Éditeur(s) : HAL CCSD
Résumé : International audience
Trees can control their shape and resist gravity thanks to their ability to produce wood under tensile stress. This stress is known to be produced during the maturation of wood fibres but the mechanism of its generation remains unclear. This study focuses on the formation of the secondary wall in tension wood produced in artificially tilted poplar saplings. Thickness of secondary wall layer (SL) and gelatinous layer (GL) were measured from cambium to mature wood in several trees sampled at different times after tilting. Measurements on wood fibres produced before tilting show the progressive increase of secondary wall thickness during the growing season. After the tilting date, SL thickness decreased markedly from normal wood to tension wood while the total thickness increased compared to normal wood, with the development of a thick GL. However, even after GL formation, SL thickness continues to increase during the growing season. GL thickening was observed to be faster than SL thickening. The development of the unlignified GL is proposed to be a low cost, efficient strategy for a fast generation of tensile stress in broadleaved trees.
IAWA journal / International Association of Wood Anatomists.

hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277/document
https://hal.archives-ouvertes.fr/hal-01229277/file/AbediniClair-Iawa-TensionCellWallThickening_preprint_HAL.pdf
DOI : 10.1163/22941932-00000084

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Tension wood of Laetia procera (Poepp.) Eichl. (Flacourtiaceae), a neo-tropical forest species, shows a peculiar secondary wall structure, with an alternance of thick and thin layers, while opposite wood of this species has a typical secondary wall structure (S1 + S2 + S3). Samples for the study of microstructural properties were collected upon the estimation of growth stresses in the living tree, in order to analyze the correlation of the former with the latter. Investigation using optical microscopy, scanning electron microscopy and UV microspectrophotometry allowed the description of the anatomy, ultra-structure and chemistry of this peculiar polylaminate secondary wall. In the thick layers, cellulose microfibril angle is very low (i.e., microfibril orientation is close to fibre axis) and cellulose microfibrils are well organized and parallel to each other. In the thin layers, microfibrils (only observable in the inner layer) are less organized and are oriented with a large angle relative to the axis of the cell. Thick layers are lightly lignified although thin layers show a higher content of lignin, close to that of opposite wood secondary wall. The more the wood was under tensile stress, the less the secondary wall was lignified, and lower the syringyl on guaiacyl lignin units' ratio was. The innermost layer of the secondary wall looks like a typical S3 layer with large microfibril angle and lignin occurrence. The interest of this kind of structure for the understanding of stress generation is discussed.
ISSN: 0931-1890

hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923
https://hal.archives-ouvertes.fr/hal-00194923/document
https://hal.archives-ouvertes.fr/hal-00194923/file/Trees_RuelleYoshidaClairThibaut_submitted2006.pdf
DOI : 10.1007/s00468-007-0128-0

Éditeur(s) : HAL CCSD
Résumé :  
Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rain forest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood, and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-01032051
https://hal.archives-ouvertes.fr/hal-01032051

Éditeur(s) : HAL CCSD
Résumé : International audience
A key element of the biomechanical design of trees is their ability to generate largemechanical stresses in wood at the stem periphery. This function is necessary for the tree tocontrol the orientation of its axes, and therefore to grow in height, maintain its branches at anoptimal angle or achieve adaptive reorientations (Fournier et al., 2013). This “maturationstress” appears in wood fibres during their cellular maturation when their secondary cell wallis thickening. In hardwoods, the stress asymmetry is generated by the formation of specificfibres with a very high tensile growth stress on the upper side of the inclined axis. Theresulting tension wood has microstructural features highly different from the normal wood.Tension wood in almost all temperate species has a specific gelatinous cell wall layer, calledG-layer, that is not lignified and highly mesoporous (Chang et al., 2015). It has been shownrecently, at the macroscopic scale, that cellulose tension appears during maturation and issynchronous with the development of this specific layer (Clair et al., 2011). Tropical species,like simarouba, are able to generate lignified tension wood fibres. The mechanisms of stressgeneration in tension wood fibres are not yet well known. The aim of our study is tounderstand these mechanisms and to know the spatial and temporal kinetics of the differentcell wall layers stiffening during maturation, in parallel with tensile stress generation.Contact-Resonance Atomic Force Microscopy, CR-AFM, was used here to address thisquestion on embedded samples (Arnould and Arinero, 2015) using dual resonance frequencytracking (DRFT, Rodriguez et al., 2007). Change in the contact modulus between, and within,each layer of the cell wall has been measured on several radial lines of developing fibres atdifferent steps. In order to understand the obtained results, and to estimate the sensitivity ofthe AFM indentation-like technique to the different cell wall components stiffness, an elasticanisotropic indentation model was used (Vlassak et al., 2003; Jäger et al., 2011). Finally,these mechanical measurements have been compared to topochemical data obtained on thesame fibres.
8th Plant Biomechanics International Conference
Nagoya, Japan

hal-01436113
https://hal.archives-ouvertes.fr/hal-01436113

Éditeur(s) : HAL CCSD
Résumé : Wood samples were taken from the upper and lower sides of 21 naturally tilted trees from 18 families of angiosperms in the tropical rainforest in French Guyana. The measurement of growth stresses ensured that the two samples were taken from wood tissues in a different mechanical state: highly tensile stressed wood on the upper side, called tension wood and lower tensile stressed wood on the lower side, called opposite wood. Eight species had tension wood fibres with a distinct gelatinous layer (G-layer). The distribution of gelatinous fibres varied from species to species. One of the species, Casearia javitensis (Flacourtiaceae), showed a peculiar multilayered secondary wall in its reaction wood. Comparison between the stress level and the occurrence of the G-layer indicates that the G-layer is not a key factor in the production of high tensile stressed wood.
IAWA Journal

hal-00112579
https://hal.archives-ouvertes.fr/hal-00112579
https://hal.archives-ouvertes.fr/hal-00112579/document
https://hal.archives-ouvertes.fr/hal-00112579/file/IAWA2006_ClairRuelleBeauchenePrevostFournier_ccsd.pdf
IRD : PAR00001136

Éditeur(s) : HAL CCSD North Carolina State University
Résumé : Few studies have been conducted about relation between cellulose parameters and biomechanical properties of wood in tropical angiosperms species. For this purpose, on 13 trees from 3 species of French Guyana tropical rainforest in a clear active process of restoring verticality, i) growth strains were measured in situ in order to determine the occurrence of tension wood within samples and ii) cellulose structural parameters were estimated on all the samples using X-ray diffraction method. Crystallite size was estimated from the full-width at half-maximum of the Miller index (002) arc diffraction and angle T was measured following Cave's method. Relationships between these parameters and growth stresses were good and the variations between normal and tension wood were significant, i.e. a lower angle T and a larger crystallite size in tension wood. In order to have a good estimation of the microfibril angle in the main layer of the secondary wall for each species, an experimental calibration was done between angle T and microfibril angle observed with scanning electron microscopy.
ISSN: 19302126

hal-01031799
https://hal.archives-ouvertes.fr/hal-01031799
https://hal.archives-ouvertes.fr/hal-01031799/document
https://hal.archives-ouvertes.fr/hal-01031799/file/42-575-1-PB.pdf