Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
The anisotropy of vibrational properties influences the acoustic behaviour of wooden pieces and their dependence on grain angle (GA). As most pieces of wood include some GA, either for technological reasons or due to grain deviations inside trunks, predicting its repercussions would be useful. This paper aims at evaluating the variability in the anisotropy of wood vibrational properties and analysing resulting trends as a function of orientation. GA dependence is described by a model based on transformation formulas applied to complex compliances, and literature data on anisotropic vibrational properties are reviewed. Ranges of variability, as well as representative sets of viscoelastic anisotropic parameters, are defined for mean hardwoods and softwoods and for contrasted wood types. GA-dependence calculations are in close agreement with published experimental results and allow comparing the sensitivity of different woods to GA. Calculated trends in damping coefficient (tanδ) and in specific modulus of elasticity (E′/ρ) allow reconstructing the general tanδ-E′/ρ statistical relationships previously reported. Trends for woods with different mechanical parameters merge into a single curve if anisotropic ratios (both elastic and of damping) are correlated between them, and with axial properties, as is indicated by the collected data. On the other hand, varying damping coefficient independently results in parallel curves, which coincide with observations on chemically modified woods, either "artificially", or by natural extractives.
ISSN: 0043-7719

hal-00804242
https://hal.archives-ouvertes.fr/hal-00804242
https://hal.archives-ouvertes.fr/hal-00804242/document
https://hal.archives-ouvertes.fr/hal-00804242/file/Anisotropy_wood_variational_properties_Bremaud_al_2011.pdf
DOI : 10.1007/s00226-010-0393-8

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
A feasibility study of glulam was carried out in French Guiana using local wood species. The aim was to determine gluing parameters affording satisfactory behaviour to manufactured glulam in a tropical climate. Three abundant wood species, with special properties, were selected for the study and Resorcinol-Phenol-Formaldehyde resin was used for bonding. Three industrial parameters were considered: adhesive spread rate, closed assembly time and gluing pressure. Delamination and shearing tests were carried outin accordance with European Standards. The tests revealed the influence of wood properties and manufacturing parameters on joint resistance. In fact, the results showed that specific gravity and the shrinkage coefficientgreatly influenced the gluing step. Indeed, wood with a medium specific gravity needed more adhesive and more pressure than wood with a high specific gravity. In addition, planning and lamella thicknesswere found to affect glue joint resistance.
ISSN: 0018-3768

hal-00856933
https://hal.archives-ouvertes.fr/hal-00856933
https://hal.archives-ouvertes.fr/hal-00856933/document
https://hal.archives-ouvertes.fr/hal-00856933/file/Feasibility_glued_laminated_timber_Bourreau_al.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Functional ecology has long considered the support function as important, but its biomechanical complexity is only just being elucidated. We show here that it can be described on the basis of four biomechanical traits, two safety traits against winds (SW) and self-buckling (SB), and two motricity traits involved in sustaining an upright position, tropic motion velocity (MV) and posture control (PC). All these traits are integrated at the tree scale, combining tree size and shape together with wood properties. The assumption of trait constancy has been used to derive allometric scaling laws, but it was more recently found that observing their variations among environments and functional groups, or during ontogeny, provides more insights into adaptive syndromes of tree shape and wood properties. However, over-simplified expressions have often been used, possibly concealing key adaptive drivers. An extreme case of over-simplification is the use of wood basic density as a proxy for safety. Actually, since wood density is involved in stiffness, loads and construction costs, the impact of its variations on safety is non-trivial. Moreover, other wood features, especially the microfibril angle (MFA), are also involved. Furthermore, wood is not only stiff and strong, but it also acts as a motor for MV and PC. The relevant wood trait for that is maturation strain asymmetry. Maturation strains vary with cell wall characteristics such as MFA, rather than with wood density. Finally, the need for further studies about the ecological relevance of branching patterns, motricity traits and growth responses to mechanical loads is discussed.
ISSN: 0022-0957

hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904
https://hal.archives-ouvertes.fr/hal-00909904/document
https://hal.archives-ouvertes.fr/hal-00909904/file/Integrative_biomechanics_for_tree_Fournier_al.pdf
DOI : 10.1093/jxb/ert279

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Studies on the periodicity of wood formation provide essential data on tree age and factors related to the control of tree growth. The aim of this work was to investigate the cambial phenology and its relation with leaf phenology and climatic seasonality in two tropical rainforest species belonging to the genus Parkia known for having a contrasted leaf phenology. From wood samples collected at 15 day intervals from April 2009 to February 2012 in five trees of both species, we quantified cambial activity by counting layers of cells in cambial zone, enlarging cells zone and wall thickening cells zone from wood prepared anatomical micro sections. In the same time, we observed leaf shedding behaviors in the crown of the studied trees. In both species, cambial activity was significantly reduced during leafless period. However, the cambial activity of P. velutina was not affected by seasonality while in P. nitida, we found a significant positive effect of the dry season on cambial activity. This diminution of activity associated to leaf shedding occurred annually during the dry season in P. nitida whereas the trees were not synchronous in time for P. velutina. On the contrary that is often admitted, the rest cambial period can be independent of environmental restriction such as dry season. Leaf phenology remains the best proxy to estimate cambial activity.
ISSN: 0931-1890

hal-01135166
https://hal.archives-ouvertes.fr/hal-01135166
https://hal.archives-ouvertes.fr/hal-01135166/document
https://hal.archives-ouvertes.fr/hal-01135166/file/Art_Morel_al_Seasonal_variations_phenological_traits_2015.pdf
DOI : 10.1007/s00468-015-1177-4

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Grain deviations and high extractives content are common features of many tropical woods. We aimed at clarifying their respective impact on vibrational properties, referring to African Padauk (Pterocarpus soyauxii Taub.), a species selected for its interlocked grain, high extractives content, and uses in xylophones. Specimens were cut parallel to the trunk axis (L), and local variations in grain angle (GA), microfibril angle (MFA), specific Young's modulus (E'L/ρ, where r stands for specific gravity) and damping coefficient (tanδL), were measured. GA dependence was analyzed by a mechanical model which allowed to identify the specific Young's modulus (E'3/ρ) and shear modulus (G'/ρ) along the grain (3), as well as their corresponding damping coefficients (tanδ3, tanδG). This analysis was done for native and then for extracted wood. Interlocked grain resulted in 0-25° GA and in variations of a factor 2 in E'L/ρ and tanδL. Along the grain, Padauk wood was characterized, as compared to typical hardwoods, by a somewhat lower E'3/ρ and elastic anisotropy (E'/G'), due to a wide microfibril angle plus a small weight effect of extracts; and a very low tanδ3 and moderate damping anisotropy (tanδG/tanδ3). Extraction affected mechanical parameters in the order: tanδ3 ≈ tanδG > G'/ρ >> E'3/ρ. That is, extractives' effects were nearly isotropic on damping but clearly anisotropic on storage moduli.
ISSN: 0043-7719

hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382
https://hal.archives-ouvertes.fr/hal-00544382/document
https://hal.archives-ouvertes.fr/hal-00544382/file/Identification_anisotropic_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0348-0

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Tension wood of Laetia procera (Poepp.) Eichl. (Flacourtiaceae), a neo-tropical forest species, shows a peculiar secondary wall structure, with an alternance of thick and thin layers, while opposite wood of this species has a typical secondary wall structure (S1 + S2 + S3). Samples for the study of microstructural properties were collected upon the estimation of growth stresses in the living tree, in order to analyze the correlation of the former with the latter. Investigation using optical microscopy, scanning electron microscopy and UV microspectrophotometry allowed the description of the anatomy, ultra-structure and chemistry of this peculiar polylaminate secondary wall. In the thick layers, cellulose microfibril angle is very low (i.e., microfibril orientation is close to fibre axis) and cellulose microfibrils are well organized and parallel to each other. In the thin layers, microfibrils (only observable in the inner layer) are less organized and are oriented with a large angle relative to the axis of the cell. Thick layers are lightly lignified although thin layers show a higher content of lignin, close to that of opposite wood secondary wall. The more the wood was under tensile stress, the less the secondary wall was lignified, and lower the syringyl on guaiacyl lignin units' ratio was. The innermost layer of the secondary wall looks like a typical S3 layer with large microfibril angle and lignin occurrence. The interest of this kind of structure for the understanding of stress generation is discussed.
ISSN: 0931-1890

hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923/document
https://hal.archives-ouvertes.fr/hal-00194923/file/Trees_RuelleYoshidaClairThibaut_submitted2006.pdf
DOI : 10.1007/s00468-007-0128-0

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Radial trends of vibrational properties, including the specific dynamic modulus (E'/r) and damping coefficient (tand), were investigated for 3 tropical rainforest hardwood species, Simarouba amara, Carapa procera and Symphonia globulifera by free-free flexural vibration test. The microfibril angle (MFA) was estimated through X-Ray diffraction. Consistent patterns of radial variations were observed for all studied properties. E'/r was found to decrease from pith to bark, which is strongly related to the increasing pith-bark trend of MFA. The variation of tand along the radius can be partly explained by MFA, and partly by the gradient of extractives due to heartwood formation. The coupling effect of MFA and extractives could be separated through the analysis of log(tand) - log(E'/r) diagram. For the studied species, the extractive content putatively associated to heartwood formation generally tends to decrease the wood damping coefficient. However, this weakening effect of extractives was not observed for inner part of the heartwood, suggesting the mechanical action of extractives was reduced during their chemical ageing.
ISSN: 1435-0211

hal-00797055
https://hal.archives-ouvertes.fr/hal-00797055
https://hal.archives-ouvertes.fr/hal-00797055/document
https://hal.archives-ouvertes.fr/hal-00797055/file/Radial_variations_vibrational_Zhang_al.pdf

Éditeur(s) : HAL CCSD
Résumé : For their survival, plants need to grow in height to access light resource while ensuring their mechanical stability. Growth in height amplifies the mechanical constraints due to wind and gravity. Nevertheless these constraints represent morphogenetic signals that plants respond to by modifying their growth. There are two regulatory processes of growth by mechanical signals: thigmomorphogenesis and gravitropism. Thigmomorphogenesis expresses by a reduction of growth in height and an increase of growth in girth under the effect of mechanical signals. This is a way for plants to grow with controlling slenderness of their axes to avoid buckling (beating down). In some cases (storm, sudden exposure to a new mechanical environment) this process is not sufficient to prevent buckling, gravitropism then acts to restore axes orientation in case of no lethal buckling. With measuring several traits, we have demonstrated that these processes have a fundamental ecological role in the control of tree habit and the vertical structuration of ecosystems. As studies of climate changes seem to predict a higher frequency of storms it is important to study the diversity of their efficiency.
Colloque Adaptation au Changement Climatique de l'Agriculture et des Ecosystèmes

hal-00797377
https://hal.archives-ouvertes.fr/hal-00797377

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Gravitropism is necessary for plants to control the orientation of their axes while they grow in height. In woody plants, stem re-orientations are costly because they are achieved through diameter growth. The functional diversity of gravitropism was studied to check if the mechanisms involved and their efficiency may contribute to the differentiation of height growth strategies between forest tree species at the seedling stage. Seedlings of eight tropical species were grown tilted in a greenhouse, and their up-righting movement and diameter growth were measured during three months. Morphological, anatomical and biomechanical traits were measured at the end of the survey. Curvature analysis was used to analyse the up-righting response along the stems. Variations in stem curvature depend on diameter growth, size effects, the increase in self-weight, and the efficiency of the gravitropic reaction. A biomechanical model was used to separate these contributions. Results showed that (1) gravitropic movements were based on a common mechanism associated to similar dynamic patterns, (2) clear differences in efficiency (defined as the change in curvature achieved during an elementary diameter increment for a given stem diameter) existed between species, (3) the equilibrium angle of the stem and the anatomical characters associated to the efficiency of the reaction also differed between species, (4) the differences in gravitropic reaction were related to the light requirements: heliophilic species, compared to more shade-tolerant species, had a larger efficiency and an equilibrium angle closer to vertical. This suggests that traits determining the gravitropic reaction are related to the strategy of light interception and may contribute to the differentiation of ecological strategies promoting the maintenance of biodiversity in tropical rain forests.
ISSN: 0022-0957

hal-00797023
https://hal.archives-ouvertes.fr/hal-00797023
https://hal.archives-ouvertes.fr/hal-00797023/document
https://hal.archives-ouvertes.fr/hal-00797023/file/Functional_diversity_gravitropic_Almeras_al.pdf

Éditeur(s) : HAL CCSD
COST E50 Workshop: Reaction wood formation at stand, tree and cellular level

hal-00797326
https://hal.archives-ouvertes.fr/hal-00797326

Éditeur(s) : HAL CCSD
Résumé : International audience
Some morphological and biochemical taxonomic markers are also affecting factors of dynamic mechanical properties of wood. Thus, could these properties reflect the classification/phylogeny of taxa? This work is a first insight into this question. It relied on the gathering (through experimental campaigns and exhaustive literature review) of a large database on the viscoelastic (i.e. including damping) vibrational properties of 445 woody species. relationship between damping was confirmed at a wide interspecific scale, but described no more than 40% of not in a way that could be easily related to the phylogenetic tree. Damping was a bit more -Papilionoideae and, to a lesser extent, Lauraceae, Cupressaceae and Moraceae) damping than average, independently While for some other families no clear characteristics could be observed at least with the present number of represented species. In the future, increasing the amount of data and compiling anatomical and chemical markers / affecting factors will allow further analysis at sub-family levels, and a better understanding of this wide topic.
6th Plant Biomechanics Conference PBM09
Cayenne, French Guiana

hal-00808398
https://hal.archives-ouvertes.fr/hal-00808398
https://hal.archives-ouvertes.fr/hal-00808398/document
https://hal.archives-ouvertes.fr/hal-00808398/file/Mechanical_damping_wood_Bremaud_al.pdf

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context and aim : This study aimed to examine the effect of the tension wood G‐layer on the viscoelastic properties of wood. Methods : Tension wood and opposite wood samples were obtained from six French Guianese tropical rainforest species (Sextonia rubra, Ocotea guyanensis, Inga alba, Tachigali melinoni, Iyranthera sagotiana and Virola michelii); the tension wood of the former three of these species had a Glayer, whilst the tension wood from the latter three had no Glayer. Tensile dynamic mechanical analysis (DMA) was performed on green never dried wood samples in the longitudinal direction with samples submerged in a water bath at a temperature (30°C) and frequency (1 Hz) representative of the conditions experienced by wood within a living tree. Then, DMA was repeated with samples conditioned to an air-dried state. Finally, samples were oven-dried to measure longitudinal shrinkage. Results : Tension wood did not always have a higher longitudinal storage (elastic) modulus than opposite wood from the same tree regardless of the presence or absence of a G‐layer. For the species containing a G‐layer, tension wood had a higher damping coefficient and experienced a greater longitudinal shrinkage upon drying than opposite wood from the same species. No difference was found in damping coefficients between tension wood and opposite wood for the species that had no G‐layer. Conclusion : It is proposed that the different molecular composition of the G-layer matrix has an influence on the viscoelasticity of wood, even if a biomechanical gain is not yet clear. This study shows that rheological properties and longitudinal shrinkage can be used to detect the presence of a G‐layer in tension wood.
ISSN: 1286-4560

hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460/document
https://hal.archives-ouvertes.fr/hal-00677460/file/Clair2.pdf
DOI : 10.1007/s13595-011-0164-1

Éditeur(s) : HAL CCSD
Résumé : Gravitropism is a major process in vertical growth as it allows the positioning of plant in the gravity field and thus, for trees, it takes part in the light foraging strategies. Without any gravitropism, trees would adopt a weeping habit or fall on the ground due to the increasing with growth supported weight, especially at the advance regeneration stage (sapling stage) in the understorey, where tree are very slender and poorly stiff. Most of the gravitropic studies are made by physiologists in order to understand the process and thus are associated to complex laboratory methods (genetic engineering, anatomical studies, accurate 2D ou 3D measurements of form changes with time). In order to study the ecological relevance and the specific diversity of gravitropic performances in natural forests, we developed a framework that uses different kinds of datas. Synchronical analysis has been done i) at the population level in large sample of trees and ii) at the tree level from destructive measurement of the dissymmetry maturation strains known to be the main motor of the posture control reaction of trees. In both cases, biomechanical models allows to estimate some aspects of the dynamic gravitropic process. Diachronical analysis has been done in natural conditions on permanent plots, or in a more traditional way, by observing in greenhouse experiments the righting movements of plants artificially tilted. In the first case, the problem is the high variability of natural disturbances and the slowness of growth and movements in the dark understorey. The second choice allows a measurement of a capacity (i.e. the ability of the species to react in quite extreme conditions of verticality disturbance but good for growth light and nutrient conditions) that is more easy to analyse, but is maybe not so relevant for estimating the ecological strategy (some species could have developed a high efficience of gravitropic reaction in natural conditions by avoiding the mechanical disturbance or adapting the reaction to slow growth and changing environments in natural conditions). All approaches use the same basic biomechanical modelling, i) to analyse simultaneously the reaction and the disturbance (due to the weight increase) during growth, or ii) to combine different parameters (geometry, growth, weight, maturation strains) involved in shape changes and posture control. They give a classification of the species according to their gravitropic performances. Results on 15 species are discussed, with relation to shade-tolerance or avoidance.
6th Plant Biomechanics Conference
Cayenne, France

hal-00565956
https://hal.archives-ouvertes.fr/hal-00565956

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Extractives can affect vibrational properties tanδ (damping coefficient) and E'/ρ (specific Young's modulus) but this is highly dependent on species, compounds, and cellular locations. This paper investigates such effects for African Padauk (Pterocarpus soyauxii Taub.), a tropical hardwood with high extractives content and a preferred material for xylophones. 5 groups of 26 heartwood specimens with large, yet comparable, ranges in vibrational properties were extracted in different solvents. Changes in vibrational properties were set against yields of extracts and evaluation of their cellular location. Methanol (ME) reached most of compounds (13%), located about half in lumen and half in cell-wall. Water solubility was extremely low. tanδ and E'/ρ were very strongly related (R2≥0.93), but native wood had abnormally low values of tanδ, while extraction shifted this relation towards higher tanδ values. ME extracted heartwood became in agreement with the average of many species, and close to sapwood. Extractions increased tanδ as much as 60%, irrespective of minute moisture changes or of initial properties. Apparent E'/ρ was barely changed (+2% to -4%) but, after correcting the mass contribution of extracts, was in fact slightly reduced (down to -10% for high E'/ρ), and increasingly so for specimens with low initial values of E'/ρ.
ISSN: 0043-7719

hal-00804236
https://hal.archives-ouvertes.fr/hal-00804236
https://hal.archives-ouvertes.fr/hal-00804236/document
https://hal.archives-ouvertes.fr/hal-00804236/file/Effect_extractives_vibrational_properties_Bremaud_al.pdf
DOI : 10.1007/s00226-010-0337-3

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
Reaction wood produces very peculiar maturation stresses at the tree periphery i.e. compressive stress or very high tensile stress, for compression and tension wood respectively, as compared to moderately high tensile stress for normal wood. This means that both its mechanical state and its mechanical and physical properties differ from normal wood. Compression wood shows big differences from normal wood in conifers, for all physical and mechanical properties: higher density and axial crushing strength (MOR) but lower modulus of elasticity (MOE), far higher axial (longitudinal) shrinkage but lower radial and tangential shrinkage, sometimes even lower than the axial shrinkage. For tension wood things are less simple and can vary a lot from hardwood species to species. Globally there are no systematic differences in density and transverse shrinkage, MOE tends to be a little higher while MOR is slightly lower. However, axial shrinkage is much higher for tension wood with a gelatinous layer (G layer) than normal wood due to the specific gel like organization of cellulose microfibrils in the G layer. For tension wood without a G layer(which is rather frequent) axial shrinkage in the first drying operation is around two times higher than in normal wood mainly because of a kind of hygro-thermal release of locked in maturation stress. Overall the very high tensile stress and stored elastic energy in tension wood lead to problemsin wood processing (end splitting and board warping), which is far less the case for compression wood. But due to the large difference in properties relative to normal wood, compression wood occurrence is always a big problem for the in service behaviour of timber, which is seldom the case for tension wood.
The biology of reaction wood

ISBN : 978-3-642-10813-6
hal-01135273
https://hal.archives-ouvertes.fr/hal-01135273

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
The vibration damping coefficient (tanδ) of wood is an important property for acoustical uses, including musical instruments. Current difficulties in the availability of some of the preferred species call for diversification, but this comes up against the lack of systematic damping coefficient data. * Keeping in mind the possible factors affecting tanδ, could we predict its variations between species, by using indicators that are either easily measured and/or readily available for many species? * Vibrational properties, equilibrium moisture content and colorimetric parameters were assessed on 94 wood types belonging to 76 species. Experimental results were then related to data on chemical contents and physical properties from the CIRAD database. The "standard" relationship between tanδ and specific modulus of elasticity (E'/ρ) explained only half of the variations. Deviations from this trend were correlated to extractives content, yet effects were not directly quantitative. Damping deviations were also correlated to colour and moisture-related properties, especially so with fibre saturation point. * By taking into account a combination of moisture-related properties, colour - or extractives content, and the "standard" relationship between tanδ and E'/ρ, we could propose simple predictive models which explain up to 89% of observed variations in tanδ between 48 species.
ISSN: 1286-4560

hal-00808338
https://hal.archives-ouvertes.fr/hal-00808338
https://hal.archives-ouvertes.fr/hal-00808338/document
https://hal.archives-ouvertes.fr/hal-00808338/file/Physico-chemical_indicators_Bremaud_al.pdf
DOI : 10.1051/forest/2010032

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Background : This study examines the radial trend in wood stiffness of tropical rainforest trees. The objective was to determine if the type of growing environment (exposed plantation or dense primary forest) would have an effect on this radial trend. Methods : The axial elastic modulus of wood samples, representing a pith to bark cross-section, of six trees from several French Guianese species (two of Eperua falcata, one of Eperua grandiflora, two of Carapa procera and one of Symphonia gloubulifera) was measured using a dynamic "forced vibration" method. Results : Primary forest trees were observed to have a decrease in wood stiffness from pith to bark, whereas plantation trees, from the same genus or species, displayed a corresponding increase in wood stiffness. Juvenile wood stiffness appears to vary depending on the environment in which the tree had grown. Conclusion : We suggest that the growth strategy of primary forest trees is to produce wood resistant to selfbuckling so that the height of the canopy may be obtained with the maximum of efficiency. In contrast, the growth strategy of the trees growing in an exposed plantation is to produce low-stiffness wood, important to provide flexibility in wind. Further experiments to study the behaviour of more species, with more individuals per species, growing across a range of physical environments, are required.
ISSN: 1286-4560

hal-00644335
https://hal.archives-ouvertes.fr/hal-00644335
https://hal.archives-ouvertes.fr/hal-00644335/document
https://hal.archives-ouvertes.fr/hal-00644335/file/McLean_al.pdf
DOI : 10.1007/s13595-011-0085-z