Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
As previously suggested by many authors, shear wave splitting rneasurernents certainly provide the best insights on the tectonic structure (or fabric) of the upper mantle. Shear wave splitting pararneters are correlated with the flow fabric developed in the deforming upper mantle. Petrophysical analysis of peridotites [e.g., Kem et al., 1996; Mainprice and Silver, 1993] shows that the largest anisotropy is recorded for shear waves propagating close to the Y structural direction (i.e., normal to the lineation in the foliation plane) and that the fast split shear wa ve is polarized in a plane parallel to the X structural axis (i.e., the lineation, marked by the olivine a axis concentration). Mapping shear wave splitting parameters over a specific tectonic domain would therefore provide an image of the mantle fabric at depth.
ISSN: 2169-9313

hal-01389720
http://hal.univ-reunion.fr/hal-01389720
http://hal.univ-reunion.fr/hal-01389720/document
http://hal.univ-reunion.fr/hal-01389720/file/Vauchez_comment_JGR_1999_hal.pdf
DOI : 10.1029/1999JB900053

Éditeur(s) : HAL CCSD Geological Society of London
Résumé : International audience
This paper presents the background for the calculation of various numbers that can be used to characterize crystal-preferred orientation (CPO), also known as texture in materials science, for large datasets using the combined scripting possibilities of MTEX and MatLab®. The paper is focused on three aspects in particular: the strength of CPO represented by orientation and misorientation distribution functions (ODFs, MDFs) or pole figures (PFs); symmetry of PFs and components of ODFs; and elastic tensors. The traditional measurements of texture strength of ODFs, MDFs and PFs are integral measurements of the distribution squared. The M-index is a partial measure of the MDF as the difference between uniform and measured misorientation angles. In addition there other parameters based on eigen analysis, but there are restrictions on their use. Eigen analysis does provide some shape factors for the distributions. The maxima of an ODF provides information on the modes. MTEX provides an estimate of the lower bound uniform fraction of an ODF. Finally, we illustrate the decomposition of arbitrary elastic tensor into symmetry components as an example of components in anisotropic physical properties. Ten examples scripts and their output are provided in the appendix.
Geological Society Special Publication

hal-01277689
https://hal.archives-ouvertes.fr/hal-01277689
DOI : 10.1144/SP409.8

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Mobile-immobile mass transfer is widely used to model non-Fickian dispersion in porous media. Nevertheless, the memory function, implemented in the sink/source term of the transport equation to characterize diffusion in the matrix (i.e., the immobile domain), is rarely measured directly. Therefore, the question can be posed as to whether the memory function is just a practical way of increasing the degrees of freedom for fitting tracer test breakthrough curves or whether it actually models the physics of tracer transport. In this paper we first present a technique to measure the memory function of aquifer samples and then compare the results with the memory function fitted from a set of field-scale tracer tests performed in the same aquifer. The memory function is computed by solving the matrix diffusion equation using a random walk approach. The properties that control diffusion (i.e., mobile-immobile interface and immobile domain cluster shapes, porosity, and tortuosity) are investigated by X-ray microtomography. Once the geometry of the matrix clusters is measured, the shape of the memory function is controlled by the value of the porosity at the percolation threshold and of the tortuosity of the diffusion path. These parameters can be evaluated from microtomographic images. The computed memory function compares well with the memory function deduced from the field-scale tracer tests. We conclude that for the reservoir rock studied here, the atypical non-Fickian dispersion measured from the tracer test is well explained by microscale diffusion processes in the immobile domain. A diffusion-controlled mobileimmobile mass transfer model therefore appears to be valid for this specific case.
ISSN: 0043-1397

insu-00373705
https://hal-insu.archives-ouvertes.fr/insu-00373705
https://hal-insu.archives-ouvertes.fr/insu-00373705/document
https://hal-insu.archives-ouvertes.fr/insu-00373705/file/Gouze_et_al-2008-Water_Resources_Research.pdf
DOI : 10.1029/2007WR006690

Éditeur(s) : HAL CCSD
Résumé : 1 p.
For groundwater issues (potential leakages in waste repository, aquifer management ...), the development of modeling techniques is far ahead of the actual knowledge of aquifers. This raises two fundamental issues: 1) which and how much data are necessary to make predictions accurate enough for aquifer management issues; 2) which models remain relevant to describe the heterogeneity and complexity of geological systems. The French observatory H+ was created in 2002 with the twofold motivation of acquiring a large database for validating models of heterogeneous aquifers, and of surveying groundwater quality evolution in the context of environmental changes. H+ is a network of 4 sites (Ploemeur, Brittany, France; HES Poitiers, France; Cadarache, France; Campos, Mallorca, Spain) with different geological, climatic, and economic contexts. All of them are characterized by a highly heterogeneous structure (fractured crystalline basement for Ploemeur, karstified and fractured limestone for Poitiers, Cadarache and Mallorca), which is far to be taken into account by basic models. Ploemeur is exploited as a tap-water plant for a medium-size coastal city (15,000 inhabitants) for 20 years. Each site is developed for long term investigation and monitoring. They involves a dense network of boreholes, detailed geological and geophysical surveys, periodic campaigns and/or permanent measurements of groundwater flow, water chemistry, geophysical signals (including ground motions), climatic parameter, etc. Several large-scale flow experiments are scheduled per year to investigate the aquifer structure with combined geophysical, hydrogeological, and geochemical instruments. All this information is recorded in a database that has been developed to improve the sustainability and quality of data, and to be used as a collaborative tool for both site researchers and modelers. This project lasts now for 5 years. It is a short time to collect the amount of information necessary to apprehend the complexity of aquifers; but it is already enough to obtain a few important scientific results about the very nature of the flow heterogeneity, the origin and residence time of water elements, the kinetic of geochemical processes, etc. We have also developed new methods to investigate aquifers (in-situ flow measurements, flow experiment designs, groundwater dating, versatile in-situ probes, etc.). This experience aiming at building up long term knowledge appears extremely useful to address critical issues related to groundwater aquifers: the structure and occurrence of productive aquifer in crystalline basement, the assessment of aquifer protection area in the context of highly heterogeneous flow, the biochemical reactivity processes, the long term evolution of both water quantity and quality in the context of significant environmental changes, for instance.
AGU, Fall Meeting 2008
San Francisco, United States

insu-00375980
https://hal-insu.archives-ouvertes.fr/insu-00375980

Résumé : Dans le cadre de l'extension du RNO aux Antilles, un exercice d"intercomparaison des laboratoires pressentis pour effectuer les analyses du volet « hydrologie » a été organisé par l'IFREMER fin 2000-début 2001. L'exercice comportait l'analyse de cinq paramètres : salinité, nitrate, nitrite, ammonium et phosphate. Chacun des paramètres devait être analysé à deux niveaux de concentration. Les participants étaient au nombre de 3. Chaque laboratoire a reçu deux flacons de 250 ml pour la salinité et huit flacons de 150 ml pour les nutriments (un flacon par paramètre et par niveau). Les laboratoires étaient informés qu'ils devaient analyser les échantillons dans un délai de six semaines environ après réception, ce qui limitait les risques de dérive potentielle des concentrations pouvant provenir d'une instabilité accidentelle des échantillons. L'expédition a été effectuée au début décembre 2000, ce qui a permis une mise à disposition des échantillons dans les laboratoires pour la fin décembre. Ce rapport analyse les résultats de l'exercice et présente une interprétation de ceux-ci.

Droits : info:eu-repo/semantics/openAccess
http://archimer.ifremer.fr/doc/00018/12911/9866.pdf
http://archimer.ifremer.fr/doc/00018/12911/

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Tilt fluctuations can potentially reflect the response of hydrosystems to important rainfall. In this context, long baseline tiltmeters have been installed in an underground tunnel penetrating the Fontaine de Vaucluse karst to study the medium deformation related to solicitations exerted by water infiltrating the hydrosystem. The instruments monitor the tilt as well as its spatial variation. Northward tilts reaching a 1 μrad amplitude are observed consecutively to rainfalls. The tilt amplitude is highly correlated with the Fontaine de Vaucluse outlet flow fluctuations. The measured tilt signal is also relatively homogeneous over a 150 m length. Different types of structure likely to produce such observations are tested in order to identify their location with respect to the tiltmeters, their dimension as well as the amount of water level variation in the structure. Following rainfalls, the infiltration of water modifies the pore pressure, inducing a medium deformation. The hypothesis of an homogeneous surface loading on the Vaucluse plateau is first refuted since the related tilt is much lower than the one measured. The water supplied by rainfalls has to accumulate in discontinuities in order to generate a higher tilt. So, the deformation related to a pressure exerted on a fracture filled by water is assessed. A first study reveals the interest of the tilt homogeneity information that constrains strongly the fracture properties. Thus, the fracture must be located at a distance more than a few hundreds metres from the tiltmeters in order to produce a tilt homogeneous in space. If the fracture is initially dry, it must also be filled on a height higher than 150 m consecutive to a rainfall in order to generate a tilt amplitude in the same magnitude as the one measured. Then, we explore the influence of water level variations on the tilt produced by a fracture located at the interface between the saturated and unsaturated zones, which are thereby permanently flooded. Since several parameters of that model satisfactorily explain the field observations, we discuss how simultaneous geodetical observations could provide complementary information that would further constrain the geometry of the structure at the origin of the medium deformation.
ISSN: 0956-540X

insu-01408482
https://hal-insu.archives-ouvertes.fr/insu-01408482
https://hal-insu.archives-ouvertes.fr/insu-01408482/document
https://hal-insu.archives-ouvertes.fr/insu-01408482/file/Lesparre-2017.pdf
DOI : 10.1093/gji/ggw446

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Numerical programs for simulating flow and reactive transport in porous media are essential tools for predicting reservoir properties changes triggered by CO2 underground injection. At reservoir scale, meshed models in which equations are solved assuming that constant macroscopic properties can be defined in each cells, are widely used. However, the parameterization of the dissolution-precipitation problem and of the feedback effects of these processes on the flow field is still challenging. The problem arises from the mismatch between the scales at which averaged parameters are defined in the meshed model and the scale at which chemical reactions occur and modify the pore network geometry. In this paper we investigate the links between the dissolution mechanisms that control the porosity changes and the related changes of the reactive surface area and of the permeability. First, the reactive surface area is computed from X-ray microtomography data obtained before and after a set of dissolution experiments of pure calcite rock samples using distinctly different brine-CO2 mixtures characterizing homogeneous to heterogeneous dissolution regimes. The results are used to validate the power law empirical model relating the reactive surface area to porosity proposed by Luquot and Gauze (2009). Second, we investigate the spatial distribution of the effective hydraulic radius and of the tortuosity, two structural parameters that control permeability, in order to explain the different porosity-permeability relationships observed for heterogeneous and homogeneous dissolution regimes. It is shown that the increase of permeability is due to the decrease of the tortuosity for homogeneous dissolution, whereas it is due to the combination of tortuosity decrease and hydraulic radius increase for heterogeneous dissolution. For the intermediate dissolution regime, identified to be the optimal regime for increasing permeability with small changes in porosity, the increase of permeability results from a large increase in the mean effective hydraulic radius of the sample.
ISSN: 0169-7722

hal-00617671
https://hal.archives-ouvertes.fr/hal-00617671
DOI : 10.1016/j.jconhyd.2010.07.004

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : A preliminary version appeared in the 18th ACM-SIAM Symposium on Discrete Algorithms, pp. 746- 755, 2007
International audience
The Voronoi diagram of a finite set of objects is a fundamental geometric structure that subdivides the embedding space into regions, each region consisting of the points that are closer to a given object than to the others. We may define various variants of Voronoi diagrams depending on the class of objects, the distance function and the embedding space. In this paper, we investigate a framework for defining and building Voronoi diagrams for a broad class of distance functions called Bregman divergences. Bregman divergences include not only the traditional (squared) Euclidean distance but also various divergence measures based on entropic functions. Accordingly, Bregman Voronoi diagrams allow one to define information-theoretic Voronoi diagrams in sta- tistical parametric spaces based on the relative entropy of distributions. We define several types of Bregman diagrams, establish correspondences between those diagrams (using the Legendre transformation), and show how to compute them efficiently. We also introduce extensions of these diagrams, e.g. k-order and k-bag Bregman Voronoi diagrams, and introduce Bregman triangulations of a set of points and their connection with Bregman Voronoi diagrams. We show that these triangulations capture many of the properties of the celebrated Delaunay triangulation.
ISSN: 0179-5376

hal-00488441
https://hal.archives-ouvertes.fr/hal-00488441
https://hal.archives-ouvertes.fr/hal-00488441/document
https://hal.archives-ouvertes.fr/hal-00488441/file/BVD-DCG.pdf

Éditeur(s) : HAL CCSD Ecological Society of America
Résumé : Reliable assessment of fish origin is of critical importance for exploited species, since nursery areas must be identified and protected to maintain recruitment to the adult stock. During the last two decades, otolith chemical signatures (or "fingerprints") have been increasingly used as tools to discriminate between coastal habitats. However, correct assessment of fish origin from otolith fingerprints depends on various environmental and methodological parameters, including the choice of the statistical method used to assign fish to unknown origin. Among the available methods of classification, Linear Discriminant Analysis (LDA) is the most frequently used, although it assumes data are multivariate normal with homogeneous within-group dispersions, conditions that are not always met by otolith chemical data, even after transformation. Other less constrained classification methods are available, but there is a current lack of comparative analysis in applications to otolith microchemistry. Here, we assessed stock identification accuracy for four classification methods (LDA, Quadratic Discriminant Analysis [QDA], Random Forests [RF], and Artificial Neural Networks [ANN]), through the use of three distinct data sets. In each case, all possible combinations of chemical elements were examined to identify the elements to be used for optimal accuracy in fish assignment to their actual origin. Our study shows that accuracy differs according to the model and the number of elements considered. Best combinations did not include all the elements measured, and it was not possible to define an ad hoc multielement combination for accurate site discrimination. Among all the models tested, RF and ANN performed best, especially for complex data sets (e. g., with numerous fish species and/or chemical elements involved). However, for these data, RF was less time-consuming and more interpretable than ANN, and far more efficient and less demanding in terms of assumptions than LDA or QDA. Therefore, when LDA and QDA assumptions cannot be reached, the use of machine learning methods, such as RF, should be preferred for stock assessment and nursery identification based on otolith microchemistry, especially when data set include multispecific otolith signatures and/or many chemical elements.
ISSN: 1051-0761

hal-00644549
https://hal.archives-ouvertes.fr/hal-00644549
DOI : 10.1890/09-1887.1

Éditeur(s) : HAL CCSD
Résumé : International audience
This paper presents some considerations about hybrid optimization algorithms useful to optimize real complex system. The given indication could be used by readers to conceive hybrid algorithms. These considerations have been deducted from a concrete application case: the satellites constellations design problem. But each of the advanced techniques proposed in this paper are considered in a more general way to solve other problems. This problem is used to illustrate the techniques along the paper because it is grouping many characteristics (di culties) of contemporary real complex systems: the size and the characteristics of the search space engendered by a combinatorial problem; The irregularity of the criterions; The mathematical and physical heterogeneity of parameters forbids the use of classical algorithms; The evaluation of a solution, which uses a time consuming simulation; A need of accurate values. More details are available in previous papers ([?], [?], [?], [?]). For these reasons, we could learn a lot from this experiment in order to detach hybrid techniques usable for problems having close characteristics. This paper presents the historic leading to the current algorithm, the modeling of the complex system and the sophisticated algorithm proposed to optimize it. Application cases and ways to built signi cant tests of hybrid algorithm are also given.
HPCSE Proceedings
Toulouse, France

hal-00602264
https://hal.archives-ouvertes.fr/hal-00602264

Éditeur(s) : Pergamon-elsevier Science Ltd
Résumé : The south-west lagoon of New Caledonia is a wide semi-open coral reef lagoon bounded by an intertidal barrier reef and bisected by numerous deep inlets. This paper synthesizes findings from the 2000-2008 French National Program EC2CO-PNEC relative to the circulation and the transport of suspended particles in this lagoon. Numerical model development (hydrodynamic, fine suspended sediment transport, wind-wave, small-scale atmospheric circulation) allowed the determination of circulation patterns in the lagoon and the charting of residence time, the later of which has been recently used in a series of ecological studies. Topical studies based on field measurements permitted the parameterisation of wave set-up induced by the swell breaking on the reef barrier and the validation of a wind-wave model in a fetch-limited environment. The analysis of spatial and temporal variability of suspended matter concentration over short and long time-scales, the measurement of grain size distribution and the density of suspended matter (1.27 kg 1(-1)), and the estimation of erodibility of heterogeneous (sand/mud, terrigenous/biogenic) soft bottoms was also conducted. Aggregates were shown to be more abundant near or around reefs and a possible biological influence on this aggregation is discussed. Optical measurements enabled the quantification of suspended matter either in situ (monochromatic measurements) or remotely (surface spectral measurements and satellite observations) and provided indirect calibration and validation of a suspended sediment transport model. The processes that warrant further investigation in order to improve our knowledge of circulation and suspended sediment transport in the New Caledonia lagoon as well as in other coral reef areas are discussed, as are the relevance and reliability of the numerical models for this endeavour.
Marine Pollution Bulletin (0025-326X) (Pergamon-elsevier Science Ltd), 2010 , Vol. 61 , N. 7-12 , P. 269-296

Droits : 2010 Elsevier Ltd All rights reserved.
http://archimer.ifremer.fr/doc/00014/12526/9401.pdf
DOI:10.1016/j.marpolbul.2010.06.023
http://archimer.ifremer.fr/doc/00014/12526/

Éditeur(s) : HAL CCSD MDPI
Résumé : International audience
LiDAR (Light Detection And Ranging) remote sensing has been shown to be a good technique for the estimation of forest parameters such as canopy heights and above ground biomass. Whilst airborne LiDAR data are in general very dense but only available over small areas due to the cost of their acquisition, spaceborne LiDAR data acquired from the Geoscience Laser Altimeter System (GLAS) have a coarser acquisition density associated with a global cover. It is therefore valuable to analyze the integration relevance of canopy heights estimated from LiDAR sensors with ancillary data such as geological, meteorological, and phenological variables in order to propose a forest canopy height map with good precision and high spatial resolution.In this study, canopy heights extracted from both airborne and spaceborne LiDAR, were first extrapolated from available environmental data (e.g. geology, slope, vegetation indices, etc.). The estimated canopy height maps using random forest (RF) regression from the airborne or GLAS calibration datasets showed similar precisions (RMSE better than 6.5 m). In order to improve the precision of the canopy height estimates regression-kriging (kriging of random forest regression residuals) was used. Results indicated an improvement in the RMSE (decrease from 6.5 to 4.2 m) for the regression-kriging maps from the GLAS dataset, and from 5.8 to 1.8 m for the regression-kriging map from the airborne LiDAR dataset. Finally, in order to investigate the impact of the spatial sampling of future LiDAR missions on the precision of canopy height estimates, six subsets were derived from the initial airborne LiDAR dataset with flight line spacing of 5, 10, 20, 30, 40 and 50 km (corresponding to 0.29, 0.11, 0.08, 0.05, 0.04, and 0.03 points/km² respectively). Results indicated that using the regression-kriging approach achieved a precision of 1.8 m on the canopy height map with flight line spacing of 5 km and achieved an average RMSE of 4.8m for the configuration for the 50 km flight line spacing.
ISSN: 2072-4292

hal-01361343
https://hal.archives-ouvertes.fr/hal-01361343
https://hal.archives-ouvertes.fr/hal-01361343/document
https://hal.archives-ouvertes.fr/hal-01361343/file/mt2016-pub00048036.pdf
DOI : 10.3390/rs8030240

Éditeur(s) : HAL CCSD
Résumé : International audience
The aim of this study is to suggest an automated technique for distributed decision. It is based on protocol population deployed on Wireless Sensor Networks (WSN). This approach is able to help medical staff to detect earlier than usual some diseases on patients. It could be easily adapted for many other fields (fire monitoring, environment supervising, ...) In this context, a patient is equipped with health parameter transducers which are connected to a WSN. This WSN will perform some computations and raise an alarm when some diseases are suspected. The algorithm is distributed, i.e., the decision may be done by any mote dealing with the disease detection. The experimentations show promising results.
a venir
Denver, Colorado, United States

hal-00519597
https://hal.archives-ouvertes.fr/hal-00519597

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A recent study suggested that adenosine signaling pathway could promote hemolysis in patients with sickle cell anemia (SCA). This signaling pathway involves several gene coding enzymes for which variants have been described. In this study, we analyzed the genotype-phenotype relationships between functional polymorphisms or polymorphisms associated with altered expression of adenosine pathway genes, namely adenosine deaminase (ada; rs73598374), adenosine A2b receptor (adora2b; rs7208480), adenylyl cyclase6 (adcy6; rs3730071, rs3730070, rs7300155), and hemolytic rate in SCA patients. One hundred and fifty SCA patients were genotyped for adcy6, ada, and adora2b variants as well as alpha-globin gene, a genetic factor known to modulate hemolytic rate. Hematological and biochemical data were obtained at steady-state. Lactate dehydrogenase, aspartate aminotransferase, reticulocytes and total bilirubin were used to calculate a hemolytic index. Genotype-phenotype relationships were investigated using parametric tests and multivariate analysis. SCA patients carrying at least one allele of adcy6 rs3730070-G exhibited lower hemolytic rate than non-carriers in univariate analysis (p=0.006). The presence of adcy6 rs3730070-G variant was associated with a decreased hemolytic rate in adjusted model for age and alpha-thalassemia (p=0.032). Our results support a protective effect of adcy6 rs3730070-G variant on hemolysis in SCA patients.
ISSN: 1079-9796

hal-01668332
https://hal.univ-antilles.fr/hal-01668332
DOI : 10.1016/j.bcmd.2016.02.006

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The diffusion of titanium along with Ni, Co and Mn in pure synthetic forsterite has been studied as a function of temperature, oxygen fugacity, crystallographic orientation and chemical potentials in the four-component system MgO–SiO2–TiO2–TiO1·5. In over 100 different experimental conditions, no Ti diffusion profiles with the classical shape of the error function were observed. Instead, the profiles vary between ‘stepped’ at high fO2 (probably owing to diffusion on octahedral sites and trapping in tetrahedral sites), to hockey-stick shapes at low fO2 owing to concentration-dependent diffusion. The profile shapes vary systematically between these end-members according to oxygen fugacity. These profile shapes are also reproduced in experiments using natural San Carlos olivine. The change in profile shape is interpreted to be a function of valence-state change from Ti4+ to Ti3+, shown by a sigmoidal log fO2–diffusivity relationship. To distinguish between Ti4+ and Ti3+ in forsterite, a diffusion profile was also investigated using ‘hydroxylation spectroscopy’ whereby a crystal from a diffusion experiment was hydroxylated by annealing in an H2O-rich fluid at moderate pressure and temperature. The point defects associated with the added structural OH were then determined by infrared spectroscopy, providing evidence for the presence of Ti4+ and Ti3+ at intermediate oxygen fugacity. The transition from Ti4+ to Ti3+ occurs at considerably higher fO2 in these diffusion experiments than in equilibrium experiments in similar systems. Titanium diffusion, qualified using a mobility parameter (M), is fastest along the c-axis, at high activity of silica, low oxygen fugacity and high temperature. The rate of Ti diffusion is broadly similar to those of Mn, Ni and Co, and closer to published rates of Mg self-diffusion in olivine than Si self-diffusion. The observed Ti3+ and Ti4+ diffusion occurs on the M-sites. From statistical examination of the large Mn, Ni and Co diffusivity dataset, we determine that there is a 102/3 dependence of diffusion on aSiO2; the cations diffuse more rapidly at high aSiO2. In addition, diffusivity has a 10–1/8 dependence on fO2, suggested to be the result of increased concentration of loosely bound Ti3+–vacancy pairs, which enhance the mobility of other cations. This behaviour is likely to be present in natural systems where trivalent (e.g. Fe3+, Al3+, Cr3+) and divalent cations diffuse together. Consideration should be given to diffusive interference by highly charged, fast-moving cations when extracting time scales from frozen diffusion profiles.
ISSN: 0022-3530

hal-01531344
https://hal.archives-ouvertes.fr/hal-01531344
DOI : 10.1093/petrology/egw067

Éditeur(s) : HAL CCSD
Résumé : International audience
In this paper, we investigate image segmentation by region merging. Given any similarity measure between regions , satisfying some weak constraints, we give a general predicate for answering if two regions are to be merged or not during the segmentation process. Our predicate is generic and has six properties. The first one is its inde-pendance with respect to the similarity measure, that leads to a user-independant and adaptative predicate. Second, it is non-parametric, and does not rely on any assumption concerning the image. Third, due to its weak constraints, knowledge may be included in the predicate to fit better to the user's behaviour. Fourth, provided the similarity is well-chosen by the user, we are able to upperbound one type of error made during the image segmentation. Fifth, it does not rely on a particular segmentation algorithm and can be used with almost all region-merging algorithms in various application domains. Sixth, it is calculated quickly, and can lead with appropriated algorithms to very efficient segmentation.
10th IEEE International Conference on Tools with Artificial Intelligence
Taipei, Taiwan

lirmm-01168371
https://hal-lirmm.ccsd.cnrs.fr/lirmm-01168371
https://hal-lirmm.ccsd.cnrs.fr/lirmm-01168371/document
https://hal-lirmm.ccsd.cnrs.fr/lirmm-01168371/file/FioNocICTAI98_Image%20Segmentation%20Using.pdf
DOI : 10.1109/TAI.1998.744885

Éditeur(s) : HAL CCSD North Atlantic Science Publishing Company
Résumé : International audience
In this paper, we extend the sensitivity analysis framework developed recently for variational inequalities by Noor and Yen to variational inclusions relying on Wiener-Hopf equation techniques. We prove the continuity and the Lipschitz continuity of the locally unique solution to parametric variational inclusions without assuming differentiability of the given data.
ISSN: 1048-9533

hal-00779240
https://hal.univ-antilles.fr/hal-00779240
https://hal.univ-antilles.fr/hal-00779240/document
https://hal.univ-antilles.fr/hal-00779240/file/681979_4_.pdf

Résumé : L’objet de cette thèse est l’étude des comportements mécanique et à la corrosion d’un nouveau système de fondation, dit pieux SPIRMEC, adapté aux structures légères. Le travail s’est focalisé sur deux grands aspects. Le premier aspect concerne l’analyse du comportement sous chargement axiale des pieux SPIRMEC sur la base de l’expérimentation et de la modélisation numérique dans un sol mou non cohésif. Quant au deuxième aspect, il traite du problème de la corrosion de l’acier constituant le pieu dans un environnement tropical humide. Le comportement des pieux SPIRMEC sous une charge axiale de traction, dans un sol fin non cohésif, a montré le développement d’une surface cylindrique de rupture. Celle-ci ne dépend pas de la configuration géométrique des pieux tel que : l’espacement S, le diamètre d’hélice Dh et le diamètre du tube d. En adoptant ce critère de rupture et à l’aide d’une analyse statistique des données, nous avons proposé quatre méthodes analytiques de prédiction de la capacité portante des pieux SPIRMEC à partir des essais in-situ et au laboratoire qui sont: •Méthode CPT basée sur la résistance de pointe pénétromètrique (essai CPT), •Méthode MPT basée sur la pression limite pressiomètrique (essai MPT), •Méthode du couple d’installation, •Méthode analytique basée sur les paramètres de cisaillement de sol notamment l’angle de frottement interne (essais triaxial et boîte de cisaillement). Ces méthodes tiennent compte de la géométrie du pieu, du procédé de mise en oeuvre et de la compacité du sol. L’analyse de performance des méthodes proposées a montré que les méthodes analytique et CPT représentent mieux le comportement des pieux testés. La modélisation numérique du comportement des pieux SPIRMEC sous charge axiale de traction a été également étudiée à l’aide du code de calcul Plaxis 2D. Un modèle axisymétrique a été adopté pour modéliser la géométrie de la structure. Le modèle de comportement hardening soil a été retenu pour modéliser le comportement élastoplastiq des couches de sol. Un modèle élastique linéaire a été retenu pour le pieu. Quant au comportement de l’interface sol-structure, il a été pris en compte par un modèle élastoplastique basé sur les critères de Mohr-Coulomb. L’expansion du sol résultant de l’installation des pieux a été approchée par une cavité cylindrique. Cette dernière a été modélisée par des déformations volumiques anisotropes. Nous avons constaté, qu’appliquer une déformation volumique de l’ordre de 40% permet une bonne concordance entre les résultats numériques et expérimentaux. L’étude paramétrique nous a également permis de constater l’existence d’une variation linéaire entre la capacité portante et l’espacement S. Le comportement de l’acier galvanisé dans le sol a été également étudié au moyen de trois approches: électrochimique, visuelles grâce au microscope électronique et gravimétrique. Les tests électrochimiques de corrosion du zinc ont été réalisés dans la solution de sol artificielle pour deux périodes bien distinctes : saison des pluies et après 8 mois de contact sol-pieu. Une forte dépendance est constatée de la vitesse de corrosion de zinc au pH et à la conductivité de la solution. La vitesse de corrosion est plus importante en saison des pluies qu’après 8 mois de contact de pieu avec le sol. Les fortes concentrations en sulfates semblent augmenter la vitesse de corrosion. Les analyses menées au MEB montrent que la zone de fluctuation de nappe et en surface externe (sol/air) sont les zones les plus corrodées. La comparaison entre les différentes techniques d’évaluation de la vitesse de corrosion a montré que l’eau de nappe peut être utilisée comme un milieu représentatif du profil chimique d’un sol non cohésif et légèrement granulaire.
The purpose of this thesis is to study the both behaviors mechanical and of the corrosion of a new foundation system, called spirec piles, for lightweight structures. The work was based on two main aspects. The first aspect concerns the analysis of behavior of the spirmec piles under axial loading on the basis of experimental and numerical modeling in a non-cohesive soft soil. On the second aspect, it addresses the problem of corrosion of steel forming the pile in a humid tropical environment. The behavior of the tested piles under axial traction load, in a non-cohesive soil, showed the development of a cylindrical surface of failure. This does not depend on the geometrical configuration of the tested piles such that: the spacing s, the helix diameter dh and the diameter of the shaft. By adopting this failure criterion and using statistical data analysis, we proposed four analytical methods for predicting the bearing capacity of the piles from in-situ and laboratory tests, which are: cpt method based on tip resistance penetrometer (cpt test), mpt method based on pressuremeter limit pressure (test mpt), method of installation torque and analytical method based on the shear parameters of soil (triaxial tests and shear box). These methods take into account the geometry of the pile, the method and implementation of soil compaction. Performance analysis of the proposed methods showed that the analytical methods and cpt represent better the behavior of piles tested. An axisymmetric condition was assumed to model this geometry in two-dimensional space. In this study, we proposed to model the pipe screw pile with plates elements available in plaxis 2d. The helixes were modeled as circular disks. Interface elements were incorporated along the pile to simulate the soil-pile interaction. Hardening soil model was chosen to describe the soil with drained behavior was assigned for all layers. Linear elastic for pile and elastic plastic model based on the mohr-coulomb criterion was used to describe the interface behavior. The lateral expansion generated by the pile shaft was modeled by anisotropic volumetric strains (ɛxx=ɛzz, ɛyy=0). The pile behavior under tensile loading at different volumetric strains, it is clear that the best fit was obtained at volumetric strain of 40%. The parametric study also allowed us to establish the existence of a linear variation between the bearing capacity and spacings. The behavior of the galvanized steel in the ground has also been studied using three approaches such as: electrochemical, microscopic imaging and gravimetrically. Electrochemical tests of the corrosion of the zinc have been made in artificial soil solution into two periods, the rainy season and after eight months of contact soil-pile. Is a strong dependence of the observed corrosion rate of the zinc at the ph and conductivity of the solution. The corrosion rate is higher in the rainy season compared to eight months of contact of the pile with soil. High sulfate concentrations increase the rate of corrosion. The meb analysis shows that the fluctuation zone of the water table is the most corroded area. Comparison between the different methods of evaluating the corrosion rate showed that the ground water may be used as a representative profile of the chemical environment of a non-cohesive soil and slightly granular.

http://www.theses.fr/2014AGUY0790/document

Éditeur(s) : Elsevier
Résumé : The main feature of the Congo-Angola margin in the Gulf of Guinea is the Congo (ex-Zaire) deep-sea fan composed of a submarine canyon directly connected to the Congo River, a channel and a [sediment] lobe area. During the multi-disciplinary programme called BIOZAIRE conducted by Ifremer from 2000 to 2005, two CTD-O2 sections with discrete water column samples were performed (BIOZAIRE3 cruise: 2003-2004) to study the influence of the Congo River discharges, both in the surface layer and in the deep and near-bottom layers. The surface layer water is greatly diluted with river water that has a heavy particle load. The deep layer is affected by episodic turbidity currents that flow in the deep Congo channel and reach deep areas far from the coast. Previous studies revealed deep anomalies in oxygen (deficit) and nutrient (excess) concentrations at not, vert, similar4000 m depth and assumed that they resulted from mineralisation of the particulate organic matter from the Congo River. The BIOZAIRE3 sections were designed to explore these phenomena in more detail near the Congo channel. Oxygen and nutrients were measured as well as additional parameters, including stable isotopes of oxygen and carbon, dissolved inorganic carbon and pH. For the surface layer, the effect of the Congo River was studied with reference to salinity. Deviations from the theoretical dilution of various inorganic solutes suggested the occurrence of mineralisation and consumption processes. For the deep layer, the network of CTD-O2 stations gave a more detailed description of the deep anomalies than in previous studies. From the east-west section, anomalies appeared on the bottom at 4000 m depth and became slightly shallower when they spread to the west. They were also present north and south on the bottom along the 4000 m isobath. In these deep waters, the decrease in the o13C values of dissolved inorganic carbon confirmed that the mineralisation of organic matter plays a role in generating these anomalies. The location of the origin of this deep anomaly is debated. Here, arguments are given in favour of mineralisation of the particulate organic matter input that overflows from the Congo channel at not, vert, similar4000 m depth during turbidity current events. Other authors suggest that this input comes from downslope particle transport. Anomalies of the same origin, but weaker, also occurred deeper on the Congo lobe, where the Congo channel ends, but with a significant pH decrease on the bottom which was not seen at 4000 m depth.
Deep Sea Research Part II: Topical Studies in Oceanography (0967-0645) (Elsevier), 2009-11 , Vol. 56 , N. 23 , P. 2183-2196

Droits : 2009 Elsevier Ltd All rights reserved.
http://archimer.ifremer.fr/doc/2009/publication-6737.pdf
DOI:10.1016/j.dsr2.2009.04.002
http://archimer.ifremer.fr/doc/00000/6737/

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Though the root biomass of tropical rainforest trees is concentrated in the upper soil layers, soil water uptake by deep roots has been shown to contribute to tree transpiration. A precise evaluation of the relationship between tree dimensions and depth of water uptake would be useful in tree-based modelling approaches designed to anticipate the response of tropical rainforest ecosystems to future changes in environmental conditions. We used an innovative dual-isotope labelling approach (deuterium in surface soil and oxygen at 120-cm depth) coupled with a modelling approach to investigate the role of tree dimensions in soil water uptake in a tropical rainforest exposed to seasonal drought. We studied 65 trees of varying diameter and height and with a wide range of predawn leaf water potential (I-pd) values. We confirmed that about half of the studied trees relied on soil water below 100-cm depth during dry periods. I-pd was negatively correlated with depth of water extraction and can be taken as a rough proxy of this depth. Some trees showed considerable plasticity in their depth of water uptake, exhibiting an efficient adaptive strategy for water and nutrient resource acquisition. We did not find a strong relationship between tree dimensions and depth of water uptake. While tall trees preferentially extract water from layers below 100-cm depth, shorter trees show broad variations in mean depth of water uptake. This precludes the use of tree dimensions to parameterize functional models.
ISSN: 0029-8549

hal-01032433
https://hal.archives-ouvertes.fr/hal-01032433
DOI : 10.1007/s00442-013-2724-6