Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Thermal diffusivity of synthetic quartz single-crystals and natural polycrystalline aggregates were measured using a modified Angstrom method at ambient pressure and up to 800 degrees C in order to investigate the effect of crystal preferred orientation on thermal diffusivity of quartz rich rocks. The thermal diffusivity tensor of quartz was determined by measuring the thermal diffusivity of an oriented synthetic quartz single-crystal along the [100] and [001] directions. A naturally deformed, fine-grained quartzite mylonite, was used to compare the single crystal properties with aggregate properties. Using the crystal preferred orientations (CPO) measured by the Electron Back Scattered Diffraction (EBSD) method and the measured thermal diffusivity tensor of quartz, the three-dimensional aggregate thermal diffusivity was modelled using volume averaging models. In order to test the validity of these models that are only based on the properties of the constituent minerals, the thermal diffusivity was then measured on oriented cores as a function of temperature, along three orthogonal directions, parallel to the (X-lineation, Y, Z-pole to foliation) structural frame. Both modelled and direct measurement of thermal diffusivity show an anisotropy of thermal diffusivity, heat transport being more effective parallel to Y-direction and less effective parallel to the lineation X-direction. Thermal diffusivities measured in a given direction on the natural rock are lower by less than 10% than the modelled thermal diffusivity in the same direction, showing that rock imperfections have a weak effect on heat transport. In addition, the modelled thermal diffusivity anisotropy based on the characterization of crystal orientations and thermal diffusivity tensor shows a good agreement with measurements in both alpha and beta stability field. This validation of the petrophysical simulation allows for evaluating the 3D thermal diffusivity of quartz rich rocks in different crustal conditions. The 3D thermal diffusivity of five naturally deformed quartzites displaying quartz fabrics expected in different crustal pressure and temperature ranges were simulated. The resulting thermal diffusivity anisotropies of quartzites range between 40% and 10%, depending on temperature, crystallographic fabric patterns and fabric strength. Under crustal conditions, quartzites deformed in the granulite facies display a high thermal diffusivity in the (XZ) foliation plane, whereas quartzites deformed in greenschist facies have highest thermal diffusivity in the (Z) direction normal to the foliation plane.
ISSN: 0040-1951

hal-00413568
https://hal.archives-ouvertes.fr/hal-00413568
DOI : 10.1016/j.tecto.2008.11.006

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Seismic tomography and high surface heat flow models indicate an anomalously thin and hot lithospheric mantle beneath the Canadian Cordillera. To understand the thermal and deformational history of the lithospheric mantle under these conditions, we performed a study of the microstructures, crystal preferred orientations (CPO), and seismic anisotropy of mantle xenoliths collected in the Summit Lake volcano in the southern Canadian Cordillera. The xenoliths vary in composition between spinel lherzolites, cpx-rich lherzolites, and wehrlites. All samples are coarse-grained and show clear evidence for annealing, but deformation microstructures are well-preserved in the spinel lherzolites. Olivine CPO is characterized by a strong point-maximum of [100] and by a girdle distribution of [010[ and [001] axes normal to it; CPO strength is variable, spinel-lherzolites have the strongest CPO. Some samples show a weak orthopyroxene CPO consistent with the olivine one. However most pyroxenes have random CPO, interstitial shapes and undeformed appearance, which suggest a secondary origin by reactive melt percolation under static conditions, leading to crystallization of cpx + sp +/- opx at the expenses of olivine, followed by crystallization of cpx + sp +/- ol at the expenses of opx to produce the wehrlites. The studied xenoliths have typical upper mantle seismic properties patterns with fastest propagation of P-waves and polarization of S-waves parallel to the olivine [100] maxima. Maximum P- and S-waves anisotropy for lherzolites are 8 and 5% respectively. Dispersion of the olivine CPO due to neocrystallization of olivine results in weaker anisotropies (6.5 and 3.5%) in wehrlites. Seismic velocities calculated using a geotherm consistent with the equilibrium temperatures of the Summit Lake xenoliths are 3-4% lower than those expected in a normal, 100 km-thick lithosphere, consistent with seismic tomography models for the region. This high geothermal gradient may be partially explained by considering the anisotropy of thermal conductivity of olivine and subhorizontal foliations in the lithospheric mantle, which result in a decrease by up to 15% of the thermal conductivity in the vertical direction.
ISSN: 0040-1951

hal-00618332
https://hal.archives-ouvertes.fr/hal-00618332
DOI : 10.1016/j.tecto.2011.04.014

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This paper examines the thermal properties of cement composites reinforced with vegetable bagasse fibres (1.5% and 3% wrtc). Thermal properties have been correlated to macroscopic density and porosity in order to estimate thermal conductivity of fibres using a calculation inspired from the Maxwell-Eucken modelling. Experimental investigations reveal that adding retified bagasse fibres reduces composites thermal conductivity and yields a weaker specific heat in comparison with composites made with alkaline bagasse fibres. Moreover, the more the fibres, the lighter the specimen; lower its thermal conductivity and lower its specific heat. Thermal conductivity of alkaline fibres is lower than retified fibres one.
ISSN: 1359-835X

hal-00809831
https://hal.univ-antilles.fr/hal-00809831
DOI : 10.1016/j.compositesa.2010.01.002

Éditeur(s) : HAL CCSD European Geosciences Union
Résumé : We designed a thermo-mechanical numerical model for fast-spreading mid-ocean ridge with variable viscosity, hydrothermal cooling, latent heat release, sheeted dyke layer, and variable melt intrusion possibilities. The model allows for modulating several accretion possibilities such as the "gabbro glacier" (G), the "sheeted sills" (S) or the "mixed shallow and MTZ lenses" (M). These three crustal accretion modes have been explored assuming viscosity contrasts of 2 to 3 orders of magnitude between strong and weak phases and various hydrothermal cooling conditions depending on the cracking temperatures value. Mass conservation (stream-function), momentum (vorticity) and temperature equations are solved in 2-D cartesian geometry using 2-D, alternate direction, implicit and semi-implicit finite-difference scheme. In a first step, an Eulerian approach is used solving iteratively the motion and temperature equations until reaching steady states. With this procedure, the temperature patterns and motions that are obtained for the various crustal intrusion modes and hydrothermal cooling hypotheses display significant differences near the mid-ocean ridge axis. In a second step, a Lagrangian approach is used, recording the thermal histories and cooling rates of tracers travelling from the ridge axis to their final emplacements in the crust far from the mid-ocean ridge axis. The results show that the tracer's thermal histories are depending on the temperature patterns and the crustal accretion modes near the mid-ocean ridge axis. The instantaneous cooling rates obtained from these thermal histories betray these discrepancies and might therefore be used to characterize the crustal accretion mode at the ridge axis. These deciphering effects are even more pronounced if we consider the average cooling rates occurring over a prescribed temperature range. Two situations were tested at 1275-1125 °C and 1050-850 °C. The first temperature range covers mainly the crystallization range that is characteristic of the high temperature areas in the model (i.e. the near-mid-oceanic-ridge axis). The second temperature range corresponds to areas in the model where the motion is mainly laminar and the vertical temperature profiles are closer to conductive. Thus, this situation results in less discriminating efficiency among the crustal accretion modes since the thermal and dynamic properties that are described are common to all the crustal accretion modes far from the ridge axis. The results show that numerical modeling of thermo-mechanical properties of the lower crusts may bring useful information to characterize the ridge accretion structure, hydrothermal cooling and thermal state at the fast-spreading ridges and may open discussions with petrological cooling rate results.
ISSN: 1991-959X

hal-00907012
https://hal.archives-ouvertes.fr/hal-00907012
DOI : 10.5194/gmd-6-1659-2013

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
B-type olivine fabrics are pervasive within highly depleted dunites of the small-sized Imono peridotite body located within the subduction-type Sanbagawa metamorphic belt of the southwest Japan arc. The dunites contain various microstructures, ranging from porphyroclastic to fine-grained intensely sheared textures. The Mg/(Mg+Fe) atomic ratios (Fo number) of olivine within these dunites are consistently around 0.9, as are the Cr/(Cr+Al) atomic ratios (Cr number) of chromian spinel, suggesting their evolution from a highly depleted magma (boninite). These data provide strong thermal constraints on the formation of the highly depleted dunites,as their formation requires hot, hydrous, shallow mantle (> 1250 degrees C at < 30 km depth) in the mantle wedge. Because the Sanbagawa metamorphic belt finally entrained these peridotites during progressive retrogression, B-type olivine fabrics probably developed in the fore-arc side of the subduction zone, above or along the subducting slab, possibly in association with dehydration fluids derived from the slab. The previously documented small magnitude of S-wave splitting can be explained by the seismic properties of B-type peridotites within an anisotropic layer of approximately several kilometers in thickness, oriented by flow parallel to the subducting slab, under maximum temperatures of 880-1030 degrees C depending on the flow stress. These findings indicate that such a B-type layer could constitute a dominant source of seismic S- and P-wave anisotropy in mantle wedge regions. (c) 2008 Elsevier B.V. All rights reserved.
ISSN: 0012-821X

hal-00412594
https://hal.archives-ouvertes.fr/hal-00412594
DOI : 10.1016/j.epsl.2008.06.014

Éditeur(s) : HAL CCSD ACS American Chemical Society - Publications
Résumé : International audience
ABSTRACT: In this paper, the structural, optical and thermal properties of n-type (100),p-type (100) and (111) mesoporous silicon (MePSi) are reported. The mesoporous silicon wasprepared by an electrochemical process from bulk silicon wafer. Depending on the etchingdepth, analyses show that the porosity of p-type (111) increased by 32 to 40% compared to p(100) which, in turn, increased by 22 to 48% compared to n-type (100). The structuremorphology and the abundance of Si-Ox and Si-Hy also depended heavily on the type andcrystal orientation of MePSi. The thermal properties of the MePSi layers such as thermalconductivity (κ), volumetric heat capacity (ρCp) and thermal contact resistance (Rth) weredetermined using the pulsed photothermal method. The thermal conductivity of bulk silicondropped sharply after etching, decreasing by more than twenty-fold in the case of n-type (100)and by over forty-five fold for p-type (100) and (111). According to the percolation modeldepending on both porosity and phonon confinement, the drop in thermal conductivity wasmainly due to the nanostructure formation after etching. Thermal investigations showed thatthe volumetric heat capacity (ρCp) followed the barycentric model which depends mainly onthe porosity. The thermal contact resistances of MePSi layers were estimated to be in therange of 1x10-8 to 1x10-7 K⋅m2⋅W-1.
The Journal of Physical Chemistry C

hal-01495490
https://hal.archives-ouvertes.fr/hal-01495490
DOI : 10.1021/acs.jpcc.6b13101

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Numerical models show that small-scale convection (SSC) occurring atop a mantle plume is a plausible mechanism to rejuvenate the lithosphere. The triggering of SSC depends on the density contrast and on the rheology of the unstable layer underlying the stagnant upper part of the thermal boundary layer (TBL). Partial melting may change both properties. We analyze, using 2-D numerical simulations, how partial melting influences the dynamics of time-dependent SSC instabilities and the resulting thermo-mechanical rejuvenation of an oceanic plate moving atop of a plume. Our simulations show a complex behavior, with acceleration, no change, or delay of the SSC onset, due to competing effects of the latent heat of partial melting, which cools the plume material, and of the buoyancy increase associated with both melt retention and depletion of residue following melt extraction. The melt-induced viscosity reduction is too localized to affect significantly SSC dynamics. Faster SSC triggering is promoted for low melting degrees (low plume temperature anomalies, thick lithosphere, or fast moving plates), which limit both the temperature reduction due to latent heat of melting and the accumulation of depleted buoyant residue in the upper part of the unstable layer. In contrast, high partial melting degrees lead to a strong temperate decrease due to latent heat of melting and development of a thick depleted layer within the sublithospheric convecting layer, which delay the development of gravitational instabilities. Despite differences in SSC dynamics, the thinning of the lithosphere is not significantly enhanced relatively to simulations that neglect partial melting.
ISSN: 1525-2027

hal-01277175
https://hal.archives-ouvertes.fr/hal-01277175
DOI : 10.1002/2015GC005967

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
This paper aims to present an overview on the influence of rheological heterogeneity and mechanical anisotropy on the deformation of continents. After briefly recapping the concept of rheological stratification of the lithosphere, we discuss two specific issues: (1) as supported by a growing body of geophysical and geological observations, crust=mantle mechanical coupling is usually efficient, especially beneath major transcurrent faults which probably crosscut the lithosphere and root within the sublithospheric mantle; and (2) in most geodynamic environments, mechanical properties of the mantle govern the tectonic behaviour of the lithosphere. Lateral rheological heterogeneity of the continental lithosphere may result from various sources, with variations in geothermal gradient being the principal one. The oldest domains of continents, the cratonic nuclei, are characterized by a relatively cold, thick, and consequently stiff lithosphere. On the other hand, rifting may also modify the thermal structure of the lithosphere. Depending on the relative stretching of the crust and upper mantle, a stiff or a weak heterogeneity may develop. Observations from rift domains suggest that rifting usually results in a larger thinning of the lithospheric mantle than of the crust, and therefore tends to generate a weak heterogeneity. Numerical models show that during continental collision, the presence of both stiff and weak rheological heterogeneities significantly influences the large-scale deformation of the continental lithosphere. They especially favour the development of lithospheric-scale strike-slip faults, which allow strain to be transferred between the heterogeneities. An heterogeneous strain partition occurs: cratons largely escape deformation, and strain tends to localize within or at the boundary of the rift basins provided compressional deformation starts before the thermal heterogeneity induced by rifting are compensated. Seismic and electrical conductivity anisotropies consistently point towards the existence of a coherent fabric in the lithospheric mantle beneath continental domains. Analysis of naturally deformed peridotites, experimental deformations and numerical simulations suggest that this fabric is developed during orogenic events and subsequently frozen in the lithospheric mantle. Because the mechanical properties of single-crystal olivine are anisotropic, i.e. dependent on the orientation of the applied forces relative to the dominant slip systems, a pervasive fabric frozen in the mantle may induce a significant mechanical anisotropy of the whole lithospheric mantle. It is suggested that this mechanical anisotropy is the source of the so-called tectonic inheritance, i.e. the systematic reactivation of ancient tectonic directions; it may especially explain preferential rift propagation and continental break-up along pre-existing orogenic belts. Thus, the deformation of continents during orogenic events results from a trade-off between tectonic forces applied at plate boundaries, plate geometry, and the intrinsic properties (rheological heterogeneity and mechanical anisotropy) of the continental plates.
ISSN: 0040-1951

hal-01389719
http://hal.univ-reunion.fr/hal-01389719
http://hal.univ-reunion.fr/hal-01389719/document
http://hal.univ-reunion.fr/hal-01389719/file/vauchez_etal_rheology_1998_hal.pdf
DOI : 10.1016/S0040-1951(98)00137-1

Éditeur(s) : HAL CCSD Geological society of London
Résumé : International audience
We present a synthesis of the tectonic and thermochronological evolution of the Eastern Tibet since the Triassic. The long-term cooling histories obtained on magmatic and metamorphic rocks of the South Songpan-Garze--, Kunlun and Yidun blocks are similar showing a very slow and regular cooling during Late Jurassic and Cretaceous, confirming the suspected lack of major tectonic events between c. 150 and 30 Ma. The exhumation linked to the Tertiary growth of the Tibetan Plateau initiated around 30 Ma and concentrates at the vicinity of the major tectonic structures. Exhumation rates increased again from about 7 Ma in the Longmen Shan. To interpret this very slow cooling rate between Late Jurassic and Early Cenozoic from granites of this area, we use a simple 1D thermal model that takes into account the thermal properties of both sediments and crust. The results suggest that: (1) high temperature (500 8C) can be kept over a long period of time; (2) during Cretaceous, cooling is mostly controlled by the thermal properties of sediments of continental origin; and (3) the initial Late Triassic rapid cooling rate was caused by the large thermal contrast between the granite body and the sedimentary rocks rather than by a high exhumation rate.
Growth and Collapse of the Tibetan Plateau

insu-00610491
https://hal-insu.archives-ouvertes.fr/insu-00610491
DOI : 10.1144/SP353.2

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The lithospheric mantle is intrinsically heterogeneous and anisotropic. These two properties govern the repartition of deformation, controlling intraplate strain localization and development of new plate boundaries. Geophysical and geological observations provide clues on the types, ranges, and characteristic length scales of heterogeneity and anisotropy in the lithospheric mantle. Seismic tomography points to variations in geothermal gradient and hence in rheological behavior at scales of hundreds of km. Seismic anisotropy data substantiate anisotropic physical properties consistent at scales of tens to hundreds of km. Receiver functions imply lateral and vertical heterogeneity at scales < 10 km, which might record gradients in composition or anisotropy. Observations on naturally deformed peridotites establish that compositional heterogeneity and Crystal Preferred Orientations (CPOs) are ubiquitous from the mm to the km scales. These data allow discussing the processes that produce/destroy heterogeneity and anisotropy and constraining the time scales over which they are active. This analysis highlights: (i) the role of deformation and reactive percolation of melts and fluids in producing compositional and structural heterogeneity and the feedbacks between these processes, (ii) the weak mechanical effect of mineralogical variations, and (iii) the low volumes of fine-grained microstructures and difficulty to preserve them. In contrast, olivine CPO and the resulting anisotropy of mechanical and thermal properties are only modified by deformation. Based on this analysis, we propose that strain localization at the plate scale is, at first order, controlled by large-scale variations in thermal structure and in CPO-induced anisotropy. In cold parts of the lithospheric mantle , grain size reduction may contribute to strain localization, but the low volume of fine-grained domains limits this effect.
ISSN: 0040-1951

hal-01277174
https://hal.archives-ouvertes.fr/hal-01277174
DOI : 10.1016/j.tecto.2015.07.026

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Polarized emittance measurements were acquired for synthetic forsterite, the pure magnesium end member of the olivines group, on the whole infrared spectral range and up to the melting point by using CO2 laser heating. The experimental data, fitted with a semi-quantum dielectric function model, allowed the retrieval of the temperature dependence of the absorption coefficient of forsterite both in the opaque and semi-transparent regions. The analysis of the phonon parameters indicates that the lattice dynamics evolve drastically with increasing temperature. The normal modes involving motions of the magnesium cations located in site 1 are the more impacted, and some of them vanish around 1,200 K. The results confirm that the enhancement of the lattice anharmonicity and the increasing mobility of the magnesium cations are closely linked and are at the origin of the anomalies observed in the evolution of the thermophysical properties. This complete set of spectroscopic data may be a step toward a more precise evaluation of the impact of thermal radiation heat transfer inside systems involving forsterite and quantification of their heat budget.
ISSN: 0342-1791

hal-00817079
https://hal.archives-ouvertes.fr/hal-00817079
DOI : 10.1007/s00269-013-0570-z

Résumé : L’incorporation de sous-produits agricoles ou de matériaux naturels dans la matrice cimentaire confère des propriétés intéressantes aux composites élaborés. L’objectif de cette thèse est d’élaborer un matériau pouvant répondre aux exigences mécaniques, thermiques et de durabilité des matériaux de construction en zone tropicale humide. Dans un premier temps, l’activité pouzzolanique d’une pouzzolane naturelle, de cendres de tronc de bambou et de cendres de bagasse de canne à sucre ont été évaluées. L’influence de leur incorporation a été ensuite étudiée sur les propriétés mécaniques et la durabilité des mortiers exposés à des ions chlorures et sulfates. Dans un second temps, l’influence de l’ajout de fibres de bagasse sur les propriétés thermiques et mécaniques des composites a été étudiée en fonction de différents paramètres (teneur en fibres, environnement de vieillissement, type de matrice cimentaire).Les résultats obtenus ont permis de montrer que les matériaux étudiés possèdent une activité pouzzolanique et qu’il est possible de les incorporer au ciment afin de lutter contre la corrosion. De plus, les composites élaborés avec des fibres de bagasse sont plus isolants que ceux élaborés sans fibres. Cependant, du point de vue des propriétés mécaniques, l’incorporation de fibres de bagasse diminue les contraintes à la flexion des composites.
The incorporation of crop wastes or natural materials in the cement matrix confers interesting properties to composites prepared. The aim of this thesis is to develop a material that can reach the mechanical, thermal and durability requirements for building materials in the humid tropical zone. Firstly, pozzolanic activity of a natural pozzolan, bamboo stem and sugar cane bagasse ashes has been determined. Influence of their incorporation on mechanical properties and durability of mortars exposed to chloride and sulphate ions was studied. Secondly, influence of addition of bagasse fibers on thermal and mechanical properties of composites was studied as a function of various parameters (fibers content, curing, type of cement matrix).These results has shown that the materials studied have pozzolanic activity and it is possible to incorporate them into the cement to fight against corrosion. Moreover, composites elaborated with bagasse fibers are more insulating than those elaborated without fibers. However, from the viewpoint of mechanical properties, incorporation of bagasse fibers decreases flexural strength of composites in the present work and under the conditions producing procedures that were adopted.

http://www.theses.fr/2014AGUY0804/document

Éditeur(s) : HAL CCSD
Résumé : 38 pages
Rapport
The Chicxulub impact crater, México, is unique. It is the only known terrestrial impact structure that has been directly linked to a mass extinction event and the only terrestrial impact with a global ejecta layer. Of the three largest impact structures on Earth, Chicxulub is the best preserved. Chicxulub is also the only known terrestrial impact structure with an intact, unequivocal topographic peak ring. Chicxulub’s role in the Cretaceous/Paleogene (K-Pg) mass extinction and its exceptional state of preservation make it an important natural laboratory for the study of both large impact crater formation on Earth and other planets and the effects of large impacts on the Earth’s environment and ecology. Our understanding of the impact process is far from complete, and despite more than 30 years of intense debate, we are still striving to answer the question as to why this impact was so catastrophic.During International Ocean Discovery Program (IODP) Expedition 364, Paleogene sediments and lithologies that make up the Chicxulub peak ring were cored to investigate (1) the nature and formational mechanism of peak rings, (2) how rocks are weakened during large impacts, (3) the nature and extent of post-impact hydrothermal circulation, (4) the deep biosphere and habitability of the peak ring, and (5) the recovery of life in a sterile zone. Other key targets included sampling the transition through a rare midlatitude section that might include Eocene and Paleocene hyperthermals and/or the Paleocene/Eocene Thermal Maximum (PETM); the composition and character of the impact breccias, melt rocks, and peak-ring rocks; the sedimentology and stratigraphy of the Paleocene–Eocene Chicxulub impact basin infill; the chronology of the peak-ring rocks; and any observations from the core that may help us constrain the volume of dust and climatically active gases released into the stratosphere by this impact. Petrophysical property measurements on the core and wireline logs acquired during Expedition 364 will be used to calibrate geophysical models, including seismic reflection and potential field data, and the integration of all the data will calibrate impact crater models for crater formation and environmental effects. The proposed drilling directly contributes to IODP Science Plan goals:Climate and Ocean Change: How resilient is the ocean to chemical perturbations? The Chicxulub impact represents an external forcing event that caused a 75% level mass extinction. The impact basin may also record key hyperthermals within the Paleogene.Biosphere Frontiers: What are the origin, composition, and global significance of subseafloor communities? What are the limits of life in the subseafloor? How sensitive are ecosystems and biodiversity to environmental change? Impact craters can create habitats for subsurface life, and Chicxulub may provide information on potential habitats for life, including extremophiles, on the early Earth and other planetary bodies. Paleontological and geochemical studies at ground zero will document how large impacts affect ecosystems and effects on biodiversity.Earth Connections/Earth in Motion: What are the composition, structure and dynamics of Earth’s upper mantle? What mechanisms control the occurrence of destructive earthquakes, landslides, and tsunami? Mantle uplift in response to impacts provides insight into dynamics that differ between Earth and other rocky planets. Impacts generate earthquakes, landslides, and tsunami, and scales that generally exceed plate tectonic processes yield insight into effects, the geologic record, and potential hazards.IODP Expedition 364 was a Mission Specific Platform expedition to obtain subseabed samples and downhole logging measurements from the sedimentary cover sequence and peak ring of the Chicxulub impact crater. A single borehole was drilled into the Chicxulub impact crater on the Yucatán continental shelf, recovering core from 505.7 to 1334.73 m below seafloor with ~99% core recovery and acquiring downhole logs for the entire depth.
International Ocean Discovery Program

hal-01639520
https://hal.archives-ouvertes.fr/hal-01639520
DOI : 10.14379/iodp.pr.364.2017

Éditeur(s) : HAL CCSD
Résumé : Composite materials incorporating vegetable fibres have known an increasingly interest during the past few decades. These environmental friendly materials are low-cost and offer advantages such as reduction of electrical consumption by air conditioning. Moreover, the use of vegetable fibres in replacement of synthetic fibre is interesting in developing countries where the availability of tropical plants and agricultural waste is important. This paper presents an initial investigation on the use of a construction material, composed of cement and pre-treated (heat or alkaline treatments) sugar cane bagasse fibres. The purpose of this study is to analyse the effect of fibre content and treatment on thermal conductivity, specific heat, flexural strength and density. The addition of retified fibres reduces composites thermal conductivity and yields a weaker specific heat in comparison with composites made with alkaline fibres. From mechanical point of view, composites made with alkaline fibres have a better flexural strength than others.
12th International Inorganic-bonded Fiber Composites Conference
Aalborg, Denmark

hal-00807543
https://hal.univ-antilles.fr/hal-00807543

Éditeur(s) : HAL CCSD Springer/Terra Scientific Publishing Company
Résumé : International audience
The laboratory of paleomagnetism of Montpellier (France) has developed a new one-axis vibrating thermal magnetometer dedicated to the Study of physical properties of natural rocks remanence. Among its key characteristics, this apparatus allows both measurement or the magnetization moment on the interval from room temperature to 700 degrees C with a precision of 2 x 10(-9) A m(2) and acquisition of a total or a partial thermo-remanent magnetization using a steady field from - 100 up to 100 mu T. Another point that is worth noting is that one can apply a controlled atmosphere by means of argon flux to prevent oxidation of the studied sample during heating. We report here a technical description of this new instrument and review some specific applications in absolute paleointensity surveys.
ISSN: 1343-8832

hal-00413078
https://hal.archives-ouvertes.fr/hal-00413078
https://hal.archives-ouvertes.fr/hal-00413078/document
https://hal.archives-ouvertes.fr/hal-00413078/file/Poidras-CatVTM.pdf

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
Reaction wood produces very peculiar maturation stresses at the tree periphery i.e. compressive stress or very high tensile stress, for compression and tension wood respectively, as compared to moderately high tensile stress for normal wood. This means that both its mechanical state and its mechanical and physical properties differ from normal wood. Compression wood shows big differences from normal wood in conifers, for all physical and mechanical properties: higher density and axial crushing strength (MOR) but lower modulus of elasticity (MOE), far higher axial (longitudinal) shrinkage but lower radial and tangential shrinkage, sometimes even lower than the axial shrinkage. For tension wood things are less simple and can vary a lot from hardwood species to species. Globally there are no systematic differences in density and transverse shrinkage, MOE tends to be a little higher while MOR is slightly lower. However, axial shrinkage is much higher for tension wood with a gelatinous layer (G layer) than normal wood due to the specific gel like organization of cellulose microfibrils in the G layer. For tension wood without a G layer(which is rather frequent) axial shrinkage in the first drying operation is around two times higher than in normal wood mainly because of a kind of hygro-thermal release of locked in maturation stress. Overall the very high tensile stress and stored elastic energy in tension wood lead to problemsin wood processing (end splitting and board warping), which is far less the case for compression wood. But due to the large difference in properties relative to normal wood, compression wood occurrence is always a big problem for the in service behaviour of timber, which is seldom the case for tension wood.
The biology of reaction wood

ISBN : 978-3-642-10813-6
hal-01135273
https://hal.archives-ouvertes.fr/hal-01135273

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : We present a detailed rock-magnetic and archaeomagnetic study of two brick kilns, named OSA and OSB, discovered at the location of Osterietta, in northern Italy. The magnetic properties of representative samples have been investigated to identify the nature of the magnetic carriers, their domain state and thermal stability, and investigate their suitability for archaeomagnetic determinations. Thermally stable, mainly pseudosingle domain (PSD) magnetite is identified as the main magnetic carrier. The full geomagnetic field vector has been determined for the two kilns, including directional and intensity analysis. Archaeointensities have been recovered with both the classical Thellier and the multi-specimen protocols. The multi-specimen procedure was performed with a very fast-heating oven developed at Montpellier, France. A Matlab® code for anisotropy correction during the Thellier experiment is provided. The archaeointensity results obtained from both techniques for the OSA kiln are of high quality and in good mutual agreement. For the OSB kiln, Thellier results are characterized by large standard deviation and the multi-specimen (MSP) technique was not successful. The obtained full geomagnetic field vector (declination, inclination and intensity) has been used for the archaeomagnetic dating of the two structures suggesting that the OSA kiln was for the last time used between 1761?1841 A.D. and the OSB kiln between 1752?1831 A.D., at 95% probability. This study shows that intensity determinations do not restrict the dating results when referring to the last few centuries, as this period is characterized by very small intensity variations.
ISSN: 0039-3169

hal-01236052
https://hal.archives-ouvertes.fr/hal-01236052
DOI : 10.1007/s11200-015-0413-0

Éditeur(s) : HAL CCSD
Résumé : We present an experimental study of relations between hydraulic properties of clayey rocks and their deformation at bulk and micro scale. The experimentation is based on triaxial deformation of kaolinitic core samples, on permeability measurements, and on several methods of analysis of the microstructure. To produce the samples, remoulded kaolinite material is consolidated by axial loading up to 20 MPa in an oedometric cell. Then, in a triaxial cell, an undrained stress path is applied in order to induce shearing damage in the sample. The permeability of the sample is measured by fluid flow across the sample. Before and after these hydro-mechanical tests, the evolution and the homogeneity of the pore space and moreover the texture of the material are analysed by X-ray tomography, environmental scanning electron microscopy and thermic neutron diffraction. Contrary to expectations, the permeability at the sample scale does not vary significantly, although quite large deformation is reached. The final deformation is heterogeneous, with well-developed shear bands. It appears that the development of compacting and dilating zones generates a heterogeneous permeability field, which results in a negligible variation of the bulk permeability at the sample scale.
International Journal of Rock Mechanics and Mining Science

hal-00496407
https://hal.archives-ouvertes.fr/hal-00496407
DOI : 10.1016/j.ijrmms.2010.04.007

Éditeur(s) : HAL CCSD
Résumé : International audience
The purpose of our study is to model a geothermal reservoir. When geothermal reservoir are assumed to be composed of pure water, the transfer of mass and energy is classically described by two balance equations: mass balance equation and the energy balance equation. In addition to those equations, fluid velocity ist classically given by the Darcy law while thermodynamic properties, inferred from theoretical or empirical equations of state, are used to close the mathematical system. Once this system is closed, there exist different solutions. The first one is to solve for pressure and temperature with a variable switch to saturation in the two-phase region (e.g. TOUGH2). The second one is to solve for pressure and enthalpy to increase stability of phase transition between single and two-phase states (e.g. Hydrotherm). We adopted the second option and chose te use a splitting method to get rid of the complexity of coupling equations and a finite volume method for the spatial discretization. Selecting object-oriented languages, we developed a multi-language framework, combining Python, Fortran and a C++ implementation of IAPWS (from the freesteam project) including the supercritical equations, in porous media velocity is given by Darcy law and to close the system physical properties are determined by the IAPWS-IF97 thermodynamic formulation. We resolve the equations in pressure and enthalpy instead of pressure and temperature in order to increase stability and to handle easier the passage from a single-phase to a two-phase system. We solve the system by using a splitting method - to get rid of the complexity of coupling equations - and a finite volume method. We offer some freedom to users thanks to the implementation of several methods like explicit or implicit Euler, Runge-Kutta or BDF2 for time solvers or GMRES and BICGSTAB for the linear solver. We can handle several boundary conditions like no-flow - describing a boundary which can not exchange matter with the exterior - or like a mixed-therm condition - a Dirichlet condition to the pressure and a Dirichlet or an outflow condition to the temperature in order to describe a recharge or a discharge zone - ... We're developing a multi-language framework, combining Python, Fortran and the C++ implementation of IAPWS (from the freesteam project). All these languages are object-oriented. We've applied this simulation model to the dogger in Paris, France, to several one-dimensional systems and a two-dimensional one made by Coumou with the CSMP++ platform. The dogger is a reservoir exploited to produce heat by pumping water at 70 and reinjecting it in the reservoir at 40. In the one-dimensional systems we wanted to observe the process of heat transfer from a higher temperature boundary to a smaller one in a high-energy domain. The last simulation shows the natural convection of water in a fault. For every simulation we compared the solutions we found with an other code (TOUGH2 or CSMP++) and they agreed. The next step will be to model the geothermal plant in Guadeloupe, West Indies. It's the only place in France - and in the West Indies so far - producing electricity with the earth power. The temperature can reach up to 1000 and the pressure range is around a few hundreds MPa. In some surface zones we can see two-phase water at atmospheric pressure. In the 1980s Bouillante was a laboratory for France. Since 1995 Bouillante has given 30GWh electricity a year to the Guadeloupeans.
PROCEEDINGS, Thirty-Ninth Workshop on Geothermal Reservoir Engineering
Stanford, United States

Droits : info:eu-repo/semantics/OpenAccess
hal-00944133
https://hal-brgm.archives-ouvertes.fr/hal-00944133
https://hal-brgm.archives-ouvertes.fr/hal-00944133/document
https://hal-brgm.archives-ouvertes.fr/hal-00944133/file/Copol.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Anisotropy of low-field magnetic susceptibility (AMS) of basaltic lava flows can give some clues about post-emplacement tilting occurring in volcanic sequences. Such a study has been carried out on a sequence of 19 successive lava flows from Kerguelen Archipelago. Surprisingly, two different patterns were observed. The first one - herein called normal fabric - is consistent with the lava-flow direction inferred from geological observations, whereas the second one observed for about 70 per cent of the analysed samples - herein called abnormal fabric - appears to be unrelated to the shear history of the lava flows during their emplacements. These abnormal fabrics are not strictly inverse fabric but seem to have a more complex origin. The unusual nature of these abnormal fabrics has been confirmed by lattice preferred orientation of plagioclases obtained from high-resolution electron backscattered diffraction measurements. The aim of this study is to propose a physical interpretation of these fabrics. A first step in our understanding was to clearly identify the nature and the magnetic properties of the Fe-Ti oxides assemblage. Thus, we present a comprehensive rock magnetic analysis relying on low- and high-temperature thermomagnetic curves (K-T), crossover diagrams, first-order reversal curves, ore-microscopy, Mössbauer measurements and electron backscattered images. We found that in the present case the abnormal fabrics are probably linked to a mixture of prevailing single domain (SD) strongly interacting grains population and a subsidiary multidomain grains population. SD grains are identified as small magnetite crystallized within the interstitial glass in globular aggregates along the silicate framework. Then a question arises: to what extent such SD interacting grains in globular aggregates can affect the magnetic susceptibility and its anisotropy? To answer this question, we developed a physical model in which the total energy density of an SD grain with an uniaxial anisotropy is minimized. In this model, the distribution function of the direction of the magnetic interaction field is comprised between two boundary states. It is either isotropic, which formally corresponds to the thermal demagnetized state, or it is ordered, which formally corresponds to the Alternative Field demagnetized state. We show that in both cases the degree of anisotropy decreases as the interaction field increases. Thus, we conclude that the abnormal fabric encountered in this study can be simply explained by strong magnetostatic interactions that would explain the large scattering of AMS often observed in basaltic lava flows.
ISSN: 0956-540X

hal-00716449
https://hal.archives-ouvertes.fr/hal-00716449
https://hal.archives-ouvertes.fr/hal-00716449/document
https://hal.archives-ouvertes.fr/hal-00716449/file/gji-S-12-HAL.pdf
DOI : 10.1111/J.1365-246X.2012.05421.X