Éditeur(s) : HAL CCSD E Schweizerbart Science Publishers
Résumé : International audience
We present an electron tomography study of dislocations in deformed olivine single crystals, at ca. 0.5 T m, along two distinct orientations. The easiest slip systems are [001](100) and [001]{110}. Disorientating a single crystal away from easy glide conditions leads to massive cross-slip, which generates three-dimensional dislocations, and thus contributes to hardening. Fast motion of curved non-screw dislocation in those planes leaves long straight screw dislocations which bear lattice friction and control plastic strain. We have identified several hardening mechanisms. Non-screw [001] dislocations interact elastically to form dipoles. Recovery mechanisms leading to dipole annihilation are observed, but they are slow at those temperatures and produce numerous sessile loops. These loops represent obstacles for gliding dislocations. Interactions between dislocations and sessile loops produce sessile segments (super jogs), which efficiently impede dislocation motions.
ISSN: 0935-1221

hal-01277821
https://hal.archives-ouvertes.fr/hal-01277821
DOI : 10.1127/ejm/2015/0027-2481

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Transmission electron microscopy observations on olivine crystals deformed at moderate (≤1273 K) temperature evidenced dislocations interactions explaining the hardening observed in the experiments, but also recovery mechanisms by the absorption or emission of point defects. Thus we investigate the possibility that, at geological strain-rates, these recovery processes allow steady-state deformation by dislocation creep at low to moderate temperatures in the lithospheric mantle. We test this hypothesis using a 2.5-D dislocation dynamics (DD) model, which combines dislocation glide and recovery by climb. This model shows that diffusion-controlled recovery processes allow for steady-state deformation by dislocation creep in the lithospheric mantle at stresses <500 MPa. For stresses of 50–200 MPa, steady-state strain-rates of 10−15 s−110−15 s−1 may be attained at temperatures as low as 900 K. Fitting of the DD model produces a flow law, which represents a lower bound for the lithospheric mantle strength, since the models describe the deformation of an olivine single crystal in an easy slip orientation. Comparison of strain-rates and Moho temperatures inferred for different geodynamic environments and the predictions of this model-based flow law implies, nevertheless, that, except in incipient rifts, most of the observed deformation may be produced by stress levels ≤200 MPa, consistent with those inferred to be produced by convection. This convergence suggests that the present models, which explicitly calculate the time-dependent dislocation dynamics, may provide a correct first order estimate of the mechanical behaviour of the lithospheric mantle, which cannot be derived directly from any existing data.
ISSN: 0012-821X

hal-01277178
https://hal.archives-ouvertes.fr/hal-01277178
https://hal.archives-ouvertes.fr/hal-01277178/document
https://hal.archives-ouvertes.fr/hal-01277178/file/Boioli.pdf
DOI : 10.1016/j.epsl.2015.10.012

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We have performed tri-axial compression experiments on olivine aggregates at 900 °C and at a confining pressure of 300 MPa in a high-resolution gas-medium mechanical testing apparatus. Deformation at two different constant strain rates (1.1 × 10− 5 s− 1 and 3.4 × 10− 4 s− 1) yields continuous hardening, reaching maximal differential stresses of 930 and 1076 MPa, respectively, before sample failure at ca. 10% strain. The deformed samples were characterized by electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). Crystallographic preferred orientations (CPO) are weak but reveal an alignment of the [010] axes around the compression direction and some concentration of [001] and [100] axes normal to it. TEM observations confirm plastic deformation by dislocation glide, with both [001] and [100] Burgers vectors. Electron tomography, performed for the first time on deformed fined-grained olivine, shows that [001] dislocations glide extensively on {110} and {130} planes, in complement to the (010) and (100) glide planes often reported at high temperatures. [100] dislocations glide mostly on (010), but {011} and {041} planes are also activated. The experimental CPO and relative activity of slip systems are well reproduced by viscoplastic self-consistent simulations in which all [100] and [001] slip systems have similar strengths. They are also consistent with olivine CPO from natural samples deformed at low temperature. Comparison of the present mechanical results to those obtained for olivine single-crystals at similar conditions shows that at low temperature (below 1100 °C) and high stress (> 300 MPa) polycrystalline olivine has a more complex mechanical behavior than single crystals. However, both datasets advocate for a much weaker dry mantle lithosphere than previously thought.
ISSN: 0040-1951

hal-01053513
https://hal.archives-ouvertes.fr/hal-01053513
DOI : 10.1016/j.tecto.2014.03.022

Éditeur(s) : HAL CCSD Taylor & Francis
Résumé : The diamond anvil cell (DAC) is a fundamental device used to explore the properties of materials under extreme pressure and temperature (P/T) conditions. In the past years, simultaneous high P/T DAC experiments using the resistively heated DAC (RH-DAC) techniques have been developed for studying materials properties in a wide P/T range. However, the mechanical instability of metallic gaskets used for sample confinement at high P/T conditions remains a limiting factor for exploiting the accessible P/T range of the RH-DAC. In this study, we present a new gasket configuration that overcomes these limitations. It is based on an amorphous boron-epoxy mixture inserted in a rhenium gasket. We show how these gasket inserts stabilize the sample chamber over a wide P/T range, allowing monitoring sample properties using X-ray diffraction and absorption spectroscopy up to 50GPa and 1620K.
ISSN: 0895-7959

hal-01608425
https://hal.archives-ouvertes.fr/hal-01608425
DOI : 10.1080/08957959.2016.1245297
PRODINRA : 387347

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
A San Carlos olivine polycrystal has been deformed under uppermost mantle conditions, by compression at 900 °C, at a strain rate of 1.1 × 10−5 s−1, under a confining pressure of 300 MPa, using the Paterson press. Transmission electron tomography of dislocations has been performed by scanning transmission electron microscopy, by conventional transmission electron microscopy using the weak-beam dark-field technique, associated with precession or not, in order to determine the glide planes of [001] screw dislocations. This recent technique is the most suitable one since most [001] dislocations exhibit straight screw segments due to the high lattice friction on this character at low temperature. We find that [001] dislocations glide in (100), (010) and {110} as already reported, but also more unexpectedly in {120} and {130}. We show that at 900 °C, [001] {110} glide is dominant in polycrystals. We have, however, noted and characterized numerous cross-slip events in the specimen.
ISSN: 0342-1791

hal-01054330
https://hal.archives-ouvertes.fr/hal-01054330
DOI : 10.1007/s00269-014-0665-1

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Mantle noble gases record important and ancient isotopic heterogeneities, which fundamentally influence our understanding of mantle geodynamics, yet these heterogeneities are difficult to fully interpret without understanding the basic mechanisms of noble gas storage and transport in mantle minerals. A series of annealing experiments that mimic mantle conditions (i.e. sub-solidus with natural, polycrystalline, texturally equilibrated olivines at low noble gas partial pressures) show that intergranular interfaces (grain boundaries) are major hosts for noble gases in the mantle, and that interfaces can dramatically fractionate noble gases from their radio-parents (U + Th and K). Therefore, noble gas isotopic heterogeneities in the mantle could result from grain size variations. Fine-grained lithologies (mylonites and ultramylonites, for example) with more grain boundaries will have lower U/3He ratios (compared to a coarse grained equivalent), which, over time, will preserve higher 3He/4He ratios. As predicted by theory of points defect diffusivity, these results show that noble gas diffusion along interfaces is different from those in the grain lattice itself at low temperatures. However, for grain size relevant of the Earth's mantle, the resulting effective correlated activation energies (Ea)(Ea) and pre-exponential factors (Do/a2)(Do/a2) produce similar diffusivities at mantle temperatures for interface- and lattice-hosted helium. Therefore, grain boundaries do not significantly affect helium transport at mantle conditions and length scales.
ISSN: 0012-821X

hal-01236013
https://hal.archives-ouvertes.fr/hal-01236013
DOI : 10.1016/j.epsl.2015.08.024

Éditeur(s) : HAL CCSD Mineralogical Society of America
Résumé : International audience
To test if hydrogen incorporation by ionic diffusion can occur between a volatile-rich kimberlitic liquid and forsterite, results of high-pressure and high-temperature experiments using a piston-cylinder apparatus at 1200–1300 °C and 1 GPa for durations of 1 min, 5 h, and 23 h, are reported here. Kimberlitic liquid in the system CaO-MgO-Al2O3-SiO2-CO2-H2O and synthetic forsterite single crystals were chosen as a first simplification of the complex natural kimberlite composition. Unpolarized Fourier transform infrared spectroscopy was used to quantify the concentrations of OH in the crystallographically oriented forsterite. Scanning electron microscopy, electron backscattered diffraction, electron microprobe analyses, and transmission electron microscopy were performed to identify the run products. After 5 and 23 h, a forsterite overgrowth crystallized with the same orientation as the initial forsterite single crystal. The kimberlitic liquid has crystallized as micrometer-scale euhedral forsterite neocrystals with random crystallographic orientations, as well as a nanoscale aluminous phase and a calcic phase. Despite theoretical water-saturation of the system and long duration, none of the initial forsterite single crystals display signs of hydration such as hydrogen diffusion profile from the border toward the center of the crystal. Most likely, the presence of CO2 in the system has lowered the H2O fugacity to such an extent that there is no significant hydration of the starting forsterite single crystal or its overgrowth. Also, the presence of CO2 enhances rapid forsterite crystal growth. Forsterite growth rate is around 2 × 108 μm3/h at 1250 °C. These experimental results suggest a deep mantle origin of the high OH content found in natural mantle-derived xenoliths transported in kimberlites, as reported from the Kaapvaal craton. In agreement with previous studies, it also points out to the fact that significant hydration must take place in a CO2-poor environment.
ISSN: 0003-004X

hal-01217157
https://hal.archives-ouvertes.fr/hal-01217157
DOI : 10.2138/am-2015-5200

Éditeur(s) : HAL CCSD Taylor & Francis: STM, Behavioural Science and Public Health Titles
Résumé : International audience
The dislocation microstructures in a single crystal of olivine deformed experimentally in uniaxial compression at 1090 °C and under a confining pressure of 300 MPa, have been investigated by transmission electron tomography in order to better understand deformation mechanisms at the microscale relevant for lithospheric mantle deformations. Investigation by electron tomography reveals microstructures, which are more complex than previously described, composed of and dislocations commonly exhibiting 3D configurations. Numerous mechanisms such as climb, cross-slip, double cross-slip as well as interactions like junction formations and collinear annihilations are the source of this complexity. The diversity observed advocates for microscale deformation of olivine significantly less simple than classic dislocation creep reported in metals or ice close to melting temperature. Deciphering mechanism of hardening in olivine at temperatures where ionic diffusion is slow and is then expected to play very little role is crucial to better understand and thus model deformation at larger scale and at temperatures (900–1100 °C) highly relevant for the lithospheric mantle.
ISSN: 1478-6443

hal-01667146
https://hal.archives-ouvertes.fr/hal-01667146
DOI : 10.1080/14786435.2017.1367858

Éditeur(s) : HAL CCSD Nature Publishing Group
Résumé : International audience
Mantle flow involves large strains of polymineral aggregates. The strongly anisotropic plastic response of each individual grain in the aggregate results from the interactions between neighbouring grains and the continuity of material displacement across the grain boundaries. Orthorhombic olivine, which is the dominant mineral phase of the Earth's upper mantle, does not exhibit enough slip systems to accommodate a general deformation state by intracrystalline slip without inducing damage. Here we show that a more general description of the deformation process that includes the motion of rotational defects referred to as disclinations can solve the olivine deformation paradox. We use high-resolution electron backscattering diffraction (EBSD) maps of deformed olivine aggregates to resolve the disclinations. The disclinations are found to decorate grain boundaries in olivine samples deformed experimentally and in nature. We present a disclination-based model of a high-angle tilt boundary in olivine, which demonstrates that an applied shear induces grain-boundary migration through disclination motion. This new approach clarifies grain-boundary-mediated plasticity in polycrystalline aggregates. By providing the missing mechanism for describing plastic flow in olivine, this work will permit multiscale modelling of the rheology of the upper mantle, from the atomic scale to the scale of the flow.
ISSN: 0028-0836

hal-01054315
https://hal.archives-ouvertes.fr/hal-01054315
DOI : 10.1038/nature13043

Éditeur(s) : HAL CCSD Taylor & Francis: STM Behavioural Science and Public Health Titles Taylor & Francis: STM, Behavioural Science and Public Health Titles
Résumé : We have investigated by electron tomography, in a transmission electronic microscope, the interactions between dislocations in olivine single crystals and polycrystals deformed in axial compression at T < 1000 °C (T < 0.5Tm). Dislocations are mostly of the [0 0 1] type, except in the polycrystal where [1 0 0] and [0 0 1] dislocations have been activated. A few 〈1 0 1〉 junctions have been found and characterized. Many collinear interactions have been identified either involving direct interactions between crossing dislocations of opposite Burgers vectors or indirect interactions between dislocations gliding in parallel planes and sessile dislocation loops. We suggest that collinear interaction, already identified as the primary source of strain hardening in FCC metals, is the main dislocation interaction mechanism in olivine deformed at temperatures below 1000 °C.
ISSN: 1478-6443

hal-01174166
https://hal.archives-ouvertes.fr/hal-01174166
DOI : 10.1080/14786435.2014.1000996