Éditeur(s) : HAL CCSD
Résumé : International audience
The injection of reactive mineral suspensions is a possible process to either reinforce or seal wells in geologic carbon sequestration sites. Among others, olivine slurries could be used as CO2-triggered cements, as they carbonate under the thermodynamic conditions of deep storage. However, injection of such slurries requires to control their initial fluidity and its evolution during the displacement. For this purpose, we have characterized the rheological evolution of olivine suspensions, of particle sizes 1−10 μm, sheared at 100 s−1, in the ranges of 10−40% for the volume fractions, 20−50 bars for the CO2 pressure, and 60-110°C for the temperature. The apparent viscosity, measured at 100 s−1, increases exponentially, with a characteristic time ranging from less than 1 h to more than 10 h, and decreasing with olivine concentration, CO2 pressure, and temperature. Moreover, a careful characterization of the slurry rheology carried out in the initial stages of slow evolution, shows that the slurry obeys a Bingham plastic law, with a yield stress ΣB, and a Bingham viscosity µB increasing from 1 to 20 Pa and from 4 to 110 mPa s, respectively, when the olivine volume fraction φ is increased from 10 to 30%. Such variations can be accounted by classical models (Wildemuth and Williams [1984]: Rheologica Acta, 23,627-635, Krieger [1972]: Advances in Colloid and Interface Science, 3, 111-136).
Environmental Progress & Sustainable Energy

hal-01054131
https://hal.archives-ouvertes.fr/hal-01054131
DOI : 10.1002/ep.11826

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Brecciated and fractured peridotites with a carbonate matrix, referred to as ophicalcites, are common features of mantle rocks exhumed in passive margins and mid-oceanic ridges. Ophicalcites have been found in close association with massive peridotites, which form the numerous ultramafic bodies scattered along the North Pyrenean Zone (NPZ), on the northern flank of the Pyrenean belt. We present the first field, textural and stable isotopic characterization of these rocks. Our observations show that Pyrenean ophicalcites belong to three main types: (1) a wide variety of breccias composed of sorted or unsorted millimeter- to meter-sized clasts of fresh or oxidized ultramafic material, in a fine-grained calcitic matrix; (2) calcitic veins penetrating into fractured serpentine and fresh peridotite; and (3) pervasive substitution of serpentine minerals by calcite. Stable isotopic analyses (O, C) have been conducted on the carbonate matrix, veins and clasts of samples from 12 Pyrenean ultramafic bodies. We show that the Pyrenean ophicalcites are the product of three distinct genetic processes: (1) pervasive ophicalcite resulting from relatively deep and hot hydrothermal activity; (2) ophicalcites in veins resulting from tectonic fracturing and cooler hydrothermal activity; and (3) polymictic breccias resulting from sedimentary processes occurring after the exposure of subcontinental mantle as portions of the floor of basins which opened during the mid-Cretaceous. We highlight a major difference between the eastern and western Pyrenean ophicalcites belonging, respectively, to the sedimentary and to the hydrothermal types. Our data set points to a possible origin of the sedimentary ophicalcites in continental endorheic basins, but a post-depositional evolution by circulation of metamorphic fluids or an origin from relatively warm marine waters cannot be ruled out. Finally, we discuss the significance of such discrepancy in the characteristics of the NPZ ophicalcites in the frame of the variable exhumation history of the peridotites all along the Pyrenean realm.
ISSN: 1437-3254

insu-00944405
https://hal-insu.archives-ouvertes.fr/insu-00944405
https://hal-insu.archives-ouvertes.fr/insu-00944405/document
https://hal-insu.archives-ouvertes.fr/insu-00944405/file/clerc-etal-IJES-Review.pdf
DOI : 10.1007/s00531-013-0927-z

Éditeur(s) : HAL CCSD Société Géologique de France
Résumé : Xenoliths brought up by kimberlite magmas are rare samples of otherwise inaccessible lithospheric mantle. Eclogite xenoliths are found in most cratons and commonly show a range of mineral and chemical compositions that can be used to better understand craton formation. This study focuses on five new kyanite-bearing eclogites from the Udachnaya kimberlite pipe (367±5 Ma). They are fine-to coarse-grained and consist mainly of “cloudy” clinopyroxene (cpx) and garnet (grt). The clinopyroxene is Al,Na-rich omphacite while the garnet is Ca-rich, by contrast to typical bi-mineral (cpx+grt) eclogites that contain Fe- and Mg-rich garnets. The Udachnaya kyanite eclogites are similar in modal and major element composition to those from other cratons (Dharwar, Kaapvaal, Slave, West African). The kyanite eclogites have lower REE concentrations than bi-mineral eclogites and typically contain omphacites with positive Eu and Sr anomalies, i.e. a “ghost plagioclase signature”. Because such a signature can only be preserved in nonmetasomatised samples, we infer that they were present in the protoliths of the eclogites. It follows that subducted oceanic crust is present at the base of the Siberian craton. Similar compositions and textures are also seen in kyanite eclogites from other cratons, which we view as evidence for an Archean, subduction-like formation mechanism related to craton accretion. Thus, contrary to previous work that classifies all kyanite eclogites as type I (IK), metasomatized by carbonatite/kimberlitic fluids, we argue that some of them, both from this work and those from other cratons, belong to the non-metasomatized type II (IIB). The pristine type IIB is the nearest in composition to protoliths of mantle eclogites because it contains no metasomatic enrichments.
ISSN: 0037-9409

hal-01622617
https://hal.archives-ouvertes.fr/hal-01622617
DOI : 10.1051/bsgf/2017008

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Slices of polycyclic metasediments (marbles and meta-cherts) are tectonically amalgamated with the polydeformed basement of the Dent Blanche tectonic system along a major Alpine shear zone in the Western Alps (Becca di Salé area, Valtournenche Valley). A combination of techniques (structural analysis at various scales, metamorphic petrology, geochronology and trace element geochemistry) was applied to determine the age and composition of accessory phases (titanite, allanite and zircon) and their relation to major minerals. The results are used to reconstruct the polyphase structural and metamorphic histories, comprising both pre-Alpine and Alpine cycles. The pre-Alpine evolution is associated with low-pressure high-temperature metamorphism related to Permo-Triassic lithospheric thinning. In meta-cherts, microtextural relations indicate coeval growth of allanite and garnet during this stage, at ~ 300 Ma. Textures of zircon also indicate crystallisation at HT conditions; ages scatter from 263 to 294 Ma, with a major cluster of data at ~ 276 Ma. In impure marble, U-Pb analyses of titanite domains (with variable Al and F contents) yield apparent 206Pb/238U dates range from Permian to Jurassic. Chemical and isotopic data suggest that titanite formed at Permian times and was then affected by (extension-related?) fluid circulation during the Triassic and Jurassic, which redistributed major elements (Al and F) and partially opened the U-Pb system. The Alpine cycle lead to early blueschist facies assemblages, which were partly overprinted under greenschist facies conditions. The strong Alpine compressional overprint disrupted the pre-Alpine structural imprint and/or reactivated earlier structures. The pre-Alpine metamorphic record, preserved in these slices of metasediments, reflects the onset of the Permo-Triassic lithospheric extension to Jurassic rifting.
ISSN: 0024-4937

hal-00758123
https://hal.archives-ouvertes.fr/hal-00758123
DOI : 10.1016/j.lithos.2012.05.007

Éditeur(s) : HAL CCSD
Résumé : Given the technological development of embedded satellite sensors, the potential of available satellite images increases so that the question now arises of their most efficient exploitation possible. This is the purpose of the CARTAM-SAT project to fluidize the processing workflow from satellite images to users. The thesis is part of this framework.Processing operations relating to images have evolved over the years. Low-resolution images were processed by a so-called pixel approach while the high-resolution has allowed the development of a so-called object approach. The latter focuses on analysing not about the isolated pixels, but about groups of pixels representative of concrete objects on the ground. Thus, in principle, these are groups of pixels with a domain-specific remote sensing semantics.Along with satellite imagery, knowledge representation has evolved. The standards of representation have benefited from the expansion of the web to give rise to standards like OWL. This one is widely based on description logics that allow the use of automated reasoners able to infer implicit knowledge.This thesis is at the junction of these two sciences and provides an ontological approach for analysing satellite images. The aim is to formalize different types of knowledges and conceptualizations implicitly used by image processing programs and by remote sensing experts, and then reasoning automatically on an image description to obtain one semantic interpretation.This general principle may have numerous technical variations. The implementation consisted in a prototype combining a satellite image analysis library and an ontology-based reasoner. The implementation proposed in the thesis allows to explore four technical variations of the principle that lead to discussions on the complementarity of pixel and object analysis paradigms, the representation of some of the spatial relations and the role of knowledge in relation to processing.
Étant donnée l'évolution technologique des capteurs embarqués à bord des satellites, le potentiel d'images satellitaires accessible s'accroît de telle manière que se pose maintenant la question de son exploitation la plus efficace possible. C'est l'objectif du projet CARTAM-SAT que de fluidifier la chaîne de traitement depuis les satellites jusqu'aux utilisateurs des images. La thèse s'inscrit dans ce cadre. Les traitements relatifs aux images ont évolué au cours des années. Les images basse résolution étaient traitées par une approche dite pixel alors que la haute résolution a permis le développement d'une approche dite objet. Cette dernière s'attache à analyser non plus des pixels isolés, mais des groupes de pixels représentatifs d'objets concrets sur le terrain. Ainsi, en principe, ces groupes de pixels sont dotés d'une sémantique propre au domaine de la télédétection. La représentation des connaissances a évolué parallèlement aux images satellitaires. Les standards de représentation ont profité de l'expansion du web pour donner naissance à des standards comme OWL. Celui-ci repose en grande partie sur les logiques de description qui permettent l'utilisation de raisonneurs automatiques capables d'inférer une connaissance implicite.Cette thèse se place à la jonction de ces deux sciences et propose une approche ontologique d'analyse des images satellitaires. Il s'agit de formaliser différents types de connaissances et de conceptualisations implicitement utilisés par les logiciels de traitement d'image et par les experts en télédétection, puis de raisonner automatiquement sur la description d'une image pour en obtenir une interprétation sémantique.Ce principe général est susceptible de nombreuses déclinaisons techniques. La mise en œuvre a consisté en la réalisation d'un prototype alliant une bibliothèque d'analyse d'images satellitaires et un raisonneur basé sur les ontologies. L'implémentation proposée dans la thèse permet d'explorer quatre déclinaisons techniques du principe qui mènent à des discussions sur la complémentarité des paradigmes d'analyse pixel et objet, la représentation de certaines relations spatiales et la place de la connaissance par rapport aux traitements.
https://tel.archives-ouvertes.fr/tel-00998692

NNT : 2013MON20059
tel-00998692
https://tel.archives-ouvertes.fr/tel-00998692
https://tel.archives-ouvertes.fr/tel-00998692/document

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Subduction infancy corresponds to the first few million years following subduction initiation, when slabs start their descent into the mantle. It coincides with the transient (yet systematic) transfer of material from the top of the slab to the upper plate, as witnessed by metamorphic soles welded beneath obducted ophiolites. Combining structure–lithology–pressure–temperature–time data from metamorphic soles with flow laws derived from experimental rock mechanics, this study highlights two main successive rheological switches across the subduction interface (mantle wedge vs. basalts, then mantle wedge vs. sediments; at ∼800 °C and ∼600 °C, respectively), during which interplate mechanical coupling is maximized by the existence of transiently similar rheologies across the plate contact. We propose that these rheological switches hinder slab penetration and are responsible for slicing the top of the slab and welding crustal pieces (high- then low-temperature metamorphic soles) to the base of the mantle wedge during subduction infancy. This mechanism has implications for the rheological properties of the crust and mantle (and for transient episodes of accretion/exhumation of HP-LT rocks in mature subduction systems) and highlights the role of fluids in enabling subduction to overcome the early resistance to slab penetration.
ISSN: 0012-821X

hal-01383368
http://hal.upmc.fr/hal-01383368
http://hal.upmc.fr/hal-01383368/document
http://hal.upmc.fr/hal-01383368/file/Agard_2016_Plate_interface.pdf
DOI : 10.1016/j.epsl.2016.06.054

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
In this paper, the generalized Stokes problem αu−νΔu+∇p=f, ∇u=0, is considered, where ν denotes the kinematic viscosity, α is a positive parameter proportional to the inverse of the time-step, and the source term f gathers the external forcing, the nonlinear term, and the explicit part of the linear term. The system is derived from a time discretization for the Navier-Stokes equation governing the motion of a two-dimensional incompressible fluid. A domain decomposition numerical method is developed for solving the system. The original domain is divided into several nonoverlapping subdomains, and in each subdomain the concerned equations are discretized by certain finite element methods. A new feature of the method is that the pressure p is required to be piecewise linear rather than piecewise constant, so that the nonphysical oscillations in the solution using piecewise linear pressure are eliminated. However, a difficulty in using piecewise linear pressure is that the Stokes problem in each subdomain involves Dirichlet boundary conditions on pressure at the interface, which is not a real Stokes problem. To avoid the difficulty, a modification is proposed which removes the continuity conditions on the pressure across the interface. In this way, the Stokes problem in each subdomain has only Dirichlet boundary conditions on the velocity. Formulations and discussions for both the methods are presented, which shows that the modified method is simpler than the original one. Numerical experiments are displayed to show the efficiency of the methods, especially that the modified method has the same accuracy as the original one.
ISSN: 0749-159X

hal-00730200
https://hal.archives-ouvertes.fr/hal-00730200

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Island arc picrites and boninites are magnesian magmatic rocks believed to be generated by high degrees of melting of depleted mantle sources fluxed by subduction-derived, volatile-rich components. These magmas can be probes of both the mantle wedge protoliths and subduction components, but are rare among other, usually more evolved, types of arc lavas. Furthermore, many arc picrites and boninites show evidence for late-stage differentiation prior to or during eruption, masking their primary, mantle-derived geochemical signatures. We report textural and chemical data on spinel-hosted melt inclusions of mantle origin in amphibole-bearing websterite veins cross-cutting spinel harzburgite xenoliths from the active andesitic Avacha volcano (south Kamchatka, Russia). The data are used to constrain the composition and origin of melts that formed the websterite veins in the sub-arc lithospheric mantle. The melt inclusions typically contain euhedral orthopyroxene and clinopyroxene and occasionally minor amphibole in silicate glass. The melt inclusions were homogenized using heating stages and gas-mixing furnaces. The homogenized glasses range from subalkaline primitive silica-rich picrite and high-Ca boninite (>15 wt % MgO, 48–54 wt % SiO2) to rhyolite. High-Ca boninite glasses have moderate volatile and low heavy rare earth element contents and elevated Cs, Rb, Ba, U, Sr, and Li abundances, with extremely high U/Th. In turn, the glasses display no negative spikes in the high field strength elements Nb, Ta, Zr, Hf, and Ti. We show that the silica-rich picrite and high-Ca boninite liquids in this study formed by high degrees of melting (>25%), at volatile under-saturation, of hybrid melt-depleted but silica-rich mantle sources at ≥1·5 GPa. The hybrid sources formed in two stages: first, by extraction of ∼15% melt from the convecting mantle to form a refractory protolith, which was subsequently enriched in silica via interaction with subduction-derived components prior to or during remelting in the mantle wedge. The subduction-derived components were enriched in fluid-mobile elements and probably oxidized. Overall, our results suggest that silica-rich picrites and high-Ca boninites can be primary melts in mature subduction zones and differentiate within the mantle wedge and the deep arc crust to form more evolved andesite magmas.
ISSN: 0022-3530

hal-01553676
https://hal.archives-ouvertes.fr/hal-01553676
DOI : 10.1093/petrology/egw066

Éditeur(s) : HAL CCSD
Résumé : International audience
The purpose of our study is to model a geothermal reservoir. When geothermal reservoir are assumed to be composed of pure water, the transfer of mass and energy is classically described by two balance equations: mass balance equation and the energy balance equation. In addition to those equations, fluid velocity ist classically given by the Darcy law while thermodynamic properties, inferred from theoretical or empirical equations of state, are used to close the mathematical system. Once this system is closed, there exist different solutions. The first one is to solve for pressure and temperature with a variable switch to saturation in the two-phase region (e.g. TOUGH2). The second one is to solve for pressure and enthalpy to increase stability of phase transition between single and two-phase states (e.g. Hydrotherm). We adopted the second option and chose te use a splitting method to get rid of the complexity of coupling equations and a finite volume method for the spatial discretization. Selecting object-oriented languages, we developed a multi-language framework, combining Python, Fortran and a C++ implementation of IAPWS (from the freesteam project) including the supercritical equations, in porous media velocity is given by Darcy law and to close the system physical properties are determined by the IAPWS-IF97 thermodynamic formulation. We resolve the equations in pressure and enthalpy instead of pressure and temperature in order to increase stability and to handle easier the passage from a single-phase to a two-phase system. We solve the system by using a splitting method - to get rid of the complexity of coupling equations - and a finite volume method. We offer some freedom to users thanks to the implementation of several methods like explicit or implicit Euler, Runge-Kutta or BDF2 for time solvers or GMRES and BICGSTAB for the linear solver. We can handle several boundary conditions like no-flow - describing a boundary which can not exchange matter with the exterior - or like a mixed-therm condition - a Dirichlet condition to the pressure and a Dirichlet or an outflow condition to the temperature in order to describe a recharge or a discharge zone - ... We're developing a multi-language framework, combining Python, Fortran and the C++ implementation of IAPWS (from the freesteam project). All these languages are object-oriented. We've applied this simulation model to the dogger in Paris, France, to several one-dimensional systems and a two-dimensional one made by Coumou with the CSMP++ platform. The dogger is a reservoir exploited to produce heat by pumping water at 70 and reinjecting it in the reservoir at 40. In the one-dimensional systems we wanted to observe the process of heat transfer from a higher temperature boundary to a smaller one in a high-energy domain. The last simulation shows the natural convection of water in a fault. For every simulation we compared the solutions we found with an other code (TOUGH2 or CSMP++) and they agreed. The next step will be to model the geothermal plant in Guadeloupe, West Indies. It's the only place in France - and in the West Indies so far - producing electricity with the earth power. The temperature can reach up to 1000 and the pressure range is around a few hundreds MPa. In some surface zones we can see two-phase water at atmospheric pressure. In the 1980s Bouillante was a laboratory for France. Since 1995 Bouillante has given 30GWh electricity a year to the Guadeloupeans.
PROCEEDINGS, Thirty-Ninth Workshop on Geothermal Reservoir Engineering
Stanford, United States

Droits : info:eu-repo/semantics/OpenAccess
hal-00944133
https://hal-brgm.archives-ouvertes.fr/hal-00944133
https://hal-brgm.archives-ouvertes.fr/hal-00944133/document
https://hal-brgm.archives-ouvertes.fr/hal-00944133/file/Copol.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Fault affecting silicoclastic sediments are commonly enriched in clay minerals. Clays are sensitive to fluid–rock interactions and deformation mechanisms; in this paper, they are used as proxy for fault activity and behavior. The present study focuses on clay mineral assemblages from the Point Vert normal fault zone located in the Annot sandstones, a Priabonian-Rupelian turbidite succession of the Alpine foredeep in SE France. In this area, the Annot sandstones were buried around 6–8 km below the front of Alpine nappes soon after their deposition and exhumed during the middle-late Miocene. The fault affects arkosic sandstone beds alternating with pelitic layers, and displays throw of about thirty meters. The fault core zone comprises intensely foliated sandstones bounding a corridor of gouge about 20 cm thick. The foliated sandstones display clay concentration along S–C structures characterized by dissolution of K-feldspar and their replacement by mica, associated with quartz pressure solution, intense microfracturation and quartz vein precipitation. The gouge is formed by a clayey matrix containing fragments of foliated sandstones and pelites. However, a detailed petrographical investigation suggests complex polyphase deformation processes. Optical and SEM observations show that the clay minerals fraction of all studied rocks (pelites and sandstones from the damage and core zones of the fault) is dominated by white micas and chlorite. These minerals have two different origins: detrital and newly-formed. Detrital micas are identified by their larger shape and their chemical composition with a lower Fe–Mg content than the newly-formed white micas. In the foliated sandstones, newly-formed white micas are concentrated along S–C structures or replace K-feldspar. Both types of newly formed micas display the same chemical composition confirmed microstructural observations suggesting that they formed in the same conditions. They have the following structural formulas: Na0.05 K0.86 (Al 1.77 Fe0.08 Mg0.15) (Si3.22 Al0.78) O10 (OH)2. They are enriched in Fe and Mg compared to the detrital micas. Newly-formed chlorites are associated with micas along the shear planes. According to microprobe analyses, they present the following structural formula: (Al1,48 Fe2,50 Mg1,84) (Si2,82 Al1,18) O10 (OH)8. All these data suggest that these clay minerals are synkinematic and registered the fault activity. In the gouge samples, illite and chlorite are the major clay minerals; smectite is locally present in some samples.In the foliated sandstones, Kubler Index (KI) ((001) XRD peak width at half height) data and thermodynamic calculations from synkinematic chlorite chemistry suggest that the main fault deformation occurred under temperatures around 220 °C (diagenesis to anchizone boundary). KI measured on pelites and sandstones from the hanging and footwall, display similar values coherent with the maximal burial temperature of the Annot sandstones in this area. The gouge samples have a higher KI index, which could be explained by a reactivation of the fault at lower temperatures during the exhumation of the Annot sandstones formation
ISSN: 0191-8141

hal-01172423
https://hal.archives-ouvertes.fr/hal-01172423
DOI : 10.1016/j.jsg.2015.03.012

Éditeur(s) : HAL CCSD
Résumé : International audience
INTRODUCTION: There are no French guidelines for the management of complicated parapneumonic effusions. A national observational study was carried out to assess the main features of current clinical practice for this condition. MATERIAL AND METHODS: A questionnaire was sent by email to the 1500 members of the Société de Pneumologie de Langue Française (SPLF) between 15th November and 15th December 2012. RESULTS: There were 92 responders, i.e. a response rate of 6%. Of these, 87 physicians mentioned that they were involved in the management of patients with complicated parapneumonic effusions with a median number of cases of 10 per year (IQR: 5-20). Chest tube drainage was the main approach used for pleural fluid aspiration (n=51/87), followed by repeated thoracentesis (n=29/87) and early surgery (1/87). Five physicians answered both chest tube drainage or repeated thoracentesis and one physician either chest tube drainage or early surgery. Pleural fibrinolytics were never used by 20% of physicians, only in case of loculations by 70% and by 10% of respondents in all cases. Only 3 physicians combined fibrinolytics with DNAse. A double antibiotic dose was used by one third of physicians. All the physicians used respiratory physiotherapy during hospitalization and to aid recovery. Follow-up practices were heterogeneous. CONCLUSIONS: The management of complicated parapneumonic effusions varies significantly in France. National guidelines may be helpful to define best practice and aid in its implementation.
Revue Des Maladies Respiratoires

hal-01146851
https://hal-univ-rennes1.archives-ouvertes.fr/hal-01146851
DOI : 10.1016/j.rmr.2015.01.001
PUBMED : 25725981

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
We study if the multilevel algorithm introduced by Debussche, T. Dubois and R. Temam [Theoret. Comput. Fluid Dynam. 7 (1995), no. 4, 279-315; Zbl 838.76060] and Dubois, F. Jauberteau and Temam [J. Sci. Comput. 8 (1993), no. 2, 167-194; MR1242960 (94f:65098)] for the 2D Navier-Stokes equations with periodic boundary conditions and spectral discretization can be generalized to more general boundary conditions and to finite elements. We first show that a direct generalization, as in [C. Calgaro, J. Laminie and R. Temam, Appl. Numer. Math. 23 (1997), no. 4, 403-442; MR1453424 (98d:76124)], for the Burgers equation, would not be very efficient. We then propose a new approach where the domain of integration is decomposed into subdomains. This enables us to define localized small-scale components and we show that, in this context, there is a good separation of scales. We conclude that all the ingredients necessary for the implementation of the multilevel algorithm are present.
ISSN: 0271-2091

hal-00730709
https://hal.archives-ouvertes.fr/hal-00730709

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
Sickle cell anaemia (SCA) is the most frequent genetic haemoglobinopathy, which exhibits a highly variable clinical course characterized by hyper-coagulable and pro-inflammatory states, as well as endothelial dysfunction. Extracellular microvesicles are released into biological fluids and play a role in modifying the functional phenotype of target cells. We hypothesized that potential differences in plasma-derived extracellular microvesicles (EV) function and cargo from SCA patients may underlie divergent clinical trajectories. Plasma EV from SCA patients with mild, intermediate and severe clinical disease course were isolated, and primary endothelial cell cultures were exposed. Endothelial cell activation, monocyte adhesion, barrier disruption and exosome cargo (microRNA microarrays) were assessed. EV disrupted the endothelial barrier and induced expression of adhesion molecules and monocyte adhesion in a SCA severity-dependent manner compared to healthy children. Microarray approaches identified a restricted signature of exosomal microRNAs that readily distinguished severe from mild SCA, as well as from healthy children. The microRNA candidates were further validated using quantitative real time polymerase chain reaction assays, and revealed putative gene targets. Circulating exosomal microRNAs may play important roles in predicting the clinical course of SCA, and in delineation of individually tailored, mechanistically-based clinical treatment approaches of SCA patients in the near future.
ISSN: 0007-1048

hal-01668328
https://hal.univ-antilles.fr/hal-01668328
DOI : 10.1111/bjh.14104

Éditeur(s) : HAL CCSD American Society for Microbiology
Résumé : International audience
Pneumocystis jirovecii pneumonia (PCP) is a life-threatening infection in immunocompromised patients. Quantitative real-time PCR (qPCR) is more sensitive than microscopic examination for the detection of P. jirovecii but also detects colonized patients. Hence, its positive predictive value (PPV) needs evaluation. In this 4-year prospective observational study, all immunocompromised patients with acute respiratory symptoms who were investigated for PCP were included, totaling 659 patients (814 bronchoalveolar lavage fluid samples). Patients with negative microscopy but positive qPCR were classified through medical chart review as having retained PCP, possible PCP, or colonization, and their clinical outcomes were compared to those of patients with microscopically proven PCP. Overall, 119 patients were included for analysis, of whom 35, 41, and 43 were classified as having retained PCP, possible PCP, and colonization, respectively. The 35 patients with retained PCP had clinical findings similar to those with microscopically proven PCP but lower fungal loads (P extless 0.001) and were mainly non-HIV-infected patients (P extless 0.05). Although the mean amplification threshold was higher in colonized patients, it was not possible to determine a discriminant qPCR cutoff. The PPV of qPCR in patients with negative microscopy were 29.4% and 63.8% when considering retained PCP and retained plus possible PCP, respectively. Patients with possible PCP had a higher mortality rate than patients with retained PCP or colonization (63% versus 3% and 16%, respectively); patients who died had not received co-trimoxazole. In conclusion, qPCR is a useful tool to diagnose PCP in non-HIV patients, and treatment might be better targeted through a multicomponent algorithm including both clinical/radiological parameters and qPCR results.
ISSN: 0095-1137

hal-01063906
https://hal.archives-ouvertes.fr/hal-01063906
DOI : 10.1128/JCM.01480-14
PUBMED : 25009050

Éditeur(s) : HAL CCSD
Résumé : Processes that occur within and across the oceanic crust–in particular along mid-ocean ridges and oceanic spreading centers—play a huge role in the dynamics of the Earth. The largest fluxes of heat and material between the Earth's mantle, crust, and seawater occur via magmatic, tectonic, and hydrothermal processes along oceanic spreading centers and their vast flanks. Roughly two thirds of the Earth's surface is accreted through magmatic and tectonic processes along mid-ocean ridges, and subduction of this ocean crust in turn influences mantle compositions. Exchange of elements between ocean crust and seawater strongly influences seawater compositions and leaves a geologic record of fluid-rock reactions in altered ocean crust. Some of these reactions contribute energy to microbial activity of a largely unexplored biosphere. The dynamics of ridge and ocean crustal processes therefore have enormous implications for thermal, chemical, and biological exchanges between the solid Earth and the hydrosphere.
EOS

hal-00564842
https://hal.archives-ouvertes.fr/hal-00564842
DOI : 10.1029/2010EO150001

Éditeur(s) : HAL CCSD Geological Society of America
Résumé : International audience
Porous sandstones tend to deform by the formation of low-permeability deformation bands that influence fluid flow in reservoir settings. The bands may be distributed or localized into clusters, and limited recent data suggest that tectonic regime may exert control on their distribution and clustering. In order to explore this suggestion, we performed a synthetic analysis based of 73 sets of bands, including 22 new sets measured for a reverse Andersonian regime that fill the important gap in data for this context. We find a surprisingly strong correlation between clustering and tectonic regime, where bands clearly are more distributed in the reverse regime compared to the normal regime. Together with the observed band distributions, capillary pressure data show evidence that efficient membrane seals are expected for extension, whereas pervasive permeability anisotropy is expected for contraction. Such a basic new rule concerning tectonic regime is very useful for assessment of reservoir properties where deformation bands are common but below seismic resolution.
ISSN: 0091-7613

hal-01355925
https://hal.archives-ouvertes.fr/hal-01355925
DOI : 10.1130/G37585.1

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The objective of the study was to evaluate the distribution of methotrexate (MTX) in cerebrospinal fluid (CSF) lateral ventricles and in cisterna magna after 3rd intraventricular CSF administration in a rabbit model.MTX or gadolinium chelate (Gd-DOTA) was administered in the 3rd ventricle with a local microdialysis to study the pharmacokinetics at the site of administration and with a simultaneous magnetic resonance imaging (MRI) acquisition in the 3rd ventricle, the lateral ventricles and in the cisterna magna. A specific CSF Physiologically Based Pharmacokinetic (PBPK) model was then extrapolated for MTX from Gd-DOTA data.The relative contribution of elimination and distribution processes to the overall disposition of MTX and Gd-DOTA in the 3rd ventricle was similar (i.e., around 60% for CLE and 40% for CLI) suggesting that Gd-DOTA was a suitable surrogate marker for MTX disposition in ventricular CSF. The PBPK predictions for MTX both in CSF of the 3rd ventricle and in plasma were in accordance with the in vivo results.The present study showed that the combination of local CSF microdialysis with MRI acquisition of the brain ventricles and a PBPK model could be a useful methodology to estimate the drug diffusion within CSF ventricles after direct brain CSF administration. Such a methodology would be of interest to clinicians for a rationale determination and optimization of drug dosing parameters in the treatment of leptomeningeal metastases.
ISSN: 0939-6411

hal-01335562
https://hal.archives-ouvertes.fr/hal-01335562
https://hal.archives-ouvertes.fr/hal-01335562/document
https://hal.archives-ouvertes.fr/hal-01335562/file/PBPK%20model%20of%20methotrexate%20in%20cerebrospinal%20fluid.pdf
DOI : 10.1016/j.ejpb.2016.04.012

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The analysis of three cataclastic band sets from Provence (France) reveals that the band density, their conjugate angles, their ratio of shear displacement to compaction, and the amount of cataclasis within the bands differ and can be expressed as functions of tectonic setting and petrophysical properties. We identify (1) a dense and closely spaced network of shear-enhanced (reverse) compaction bands; (2) a regularly spaced less dense network of reverse compactional shear bands; and (3) a localized network of normal shear bands. The field data show that strain localization is favored in an extensional regime and is characterized by shear bands with a large shear to compaction ratio and a small conjugate band angle. In contrast, distributed strain is favored in a contractional regime and is characterized by compactional bands with a low ratio of shear to compaction and a large conjugate band angle. To explain the mechanical origin of this strain localization, we quantify the yield strength and the stress evolution in extensional and contractional regimes in a frictional porous granular material. We propose a model of strain localization in porous sands as a function of tectonic stresses, burial depth, material properties, strain hardening and fluid pressure. Our model suggests that stress reduction, inherent to extensional regime, favors strain localization as shear bands, whereas stress increase during contraction favors development of compactional bands.
ISSN: 0191-8141

hal-00856921
https://hal.archives-ouvertes.fr/hal-00856921
DOI : 10.1016/j.jsg.2012.11.011

Éditeur(s) : HAL CCSD Elsevier
Résumé : Carbon emission at volcanic centers requires a constant balance between output (mostly by volcanism, either at plate boundaries or intraplate) and input (mostly at trench settings) of carbon from and to the Earth's mantle. The form of carbon that resides in the mantle is controlled by depth (pressure) and oxygen fugacity, the latter in turn depending on the depth and the concentration of iron in the mantle. In the shallow, lithospheric mantle, carbon is likely to be present in the oxidized form of CO2 (except under cratons where carbon is reduced to graphite or diamond). Below approximately 90 km, in the asthenosphere, the oxidized form of carbon is carbonate, either mineral or melt, depending on the thermal regime. At depths greater than approximately 150 km, the asthenospheric mantle is too reducing for carbon to stay in its oxidized form and only diamond is present, unless there is sufficient hydrogen to form reduced C–H fluids. Hence, the region located in the depth range of 90 to 150 km deep is where carbonatitic melts can most likely be produced and impregnate the surrounding mantle through metasomatism. The upper bound of this region is called the carbonate ledge. This limit prevents carbonate (either solid or molten) from ascending because of degassing and CO2 liberation. The lower bound is a redox front where redox melting (that is, melting caused by oxidation) may take place in an ascending portion of carbon-containing mantle. Carbonatite eruptions and presence of carbonate mineral inclusions in deep-seated diamonds provide evidence that these boundaries can be trespassed in some cases.An analysis of the experimental data that has bearing on silicate melting in the presence of carbon further shows that the carbonate ledge is a melting curve with a negative or flat Clapeyron (dP/dT) slope. In the carbonated ultrabasic (peridotite) systems, the carbonate ledge is located between ~ 2–3 GPa. The ledge divides the pressure–temperature space into a region of low-pressure silicate melt production, and a high-pressure region where carbonatites can be produced. Carbonatitic melts in equilibrium with mantle peridotite have compositions close to dolomitic (approximately equal amounts of Ca and Mg) with a general trend of becoming markedly more magnesian with increasing pressure. Calcic carbonatites may be stable at pressures < 2 GPa if clinopyroxene is absent. At mantle transition zone pressure range, there seems to be a melting temperature decrease (negative fusion slope), which may be caused by the stabilization of majoritic garnet.The carbonated basic (broadly eclogitic) system is more complex than the peridotitic one, because of the strong control of bulk silicate composition on melting temperatures, and hence, on melt composition. In carbonated eclogite systems, we propose that the effect of bulk composition upon all observed features can perhaps be related to silica super-saturation, or lack thereof. In some cases, high calcium (> 80 mol% CaCO3) melts can be produced, making the melting of carbonated eclogites an appealing scenario for the genesis of calcio-carbonatites in the Earth's mantle. Comparison with modeled pressure–temperature paths of subducted oceanic lithosphere shows that fusion of carbonated eclogite at depths shallower than 200 km should be expected for hot (Cascadian-type) subduction thermal regimes. On the other hand, in the case of cooler thermal regimes (Honshu-type, for instance), subducted carbonates may be stable to greater depths in Earth at trench settings, depending on the bulk composition of the system.Furthermore, high-pressure experiments show evidence of a continuum among carbonatitic, kimberlitic, melilititic, and basaltic liquids, for increasing melting degree of carbonated peridotite. This continuum has not been documented in the case of fusion of carbonated eclogite. It may be present, however, when certain sediments are fused, although the silicate melts are granitic to rhyodacitic instead of being kimberlitic in composition. Additional high-pressure work on phase relations in the simple binary system CaCO3–MgCO3 and specific focus on oxide solubility in the vapor phase have the potential to further clarify phase relations on complex silicate–carbonate systems at mantle conditions.
ISSN: 0009-2541

hal-01277770
https://hal.archives-ouvertes.fr/hal-01277770
DOI : 10.1016/j.chemgeo.2015.05.018

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Improving the prediction of sub-seismic structures and their petrophysical properties is essential for realistic characterization of deformed sandstone reservoirs. In the present paper, we describe permeability contrasts induced by cataclastic deformation bands and faults in porous sandstones (766 data synthesized from field examples and the literature). We also discuss the influence of several factors, including tectonic regime, presence of a fault, burial depth, host sandstone porosity, and grain size and sorting for their initiation and permeability. This analysis confirms that permeability decrease is as a function of grain-crushing intensity in bands. Permeability reduction ranges from very limited in crush-microbreccia of compaction bands to high permeability reduction in cataclasites and ultracataclasites of shear-dominated bands, band clusters and faults. Tectonic regime, and especially normal-fault regime, with its tendency to localize strain and generate faults, is identified as the most important factor, leading to the formation of cataclastic bands with high permeability contrasts. Moreover, moderate burial depth (1–3 km) favors cataclastic bands with high permeability contrasts with respect to the host sandstone. High porosity, coarse-grain size and good grain sorting can slightly amplify the permeability reductions recorded in bands.
ISSN: 0191-8141

hal-01218408
https://hal.archives-ouvertes.fr/hal-01218408
DOI : 10.1016/j.jsg.2015.03.013