Éditeur(s) : HAL CCSD MDPI
Résumé : International audience
AbstractThis review provides a global overview of microporous silica based membranes for desalination via pervaporation with a focus on membrane synthesis and processing, transport mechanisms and current state of the art membrane performance. Most importantly, the recent development and novel concepts for improving the hydro-stability and separating performance of silica membranes for desalination are critically examined. Research into silica based membranes for desalination has focussed on three primary methods for improving the hydro-stability. These include incorporating carbon templates into the microporous silica both as surfactants and hybrid organic-inorganic structures and incorporation of metal oxide nanoparticles into the silica matrix. The literature examined identified that only metal oxide silica membranes have demonstrated high salt rejections under a variety of feed concentrations, reasonable fluxes and unaltered performance over long-term operation. As this is an embryonic field of research several target areas for researchers were discussed including further improvement of the membrane materials, but also regarding the necessity of integrating waste or solar heat sources into the final process design to ensure cost competitiveness with conventional reverse osmosis processes. © 2012 by the authors.
ISSN: 2073-4441

hal-01683200
https://hal.univ-antilles.fr/hal-01683200
DOI : 10.3390/w4030629

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
An inter-laboratory exercise was organized under the PHARMAS EU project, by the Advanced School of Public Health (EHESP), in order to evaluate the performances of analytical methods for the measurement of antibiotics in waters (surface and tap). This is the first time such an exercise on antibiotics has been organized in Europe, using different kinds of analytical methods and devices. In this exercise thirteen laboratories from five countries (Canada, France, Italy, the Netherlands and Portugal) participated, and a total number of 78 samples were distributed. During the exercise, 2 testing samples (3 bottles of each) prepared from tap water and river water, respectively, spiked with antibiotics, were sent to participants and analyzed over a period of one month. A final number of 77 (98.7%) testing samples were considered. Depending on substances studied by each participant, 305 values in duplicate were collected, with the results for each sample being expressed as the target concentration. A statistical study was initiated using 611 results. The mean value, standard deviation, coefficient of variation, standard uncertainty of the mean, median, the minimum and maximum values of each series as well as the 95% confidence interval were obtained from each participant laboratory. In this exercise, 36 results (6% of accounted values) were outliers according to the distribution over the median (box plot). The outlier results were excluded. In order to establish the stability of testing samples in the course of the exercise, differences between variances obtained for every type of sample at different intervals were evaluated. The results showed no representative variations and it can be considered that all samples were stable during the exercise. The goals of this inter-laboratory study were to assess results variability when analysis is conducted by different laboratories, to evaluate the influence of different matrix samples, and to determine the rate at which participating laboratories successfully completed the tests initiated.
Talanta

hal-00878118
https://hal.archives-ouvertes.fr/hal-00878118
DOI : 10.1016/j.talanta.2012.06.064
PUBMED : 22939142

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Fault affecting silicoclastic sediments are commonly enriched in clay minerals. Clays are sensitive to fluid–rock interactions and deformation mechanisms; in this paper, they are used as proxy for fault activity and behavior. The present study focuses on clay mineral assemblages from the Point Vert normal fault zone located in the Annot sandstones, a Priabonian-Rupelian turbidite succession of the Alpine foredeep in SE France. In this area, the Annot sandstones were buried around 6–8 km below the front of Alpine nappes soon after their deposition and exhumed during the middle-late Miocene. The fault affects arkosic sandstone beds alternating with pelitic layers, and displays throw of about thirty meters. The fault core zone comprises intensely foliated sandstones bounding a corridor of gouge about 20 cm thick. The foliated sandstones display clay concentration along S–C structures characterized by dissolution of K-feldspar and their replacement by mica, associated with quartz pressure solution, intense microfracturation and quartz vein precipitation. The gouge is formed by a clayey matrix containing fragments of foliated sandstones and pelites. However, a detailed petrographical investigation suggests complex polyphase deformation processes. Optical and SEM observations show that the clay minerals fraction of all studied rocks (pelites and sandstones from the damage and core zones of the fault) is dominated by white micas and chlorite. These minerals have two different origins: detrital and newly-formed. Detrital micas are identified by their larger shape and their chemical composition with a lower Fe–Mg content than the newly-formed white micas. In the foliated sandstones, newly-formed white micas are concentrated along S–C structures or replace K-feldspar. Both types of newly formed micas display the same chemical composition confirmed microstructural observations suggesting that they formed in the same conditions. They have the following structural formulas: Na0.05 K0.86 (Al 1.77 Fe0.08 Mg0.15) (Si3.22 Al0.78) O10 (OH)2. They are enriched in Fe and Mg compared to the detrital micas. Newly-formed chlorites are associated with micas along the shear planes. According to microprobe analyses, they present the following structural formula: (Al1,48 Fe2,50 Mg1,84) (Si2,82 Al1,18) O10 (OH)8. All these data suggest that these clay minerals are synkinematic and registered the fault activity. In the gouge samples, illite and chlorite are the major clay minerals; smectite is locally present in some samples.In the foliated sandstones, Kubler Index (KI) ((001) XRD peak width at half height) data and thermodynamic calculations from synkinematic chlorite chemistry suggest that the main fault deformation occurred under temperatures around 220 °C (diagenesis to anchizone boundary). KI measured on pelites and sandstones from the hanging and footwall, display similar values coherent with the maximal burial temperature of the Annot sandstones in this area. The gouge samples have a higher KI index, which could be explained by a reactivation of the fault at lower temperatures during the exhumation of the Annot sandstones formation
ISSN: 0191-8141

hal-01172423
https://hal.archives-ouvertes.fr/hal-01172423
DOI : 10.1016/j.jsg.2015.03.012

Éditeur(s) : HAL CCSD Springer Verlag (Germany) Springer Verlag
Résumé : Dehydration reactions result in minerals’ replacement and a transient fluid-filled porosity. These reactions involve interface-coupled dissolution–precipitation and might therefore lead to fixed crystallographic orientation relations between reactant (protolith) and product phases (i.e. topotaxy). We investigate these two phenomena in the dehydration of a foliated antigorite (atg) serpentinite by comparing the crystallographic preferred orientation (CPO) developed by olivine (ol), orthopyroxene (opx) and chlorite (chl) during high-pressure antigorite and chlorite dehydration in piston-cylinder experiments and in natural samples recording the dehydration of antigorite (Cerro del Almirez, Betic Cordillera, Spain). Experiments were performed under undrained conditions resulting in fluid-filled porosity and in strong CPO of the prograde minerals, controlled by the pre-existing antigorite CPO in the reactant foliated serpentinite. The orientation of a ol,opx and c∗chl is parallel to c∗atg from the protolith. The Cerro del Almirez samples show similar, locally well-developed topotactic relations between orthopyroxene, chlorite and antigorite, but the product CPOs are weaker and more complex at the thin section scale. In contrast to the experiments, olivine from natural samples shows a weak correlation between b ol and the former c∗atg. We relate the strengthening of local topotactic relations and the weakening of the inherited CPO at a larger scale in natural samples to compaction and associated fluid migration. Microstructural features that might be related to compaction in the natural samples include: (1) smooth bending of the former foliation, (2) gradual crystallographic misorientation (up to 16°) of prismatic orthopyroxene due to buckling by dislocation creep, (3) inversion of enstatite to low clinoenstatite (P21/c) along lamellae and (4) brittle fracturing of prismatic orthopyroxene enclosed by plastically deformed chlorite. The coexistence of orthopyroxene buckling and clinoenstatite lamellae enables estimating the local strain rates and shear stresses generated during compaction. An lower bound for the strain rates in the order of 10−12 to 10−13 s−1 and shear stresses of 60–70 MPa are estimated based on creep data. Lower shear stresses (20–40 MPa) are retrieved using a theoretical approach. These data point to slow compaction (and fluid extraction) in nature if the system is not perturbed by external forces, with rates only marginally higher than the viscoplastic deformation of the solid matrix.
ISSN: 0010-7999

hal-01174158
https://hal.archives-ouvertes.fr/hal-01174158
DOI : 10.1007/s00410-015-1129-4

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
1. A substantial fraction of the freshwater available in neotropical forests is impounded within the rosettes of bromeliads that form aquatic islands in a terrestrial matrix. The ecosystem functioning of bromeliads is known to be influenced by the composition of the contained community but it is not clear whether bromeliad food webs remain functionally similar against a background of variation in the understorey environment. 2. We considered a broad range of environmental conditions, including incident light and incoming litter, and quantified the distribution of a very wide range of freshwater organisms (from viruses to macroinvertebrates) to determine the factors that influence the functional structure of bromeliad food webs in samples taken from 171 tank-bromeliads. 3. We observed a gradient of detritus-based to algal-based food webs from the understorey to the overstorey. Algae, rotifers and collector and predatory invertebrates dominated bromeliad food webs in exposed areas, whereas filter-feeding insects had their highest densities in shaded forest areas. Viruses, bacteria and fungi showed no clear density patterns. Detritus decomposition is mainly due to microbial activity in understorey bromeliads where filter feeders are the main consumers of microbial and particulate organic matter (POM). Algal biomass may exceed bacterial biomass in sun-exposed bromeliads where amounts of detritus were lower but functional diversity was highest. 4. Our results provide evidence that tank-bromeliads, which grow in a broad range of ecological conditions, promote aquatic food web diversity in neotropical forests. Moreover, although bromeliad ecosystems have been categorised as detritus-based systems in the literature, we show that algal production can support a non-detrital food web in these systems.
ISSN: 0046-5070

hal-00819103
https://hal.archives-ouvertes.fr/hal-00819103

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Several recent studies have documented that reactions between melt and crystal mush in primitive gabbroic rocks (via reactive porous flow) have an important control in the formation of the lower oceanic crust and the evolution of MORBs. In this context, olivine-rich rocks can form either by fractional crystallization of primitive melts or by open system reactive percolation of pre-existing (possibly mantle-derived) olivine matrix. To address this question, we performed in-situ trace element analyses (by LA-ICP-MS) of olivine from the Erro-Tobbio ophiolite Unit (Ligurian Alps), where mantle peridotites show gradational contacts with an hectometer-scale body of troctolites and plagioclase wehrlites, and both are cut by later decameter-wide lenses and dykes of olivine gabbros. Previous studies inferred that troctolites and olivine gabbros represent variably differentiated crystallization products from primitive MORB-type melts. Olivines in the three rock types (mantle peridotites, troctolites, olivine gabbros) exhibit distinct geochemical signature and well-defined elemental correlations. As expected, compatible elements (e.g. Ni) show the highest concentrations in peridotites (2580–2730 ppm), intermediate in troctolites (2050–2230 ppm) and lowest in gabbros (1355–1420 ppm), whereas moderate incompatible elements (e.g. Mn, Zn) show the opposite behaviour. By contrast, highly incompatible elements like Zr, Hf, Ti, HREE are variably enriched in olivines of troctolites, and the enrichment in absolute concentrations is coupled to development of significant HFSE/REE fractionation (ZrN/NdN up to 80). AFC modelling shows that such large ZrN/NdN ratios in olivines are consistent with a process of olivine assimilation and plagioclase crystallization at decreasing melt mass, in agreement with textural observations. In-situ trace element geochemistry of olivine, combined with microstructural investigations, thus appears a powerful tool to investigate reactive percolation and the origin of olivine-rich rocks in the lower oceanic crust.
ISSN: 0016-7037

hal-01419938
https://hal.archives-ouvertes.fr/hal-01419938
DOI : 10.1016/j.gca.2016.06.029

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The interpretation of coseismic surface deformation measurements through inversion techniques is of major importance to understand the mechanical behaviour of a seismic fault. Dense geodetic data sets in the vicinity of the ruptured fault provide unique constraints on detailed fault geometry and slip distribution at depth, making them complementary to seismological data. Bam earthquake (Mw 6.6, 2003 December 26) induced surface deformation has been precisely mapped by Envisat ASAR interferometry and by subpixel correlation techniques applied to Spot-5 and ASAR amplitude images. These oblique and horizontal estimations of deformation have been completed with one levelling profile along the main road crossing the rupture from west to east. We process these data (separately and jointly) in a two-step inversion technique, within the elastic half-space theory framework. Our objective is to determine the dislocation model at depth that satisfies simultaneously all the geodetic constraints. Also, we estimate the relative contribution of each geodetic data set to this inversion process.We first use a stochastic direct approach called neighbourhood algorithm in order to estimate the average characteristics of the rupture, and their relative uncertainty. Constraining in this way the geometry of the ruptured fault, we then linearize the inverse problem and compute the slip distribution on the fault using a standard weighted least-square technique, assuming the solution is smooth to some degree. At each step, we discuss the optimal models, their stability as well as the relative influence of each data set on the derived models parameters. Our preferred model reveals a shallow dislocation on a quasi-vertical fault, slightly dipping towards east. The slip vector has a strike-slip component as high as 2 m, while the dip-slip component seems negligible.However, the estimation of the resolution matrices emphasizes the fact that the details of deep fault slip distribution remain out of the scope of this ill-conditioned inverse problem. Yet, our preferred model suggests a main dislocation limited at depth between 1 and 6 km. By contrast, the aftershocks observed in the months following the earthquake are located just beneath the estimated main shock.
ISSN: 0956-540X

hal-00314173
https://hal.archives-ouvertes.fr/hal-00314173
https://hal.archives-ouvertes.fr/hal-00314173/document
https://hal.archives-ouvertes.fr/hal-00314173/file/GJI-2007-169-849-briole.pdf
DOI : 10.1111/j.1365-246X.2007.03358.x

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
The embryonic development in Chione cancellata, from fertilization to straighthinge D-stage veliger larva, occurs in 24 h at 251C. Transmission (TEM) and scanning (SEM) electron microscopy show that morphogenetic processes result in a gastrula with two depressions, 4 h after fertilization (T014 h). Two hours later, one depression, located at the animal pole, develops into an open cave, the floor of which becomes the shell field, characterized by scarce microvilli, located below the lower face of the prototrochal pad. The invagination located at the vegetal pole is characterized by regular microvilli and constitutes the digestive tract. At T018 h, the late gastrula differentiates into a typical motile trochophore, possessing a well-developed prototroch delimiting anterior and posterior embryonic regions. At T019h, the shell field, located between the prototroch and the telotroch, appears as a saddle-shaped region with a wrinkled surface extending on both sides of the embryo, establishing bilateral symmetry. From TEM observations, the apical surface of the underlying cells possesses a modified glycocalyx featuring a dense pellicle overlapping the cells of the shell field. At T0112 h, the prototroch is displaced toward the anterior region by outgrowth of the shell material. TEM views show that the wrinkled surface observed with SEM corresponds to the periostracum, attached dorsally to the hinge and ventrally to the cells of the future mantle edge. At T0115 h, an alveolar matrix of proteinaceous material, which could contain calcite crystals, appears between the periostracum and the mantle. At T0124 h, prodissoconch I formation is completed and the D-stage larvae possess a calcified shell. At this stage of development, only one mantle fold is present, representing the outer fold. The periostracumsecreting cells are in contact with the marginal cells of the velum. This functional velum is composed of four bands of cilia. Our TEMobservations confirm previous descriptions of the velum ciliary bands obtained only from SEM analyses, such as described in other bivalves. The apical sense organ and the digestive tract are poorly developed. From observations at the ultrastructural level of shell differentiation in C. cancellata, we propose a new interpretation of shell differentiation, including hinge and ligament for bivalves as opposed to that described for gastropods.
ISSN: 1077-8306

hal-00755283
https://hal.univ-antilles.fr/hal-00755283
DOI : 10.1111/j.1744-7410.2006.00036.x

Éditeur(s) : HAL CCSD
Résumé :  
A closed depression is defined as a geomorphologic element where a sediment depository is encircled by hillslopes. Despite the fact that closed depressions are often the only stagnant water points in many European landscapes, few ecological researches on their plant assemblages have been done. The main goal of this study was to give first results of the environmental factors responsible for the vegetation composition, richness and rarity in the closed depressions of the Lorraine biogeographical district (Belgium, France and grand-duche de Luxembourg). We surveyed for plant presence 85 forest and 77 grassland closed depressions. For each site, wetland area, local environmental factors and regional connectivities registered. For each species, the Ellenberg values were compiled. To investigate the main source of variation in species composition and in species richness (including richness in rare species), Non-metric Multidimensional Scaling analyses and Generalized Linear Models were respectively used. Species pools in forest (forest and preforest species) and in grassland (bog plants, pioneers, helophytes) were quite different. In both landscapes, a gradient from plants typical of basic high-productive soils to plants typical of acid low-productive soils reflects a shared successional gradient. The accumulation of organic matter allowed the establishment of Sphagnum spp., which slowly acidified the soil and thus acted as ecosystem engineers for the arrival of bog plants. Moreover, the species composition was additionally driven by the plant light tolerance in forests and by the plant water requirements in grasslands. Mechanisms of species accumulation (increase in species richness) were different in forests and in grasslands: respectively related to the plant light tolerance and to the wetland area. At the regional level, the averaged soil productivity was negatively related to the richness in rare species. Indeed, perennial highly-competitive plants such as Glyceria spp., Iris pseudacorus or Urtica dioica impeded the establishment of smaller and rarer species. At the habitat level, isolated closed depressions (due to either low connectivity or low grazing pressure) have more habitat rare species, giving evidences of dispersal limitation in plant assemblages of closed depressions.
7th INTECOL International Wetland Conference
Utrecht, Netherlands

hal-01032381
https://hal.archives-ouvertes.fr/hal-01032381

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Continuous Global Positioning System (CGPS) position time series from eastern North America constrain the pattern and magnitude of regional crustal deformation. Initial analysis delineates consistent uplift patterns, as expected from glacial isostatic adjustment (GIA) predictions, but the associated horizontal deformation is not definitive, in part due to the short time periods for a significant number of the available stations. We employ an eigenpattern decomposition in order to define a unique, finite set of deformation patterns for this continuous GPS data. Similar in nature to the empirical orthogonal functions historically employed in the analysis of atmospheric and oceanographic phenomena, the method derives the eigenvalues and eigenstates from the diagonalization of the correlation matrix using a Karhunen-Loeve expansion (KLE). The KLE technique is used to identify the important modes in both time and space for the CGPS data, modes that potentially include signals such as horizontal and vertical GIA, tectonic strain, and seasonal effects. Here we filter both the vertical and horizontal velocity patterns on different spatiotemporal scales in order to study the potential geophysical sources, after the removal of correlated and random noise. The method is successful in disaggregating the linear vertical signal from more variable and less spatially correlated signals. The vertical and horizontal results are compared to the predictions of the ICE-3G GIA loading model with a number of plausible mantle viscosity profiles. The horizontal velocity analysis allows for qualitative differentiation between several potential GIA models and suggests that, with longer time series, this technique can be employed to remove correlated noise and improve estimates of crustal strain patterns and their sources.
ISSN: 0033-4553

hal-00795454
https://hal.archives-ouvertes.fr/hal-00795454
DOI : 10.1007/s00024-011-0420-1