Éditeur(s) : HAL CCSD
Résumé :  
Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rain forest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood, and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-01032051
https://hal.archives-ouvertes.fr/hal-01032051

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé : International audience
Context and aim : This study aimed to examine the effect of the tension wood G‐layer on the viscoelastic properties of wood. Methods : Tension wood and opposite wood samples were obtained from six French Guianese tropical rainforest species (Sextonia rubra, Ocotea guyanensis, Inga alba, Tachigali melinoni, Iyranthera sagotiana and Virola michelii); the tension wood of the former three of these species had a Glayer, whilst the tension wood from the latter three had no Glayer. Tensile dynamic mechanical analysis (DMA) was performed on green never dried wood samples in the longitudinal direction with samples submerged in a water bath at a temperature (30°C) and frequency (1 Hz) representative of the conditions experienced by wood within a living tree. Then, DMA was repeated with samples conditioned to an air-dried state. Finally, samples were oven-dried to measure longitudinal shrinkage. Results : Tension wood did not always have a higher longitudinal storage (elastic) modulus than opposite wood from the same tree regardless of the presence or absence of a G‐layer. For the species containing a G‐layer, tension wood had a higher damping coefficient and experienced a greater longitudinal shrinkage upon drying than opposite wood from the same species. No difference was found in damping coefficients between tension wood and opposite wood for the species that had no G‐layer. Conclusion : It is proposed that the different molecular composition of the G-layer matrix has an influence on the viscoelasticity of wood, even if a biomechanical gain is not yet clear. This study shows that rheological properties and longitudinal shrinkage can be used to detect the presence of a G‐layer in tension wood.
ISSN: 1286-4560

hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460
https://hal.archives-ouvertes.fr/hal-00677460/document
https://hal.archives-ouvertes.fr/hal-00677460/file/Clair2.pdf
DOI : 10.1007/s13595-011-0164-1

Éditeur(s) : HAL CCSD
Résumé : International audience
The anatomy of tension wood and opposite wood was compared in 21 tropical rain forest trees from 21 species belonging to 18 families from French Guyana. Wood specimens were taken from the upper and lower sides of naturally tilted trees. Measurement of the growth stress level ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile-stressed wood on the upper side, called tension wood and normally tensile-stressed wood on the lower side, called opposite wood. Quantitative parameters relating to fibres and vessels were measured on transverse sections of both tension and opposite wood to check if certain criteria can easily discriminate the two kinds of wood. We observed a decrease in the frequency of vessels in the tension wood in all the trees studied. Other criteria concerning shape and surface area of the vessels, fibre diameter or cell wall thickness did not reveal any general trend. At the ultrastructural level, we observed that the microfibril angle in the tension wood sample was lower than in opposite wood in all the trees except one (Licania membranacea).
IAWA Journal

hal-00194915
https://hal.archives-ouvertes.fr/hal-00194915
https://hal.archives-ouvertes.fr/hal-00194915/document
https://hal.archives-ouvertes.fr/hal-00194915/file/IAWA2006_RuelleClairBeauchenePrevostFournier_ccsd.pdf
IRD : PAR00001321

Éditeur(s) : HAL CCSD
Résumé : International audience
Trees can control their shape and resist gravity thanks to their ability to produce wood under tensile stress. This stress is known to be produced during the maturation of wood fibres but the mechanism of its generation remains unclear. This study focuses on the formation of the secondary wall in tension wood produced in artificially tilted poplar saplings. Thickness of secondary wall layer (SL) and gelatinous layer (GL) were measured from cambium to mature wood in several trees sampled at different times after tilting. Measurements on wood fibres produced before tilting show the progressive increase of secondary wall thickness during the growing season. After the tilting date, SL thickness decreased markedly from normal wood to tension wood while the total thickness increased compared to normal wood, with the development of a thick GL. However, even after GL formation, SL thickness continues to increase during the growing season. GL thickening was observed to be faster than SL thickening. The development of the unlignified GL is proposed to be a low cost, efficient strategy for a fast generation of tensile stress in broadleaved trees.
IAWA journal / International Association of Wood Anatomists.

hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277/document
https://hal.archives-ouvertes.fr/hal-01229277/file/AbediniClair-Iawa-TensionCellWallThickening_preprint_HAL.pdf
DOI : 10.1163/22941932-00000084

Éditeur(s) : HAL CCSD Linnean Society of London
Résumé : International audience
The circumscription of Salicaceae has recently been enlarged to include a majority of the species formerly placed in the polyphyletic tropical family Flacourtiaceae. Several studies have reported a peculiar and infrequently formed multilayered structure of tension wood in four of the tropical genera. Tension wood is a tissue produced by trees to restore their vertical orientation, and most studies have focused on trees developing tension wood by means of cellulose-rich, gelatinous fibres, as is known in Populus L. and Salix L. (Salicaceae s.s.). This study aims to determine if the multilayered structure of tension wood is an anatomical characteristic common in other Salicaceae, and if so, how its distribution correlates to phylogenetic relationships. Therefore, we studied the tension wood of 14 genera of Salicaceae as well as two genera of Achariaceae, one genus of Goupiaceae, and one genus of Lacistemataceae, families closely related to Salicaceae or formerly placed in Flacourtiaceae. Opposite wood and tension wood were compared with light microscopy and 3D Laser Scanning Confocal Microscopy. The results indicate that a multilayered structure of tension wood is common in the family except in Salix, Populus, and one of their closest relatives, Idesia polycarpa Maxim. We suggest that tension wood may be a useful anatomical character in understanding phylogenetic relationships in Salicaceae. Further investigation is still needed on the tension wood of several other putatively close relatives of Salix and Populus, in particular Bennettiodendron Merr., Macrohasseltia L.O.Williams and Itoa Hemsl.
ISSN: 0024-4074

hal-01392845
https://hal.archives-ouvertes.fr/hal-01392845
https://hal.archives-ouvertes.fr/hal-01392845/document
https://hal.archives-ouvertes.fr/hal-01392845/file/GhislainEtAl2016_MultylayerTWSalicaceae_Bot_Jsur the_Lin_Soc_HALssfig.pdf
DOI : 10.1111/boj.12471

Éditeur(s) : HAL CCSD
Résumé : International audience
Tension wood, a tissue developed by angiosperm trees to actively recover their verticality, has long been defined by the presence of an unlignified cellulosic inner layer in the cell wall of fibres, called the G-layer. Although it was known that some species have no G-layer, the definition was appropriate since it enabled easy detection of tension wood zones using various staining techniques for either cellulose or lignin. For several years now, irrespective of its anatomical structure, tension wood has been defined by its high mechanical internal tensile stress. This definition enables screening of the diversity of cell walls in tension wood fibres. Recent results obtained in tropical species with tension wood with a delay in the lignification of the G-layer opened our eyes to the effective presence of large amounts of lignin in the G-layer of some species. This led us to review older literature mentioning the presence of lignin deposits in the G-layer and give them credit. Advances in the knowledge of tension wood fibres allow us to reconsider some previous classifications of the diversity in the organisation of the fibre walls of the tension wood.
ISSN: 0928-1541

hal-01636686
https://hal.archives-ouvertes.fr/hal-01636686
https://hal.archives-ouvertes.fr/hal-01636686/document
https://hal.archives-ouvertes.fr/hal-01636686/file/2017_Ghislain-Clair_IAWAJ_DiversityOrganisationLignificationTensionWoodFibreWalls-AReview.pdf
DOI : 10.1163/22941932-20170170

Éditeur(s) : HAL CCSD
Résumé :  
The anatomy of tension wood and opposite wood was compared in 21 tropical rain forest trees from 21 species belonging to 18 families from French Guyana. Wood secimens were taken from the upper and lower sides of naturally titled trees. Measurement of the growth stress level ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile-stressed wood on the upper side, called tension wood and normally tensile-stressed wood on the lower side, called opposite wood. Quantitative parameters relating to fibres and vessels were measured on transverse sections of both tension and opposite wood to check if certain criteria can easily discriminate the two kinds of wood. We observed a decrease in the frequency of vessels in the tension wood in all the trees studied. Other criteria concerning shape and surface area of the vessels, fibre diameter or cell wall thickness did not reveal any general trend.At the ultrastructural level, we observed that the microfibril angle in the tension wood sample was lower than in opposite wood in all the trees except one (Licania membranacea).
IAWA Journal

hal-01032149
https://hal.archives-ouvertes.fr/hal-01032149

Éditeur(s) : HAL CCSD Walter de Gruyter
Résumé :  
A method for measuring shrinkage resulting from drying in the three anisotropic directions is developed and tested. Measurements are performed on sawn discs, a technique which simplifies preparation and enables large numbers of measurements. Shrinkage values can be represented as a map of the disc surface. The results indicate that comparisons between shrinkage distribution and tension wood distribution on the discs show a clear relationship and can be measured with relatively high accuracy in reference to the "shrinkage map". In the long term, this method could be useful in the timber industry as a means for choosing the direction in which logs are cut depending on their type of wood composition.
Holzforschung

hal-01032055
https://hal.archives-ouvertes.fr/hal-01032055
DOI : 10.1515/HF.2003.100

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
Reaction wood produces very peculiar maturation stresses at the tree periphery i.e. compressive stress or very high tensile stress, for compression and tension wood respectively, as compared to moderately high tensile stress for normal wood. This means that both its mechanical state and its mechanical and physical properties differ from normal wood. Compression wood shows big differences from normal wood in conifers, for all physical and mechanical properties: higher density and axial crushing strength (MOR) but lower modulus of elasticity (MOE), far higher axial (longitudinal) shrinkage but lower radial and tangential shrinkage, sometimes even lower than the axial shrinkage. For tension wood things are less simple and can vary a lot from hardwood species to species. Globally there are no systematic differences in density and transverse shrinkage, MOE tends to be a little higher while MOR is slightly lower. However, axial shrinkage is much higher for tension wood with a gelatinous layer (G layer) than normal wood due to the specific gel like organization of cellulose microfibrils in the G layer. For tension wood without a G layer(which is rather frequent) axial shrinkage in the first drying operation is around two times higher than in normal wood mainly because of a kind of hygro-thermal release of locked in maturation stress. Overall the very high tensile stress and stored elastic energy in tension wood lead to problemsin wood processing (end splitting and board warping), which is far less the case for compression wood. But due to the large difference in properties relative to normal wood, compression wood occurrence is always a big problem for the in service behaviour of timber, which is seldom the case for tension wood.
The biology of reaction wood

ISBN : 978-3-642-10813-6
hal-01135273
https://hal.archives-ouvertes.fr/hal-01135273

Éditeur(s) : HAL CCSD
Résumé : International audience
A key element of the biomechanical design of trees is their ability to generate largemechanical stresses in wood at the stem periphery. This function is necessary for the tree tocontrol the orientation of its axes, and therefore to grow in height, maintain its branches at anoptimal angle or achieve adaptive reorientations (Fournier et al., 2013). This “maturationstress” appears in wood fibres during their cellular maturation when their secondary cell wallis thickening. In hardwoods, the stress asymmetry is generated by the formation of specificfibres with a very high tensile growth stress on the upper side of the inclined axis. Theresulting tension wood has microstructural features highly different from the normal wood.Tension wood in almost all temperate species has a specific gelatinous cell wall layer, calledG-layer, that is not lignified and highly mesoporous (Chang et al., 2015). It has been shownrecently, at the macroscopic scale, that cellulose tension appears during maturation and issynchronous with the development of this specific layer (Clair et al., 2011). Tropical species,like simarouba, are able to generate lignified tension wood fibres. The mechanisms of stressgeneration in tension wood fibres are not yet well known. The aim of our study is tounderstand these mechanisms and to know the spatial and temporal kinetics of the differentcell wall layers stiffening during maturation, in parallel with tensile stress generation.Contact-Resonance Atomic Force Microscopy, CR-AFM, was used here to address thisquestion on embedded samples (Arnould and Arinero, 2015) using dual resonance frequencytracking (DRFT, Rodriguez et al., 2007). Change in the contact modulus between, and within,each layer of the cell wall has been measured on several radial lines of developing fibres atdifferent steps. In order to understand the obtained results, and to estimate the sensitivity ofthe AFM indentation-like technique to the different cell wall components stiffness, an elasticanisotropic indentation model was used (Vlassak et al., 2003; Jäger et al., 2011). Finally,these mechanical measurements have been compared to topochemical data obtained on thesame fibres.
8th Plant Biomechanics International Conference
Nagoya, Japan

hal-01436113
https://hal.archives-ouvertes.fr/hal-01436113

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called G-layer, in the fibre wall. The structure of G-layer has been recently described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2 to 50 nm). This led us to revisit the concept of G-layer that was until now only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with typical thick G-layer while it is much less with thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without G-layer is as low as in normal wood. Not depending on the amount of pores, the pore sizes distribution are always centred around 6-12 nm. These results suggest that, among species producing fibres with G-layer, large structural differences of G-layer exist between species
ISSN: 0022-0957

hal-00387861
https://hal.archives-ouvertes.fr/hal-00387861
DOI : 10.1093/jxp/erp133

Éditeur(s) : HAL CCSD
Résumé : Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rainforest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of the G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-00112579
https://hal.archives-ouvertes.fr/hal-00112579
https://hal.archives-ouvertes.fr/hal-00112579/document
https://hal.archives-ouvertes.fr/hal-00112579/file/IAWA2006_ClairRuelleBeauchenePrevostFournier_ccsd.pdf
IRD : PAR00001136

Éditeur(s) : HAL CCSD Springer Verlag/EDP Sciences
Résumé :  
On 10 trees from 10 species of French Guyana tropical rainforest in a clear active process of restoring verticality growth strains were measured in situ in order to determine the occurrence of tension wood within samples. Wood specimens were cut in the vicinity of the growth strains measurements in order to measure some mechanical and physical properties. As suspected, tensile growth strains was very much higher in tension wood zone, because longitudinal modulus of elasticity was slightly higher. Longitudinal shrinkage was also much higher in tension wood than in opposite wood.
ISSN: 1286-4560

hal-01032110
https://hal.archives-ouvertes.fr/hal-01032110
DOI : 10.1051/forest:2007027

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Transverse drying shrinkage was measured at microscopic and mesoscopic levels in poplar wood characterised by an increasing growth strain (GS), from normal to tension wood. Results show that: (a) The drying shrinkage, measured as a relative thickness decrease, was significantly higher for G-layer (GL) than the other layers (OL), GL shrinkage was not significantly correlated with GS and OL shrinkage was negatively correlated with GS. (b) In gelatinous fibre (G-fibre), lumen size increased during drying and this increase was positively related with GS, but in normal wood fibre lumen size decreased during drying. These findings suggest that GL shrank outwards, so that its shrinkage feebly affected the total cell shrinkage and the mesoscopic shrinkage was controlled by the OL shrinkage which shrank inwards. (c) Measurements done on 7×7 mm² thin sections evidenced a negative correlation between transverse shrinkage and GS, significant in T direction but weak in R direction. These observations at both levels allow to discuss the contribution of GL to the mesoscopic shrinkage of tension wood.
ISSN: 0043-7719

hal-00194930
https://hal.archives-ouvertes.fr/hal-00194930
https://hal.archives-ouvertes.fr/hal-00194930/document
https://hal.archives-ouvertes.fr/hal-00194930/file/WST_FANG2006.pdf
DOI : 10.1007/s00226-007-0148-3

Éditeur(s) : HAL CCSD
Résumé : International audience
Over the past decade, much attention has been devoted to the development of forest biomass estimation methods at a stand scale, leading to the establishment of allometric models (Chave et al., 2014). These allometric equations use a unique wood specific gravity value (WSG) per species, but neglect the within tree variations of WSG found by others (Wiemann & Williamson, 1989).The main objectives of this study are (1) to illustrate the diversity of radial (from pith to bark) and longitudinal (from bottom to top) patterns of WSG variation within and between species, (2) to highlight different trends of WSG radial variations and the possible misinterpretations of these trends due to the effect of heartwood and (3) to link these variations and patterns to the successional status of the species (from pioneer to sciaphilic species).We sampled 33 small trees (10 Wood sciences underpinning tropical ecology and management. International closing symposium of the XYLAREDD project.
Tervuren, Belgium

hal-01188894
https://hal-sde.archives-ouvertes.fr/hal-01188894

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy B - Oxford Open Option B
Résumé : International audience
To recover verticality after disturbance, angiosperm trees produce " tension wood " allowing them to bend actively. The driving force of the tension has been shown to take place in the G-layer, a specific unlignified layer of the cell wall observed in most temperate species. However, in tropical rain forests, the G-layer is often absent and the mechanism generating the forces to reorient trees remains unclear. A study was carried out on tilted seedlings, saplings and adult Simarouba amara trees – a species known to not produce a G-layer. Microscopic observations were done on sections of normal and tension wood after staining or observed under UV light to assess the presence/absence of lignin. We showed that S. amara produces a cell-wall layer with all of the characteristics typical of G-layers, but that this G-layer can be observed only as a temporary stage of the cell-wall development because it is masked by a late lignification. Being thin and lignified, tension wood fibres cannot be distinguished from normal wood fibres in the mature wood of adult trees. These observations indicate that the mechanism generating the high tensile stress in tension wood is likely to be the same as that in species with a typical G-layer and also in species where the G-layer cannot be observed in mature cells.
ISSN: 0829-318X

hal-01229280
https://hal.archives-ouvertes.fr/hal-01229280
https://hal.archives-ouvertes.fr/hal-01229280/document
https://hal.archives-ouvertes.fr/hal-01229280/file/Roussel-Clair-2015-TreePhysiol-LateLignifGLayerSimarouba_preprintHAL.pdf
DOI : 10.1093/treephys/tpv082

Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy B - Oxford Open Option A
Résumé :  
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called the G-layer, in the fibre cell wall. The structure of the G-layer has recently been described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2-50 nm). This led us to revisit the concept of the G-layer that had been, until now, only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with a typical thick G-layer while it is much less with a thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without a G-layer is as low as in normal wood. Not depending on the amount of pores, the pore size distribution is always centred around 6-12 nm. These results suggest that, among species producing fibres with a G-layer, large structural differences of the G-layer exist between species.
Journal of Experimental Botany

hal-01032161
https://hal.archives-ouvertes.fr/hal-01032161
DOI : 10.1093/jxb/erp133

Éditeur(s) : HAL CCSD Springer Verlag
Résumé :  
Growth strains were measured in situ in nine trees of three species from a French Guiana tropical rainforest in a clearly active verticality restoration process. The aim was to detect tension wood within the samples. Wood specimens were cut in the vicinity of the growth strain measurements in order to determine the microfibril angle and some mechanical and physical properties. As suspected, tensile growth strain was much higher in tension wood zones, as shown by the slightly higher longitudinal modulus of elasticity. Conversely, tension wood showed reduced compression strength. Longitudinal shrinkage was much higher in tension wood than in opposite wood. Clear relationships between the microfibril angle and longitudinal properties were noted in comparison (i) with those observed in gymnosperm compression wood and (ii) with expected relationships from the organization of wood fibres cell wall structure.
ISSN: 0043-7719

hal-01032114
https://hal.archives-ouvertes.fr/hal-01032114
DOI : 10.1007/s00226-010-0323-9

Éditeur(s) : HAL CCSD North Carolina State University
Résumé : Few studies have been conducted about relation between cellulose parameters and biomechanical properties of wood in tropical angiosperms species. For this purpose, on 13 trees from 3 species of French Guyana tropical rainforest in a clear active process of restoring verticality, i) growth strains were measured in situ in order to determine the occurrence of tension wood within samples and ii) cellulose structural parameters were estimated on all the samples using X-ray diffraction method. Crystallite size was estimated from the full-width at half-maximum of the Miller index (002) arc diffraction and angle T was measured following Cave's method. Relationships between these parameters and growth stresses were good and the variations between normal and tension wood were significant, i.e. a lower angle T and a larger crystallite size in tension wood. In order to have a good estimation of the microfibril angle in the main layer of the secondary wall for each species, an experimental calibration was done between angle T and microfibril angle observed with scanning electron microscopy.
ISSN: 19302126

hal-01031799
https://hal.archives-ouvertes.fr/hal-01031799
https://hal.archives-ouvertes.fr/hal-01031799/document
https://hal.archives-ouvertes.fr/hal-01031799/file/42-575-1-PB.pdf