric mantle. It is suggested that this mechanical anisotropy is the source of the so-called tectonic inheritance, i.e. the systematic reactivation of ancient tectonic directions; it may especially explain preferential rift propagation and continental break-up along pre-existing orogenic belts. Thus, the deformation of continents during orogenic events results from a trade-off between tectonic forces applied at plate boundaries, plate geometry, and the intrinsic properties (rheological heterogeneity and mechanical anisotropy) of the continental plates.
ISSN: 0040-1951

hal-01389719
http://hal.univ-reunion.fr/hal-01389719
http://hal.univ-reunion.fr/hal-01389719/document
http://hal.univ-reunion.fr/hal-01389719/file/vauchez_etal_rheology_1998_hal.pdf
DOI : 10.1016/S0040-1951(98)00137-1