Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
Reaction wood produces very peculiar maturation stresses at the tree periphery i.e. compressive stress or very high tensile stress, for compression and tension wood respectively, as compared to moderately high tensile stress for normal wood. This means that both its mechanical state and its mechanical and physical properties differ from normal wood. Compression wood shows big differences from normal wood in conifers, for all physical and mechanical properties: higher density and axial crushing strength (MOR) but lower modulus of elasticity (MOE), far higher axial (longitudinal) shrinkage but lower radial and tangential shrinkage, sometimes even lower than the axial shrinkage. For tension wood things are less simple and can vary a lot from hardwood species to species. Globally there are no systematic differences in density and transverse shrinkage, MOE tends to be a little higher while MOR is slightly lower. However, axial shrinkage is much higher for tension wood with a gelatinous layer (G layer) than normal wood due to the specific gel like organization of cellulose microfibrils in the G layer. For tension wood without a G layer(which is rather frequent) axial shrinkage in the first drying operation is around two times higher than in normal wood mainly because of a kind of hygro-thermal release of locked in maturation stress. Overall the very high tensile stress and stored elastic energy in tension wood lead to problemsin wood processing (end splitting and board warping), which is far less the case for compression wood. But due to the large difference in properties relative to normal wood, compression wood occurrence is always a big problem for the in service behaviour of timber, which is seldom the case for tension wood.
The biology of reaction wood

ISBN : 978-3-642-10813-6
hal-01135273
https://hal.archives-ouvertes.fr/hal-01135273

Éditeur(s) : HAL CCSD Springer-Verlag Berlin Heidelberg
Résumé : International audience
The main biological function of reaction wood is to act as " muscle " for trees, enabling them to control their posture. The key property to achieve this function is the development of high mechanical stress during the formation of reaction wood cells, called " maturation strains ". Actually, reaction wood formation is basically the asymmetric formation of wood around the tree circumference, with higher maturation strains on the side where reaction wood is formed than on the opposite side. This asymmetry enables stems to bend upward or to compensate for the downward bending induced by gravity. At the cross section level, the performance in this biological function is linked not only to the magnitude of this asymmetry but also to an effect of the cross-sectional size (diameter) of the stem. Eccentric growth and variations in wood mechanical stiffness are second order effects that can modify this performance. Differences in maturation strains between reaction and non-reaction woods are related to their specific cell wall structure and composition. The swelling of the cell wall matrix during maturation and the effect of microfibril angle explain the differences in maturation strains between normal and compression wood. However, this mechanism fails in explaining the high maturation shrinkage of tension wood, and several hypotheses at the molecular levels are still under debate. How trees perceive their gravitational disequilibrium is also an open question for physiologists. Integrative biomechanical modelling (from the polymer level to the cell wall, cross section and whole tree levels) enables defining key variables that explain the performance of reaction wood as a system that insures the stem motricity. Maturation strains can be precisely measured only in recently formed wood at the tree surface, but their changes during the whole tree life can also be estimated by retrospective dendrochronological analysis through structural markers of reaction wood. Lastly, wood in living trees ensures general storage, defence, vascular and skeletal functions, that ask general questions about synergies and trade-offs as the structural characteristics of reaction wood can affect all these functions.
The Biology of Reaction Wood

ISBN : 978-3-642-10813-6
hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085
https://hal.archives-ouvertes.fr/hal-01452085/document
https://hal.archives-ouvertes.fr/hal-01452085/file/Chap_Gril_al_Biomechanical_action_biological_functions_2014.pdf

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
This study aims at better understanding the respective influences of specific gravity (γ), microfibril angle (MFA), and cell-wall matrix polymers on viscoelastic vibrational properties of wood in axial direction. The wide variations of properties between normal wood (NW) and compression wood (CW) are in focus. Three young bent trees (Picea abies, Pinus sylvestris and Pinus pinaster) that recovered verticality were sampled. Several observed differences between NW and CW were highly significant in terms of anatomical, physical (γ, shrinkage, CIELab colorimetry), mechanical (compressive strength), and vibrational properties. Specific dynamic modulus of elasticity (E'/γ) decreases with increasing MFA, and Young's modulus (E') can be satisfactorily explained by γ and MFA. Apparently, the type of the cell wall polymer matrix is not influential in this regard. The damping coefficient (tanδ) does not depend solely on MFA of NW and CW. The tanδ - E'/γ relationship evidences that, at equivalent E'/γ, the tanδ of CW is approx. 34% lower than that of NW. This observation is ascribed to the more condensed nature of CW lignins, and this is discussed in the context of previous findings in other hygrothermal and time/frequency domains. It is proposed that the lignin structure and the amount and type of extractives, which are both different in various species, are partly responsible for taxonomy-related damping characteristics.
ISSN: 0018-3830

hal-00808062
https://hal.archives-ouvertes.fr/hal-00808062
https://hal.archives-ouvertes.fr/hal-00808062/document
https://hal.archives-ouvertes.fr/hal-00808062/file/Changes_viscoelastic_vibrational_Bremaud_al.pdf
DOI : 10.1515/hf-2011-0186

Éditeur(s) : HAL CCSD Springer Verlag
Résumé :  
Growth strains were measured in situ in nine trees of three species from a French Guiana tropical rainforest in a clearly active verticality restoration process. The aim was to detect tension wood within the samples. Wood specimens were cut in the vicinity of the growth strain measurements in order to determine the microfibril angle and some mechanical and physical properties. As suspected, tensile growth strain was much higher in tension wood zones, as shown by the slightly higher longitudinal modulus of elasticity. Conversely, tension wood showed reduced compression strength. Longitudinal shrinkage was much higher in tension wood than in opposite wood. Clear relationships between the microfibril angle and longitudinal properties were noted in comparison (i) with those observed in gymnosperm compression wood and (ii) with expected relationships from the organization of wood fibres cell wall structure.
ISSN: 0043-7719

hal-01032114
https://hal.archives-ouvertes.fr/hal-01032114
DOI : 10.1007/s00226-010-0323-9

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Active mechanisms of re-orientation are necessary to maintain the verticality of tree stems. They are achieved through the production of reaction wood, associated with circumferential variations of three factors related to cambial activity: maturation strain, longitudinal modulus of elasticity (MOE) and eccentric growth. These factors were measured on 17 mature trees from different botanical families and geographical locations. Various patterns of circumferential variation of these factors were identified. A biomechanical analysis based on beam theory was performed to quantify the individual impact of each factor. The main factor of re-orientation is the circumferential variation of maturation strains. However, this factor alone explains only 57% of the re-orientations. Other factors also have an effect through their interaction with maturation strains. Eccentric growth is generally associated with heterogeneity of maturation strains, and has an important complementary role, by increasing the width of wood with high maturation strain. Without this factor, the efficiency of re-orientations would be reduced by 31% for angiosperms and 26% for gymnosperms. In the case of angiosperms, MOE is often larger in tension wood than in normal wood. Without these variations, the efficiency of re-orientations would be reduced by 13%. In the case of gymnosperm trees, MOE of compression wood is lower than that of normal wood, so that re-orientation efficiency would be increased by 24% without this factor of variations.
ISSN: 0931-1890

hal-01031825
https://hal.archives-ouvertes.fr/hal-01031825
DOI : 10.1007/s00468-005-0407-6

Éditeur(s) : HAL CCSD Royal Society
Résumé : International audience
Trees control their posture by generating asymmetric mechanical stress around the periphery of the trunk or branches. This stress is produced in wood during the maturation of the cell wall. When the need for reaction is high, it is accompanied by strong changes in cell organization and composition called reaction wood, namely compression wood in gymnosperms and tension wood in angiosperms. The process by which stress is generated in the cell wall during its formation is not yet known, and various hypothetical mechanisms have been proposed in the literature. Here we aim at discriminating between these models. First, we summarize current knowledge about reaction wood structure, state and behaviour relevant to the understanding of maturation stress generation. Then, the mechanisms proposed in the literature are listed and discussed in order to identify which can be rejected based on their inconsistency with current knowledge at the frontier between plant science and mechanical engineering.
Journal of the Royal Society Interface

hal-01392832
https://hal.archives-ouvertes.fr/hal-01392832
https://hal.archives-ouvertes.fr/hal-01392832/document
https://hal.archives-ouvertes.fr/hal-01392832/file/AlmerasClair2016_JRSInterface_Critical%20review%20on%20the%20mechanisms%20of%20maturation%20stress%20generation%20in%20trees_HAL.pdf
DOI : 10.1098/rsif.2016.0550

Éditeur(s) : HAL CCSD Springer Verlag (Germany)
Résumé : International audience
*Context: Tree orientation is controlled by asymmetric mechanical stresses set during wood maturation. The magnitude of maturation stress differs between longitudinal and tangential directions, and between normal and tension woods. * Aims: We aimed at evaluating patterns of maturation stress on eucalypt plantation trees and their relation with growth, with a focus on tangential stress evaluation. * Methods: Released maturation strains along longitudinal and tangential directions were measured around the circumference of 29 Eucalyptus nitens trees, including both straight and leaning trees. * Results: Most trees produced asymmetric patterns of longitudinal maturation strain but more than half of the maturation strain variability occurred between trees. Many trees produced high longitudinal tensile stress all around their circumference. High longitudinal tensile stress was not systematically associated with the presence of gelatinous layer. The average magnitude of released longitudinal maturation strain was found negatively correlated to the growth rate. A methodology is proposed to ensure reliable evaluation of released maturation strain in both longitudinal and tangential directions. Tangential strain evaluated with this method was lower than previously reported. * Conclusion: The stress was always tensile along longitudinal direction and compressive along tangential direction, and their respective magnitude was positively correlated. This correlation does not result from a Poisson effect but may be related to the mechanism of maturation stress generation.
Annals of Forest Science

hal-00913611
https://hal.archives-ouvertes.fr/hal-00913611
https://hal.archives-ouvertes.fr/hal-00913611/document
DOI : 10.1007/s13595-013-0318-4

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : A hypothetical mechanism for the generation of maturation stress in wood was tested experimentally. The hypothesis was that the maturation stress could partly originate in a physical mechanism related to daily changes in water pressure and associated diurnal strains. The matrix of lignin and hemicellulose, deposited in the cell wall during the night, would be put in compression by the effect of water tension during the next day. The cellulose framework, crystallizing during the day, would be put in tension by the decrease in tension at night and subsequent cell-wall swelling. This was tested on young saplings of sugi and beech. Half of the saplings were submitted to continuous lighting, which canceled diurnal strains. Saplings were tilted 40 degrees, and their uprighting movement was measured. The uprighting movement is directly due to the production of reaction wood and the concomitant development of large longitudinal maturation stress. It occurred in the continuously lighted plants at least as much as in control plants. We conclude that the generation of longitudinal maturation stress in tension or compression wood is not directly related to variations in water pressure and diurnal strains.
ISSN: 1435-0211

hal-01031891
https://hal.archives-ouvertes.fr/hal-01031891
DOI : 10.1007/s10086-005-0788-6