Résumé : This label was created on October 20th 1900. Around the turn of the 20th century, cigars were advertised and sold mainly by the colourful, intricate labels that adorned the boxes. Intense competition encouraged manufacturers to see who could create the most beautiful, eye-catching labels. A diffrent stone was required to print each colour. It was not unusual for as many as 20 stones to be used to create a single label. The register for each printing had to be perfect. The process became known as STONE LITHOGRAPHY or CHROMOLITHOGRAPHY. Once this exacting printing process was completed, the labels were then gilded with hand-applied gold leaf. Finally, the labels were embossed using huge 30-ton presses. According to Joe Davidson, the eminent American art dealer and collector, the "Golden Era" of cigar labels is associated with the introduction of gilding and embossing in the 1890's up to the late 1920's when the less attractive full-colour or photo-mechanical labels began to appear. Genuine gold leaf was used primarily by German and Cuban printers and "bronzing" in which bronze powder was mixed with lacquer or sizing, applied like ink, then burnished with brushes or polished rollers to make them gleam like gold. These particular labels were produced by the German factory, Gerhard Meinesz in Bentheim, near the Dutch border, and closed in 1932. The labels were used during the 1920's. These spectacular lithographs lithographs wound up lying unused and undiscovered for generations. Because they were printed on special long-fibre, acid-free rage paper, these old labels retained their original brilliant colours. Consequently, they are available in very limited quantities.
(Funding) Funded in part by the Institute for Museum and Library Services (IMLS), Ephemeral Cities Project.
Tampa |z 1271000 |2 ceeus
Hillsborough County |z 12057 |2 ceeus
United States of America -- Florida -- Hillsborough County -- Tampa

Droits : All rights reserved. 2005.
C24-05393

Extrait de : Contribution à l'étude des bois de la Guyane Française (entre p. 138 et p. 139)
Résumé : (Enterolobium ). II C. transversale dans les fibres ; - rayons médullaires plus fins, plus allongés et C.radiale
Siècle(s) traité(s) : 20
Droits : Domaine public
Permalien : http://www.manioc.org/images/GAD120260177
GAD120260177

Éditeur(s) : HAL CCSD Lavoisier
Résumé : International audience
Afin de réduire la consommation d'énergie électrique liée à l'utilisation intense de la climatisation dans les logements des régions tropicales de la Caraïbe, des matériaux composites fibres végétales/ciment ont été préparés en vue d'être utilisés dans le domaine de la construction. Les fibres de dictame (Maranta arundinacée), résidus de l'extraction de la farine de dictame, sont étudiées. Dans cet article, une première partie sera consacrée à la détermination des dimensions des particules et de la composition chimique des fibres de dictame brutes, à l'étude des évolutions structurales et de texture des fibres après leur pyrolyse (200 - 700°C). Puis le travail sur la prise des composites fibres de dictame/ciment sera mené. En particulier, l'influence de paramètres tels que la teneur en fibres, la teneur en eau et la température de pyrolyse des fibres de dictame sera abordée. Par ailleurs les chaleurs dégagées lors de la dégradation thermique des composites sont également déterminées.
ISSN: 1169-7954

hal-00809828
https://hal.univ-antilles.fr/hal-00809828
DOI : 10.3166/rcma.17.327-350

Éditeur(s) : Apud Frid. Fleischer in comm
Extrait de : Flora brasiliensis. Volumen III. Pars II (après index)
Résumé : I. Raphia II. Palmier-bâche ou Aguaje. Famille des Arecaceae
I. La fibre de raphia est utilisée pour tresser de nombreux objets. II. palmier de la famille Arecaceae aux fruits commestibles

Permalien : http://www.manioc.org/images/TLS17061-0437i1
TLS17061-0437i1

Résumé : Label 7439 / 4 plates
Around the turn of the 20th century, cigars were advertised and sold mainly by the colourful, intricate labels that adorned the boxes. Intense competition encouraged manufacturers to see who could create the most beautiful, eye-catching labels. A diffrent stone was required to print each colour. It was not unusual for as many as 20 stones to be used to create a single label. The register for each printing had to be perfect. The process became known as STONE LITHOGRAPHY or CHROMOLITHOGRAPHY. Once this exacting printing process was completed, the labels were then gilded with hand-applied gold leaf. Finally, the labels were embossed using huge 30-ton presses. According to Joe Davidson, the eminent American art dealer and collector, the "Golden Era" of cigar labels is associated with the introduction of gilding and embossing in the 1890's up to the late 1920's when the less attractive full-colour or photo-mechanical labels began to appear. Genuine gold leaf was used primarily by German and Cuban printers and "bronzing" in which bronze powder was mixed with lacquer or sizing, applied like ink, then burnished with brushes or polished rollers to make them gleam like gold. These particular labels were produced by the German factory, Gerhard Meinesz in Bentheim, near the Dutch border, and closed in 1932. The labels were used during the 1920's. These spectacular lithographs lithographs wound up lying unused and undiscovered for generations. Because they were printed on special long-fibre, acid-free rage paper, these old labels retained their original brilliant colours. Consequently, they are available in very limited quantities.
(Funding) Funded in part by the Institute for Museum and Library Services (IMLS), Ephemeral Cities Project.
Tampa |z 1271000 |2 ceeus
Hillsborough County |z 12057 |2 ceeus
United States of America -- Florida -- Hillsborough County -- Tampa

Droits : All rights reserved. 2005.
C24-05394

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Various bagasse fibre/cement composites have been prepared, the fibres having a random distribution in the composites. The influence of different parameters on the setting of the composite material has been studied: (1) botanical components of the fibre, (2) thermal or chemical treatment of the fibre, (3) bagasse fibre content and (4) added water percentage. This study shows a retarding effect of lignin on the setting of the composite, for small amount of heat-treated bagasse (200 °C) the behaviour of the composite is closely the same as the classical cement or cellulose/cement composite.
ISSN: 0958-9465

hal-00809715
https://hal.univ-antilles.fr/hal-00809715
DOI : 10.1016/S0958-9465(02)00003-3

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This paper examines the thermal properties of cement composites reinforced with vegetable bagasse fibres (1.5% and 3% wrtc). Thermal properties have been correlated to macroscopic density and porosity in order to estimate thermal conductivity of fibres using a calculation inspired from the Maxwell-Eucken modelling. Experimental investigations reveal that adding retified bagasse fibres reduces composites thermal conductivity and yields a weaker specific heat in comparison with composites made with alkaline bagasse fibres. Moreover, the more the fibres, the lighter the specimen; lower its thermal conductivity and lower its specific heat. Thermal conductivity of alkaline fibres is lower than retified fibres one.
ISSN: 1359-835X

hal-00809831
https://hal.univ-antilles.fr/hal-00809831
DOI : 10.1016/j.compositesa.2010.01.002

Éditeur(s) : Université des Antilles et de la Guyane. Faculté des lettres et sciences humaine Musée Départemental d'Archéologie Précolombienne et de la Préhistoire Conseil général de la Martinique Association Ouacabou
Extrait de : 24e congrès international de l'Association internationale d'archéologie de la Caraïbe, du 24 au 29 juillet 2011. Université des Antilles et de la Guyane"
Description : Monsieur Torres nous présente un travail intéressant sur la présence et l'utilisation de coton et d'autres fibres végétales par les Amérindiens à l'époque des contacts avec les Européens.
Siècle(s) traité(s) : 21
Droits : CC-BY-NC-ND - Attribution - Pas d'utilisation commerciale - Pas de modification
Permalien : http://www.manioc.org/fichiers/V12063
V12063

Résumé : Herbácea perenne, con rizoma corto y grueso. Hojas en rosetas basales ovadas o elípticas, de márgenes enteros o dentados, largo pediceladas. Inflorescencia en escapo de hasta 50 cm de largo; espigas linear-cilíndricas, densas, de 5 a 25 cm; flores sésiles; sépalos ovados, verdes. Cápsula elipsoide de 2 a 4 mm, con 5 o más semillas.
Herbacée pérenne, à rhizome court et gros. Feuilles en rosettes basales ovées ou elliptiques, à bords entiers ou dentés, avec longs pédicelles. Inflorescence sur hampe pouvant atteindre 50 cm de long; épis linéaires-cylindriques, denses, de 5 à 25 cm; fleurs sessiles; sépales ovés, verts. Capsule ellipsoïdale de 2 à 4 mm, avec 5 graines ou davantage.
Annual or perennial acaulescent herb with a taproot producing numerous fibrous lateral roots. Leaves, glabrous, forming a basal rosette, petioles 2-15 cm long, blades ovate to elliptic, 2.5-25 x 3-12 cm, base abruptly narrow, apex obtuse, margins coarsely dentate; inflorescence a spike spike, linear-cylindrical, 5-25 cm x 6-8 mm, scape 10-30 cm. long; flowers perfect, corolla lobes 0.5-1 mm long, numerous, sessile, green; fruit a capsule ovate-elliptic 3-4 mm long, seeds brown, oblong 1 x 0.7 mm.
Oriunda del viejo mundo, naturalizada en gran parte del mundo.
Originaire de l’;Ancien Monde, naturalisée dans une grande partie du monde.
Native to the Old World, naturalized in most parts of the world.

http://www.tramil.net/fototeca/plant286

Éditeur(s) : HAL CCSD
Résumé : Composite materials incorporating vegetable fibres have known an increasingly interest during the past few decades. These environmental friendly materials are low-cost and offer advantages such as reduction of electrical consumption by air conditioning. Moreover, the use of vegetable fibres in replacement of synthetic fibre is interesting in developing countries where the availability of tropical plants and agricultural waste is important. This paper presents an initial investigation on the use of a construction material, composed of cement and pre-treated (heat or alkaline treatments) sugar cane bagasse fibres. The purpose of this study is to analyse the effect of fibre content and treatment on thermal conductivity, specific heat, flexural strength and density. The addition of retified fibres reduces composites thermal conductivity and yields a weaker specific heat in comparison with composites made with alkaline fibres. From mechanical point of view, composites made with alkaline fibres have a better flexural strength than others.
12th International Inorganic-bonded Fiber Composites Conference
Aalborg, Denmark

hal-00807543
https://hal.univ-antilles.fr/hal-00807543

Éditeur(s) : HAL CCSD
Résumé :  
Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rain forest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood, and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-01032051
https://hal.archives-ouvertes.fr/hal-01032051

Éditeur(s) : HAL CCSD
Résumé : International audience
A key element of the biomechanical design of trees is their ability to generate largemechanical stresses in wood at the stem periphery. This function is necessary for the tree tocontrol the orientation of its axes, and therefore to grow in height, maintain its branches at anoptimal angle or achieve adaptive reorientations (Fournier et al., 2013). This “maturationstress” appears in wood fibres during their cellular maturation when their secondary cell wallis thickening. In hardwoods, the stress asymmetry is generated by the formation of specificfibres with a very high tensile growth stress on the upper side of the inclined axis. Theresulting tension wood has microstructural features highly different from the normal wood.Tension wood in almost all temperate species has a specific gelatinous cell wall layer, calledG-layer, that is not lignified and highly mesoporous (Chang et al., 2015). It has been shownrecently, at the macroscopic scale, that cellulose tension appears during maturation and issynchronous with the development of this specific layer (Clair et al., 2011). Tropical species,like simarouba, are able to generate lignified tension wood fibres. The mechanisms of stressgeneration in tension wood fibres are not yet well known. The aim of our study is tounderstand these mechanisms and to know the spatial and temporal kinetics of the differentcell wall layers stiffening during maturation, in parallel with tensile stress generation.Contact-Resonance Atomic Force Microscopy, CR-AFM, was used here to address thisquestion on embedded samples (Arnould and Arinero, 2015) using dual resonance frequencytracking (DRFT, Rodriguez et al., 2007). Change in the contact modulus between, and within,each layer of the cell wall has been measured on several radial lines of developing fibres atdifferent steps. In order to understand the obtained results, and to estimate the sensitivity ofthe AFM indentation-like technique to the different cell wall components stiffness, an elasticanisotropic indentation model was used (Vlassak et al., 2003; Jäger et al., 2011). Finally,these mechanical measurements have been compared to topochemical data obtained on thesame fibres.
8th Plant Biomechanics International Conference
Nagoya, Japan

hal-01436113
https://hal.archives-ouvertes.fr/hal-01436113

Éditeur(s) : HAL CCSD E Schweizerbart Science Publishers
Résumé : The occurrence and preservation of aragonite in eclogite-facies rocks of north-eastern Corsica is linked to an uncommon microtexture. Aragonite exclusively occurs as oriented fibres in garnet crystals of a graphitic, more or less siliceous marble that immediately overlies a serpentinite body of the meta-ophiolitic unit. The arrangement of the fibres is grossly radial, but more clearly sectoral in subhedral garnet, the fibres growing perpendicular to the garnet/matrix interface. Raman mapping reveals that the carbonate is calcite in the matrix and in poikiloblastic garnet cores, and that the fibres in the garnet mantle are aragonite alone in the case of a carbonate matrix, and both aragonite and quartz (in distinct fibres) in a quartz–carbonate matrix. These features are interpreted as prograde intergrowths, the result of garnet nucleation and growth in a calcite and then aragonite matrix (±quartz). Upon further heating and/or decompression, the aragonite matrix transformed back to calcite while the carbonates included in garnet retained their original structure, in spite of the relatively high temperature attained (ca. 500 °C). These aragonite relics are one more example of the preservation of a high-pressure polymorph through mechanical shielding of inclusions in a rigid host. The aragonite–garnet intergrowths are similar to quartz–garnet intergrowths described in amphibolite-facies graphitic schists. They are evidence that oriented inclusions in garnet are not necessarily precipitates (‘exsolutions'). Unlike precipitates, their orientation is controlled more by the shape of the garnet growth front than by symmetry constraints.
ISSN: 0935-1221

hal-00411136
https://hal.archives-ouvertes.fr/hal-00411136
DOI : 10.1127/0935-1221/2008/0020-1892

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Transverse drying shrinkage was measured at microscopic and mesoscopic levels in poplar wood characterised by an increasing growth strain (GS), from normal to tension wood. Results show that: (a) The drying shrinkage, measured as a relative thickness decrease, was significantly higher for G-layer (GL) than the other layers (OL), GL shrinkage was not significantly correlated with GS and OL shrinkage was negatively correlated with GS. (b) In gelatinous fibre (G-fibre), lumen size increased during drying and this increase was positively related with GS, but in normal wood fibre lumen size decreased during drying. These findings suggest that GL shrank outwards, so that its shrinkage feebly affected the total cell shrinkage and the mesoscopic shrinkage was controlled by the OL shrinkage which shrank inwards. (c) Measurements done on 7×7 mm² thin sections evidenced a negative correlation between transverse shrinkage and GS, significant in T direction but weak in R direction. These observations at both levels allow to discuss the contribution of GL to the mesoscopic shrinkage of tension wood.
ISSN: 0043-7719

hal-00194930
https://hal.archives-ouvertes.fr/hal-00194930
https://hal.archives-ouvertes.fr/hal-00194930/document
https://hal.archives-ouvertes.fr/hal-00194930/file/WST_FANG2006.pdf
DOI : 10.1007/s00226-007-0148-3

Éditeur(s) : HAL CCSD
Résumé : International audience
Tension wood, a tissue developed by angiosperm trees to actively recover their verticality, has long been defined by the presence of an unlignified cellulosic inner layer in the cell wall of fibres, called the G-layer. Although it was known that some species have no G-layer, the definition was appropriate since it enabled easy detection of tension wood zones using various staining techniques for either cellulose or lignin. For several years now, irrespective of its anatomical structure, tension wood has been defined by its high mechanical internal tensile stress. This definition enables screening of the diversity of cell walls in tension wood fibres. Recent results obtained in tropical species with tension wood with a delay in the lignification of the G-layer opened our eyes to the effective presence of large amounts of lignin in the G-layer of some species. This led us to review older literature mentioning the presence of lignin deposits in the G-layer and give them credit. Advances in the knowledge of tension wood fibres allow us to reconsider some previous classifications of the diversity in the organisation of the fibre walls of the tension wood.
ISSN: 0928-1541

hal-01636686
https://hal.archives-ouvertes.fr/hal-01636686
https://hal.archives-ouvertes.fr/hal-01636686/document
https://hal.archives-ouvertes.fr/hal-01636686/file/2017_Ghislain-Clair_IAWAJ_DiversityOrganisationLignificationTensionWoodFibreWalls-AReview.pdf
DOI : 10.1163/22941932-20170170

Éditeur(s) : HAL CCSD
Résumé : International audience
Trees can control their shape and resist gravity thanks to their ability to produce wood under tensile stress. This stress is known to be produced during the maturation of wood fibres but the mechanism of its generation remains unclear. This study focuses on the formation of the secondary wall in tension wood produced in artificially tilted poplar saplings. Thickness of secondary wall layer (SL) and gelatinous layer (GL) were measured from cambium to mature wood in several trees sampled at different times after tilting. Measurements on wood fibres produced before tilting show the progressive increase of secondary wall thickness during the growing season. After the tilting date, SL thickness decreased markedly from normal wood to tension wood while the total thickness increased compared to normal wood, with the development of a thick GL. However, even after GL formation, SL thickness continues to increase during the growing season. GL thickening was observed to be faster than SL thickening. The development of the unlignified GL is proposed to be a low cost, efficient strategy for a fast generation of tensile stress in broadleaved trees.
IAWA journal / International Association of Wood Anatomists.

hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277/document
https://hal.archives-ouvertes.fr/hal-01229277/file/AbediniClair-Iawa-TensionCellWallThickening_preprint_HAL.pdf
DOI : 10.1163/22941932-00000084

Éditeur(s) : HAL CCSD
Résumé : International audience
The anatomy of tension wood and opposite wood was compared in 21 tropical rain forest trees from 21 species belonging to 18 families from French Guyana. Wood specimens were taken from the upper and lower sides of naturally tilted trees. Measurement of the growth stress level ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile-stressed wood on the upper side, called tension wood and normally tensile-stressed wood on the lower side, called opposite wood. Quantitative parameters relating to fibres and vessels were measured on transverse sections of both tension and opposite wood to check if certain criteria can easily discriminate the two kinds of wood. We observed a decrease in the frequency of vessels in the tension wood in all the trees studied. Other criteria concerning shape and surface area of the vessels, fibre diameter or cell wall thickness did not reveal any general trend. At the ultrastructural level, we observed that the microfibril angle in the tension wood sample was lower than in opposite wood in all the trees except one (Licania membranacea).
IAWA Journal

hal-00194915
https://hal.archives-ouvertes.fr/hal-00194915
https://hal.archives-ouvertes.fr/hal-00194915/document
https://hal.archives-ouvertes.fr/hal-00194915/file/IAWA2006_RuelleClairBeauchenePrevostFournier_ccsd.pdf
IRD : PAR00001321

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Sensitive instruments like strainmeters and tiltmeters are necessary for measuring slowly varying low amplitude Earth deformations. Nonetheless, laser and fibre interferometers are particularly suitable for interrogating such instruments due to their extreme precision and accuracy. In this paper, a practical design of a simple pendulum borehole tiltmeter based on laser fibre interferometric displacement sensors is presented. A prototype instrument has been constructed using welded borosilicate with a pendulum length of 0.85 m resulting in a main resonance frequency of 0.6 Hz. By implementing three coplanar extrinsic fibre Fabry-Perot in-terferometric probes and appropriate signal filtering, our instrument provides tilt measurements that are insensitive to parasitic deformations caused by temperature and pressure variations. This prototype has been installed in an underground facility (Rustrel, France) where results show accurate measurements of Earth strains derived from Earth and ocean tides, local hydro-logic effects, as well as local and remote earthquakes. The large dynamic range and the high sensitivity of this tiltmeter render it an invaluable tool for numerous geophysical applications such as transient fault motion, volcanic strain and reservoir monitoring.
ISSN: 0956-540X

hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967/document
https://hal.archives-ouvertes.fr/hal-01265967/file/HCS1.pdf
DOI : 10.1093/gji/ggv358

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Abstract View references (35)La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) hollow fibres were prepared by a phase inversion/sintering method using polyetherimide as a binder. In order to overcome surface exchange kinetics limitation, LSCF hollow fibres were coated with ∼200nm palladium (Pd) nanoparticles. The O2 flux of best performing membranes increased by up to 350% in comparison to unmodified LSCF hollow fibres. Optimal enhancement was achieved with a single Pd coating. Additional coatings resulted in reduced O2 fluxes, thus counter acting the beneficial spill-over effect of the catalyst. Long term stability testing in atmospheric air at 850°C showed that a LSCF membrane modified with a single Pd coating continually outperformed a pure LSCF hollow fibre for over 400h, though the level of enhancement was reduced over time. A dramatic reduction in performance of more than 45% occurred within the first 24h of testing, which was attributed to the coalescence and aggregation of Pd catalyst particles to ∼1000nm size at the LSCF grain boundaries. This greatly reduced the available area for the oxygen species to spill-over onto the LSCF surface and thus reduced the overall O2 flux. © 2011 Elsevier B.V.
ISSN: 0376-7388

hal-01683196
https://hal.univ-antilles.fr/hal-01683196
DOI : 10.1016/j.memsci.2011.07.008

Éditeur(s) : HAL CCSD
Résumé : Couche G ou couche tertiaire : quel nom pour la couche interne des fibres du bois de tension ?. 11es Journées du Réseau Français des Parois
11es Journées du Réseau Français des Parois
Orléans, France

hal-01603178
https://hal.archives-ouvertes.fr/hal-01603178
PRODINRA : 398652