Éditeur(s) : University of West Indies, Trinidad &Tobago Université des Antilles. Service commun de la documentation
Extrait de : 52e congrès annuel de la Société caribéenne des plantes alimentaires / 52nd annual meeting of the Caribbean food crops society (CFCS), du 10 au 16 juillet 2016. INRA, CFCS
Description : Carbon dioxide (CO2) accounts for the largest proportion (74%) of total greenhouse gas (GHG) emissions globally, with agricultural activities contributing approximately 25% of this gas. Opportunities to reduce the emissions in the sector can therefore contribute significantly to mitigating global climate change. Ag-lime is used extensively to alleviate problems of soil acidity and the potential for this material to contribute to C sequestration in soils is gaining interest among researchers. A laboratory experiment using C-13 isotopic labelling techniques was therefore established to answer the following questions: 1) Is there a potential for sequestering C using ag-lime in Trinidad acid soils? 2) Does enhancing soil microbial respiration by applying labile organic amendments enhance the C sequestration potential of ag-lime? 3) Are lime-derived C (LDC) estimates from non-isotopic difference technique comparable to that from the C- 13 isotopic labelling technique? The results ascertained for the study showed significant (P<0.05) differences between the LDC estimates from the two techniques with the non-isotopic techniques yielding higher estimates. Over the 32- day experiment, between 16.4 to 85.4% of the ag-lime C was released as CO2 with values being lower for the Piarco soil. The LDC in the CO2 was also significantly (P<0.05) lower for the poultry litter treatments comparison to the other organic amendments for the Piarco soil but not the Nariva soil. This effect may not have been as a result of an enhancement of the carbon sequestration potential of the ag-lime due to an elevation in soil microbial respiration since the LDC in the glucose-amended soils did not differ significantly from the no-amendment control soils.
Siècle(s) traité(s) : 21
Droits : CC-BY-NC-ND - Attribution - Pas d'utilisation commerciale - Pas de modification
Permalien : http://www.manioc.org/fichiers/V16308
V16308

Éditeur(s) : Elsevier
Résumé : A study of organic carbon mineralization from the Congo continental shelf to the abyssal plain through the Congo submarine channel and Angola Margin was undertaken using in situ measurements of sediment oxygen demand as a tracer of benthic carbon recycling. Two measurement techniques were coupled on a single autonomous platform: in situ benthic chambers and microelectrodes, which provided total and diffusive oxygen uptake as well as oxygen microdistributions in porewaters. In addition, sediment trap fluxes, sediment composition (Org-C, Tot-N, CaCO3, porosity) and radionuclide profiles provided measurements of, respectively input fluxes and burial rate of organic and inorganic compounds. The in situ results show that the oxygen consumption on this margin close to the Congo River is high with values of total oxygen uptake (TOU) of 4 +/- 0.6, 3.6 +/- 0.5 mmol m(-2) d(-1) at 1300 and 3100m depth, respectively, and between 1.9 +/- 0.3 and 2.4 +/- 0.2 mmol m(-2) d(-1) at 4000 m depth. Diffusive oxygen uptakes (DOU) were 2.8 +/- 1.1, 2.3 +/- 0.8, 0.8 +/- 0.3 and 1.2 +/- 0.1 mmol m(-2) d(-1), respectively at the same depths. The magnitude of the oxygen demands on the slope is correlated with water depth but is not correlated with the proximity of the submarine channel-levee system, which indicates that cross-slope transport processes are active over the entire margin. Comparison of the vertical flux of organic carbon with its mineralization and burial reveal that this lateral input is very important since the sum of recycling and burial in the sediments is 5-8 times larger than the vertical flux recorded in traps. Transfer of material from the Congo River occurs through turbidity currents channelled in the Congo valley, which are subsequently deposited in the Lobe zone in the Congo fan below 4800 m. Ship board measurements of oxygen profiles indicate large mineralization rates of organic carbon in this zone, which agrees with the high organic carbon content (3%) and the large sedimentation rate (19 mm y(-1)) found on this site. The Lobe region could receive as high as 19 mol C m(-2) y(-1), 1/3 being mineralized and 2/3 being buried and could constitute the largest depocenter of organic carbon in the South Atlantic.
Deep Sea Research Part II: Topical Studies in Oceanography (0967-0645) (Elsevier), 2009-11 , Vol. 56 , N. 23 , P. 2223-2238

Droits : 2009 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/2009/publication-7316.pdf
DOI:10.1016/j.dsr2.2009.04.005
http://archimer.ifremer.fr/doc/00000/7316/

Éditeur(s) : HAL CCSD
Résumé : International audience
In boundary lubrication regime, friction reduction and antiwear processes are associated to the presence of additives in the lubricating oils or greases. These processes are due to the formation of protective tribofilms resulting from chemical reactions between the additives and the sliding surfaces, in the physico-chemical conditions of the sliding contact. Conventional antiwear additives mainly consist of transition metal organo phosphate or thiophosphates which present a remarkable efficiency in the case of contacts between ferrous alloys. In the case of non reacting surfaces, these additives become inactive. Recently developped lubrication strategies consist in the use of dispersion in oils of nano additives able to build the protective tribofilm in the sliding contact without reaction with the surfaces. Carbon fluorinated phases, due to their lamellar structure and their high chemical stability even at relatively high temperature (400°C) represent interesting candidates as lubricant nano-additives subjected to present friction reduction, anti wear and anti corrosion actions. This work presents the tribologic behaviour of some carbon fluorinated derivatives such as graphite fluorides, fluorinated carbon nanofibers, fluorinated carbon nanodiscs and fluorinated carbon blacks. The influence, on the tribologic performances, of the structure of the initial carbon phases, of the fluorination rate (0
World Tribology Congress 2013
Torino, Italy

Droits : info:eu-repo/semantics/OpenAccess
hal-00926514
https://hal.archives-ouvertes.fr/hal-00926514
https://hal.archives-ouvertes.fr/hal-00926514/document
https://hal.archives-ouvertes.fr/hal-00926514/file/Delbe_9783.pdf
OATAO : 9783

Éditeur(s) : Elsevier Science Bv
Résumé : Mechanisms controlling the transfer and retention of silicon (Si) along continental margins are poorly understood, but play a major role in the functioning of coastal ecosystems and the oceanic biological pump of carbon. Deep-sea fans are well recognized as carbon sink spots, but we lack knowledge about the importance of the fans in the global Si cycle. Here, we provide a first estimate of the role played by the Congo deep-sea fan, one of the biggest in the world, in the Si cycle. Sediment cores sampled in the deep-sea fan were analyzed to build a Si mass balance. An exceptionally high accumulation rate of amorphous silica aSiO(2) (2.29 +/- 0.58 mol Si m(-2) y(-1)) was found, due to a high sedimentation rate and the presence of aluminum in the sediments. Although favored by bioirrigation, recycling fluxes remained low (0.3 mol Si m(-2) y(-1)) and reconstructed input fluxes could only be explained by lateral inputs coming from the canyon. Preliminary calculations show that the rapid transport of aSiO(2) through the canyon and the excellent preservation efficiency in the sediments imply that 50% of aSiO(2) river inputs from the Congo River accumulate annually in the deep-sea fan. Si:C ratios in deep-sea fan sediments were very low (0.2) and only three times as high as those measured in the river itself, which suggests that material from the river and the continental shelf was delivered directly through the canyon, with very little time for Si and C cycle decoupling to take place.
Journal Of Marine Systems (0924-7963) (Elsevier Science Bv), 2015-01 , Vol. 141 , P. 71-79

Droits : 2014 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/00251/36242/35797.pdf
DOI:10.1016/j.jmarsys.2014.07.010
http://archimer.ifremer.fr/doc/00251/36242/

Éditeur(s) : Gauthier-Villars
Résumé : Five particle traps were deployed at depths of 4 400 to 4 900 rn at two stations on the Demerara abyssal plain and one station on the Cape Verde abyssal plain (tropical Atlantic). At the same time, an intensive sampling of superficial sediments was carried out using a 0,25 m2 box corer. The total particle flux varied from 372 to 87,7 mg dry weightfm2/day. The average concentration of organic carbon was 40 mg/g of material collected. ln the surface sediment this was only 4 mg/g. A direct relationship existed between the intensity of the flux of organic matter and the richness of the organic matter of the deposited sediment. According to our calculations, more than 90% of the organic matter arriving at the bottom is consumed by the abyssal benthos and only 1% is lost to permanent sediment deposits. For 100 calories consumed by the benthos, 99 are utilized by the infauna and flora, 0, 7 by the holothurian egafauna and 0,3 by near-bottom fisches. The biochemical composition of the particles is characterized at ali stations by a predominance of "humic" material in the total organic matter (more than 55%). The part of the molecules unaltered form living material varied from on station to another: for the most oceanic station the protein dominated, composing 20% of the total energy. At the station onder the influence of the continent the lipid fraction grew and was almost equal to that of the protein. ln this case, the carbohydrate fraction was very weak (7% of the organic matter). Finally the preference of the animais which feed on the particles is principally for the most energetic (lipid) and the most easily hydrolysable (labile protein) molecules: the other molecules, such as the humic matter, are less preferred, although they still contribute to about half of the energy consumed by the abyssal benthic animais.
Cinq pièges à particules ont été déployés à des profondeurs comprises entre 4400 et 4 900 rn sur deux stations dans la plaine abyssale de Demerara et une station dans la plaine abyssale du Cap Vert (Atlantique tropical). Dans le même temps, un échantillonnage intensif du sédiment superficiel a été réalisé à l'aide d'un carottier de 0,25 m2 d'ouverture. Le flux particulaire total mesuré varie de 372 mg de matière sèche/m2/jour à 87,7 mg/m2/g de matériel récolté. Dans les sédiments superficiels, elle n'est plus que d'environ 4 mg/g. Il existe une relation directe entre l'intensité du flux organique et la richesse en composés organiques du sédiment. D'après nos estimations, plus de 90% du matériel organique arrivant sur le fond sont consommés par les organismes benthiques abyssaux et seulement 1% est perdu dans la sédimentation permanente. Pour 100 calories consommées par le benthos, 99 le sont par la petite faune et la flore vivant dans le sédiment, 0, 7 calories sont utilisées par les holothuries (mégafaune) et 0,3 calories par les poissons. La composition biochimique des particules se caractérise, à toutes les stations, par la prédominance des composés organiques transformées néobiogéniques ( « humus ») dans la matière organique totale (plus de 55%). La part des molécules de la matière vivante varie d'une station à l'autre: à la station la plus océanique, les protéines dominent et composent 200/o de l'énergie totale des apports. Dans la station plus soumise aux influences continentales, la concentration en lipides augmente et peut égaler celle des protéines. Dans ce cas, le taux de glucides des particules est très faible (7% des apports organiques). Enfin, les préférences nutritionnelles des animaux qui s'alimentent sur ces particules se portent principalement sur les molécules les plus énergétiques (lipides) et les plus facilement hydrolysables (protéines labiles) : les autres molécules, comme les composés néobiogéniques sont moins recherchés bien qu'ils contribuent pour moitié à l'énergie consommée par les animaux benthiques abyssaux
Oceanologica Acta (0399-1784) (Gauthier-Villars), 1985 , Vol. 8 , N. 3 , P. 293-301

Droits : Gauthier-Villars
http://archimer.ifremer.fr/doc/00112/22318/19991.pdf
http://archimer.ifremer.fr/doc/00112/22318/

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
PurposeMarine mangrove sediments in the Manche-à-Eau lagoon (Guadeloupe, Caribbean Sea) harbor locally extensive, white microbial mats. These mats cover the surface of reduced sediments near the roots of red mangrove trees, Rhizophora mangle, and are mainly composed of sulfur-oxidizing bacteria belonging to the Beggiatoaceae family, with some filamentous cyanobacteria. The goal of this study was to investigate the possible influence of sediment characteristics on the presence of these microbial mats.Materials and methodsFour push cores were collected in April 2013, two from zones with microbial mats and two from zones without mats. Sediment characteristics (grain-size distribution, mineralogy, total organic carbon (TOC) and total nitrogen (TN) contents, atomic TOC/TN ratios, and organic matter (OM) δ13C values) were compared for all four cores.Results and discussionSignificant differences were observed between sediments below microbial mats and those without mats. Sediments with microbial mats contained greater amounts of clay, and higher TOC, TN, and TOC/TN ratios, with lower total carbonate content and δ13C values. The higher clay content most likely results from lower fluid flow velocity near to mangrove roots, while higher TOC/TN ratios and lower δ13C values indicate higher inputs of OM from mangrove trees. These results are consistent with the fact that microbial mats were observed near the roots of mangrove trees, which trap OM from terrestrial vegetation and fine sediments.ConclusionsThe grain-size distribution of sediment particles, the total carbonate content, and the δ13C values are the main parameters discriminating between zones with microbial mats and those without mats. Variations in total carbonate content, which is mainly of biogenic origin, result from conditions that are more favorable for benthic organisms in zones without microbial mats. Variations of the TOC/TN ratios are controlled by the presence of a non-negligible amount of inorganic nitrogen bound to surface clay mineral particles and/or by microbial processes.
ISSN: 1439-0108

hal-01545903
https://hal.archives-ouvertes.fr/hal-01545903
DOI : 10.1007/s11368-016-1555-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : This study analyzes the records of several trace metals sensitive to redox conditions in continental shelf sediments off Concepcion, Chile (36 degrees S). The continental margin off Concepcion (36 S; 73 W) lies beneath an important upwelling center characterized by high primary production rates and, consequently, high fluxes of organic matter. In spring and summer, this material settles to the seafloor where it decays, producing periods of very low oxygen content in bottom waters (<1 mL L-1). In addition, an oxygen minimum zone develops at similar to 100-400 m water depth, where dissolved oxygen levels are <0.5 mL L-1. This situation changes during strong El Nino events, when dissolved oxygen at the bottom increases drastically (>1 mL L-1).;The goals of this study were to determine the input of trace metals to the sediment and to decipher how this information can be used to reveal variations in primary productivity or bottom oxygenation. Gravity cores collected at two stations - VG06-2 over the mid-shelf station (88 m water depth, upper boundary of the oxygen minimum zone) and VG06-3 over the outer shelf (120 m water depth, within the oxygen minimum zone) - were sampled for high resolution profiles (1 cm) of trace metals, biogenic opal, stable isotopes, and total organic carbon. The results suggest that the variability in the trace metal distribution on the continental shelf off Concepcion is determined by redox conditions and the organic carbon flux to the bottom. Some sections of the sediment cores from the outer shelf showed appreciable authigenic enrichment of U, Cd, and Mo (EF: 5-10, 2-5, and 10-16 respectively) along with heavier values of delta N-15, suggesting periods of suboxic conditions. During these periods, fluxes of organic material to the bottom were higher, as indicated by elevated TOC and opal contents. Alternating periods of higher and lower trace metal contents were not observed mid-shelf as they were on the outer shelf. Rather, the mid-shelf samples showed authigenic enrichment of U, Cd, and Mo (EF: 1-6, 4-5, and 10-20, respectively) throughout the core except in a 10-cm-thick gray layer. In general, authigenic enrichment of U. Mo, and Cd occurred at both sites, coincident with olive green layers in the cores. These layers were associated with periods of elevated primary productivity and suboxic conditions. Such periods did not seem to last as long as the oxygenated periods, which had higher inputs of refractive detrital material, coincident with the occurrence of distinct gray sediment layers.
ISSN: 0079-6611

hal-00682159
https://hal.archives-ouvertes.fr/hal-00682159
DOI : 10.1016/j.pocean.2011.07.010

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
This work is concerned with the study of the tribologic properties of room temperature fluorinated graphite heat-treated under fluorine atmosphere. The fluorinated compounds all present good intrinsic friction properties (friction coefficient in the range 0.05–0.09). The tribologic performances are optimized if the materials present remaining graphitic domains (influenced by the presence of intercalated fluorinated species) whereas the perfluorinated compounds, where the fluorocarbon layers are corrugated (armchair configuration of the saturated carbon rings) present higher friction coefficients. Raman analyses reveal that the friction process induces severe changes in the materials structure especially the partial re-building of graphitic domains in the case of perfluorinated compounds which explains the improvement of μ during the friction tests for these last materials.
ISSN: 1023-8883

hal-00767637
https://hal.archives-ouvertes.fr/hal-00767637
https://hal.archives-ouvertes.fr/hal-00767637/document
https://hal.archives-ouvertes.fr/hal-00767637/file/Delbe_6329.pdf
DOI : 10.1007/s11249-009-9487-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : Une approche par datations multiples a été menée sur les dépôts de sédiments de crue retrouvés dans les gorges du Gardon (Languedoc). Le plomb-210, le césium-137 et l’analyse géochimique des sédiments contaminés par les mines ont été utilisés pour reconstruire l’histoire des dépôts de crue. Cette approche a été combinée avec l’historique des crues du Gardon depuis 1890 pour affiner l’approche géochronologique. Au niveau de la cavité GG et de la terrasse GE les analyses ont permis d’illustrer les mécanismes d’érosion-redéposition pouvant perturber les séquences de sédiments. Les enregistrements des dépôts de sédiments de crue sont complets sur la terrasse GE située à 10 m au-dessus du lit mineur à partir de 1958, et incomplets auparavant. Sur la période 1880-1958, 25 crues ont eu un débit suffisant (>1450 m3/s) pour recouvrir la terrasse, alors que l’on recense seulement 5 à 6 crues depuis 1958 (pour un débit de submersion supérieur à 1700 m3/s). L’augmentation progressive du débit de submersion et la fréquence moindre d’inondation de la terrasse ont pu permettre sur la période récente la stabilisation de la couche de surface par la végétation et limiter l’érosion lors de crues importantes. Les enregistrements semblent complets dans la cavité GG située à 15 m au-dessus du lit mineur. La fréquence moindre de submersion à ce niveau plus élevé peut expliquer une meilleure stabilisation des dépôts de crue, rendus moins vulnérables à l’érosion. La datation au radiocarbone a été testée même si elle ne permet pas de dater avec précision les dépôts de crue des derniers siècles. Sur la terrasse GE, 80% des dates au carbone 14 sur charbon de bois sont beaucoup trop vieilles par rapport aux autres techniques de datation, ce qui peut s’expliquer par une remobilisation/déstockage de charbons de bois anciens. Les datations radiocarbone sur graines donnent de meilleurs résultats, car issues d’une production annuelle, plus facilement décomposable et moins sujette à des dépôts intermédiaires. Au final, il apparaît que la technique de datation par radiocarbone sur des charbons de bois retrouvés dans les séquences sédimentaires n’est pas fiable, alors qu’elle est la plus pratiquée en paléo-hydrologie. L’utilisation combinée du plomb-210, du césium-137, de l’analyse géochimique des sédiments et des informations sur les crues historiques a permis de discriminer et de dater les différents dépôts de crue de ce dernier siècle dans la cavité GG et la terrasse GE. / A multidating approach was carried out on slackwater flood deposits, preserved in valley side rock cave and terrace, of the Gardon River in Languedoc, southeast France. Lead-210, caesium-137, and geochemical analysis of mining-contaminated slackwater flood sediments have been used to reconstruct the history of these flood deposits. These age controls were combined with the continuous record of Gardon flow since 1890, and the combined records were then used to assign ages to slackwater deposits. The stratigraphic records of terrace GE and cave GG were excellent examples to illustrate the effects of erosion/preservation in a context of a progressively self-censoring, vertically accreting sequence. The sedimentary flood record of the terrace GE located at 10 m above the channel bed is complete for years post-1958 but incomplete before. During the 78-year period 1880-1958, 25 floods of a sufficient magnitude (> 1450 m3/s) have covered the terrace. Since 1958, however, the frequency of inundation of the deposits has been lower:only 5 or 6 floods in 52 years have been large enough to exceed the necessary threshold discharge (> 1700 m3/s). The progressive increase of threshold discharge and the reduced frequency of inundation at the terrace could allow stabilisation of the vegetation cover and improved protection against erosion from subsequent large magnitude flood events. The sedimentary flood record seems complete for cave GG located at 15 m above the channel bed. Here, the low frequency of events would have enabled a high degree of stabilisation of the sedimentary flood record, rendering the deposits less susceptible to erosion. Radiocarbon dating are used in this study and compared to the other dating techniques.Eighty percent of radiocarbon dates on charcoals were considerably older than those obtained by the other techniques in the terrace. On the other hand, radiocarbon dating on seeds provided better results. This discrepancy between radiocarbon dates on charcoal and seeds is explained by the nature of the dated material (permanent wood vs. annual production and resistance to degradation process). Finally, we showed in this study that although the most common dating technique used in paleoflood hydrology is radiocarbon dating, usually on charcoal preserved within slackwater flood sediments, this method did not permitus to define a coherent age model. Only the combined use of lead-210, caesium-137, and geochemical analysis of mining-contaminated sediments with the instrumental flood record can be applied to discriminate and date the recent slackwater deposits of the terrace GE and cave GG.
ISSN: 0169-555X

hal-01059669
https://hal.archives-ouvertes.fr/hal-01059669
https://hal.archives-ouvertes.fr/hal-01059669/document
https://hal.archives-ouvertes.fr/hal-01059669/file/ly2014-pub00040953.pdf
IRSTEA : PUB00040953

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Well-dispersed iron oxide nanoparticles supported onto graphene oxide sheets (i.e. GO-Fe3O4 nanocomposite) were synthesised and used as heterogeneous Fenton-like catalyst for the degradation of Acid Orange 7 dye (AO7). The reaction was systematically investigated under various experimental conditions such as nanocomposite dosage, pH, temperature, oxidant and dye concentrations. Best results showed a fast 80% degradation in ∼20 min, whilst ∼98% of AO7 was successfully removed after 180 min of reaction time. The degradation kinetics of AO7 was most influenced by pH and temperature, and can be described by a pseudo-first-order reaction following the Langmuir-Hinshelwood mechanism. Analysis of the spent nanocomposite suggested that the phase of iron oxide nanoparticles remained unchanged whilst minor pore volume losses occurred via carbon deposition and/or re-stacking of GO sheets. © 2014 Elsevier Ltd.
ISSN: 2213-3437

hal-01683206
https://hal.univ-antilles.fr/hal-01683206
DOI : 10.1016/j.jece.2014.08.001

Éditeur(s) : HAL CCSD E Schweizerbart Science Publishers
Résumé : The occurrence and preservation of aragonite in eclogite-facies rocks of north-eastern Corsica is linked to an uncommon microtexture. Aragonite exclusively occurs as oriented fibres in garnet crystals of a graphitic, more or less siliceous marble that immediately overlies a serpentinite body of the meta-ophiolitic unit. The arrangement of the fibres is grossly radial, but more clearly sectoral in subhedral garnet, the fibres growing perpendicular to the garnet/matrix interface. Raman mapping reveals that the carbonate is calcite in the matrix and in poikiloblastic garnet cores, and that the fibres in the garnet mantle are aragonite alone in the case of a carbonate matrix, and both aragonite and quartz (in distinct fibres) in a quartz–carbonate matrix. These features are interpreted as prograde intergrowths, the result of garnet nucleation and growth in a calcite and then aragonite matrix (±quartz). Upon further heating and/or decompression, the aragonite matrix transformed back to calcite while the carbonates included in garnet retained their original structure, in spite of the relatively high temperature attained (ca. 500 °C). These aragonite relics are one more example of the preservation of a high-pressure polymorph through mechanical shielding of inclusions in a rigid host. The aragonite–garnet intergrowths are similar to quartz–garnet intergrowths described in amphibolite-facies graphitic schists. They are evidence that oriented inclusions in garnet are not necessarily precipitates (‘exsolutions'). Unlike precipitates, their orientation is controlled more by the shape of the garnet growth front than by symmetry constraints.
ISSN: 0935-1221

hal-00411136
https://hal.archives-ouvertes.fr/hal-00411136
DOI : 10.1127/0935-1221/2008/0020-1892

Éditeur(s) : Université de la Rochelle
Résumé : In order to better understand the functioning of the Brouage intertidal mudflat (Marennes- Oléron Basin, France), its carbon-based trophic web has been modelled and analyzed. The foodweb building is based on the 4 step method of Inverse Analysis: 1) conceive an a priori model as the graph of compartments (nodes) between which exist fluxes of material (vertices). These vertices are the unknowns for the problem; 2) gather all the existing knowledge about the ecosystem and translate it into linear equations and inequalities involving the fluxes; 3) complete this set of data by common knowledge on the behaviour of the compartments and translate it into inequalities, 4) solve the obtained linear system under the parsimony principle to find a unique solution vector. The food-web analysis is based on. The first purpose of this work was a methodological one: inverse analysis method has been adapted to consider the seasonal and spatial variability of the temperate ecosystem: two seasons have been coupled in the computation and the area has been divided into three geographical zones along a cross-shore gradient. Hence, two types of physical exchanges are involved: the benthicpelagic ones and the advection ones. Statistical results can also be obtained by coupling Monte Carlo methods to Inverse Analysis. To study the obtained networks, new indices based on Markov Chains take delay into account in describing integrative transfers of material between compartments. This lets emerge the systems' properties that are not obvious at first sight and emphasizes the role of peculiar components. The second purpose was to apply such methods to the Brouage mudflat ecosystem in order to better understand its functioning. As the knowledge and methods evolve, various food webs were computed and analyzed with the help such indices and existing ones. Sensitivity analyses allow to point at the most crucial lacks of knowledge, which can orientate future field research. New data would improve the quality of the model in two ways: one the one hand, they would validate or invalidate the outcomes and on the other hand, they would give useful information to better constrain some of the black boxes and most uncertain fluxes, especially the advection and vertical flows. The main results of the study show a strongly seasonal system in which benthic and pelagic components are linked with intensity. The system is driven by its high local benthic primary production, but also depends on imports from the basin. Each of the 3 geographic zones has a peculiar functioning. The central zone corresponds to the classical description of European intertidal mudflats: very productive, it can feed the other regions. It is a production zone. The upper part is less productive but is fed by the middle one via the water column and can be exploited by shorebirds. It is a degradation zone (material is transformed for less qualitative). The lower part strongly depends on the basin imports for its functioning, as the cultivated bivalves act as a pump for pelagic material of which a great part is deposited under the cultivation structures (oyster racks or mussels "bouchots"). It is a transformation zone.
Un double objectif (méthodologique et appliqué) a été visé par une modélisation du réseau trophique de la vasière de Brouage (Bassin de Marennes Oléron, France) à l'aide de l'analyse inverse, et son étude à l'aide de l'analyse des réseaux. L'Analyse Inverse permet en effet de reconstruire l'ensemble du réseau à partir de données éparses, le problème du manque de données étant récurrent en Ecologie. Au plan méthodologique, l'analyse inverse a été adaptée à la prise en compte des caractères saisonnier et spatialement hétérogène d'un écosystème tempéré de zone intertidale : deux saisons ont ainsi été couplées et la vasière a été considérée le long d'un transect perpendiculaire au rivage et divisé en trois zones spatiales. Deux types de flux physiques interviennent donc : les flux verticaux de dépôt et remise en suspension, et les flux d'advection via la colonne d'eau. Des pistes d'amélioration et de nouvelles méthodes sont proposées. Un résultat sous forme statistique peut être obtenu en couplant l'utilisation de méthodes de Monte Carlo à l'analyse inverse pour la construction des réseaux trophiques. Les moyens d'étude des modèles ont été enrichis par la mise au point d'indices issus de la construction de chaînes de Markov et prenant en compte le caractère temporel des transferts de matière entre compartiments. Enfin, la transformation mathématique du modèle statique pour une étude dynamique de la stabilité de l'équilibre décrit est abordée. Plusieurs modèles ont été construits au cours de l'évolution des méthodes et de l'acquisition de connaissances sur le site. Des méthodes d'analyses existantes et d'autres mises au point dans le cadre de cet ouvrage ont été appliquées aux réseaux obtenus afin de faire émerger les propriétés du fonctionnement de la vasière et de souligner le rôle de certains compartiments. Des analyses de sensibilité permettent d'évaluer la robustesse des résultats et d'orienter les recherches futures en mettant en évidence les manques les plus cruciaux. Des données supplémentaires, notamment concernant les foraminifères benthiques, le zooplancton ou les mouvements verticaux du microphytobenthos permettront de fournir de meilleures contraintes et de valider (ou non) les résultats obtenus. Les principaux résultats montrent un système au fort caractère saisonnier dont les compartiments benthiques et pélagiques sont très liés. La production primaire benthique locale est un moteur important, mais qui ne suffirait pas à suppléer l'indispensable importation de matériel détritique. Le découpage de la vasière en trois zones fait apparaître les particularités de chacune. La zone centrale correspond à la description classique des « vasières intertidales européennes » : très productive, elle peut alimenter les autres régions. C'est une zone de production et d'exportation. La partie supérieure est moins productive et reçoit de la matière de la zone de milieu d'estran via la colonne d'eau. Sa production secondaire peut alors être exploitée par les limicoles, nombreux en hiver. C'est une zone de dégradation et d'exportation. Le bas d'estran dépend fortement des importations extérieures, « pompées » par les bivalves cultivés qui sont ainsi directement responsables d'une forte sédimentation sous les structures mytilicoles et ostréicoles. C'est une zone de transformation.

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/2005/these-2260.pdf
http://archimer.ifremer.fr/doc/00000/2260/

Éditeur(s) : HAL CCSD Royal Society of Chemistry
Résumé : International audience
LA-ICP-MS analysis of the chemical composition of biogenic carbonate has many applications in the environmental sciences but the characteristics of the material produced by the ablation process are largely unknown. To fill this gap, we have undertaken a study of the chemical and physical nature of particles produced by laser ablation of biogenic carbonates. SEM imaging suggests that laser ablation produces two distinct particle populations, one consisting of microsize particles and the other of nanosize particles. A 213 nm laser gives rise to a higher proportion of microsize particles than a 193 nm laser, probably because the 213 nm laser couples less completely with carbonate material. The microsize particles appear to form by photomechanical fracturing along lines of cleavage or weakness, rather than by hydrodynamic sputtering (as is generally observed for silicates). Chemical analysis of the carbonate particles suggests that little chemical fractionation of biogenic carbonates occurs during the ablation process or during transport to the plasma. This is supported by the constancy of the fractionation factor ([X/Ca](measured)/[X/Ca] true) during the course of an ablation of a carbonate standard. In contrast, changes in the fractionation factor during the first few seconds of ablation of the NIST 612 are observed for some elements. This difference in fractionation is likely to result from the different formation mechanisms of the microsize particles.
ISSN: 0267-9477

hal-00411933
https://hal.archives-ouvertes.fr/hal-00411933
DOI : 10.1039/b706727e

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The study of decay resistance in wood is of interest for wood end-users but also for the global carbon balance since wood biodegradation is a key driver of forest ecosystem functioning through its impacts on carbon and nutrient cycling. We studied the density and wood extractive contents in order to understand decay resistance against soil microflora after 90 days exposure of sapwood and heartwood from three Neotropical wood species known for their decay resistance: Bocoa prouacensis, Vouacapoua americana, Inga alba. Decay resistance was correlated with density more than wood extractive content. The results highlighted different decay resistance strategies. In B. prouacensis, both sapwood and heartwood were highly resistant due to the high density and high content of antifungal wood extractives. In V. americana heartwood, decay resistance was due to the high synergistic-acting wood extractive content. Conversely, with the least dense wood species I. alba, we found that decay resistance was due to the antifungal wood extractives synthesized early in the sapwood. In conclusion, we showed that the three wood species with the same level of heartwood decay resistance performance had different decay resistance strategies according to the anatomic and defensive wood traits.
ISSN: 0964-8305

hal-01321162
https://hal.archives-ouvertes.fr/hal-01321162
https://hal.archives-ouvertes.fr/hal-01321162/document
https://hal.archives-ouvertes.fr/hal-01321162/file/Art_Amusant_al_Diversity_decay_resistance_strategies_Int.Biodet.Biodegr._2014.pdf
DOI : 10.1016/j.ibiod.2014.06.012

Éditeur(s) : Pergamon-elsevier Science Ltd
Résumé : We tested the applicability of the BIT (branched and isoprenoid tetraether) index as a proxy for palaeoflood events in the river-dominated continental margin of the Gulf of Lions (NW Mediterranean). We compared the concentrations of branched glycerol dialkyl glycerol tetraethers (br GDGTs) and crenarchaeol in suspended particulate matter (SPM) collected downstream in the Rhône River, as well as in surface sediments and a ca. 8m piston core from the Rhône prodelta. The core covered the last 400 yr, with four distinct intervals recording the river influence under natural and man-induced shifts in four main channels of the river mouth (Bras de Fer, Grand Rhône, Pégoulier,and Roustan). The results indicate that there are mixed sources of br GDGTs and crenarchaeol in the prodelta, complicating applicationof the BIT index as an indicator of continental organic carbon input and thus as a palaeoflood proxy. However, the sedimentary BIT record for the period when continental material was delivered by the river more directly to the core site (Roustan phase;1892 to present) mimics the historical palaeoflood record. This shows the potential of the BIT index as a palaeoflood proxy, provided that the delivery route of the continental material by rivers to the core sites remains constant over time. The study also highlights the idea that shifts in river channels should be taken into account for the use of the BIT index as a palaeoflood proxy.
Organic Geochemistry (0146-6380) (Pergamon-elsevier Science Ltd), 2014-10 , Vol. 75 , P. 99-108

Droits : 2014 Elsevier Ltd. All rights reserved.
http://archimer.ifremer.fr/doc/00198/30969/29345.pdf
DOI:10.1016/j.orggeochem.2014.06.011
http://archimer.ifremer.fr/doc/00198/30969/

Éditeur(s) : HAL CCSD Elsevier Masson
Résumé : International audience
Turbinaria turbinata brown seaweeds were tested as carbon electrode material in symmetric, electrochemical supercapacitors. The electrochemical properties of the carbon materials were characterised for their application as supercapacitors using cyclic voltammetry, galvanostatic charge/discharge method and electrochemical impedance spectroscopic analyses. Our initial results showed that the optimal behaviour was obtained for the sample prepared by pyrolysis at 800 degrees C. The average surface area of the carbon was 812 m(2)/g. Electrochemical tests with an organic electrolyte gave the following interesting results: a capacitance of 74.5 F/g, a specific series resistance of 0.5 Omega cm(2) and an ionic resistivity of 1.3 Omega cm(2). These results show the promising capacitive properties of carbon derived from seaweeds and their application in electrochemical supercapacitors. (C) 2013 Academie des sciences.
ISSN: 1631-0748

hal-00817880
http://hal.upmc.fr/hal-00817880
DOI : 10.1016/j.crci.2012.12.016

Éditeur(s) : HAL CCSD
Résumé : International audience
The porosity (from values of <1% up to more than 50%, with a mean value of 36.5%) and permeability (from very low values to 20.4 D, with a mean value around 800 mD) of 38 plugs, with a diameter 40 mm, have been measured. These plugs were taken approximately every 1.5 m along a 100 m-long core, sampling a series of reefal carbonate platform lithofacies. A non-unique relationship between porosity and permeability is obtained. In addition, the porosity was measured from processing X-ray micro-tomography images with resolutions ranging from 0.42 to 190.0 µm and sampling volumes ranging from less than 1 µm3 to few cm3. Depending on the structure of the pore network, the computed porosity is, in some cases, controlled by the X-ray image resolution and the sampled volume. While high resolution is required to image micro-porous material, large samples with lower resolution images are necessary for identifying distributed vugs and millimetre-scale structures. This study shows that multi-resolution X-ray micro-tomography is an effective tool for characterizing the multi-scale pore structure of carbonate rocks and understanding how it may control key petrophysical parameters such as porosity and permeability.
Geological Society Special Publication

hal-01174157
https://hal.archives-ouvertes.fr/hal-01174157
DOI : 10.1144/SP406.12

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Purpose: Marine mangrove sediments in the Manche-à-Eau lagoon (Guadeloupe, Caribbean Sea) harbor locally extensive, white microbial mats. These mats cover the surface of reduced sediments near the roots of red mangrove trees, Rhizophora mangle, and are mainly composed of sulfur-oxidizing bacteria belonging to the Beggiatoaceae family, with some filamentous cyanobacteria. The goal of this study was to investigatethe possible influence of sediment characteristics on the presence of these microbial mats. Materials and methods: Four push cores were collected in April 2013, two from zones with microbial mats and two from zones without mats. Sediment characteristics (grain-size distribution, mineralogy, total organic carbon (TOC) and total nitrogen (TN) contents, atomic TOC/TN ratios, and organic matter (OM) δ13C values) were compared for all four cores.Results and discussion: Significant differences were observed between sediments below microbial mats and those without mats. Sediments with microbial mats contained greater amounts of clay, and higher TOC, TN, and TOC/TN ratios, with lower total carbonate content andδ13C values. The higher clay content most likely results from lower fluid flow velocity near to mangrove roots, while higher TOC/TN ratiosand lower δ13C values indicate higher inputs of OM from mangrove trees. These results are consistent with the fact that microbial mats were observed near the roots of mangrove trees, which trap OM from terrestrial vegetation and fine sediments.Conclusions: The grain-size distribution of sediment particles, the total carbonate content, and the δ13C values are the main parameters discriminating between zones with microbial mats and those without mats. Variations in total carbonate content, which is mainly of biogenic origin, result from conditions that are more favorable for benthic organisms in zones without microbial mats. Variations of the TOC/TN ratios are controlled by the presence of a non-negligible amount of inorganic nitrogen bound to surface clay mineral particles and/or by microbial processes.
ISSN: 1439-0108

hal-01682110
https://hal.univ-antilles.fr/hal-01682110
DOI : 10.1007/s11368-016-1555-6

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Oisans Massif, located in the external zones of the western Alps, experienced significant shortening during the Alpine collision. While a series of major top-to-the west shear zones was recently described, the general low grade of the metamorphism has not attracted much petrological and geochronological studies. This paper provides combined temperature and age constraints on the evolution of the Oisans Massif. Temperature was estimated with the Raman Spectrometry of Carbonaceous Material (RSCM) method and chlorite geothermometry. Maximum temperature reached by the Mesozoic cover (Tmax) from Grenoble to the Galibier pass (E-W) and from Saint Jean de Maurienne to Embrun (N-S) yielded almost constant ca. 330 °C temperatures all through the Massif. Temperatures however strongly decrease either westward towards the top of the Vercors sedimentary sequence or eastward towards the Penninic Frontal Thrust. Age constraints were retrieved using 40Ar/39Ar in situ analyses performed on variously strained samples from Alpine shear zones. Over strain gradients, incipient Alpine recrystallizations progressively develop at the expense of former Variscan parageneses. A combined textural and EPMA approach permitted to identify newly formed chlorite and phengite that unequivocally grew in response to deformation or to low grade metamorphism. Chlorites recorded temperatures from ca. 350–150 °C during the activity of shear zones. In parallel, 40Ar/39Ar in situ experiments enabled dating deformation using both synkinematic phengites crystallized below the closure temperature of white-micas and former Variscan muscovite whose isotopic system have been, at least partially re-opened. Activity of top-to-the-west shear zones responsible for the shortening and thickening of the Oisans massif thus occurred between 34 and 33 and 25 Ma. Integrating these new age-constraints, Tmax estimates, and published geological data on the Oisans Massif and neighbouring areas allow proposing a new shortening scenario for the external zones. From ca. 34–33 Ma, the Oisans Massif was buried as a rigid block below more internal units and reached a temperature of ca. 330 °C. Shearing progressively localized along a series of top-to-the-W shear zones in the basement until 25 Ma. Deformation then localized along a major thrust at the base of the ECM massif and propagated along the basement-cover interface below the Vercors massif after 16 Ma.
ISSN: 0264-3707

Droits : info:eu-repo/semantics/OpenAccess
insu-01093878
https://hal-insu.archives-ouvertes.fr/insu-01093878
https://hal-insu.archives-ouvertes.fr/insu-01093878/document
https://hal-insu.archives-ouvertes.fr/insu-01093878/file/GEOD1326RA.pdf
DOI : 10.1016/j.jog.2014.09.004

Éditeur(s) : HAL CCSD
Résumé : International audience
The carbon capture and storage is considered as one of the solutions of reducing the effects of global warming. It consists in injecting large quantities of CO 2 in supercritical form directly into deeply located geological formations. One of the methods involves sequestration in the carbonate sedimentary rocks (sandstones and limestones) which are considered as a promising solution. The morphology of the pore network and solid skeleton defines important macroscopic prop-erties of the rock (permeability, stiffness). Modelling at micro scale of random heterogeneous materials (porous media) should be based on morphological and statistical characterisation 1,2 of the investigated microstructure. The work is focused on a reconstruction method by grains deposit 3 , for various range of pa-rameters, to obtain equivalent model of natural rock samples (oolitic limestone and fontainebleau sandstone). Generated samples satisfy morphological and statistical informations 4 which were obtained by 3D image analysis of X-ray tomography of the natural rock samples. For validation of the modelling numerical computations of mechanical and transfer properties are also provided.
14th European Mechanics of Materials Conference - EMMC14
Gothembourg, Sweden

hal-01103163
https://hal.archives-ouvertes.fr/hal-01103163