Éditeur(s) : HAL CCSD
Résumé : Fault zones are major discontinuities in sedimentary basins. Understanding their role on fluid migrations is an essential issue to (i) characterize the mechanisms and kinematics of deformation and (ii) to determine the parameters which control the distribution of energetic or mineral resources. This work applies to faulting under a temperature range of 200-250°C, corresponding to that of deeply buried reservoirs as well as potentially seismogenic fault zones. The studied faults are normal faults affecting the “Grès d’Annot” Formation, a Priabonian-Rupelian siliclastic turbidite succession of the Alpine foreland basin. They are located in two distinct areas: the Moutière-Restefond area in the eastern part of the basin and the Estrop area in the western part. Vitrinite reflectance outside fault zones indicates maximal temperatures of 240-260°C at Moutière-Restefond and 170-200°C at Estrop, i.e. burial depths around 8 km and 6 km, respectively, assuming a mean geothermal gradient of 30°C/km. Burial was due to underthrusting below the Embrunais-Ubaye Alpine nappes, the difference in burial between the two areas traducing the westward taper of the nappe front.The studied faults affect alternating arkosic sandstone beds and pelite layers with offsets from centimeters to decameters. Two types of core zones are recognized: (1) the foliated core zones of the Moutière-Restefond area, where deformation dominated by pressure solution and synkinematic phyllosilicate neoformation resulted in a foliated fabric, and (2) the core zones of the Estrop area, characterized by dilatant quartz-mineralized veins and breccia. Fault and host rock petrophysical properties were measured on drill plugs, using the water porosity technique and nitrogen permeability technique under 2 Mpa of confining pressure. In the Moutière-Restefond fault zones, plug axes were oriented in three orthogonal directions corresponding to the main deformation axes (X, Y, Z) of the foliated arkose to characterize the effect of structural anisotropy. In the Estrop fault zones, where deformation does not show equivalent anisotropy, the plug axes were oriented according to the main fault plane orientation (i.e., parallel to azimuth, parallel to dip and normal). In each fault zone, the porosity of fault rocks is equivalent to that of host rocks. In the Moutière-Restefond fault zones, the plugs parallel to the X and Z axes of deformation have a permeability similar to that of the host rocks, whereas permeability parallel to the Y axis (i.e. parallel to the foliation and the main fault plane) is one order of magnitude higher. By contrast, the permeability values in the Estrop fault zones are isotropic and equivalent to the host rock values. This study highlights the importance of various types of deformation mechanisms and related fluid-rock interactions in determining different fault rock types within a similar protolith, ultimately controlling distinct petrophysical properties of fault zones.
Les zones de failles constituent des discontinuités majeures dans la croûte supérieure. Ce mémoire s’intéresse aux failles actives à des profondeurs de 5-8 km, i.e. dans des conditions pouvant jouer un rôle important (i) sur le comportement mécanique de de la croûte, en particulier sur son potentiel sismogénique et (ii) sur la compartimentation des réservoirs géologiques profondément enfouis.Les failles étudiées sont des failles normales (rejet jusqu’à 50 mètres) affectant des alternances de bancs de grès arkosiques et de pélites dans les Grès d’Annot, une formation turbiditique d’âge priabonien-rupélien du bassin d’avant-chaine alpin. Les Grès d’Annot ont été enfouis sous les nappes de l’Embrunais-Ubaye peu de temps après leur dépôt et exhumés au Miocène moyen-supérieur. L’étude a été réalisée dans deux secteurs des Alpes de Haute-Provence, (1) le secteur de l’Estrop (chaine des Trois Evéchés, dans la partie occidentale du bassin) et (2) le secteur de Point Vert-Restefond (alentours du col de la Bonette, dans la partie orientale du bassin). La réflectance de la vitrinite dans les Grès d’Annot indique des températures maximales de 160-190°C dans le secteur (1) et de 240-260 °C dans le secteur (2) , soit des profondeurs d’enfouissement de 5-6 km et 8-10 km, respectivement, dans l’hypothèse d’un gradient géothermique moyen de 25-30°C/km. A partir des observations microstructurales, de données d’inclusions de fluides, de modélisations thermodynamiques sur chlorites syncinématiques et des indices de cristallinité de l’illite, on a établi que les failles du secteur (1) ont fonctionné à une température d’environ 200°C pour une pression de 0.6Kbar et celles du secteur (2) dans une gamme de température de 200-220°C et de pression comprise entre 0.6 et 1.1 Kba. L’activité de la faille de Point-Vert a été datée par la méthode 40Ar/39Ar au Miocène inférieur (21 Ma). Ces failles sont interprétées comme associées aux premiers stades du soulèvement résultant de l’activité des chevauchements dans le socle sous-jacent.Deux types principaux de roches de failles caractérisent les failles étudiées. Les brèches dilatantes sont majoritaires dans les zones de failles du secteur (1) alors que les arkoses foliées sont majoritaires dans les zones de failles du secteur (2). Les brèches dilatantes témoignent de mécanismes de déformation dominés par la fracturation transgranulaire et la pression-solution des silicates. Ce dernier mécanisme se manifeste principalement par d’abondantes précipitations cycliques de quartz, les stylolites restant peu développés. Les géométries structurales sont associées à l’activation de plans T de Riedel déterminant l’ouverture de relais extensifs et un régime localement dilatant. Nous associons ce type de roche de faille à une faible pression effective au cours de la déformation.La déformation cisaillante exprimée dans les arkoses foliées témoigne de mécanismes de déformation dominés par (i) la fracturation intragranulaire et transgranulaire, (ii) la pressionsolution/ précipitation des silicates, principalement le quartz, (iii) la néoformation de micas blancs liée à l’altération des feldspaths et (iv) la précipitation de chlorite. Ce travail montre également que les transformations minéralogiques liées aux interactions fluide-roche dans la zone de faille (forte augmentation de la proportion des phyllosilicates au dépend des feldspaths) changent radicalementla composition minéralogique de la roche. Nous associons ce type de roche de faille à une forte pression effective au cours de la déformation.La pétrophysique montre que les brèches de failles (secteur 1) ont une perméabilité isotrope et équivalente à celle du protolithe (10-3mD sous 2 MPa de confinement) tandis que les roches foliées (secteur 2) montrent une augmentation de perméabilité (10-2mD) selon l’axe Y de la déformation, d’un ordre de grandeur supérieure aux perméabilités suivant les axes X et Z et dans la roche hôte (10-3mD). Ce drain préférentiel potentiel est associé à l’orientation des phyllosilicates dans la foliation.
https://hal.archives-ouvertes.fr/tel-01310382

tel-01310382
https://hal.archives-ouvertes.fr/tel-01310382
https://hal.archives-ouvertes.fr/tel-01310382/document
https://hal.archives-ouvertes.fr/tel-01310382/file/Th%C3%A8seCAVAILHES2012.pdf

Éditeur(s) : HAL CCSD
Résumé : The Restefond fault, located in the Late Eocene-Early Oligocene Alpine foreland basin, affects the well lithified and low porosity Grès d'Annot. The fault core zone is characterized by the occurrence of highly deformed sandstone lenses. Deformation inside the lenses corresponds to mm to sub-mm-spaced cleavage planes rich in phyllosilicates and up to cm-thick and dm-long quartz-calcite pure extensional veins. The cleavages are mostly composed of newly-formed synkinematic white mica and chlorite. By using thermodynamic thermometers based on the chemical composition of chlorite, a temperature of 200 ± 20 °C of fault activity was computed. This temperature shows that the Restefond fault was active at burial conditions comprised between 6.5 and 8 km, assuming a mean geothermal gradient between 25 and 30 °Ckm−1. The petrophysic properties of sandstones from the core zone and in the hanging and foot wall of the fault were determined on drilled plugs following three spacial directions. The permeability of the highly deformed sandstone from the core zone is about one order of magnitude higher than in the host rock. This increase in permeability occurs in the direction parallel to the S-C structures and is explained by the occurrence of well-connected micropores localized between platy phyllosilicates. This study shows that the fault petrophysic properties are mostly controlled by the precipitation of synkinematic phyllosilicates under deep burial conditions.
Swiss Journal of Geosciences

hal-00795551
https://hal.archives-ouvertes.fr/hal-00795551
DOI : 10.1007/s00015-012-0099-z

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Field observations of highly porous and permeable sandstone in the Orange area (S-E Basin, France) show that networks of shear-enhanced compaction bands can form in a contractional regime at burial depths of about 400 m ± 100 m. These bands show equal compaction and shear displacements, are organized in conjugate and densely distributed networks, and are restricted to the coarse-grained (mean grain diameter of 0.6 ± 0.1 mm) and less porous (porosity of 26 ± 2%) sand layers. The bands are crush microbreccia with limited grain comminution and high grain microfracture density. They show reductions of permeability (mD) ranging from 0 to little more than 1 order of magnitude. They show no control on the alteration products related to meteoric water flow, which suggests that these shear-enhanced compaction bands have no or only negligible influence on subsurface fluid flow. Their selective occurrence and small (20%) reduction in transmissibility in densely populated layers prevented them from compartmentalizing the sandstone reservoirs. A comparison with compaction-band populations in the Navajo and Aztec sandtsones (western U.S.) emphasizes the role of burial depth and the presence of chemical compaction processes for the sealing potential of deformation bands.
ISSN: 0191-8141

hal-00807309
https://hal.archives-ouvertes.fr/hal-00807309
DOI : 10.1016/j.jsg.2012.11.008

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The Dien Bien Phu (DBP) Fault strikes nearly perpendicular to the general tectonic framework, separating northwest Vietnam into two compartments. The DBP and Muong Lay granites are exposed respectively east and west of the fault. The U/Pb age of 277 ± 2 Ma obtained for the Muong Lay granite is similar to the age of the Chieng Khuong complex exposed within the Song Ma structure east of the DBP Fault. These two magmatic intrusions are considered as belonging to a same tectonic structure related to the subduction of the Song Ma Ocean under the Indochina Block during the Indosinian orogeny. The DBP Fault with a total post Permian dextral offset of 30-40 km shifts the Song Ma Suture. It could then be connected to the Ailao Shan-Shuanggou suture to the north. The undeformed DBP granite gave a U/Pb age of 230 ± 1 Ma sealing the Indosinian deformation on the fault. The Ladinian-Carnian activity of the fault is confirmed by the 40Ar/39Ar (biotite) age of 228 ± 4 Ma obtained from the paragneiss forming the fault zone. A geodynamic model is proposed to describe the various tectonic phases recorded by on the DBP Fault. It associates field data, stratigraphic observations, and geochronology analyses (U/Pb, Ar/Ar, fission tracks). Following the Late Triassic exhumation of the granite and the end of the Indosinian orogeny marked by the Norian unconformity, the granite was buried under Jurassic and Lower Cretaceous sediments. A strong cooling event during the early Late Cretaceous (100 Ma) is associated with the reactivation of the DBP Fault and the accommodation of a southward thrusting of the Song Da terrane onto the Truong Son Belt. This newly recognised tectonic phase could be associated to the subduction of the Paleo-Pacific plate under the Indochina Block. No data are available yet to constrain the Tertiary evolution of the DBP system. However, the Tertiary deformation is likely similar to the Cretaceous one.
ISSN: 1342-937X

insu-01015379
https://hal-insu.archives-ouvertes.fr/insu-01015379
DOI : 10.1016/j.gr.2013.07.018

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
On the Gulf of Lions margin, the Messinian Salinity Crisis (MSC) event led to a significant and widespread erosion of the Miocene shelf and slope. It is thus difficult nowadays to restore the morphology of the margin at the beginning of the crisis, and to study the Middle-Upper Miocene series rarely preserved from erosion. In this study, thanks to the use of multichannel seismic reflection data from the Gulf of Lions western slope, it has been possible to image the Miocene slope deposits. Interpretation of the data reveals several diachronic sediment bodies just beneath the Miocene/Pliocene boundary. These bodies are related to slope erosional-depositional complexes, underlain by erosional unconformities outlined by seismic reflector truncations. They are V- or U-shaped in cross section. Over their mapped extent, these bodies are typically 8-12 km wide and incise up to 600 ms TWTT into the Miocene slope deposits. in plan view, they are roughly elongated NW-SE, perpendicularly to the present day shelf break, and they progressively migrate towards the South-East. We interpret these seismic bodies as buried Miocene submarine canyons pre-dating the dramatic drawdown related to the MSC. In this study we try to constrain their age, and we discuss the events that may be at their origin. We also discuss the long-term impact of these slope canyons on the evolution of the margin.
ISSN: 0264-8172

hal-00411546
https://hal.archives-ouvertes.fr/hal-00411546
DOI : 10.1016/j.marpetgeo.2008.04.006

Éditeur(s) : HAL CCSD
Résumé : International audience
High Pressure - Low Temperature (HP-LT) rocks testify for burying and exhumation of crustal material in subduction zones. The question of their exhumation is nevertheless still unclear. The Aegean domain offers several HP-LT belts. Especially, the Attic-Cycladic Blueschist unit (ACBU) is an example of a HP-LT unit exhumed in a convergent and then in a divergent context. It actually appears in metamorphic core complexes (MCCs) formed in the back-arc of the subduction. The syn-convergence "message" is however difficult to read because of the post-convergence structural and thermal overprint that accompanied the formation of the MCCs. Particularly, the geometry, the timing and the amount of the syn-orogenic exhumation remain unclear. We investigate theses questions with metamorphic petrology (Andros and Ios islands) and phengite population, single grain and in situ 40Ar-39Ar geochronology (Andros, Tinos, Syros and Ios islands). Based on these new constraints and a synthesis of published data, we are able to refine the geometry, the timing and the modes of the exhumation of the ACBU. Data from the whole Cyclades exhibit little differences in the age and P-T conditions at the successive stages of syn-orogenic exhumation. The peak of pressure (500±50 °C-18±1 kbar) has been reached at 50-55 Ma. The onset of the exhumation occurred at 40-45 Ma in blueschist facies conditions, between a basal thrust and a summital detachment. The following decompression was accompanied by cooling until 30-35 Ma (400±50 °C-8±1 kbar). At that time, the boundary conditions switched to extension. The change in boundary conditions is recorded by slowing of the exhumation and isobare heating. The conditions of post-orogenic exhumation differ from an island to another. The onset of post-orogenic exhumation is dated around 30 Ma in the northern Cyclades and 25 Ma in the southern Cyclades. It is related to top-to-the-North deformation in all the studied domain. The end of ductile deformation below the detachments is also diachronous (21 Ma in the North and 18 Ma in the South). Finally, we propose a model for the final steps of the exhumation related to the intrusion of granitic bodies around 14 Ma.
American Geophysical Union, Fall Meeting
San Francisco, United States

insu-00860510
https://hal-insu.archives-ouvertes.fr/insu-00860510
BIBCODE : 2010AGUFM.T23C2301L

Éditeur(s) : Elsevier
Résumé : Sediment cores acquired in 2004 off the Rhone prodelta show consistent anomalous methane concentrations of up to 87,440 ppm. Methane compositional and isotopic data support a biogenic origin, although there are a few sites that show strongly depleted delta C-13 values (-53%o PDB) suggesting a mixed source for the gas (biogenic and thermogenic). Anomalous methane concentrations (samples with more than 90 ppm) are discussed and integrated with organic carbon data, sedimentary rates and ADCP profiles. Highest gas concentrations were found directly off the river mouth (20-40 m water depth) and where the IFREMER models point to the thickest accumulation (> 2 m) in response to the Rhone flood event. In areas unaffected by the high flux of organic matter and rapid/thick flood deposition, or in between flood events, the conditions for methanogenesis and gas accumulation have not been met; in these areas, the physical and biological reworking of the surficial sediment may effectively oxidize and mineralize organic matter and limit bacterial methanogenesis in the sub-surface. We propose that in the Rhone prodelta flood deposits deliver significant amounts of terrigenous organic matter that can be rapidly buried, effectively removing this organic matter from aerobic oxidation and biological uptake and leading to the potential for methanogenesis with burial.
Marine Geology (0025-3227) (Elsevier), 2006-12 , Vol. 234 , N. 1-4 , P. 215-231

Droits : 2006 Elsevier B.V. All rights reserved
http://archimer.ifremer.fr/doc/2006/publication-2396.pdf
DOI:10.1016/j.margeo.2006.09.005
http://archimer.ifremer.fr/doc/00000/2396/

Éditeur(s) : HAL CCSD
Résumé : International audience
The Jaca basin is a thrust-sheet top basin transported southward andunderlain by basement and cover thrusts separated by a Triassic décollement.Basin-fill upper Cretaceous to lower Oligocene synorogenic sequencesrecord a southward depocenter migration, while growth stratadate a shift of deformation from the mid-Eocene in the N to the earlyMiocene in the S (S-Pyrenean front). However, the deep geometry andkinematic relationships between the cover and basement thrusts remainnon-consensual. We present a new structural and kinematic interpretationfor the eastern Jaca basin, based on subsurface structural maps andcross-sections constructed using industrial seismic reflection profiles.Raman Spectroscopy of Carbonaceous Material (RSCM), vitrinite reflectanceand apatite fission track (AFT) thermochronology data givefurther constraints for the restoration of the deformation and burialexhumationsequence. We define 3 main basement thrusts under thenorthern part of the basin, from N to S the Broto, Fiscal and Guargathrusts. The study also clarifies the deep structure of the cover thrustsand their links with these basement thrusts and those located more tothe north in the Axial Zone (AZ), which altogether define the timing ofthe basement thrust sequence as follows : the Lakoura-Eaux Chaudesthrust system (northern AZ) active up to the end Bartonian, the Gavarnie(central AZ) and Broto thrusts during the Priabonian-Rupelian andthe Fiscal and Guarga thrusts during the late Oligocene-early Miocene.AFT results in the basin fill and AZ date the exhumation of the basinto the late Oligocene-early Miocene, in relation to the Fiscal-Guargathrusting. AFT partial reset argues for a maximum burial < 6 km forthe base of the Eocene detrital sequence (Hecho Group turbidites). Bycontrast, RSCM and vitrinite thermometry at the same level indicatesTmax around 180°C, locally up to 240°C, attesting to a temperature anomalypossibly related to transient fluid circulation.
24 ème Réunion des sciences de la Terre 2014
Pau, France

insu-01080836
https://hal-insu.archives-ouvertes.fr/insu-01080836

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : Vertical displacements on the SW-NE T (e) over capt fault (Eastern Pyrenees Axial Zone, France), which separates the Variscan Canigou-Caranca and Mont-Louis massifs, were constrained using a thermochronologic multi-method approach. Ar-40/Ar-39 data from the granitic Mont-Louis massif record its Variscan cooling history and reveal no ages younger than Early Cretaceous, while the Canigou-Caranca gneiss massif records systematically younger Ar-40/Ar-39 ages. These younger Ar-40/Ar-39 ages in the Canigou-Caranca gneiss massif are the result of partial to total rejuvenation of argon isotopic systems related to a thermal flow coeval with the Cretaceous HT-BP metamorphism in the North Pyrenean Zone. Only the deepest rocks from the Canigou-Caranca suffered this extensive Mid-Cretaceous thermal overprint probably due to differential burial around 4 km at that time. The post Mid-Cretaceous vertical displacements along the T (e) over capt fault are recorded by "low" temperature thermochronology using K-feldspar Ar-40/Ar-39, zircon and apatite fission track and (U-Th)/He datings. The Mont-Louis granite samples experienced a long period of protracted cooling reflecting a lack of thermo-tectonic activity in this area from Late Palaeozoic to Early Cenozoic, followed by cooling from 55-60 Ma to Late Eocene at a mean rate of 15-20 degrees C/Ma in the final stage. This cooling stage corresponds to T (e) over capt fault reactivation with a reversed component, promoting exhumation of the Mont-Louis roof zone contemporaneously with the south-vergent Pyrenean thrusting. In the Canigou-Caranca massif, the main cooling event occurred from 32 to 18 Ma at a maximum rate of 30 degrees C/Ma during Early Oligocene followed by a more moderate rate of 3 degrees C/Ma from Late Oligocene to Early Burdigalian, coeval with the normal reactivation of the T (e) over capt fault in brittle conditions that accommodated the final exhumation of the massif during the opening of the Gulf of Lion.
ISSN: 1437-3254

hal-00411442
https://hal.archives-ouvertes.fr/hal-00411442
DOI : 10.1007/s00531-007-0179-x

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
At the North-Ecuadorian convergent margin (1°S–1.5°N), the subduction of the rough Nazca oceanic plate leads to tectonic erosion of the upper plate and complex seismogenic behavior of the megathrust. We used three selected pre-stack depth migrated, multi-channel seismic reflection lines collected during the SISTEUR cruise to investigate the margin structure and decipher the impact of the subducted Atacames seamounts on tectonic erosion, interseismic coupling, and seismogenesis in the region of the 1942 Mw7.8 earthquake.This dataset highlights a subducted ∼30×40 km∼30×40 km, double-peak seamount that belongs to the Atacames seamount chain and that is associated with a deep morphologic re-entrant containing mass transport deposits.The seamount subduction uplifted the margin basement by ∼1.6 km and pervasively broke the margin by deep and intense reverse faulting ahead of the seamount, a process that is likely to weaken considerably the margin. In the seamount wake, the basement reverse fault system rotated counter-clockwise. This faulted basement is overlain with slope sediment sliding along listric normal faults that sole out onto the BSR. This superposition of deep tectonic contraction within the basement and shallow gravitational extension deformation within the sediment highlights the key role of gas hydrate on outer slope erosion.In addition to long-term regional basal erosion, the margin basement has thinned locally by an extra 0.8–1 km in response to the subduction of the Atacames seamount chain and hydrofracturing by overpressured fluids at the margin toe. This pervasively and deeply fractured margin segment is associated with a seismically quiet and GPS-modeled low interseismic coupling corridor that terminates downdip near the 1942 epicenter and locked zone. We suggest that the deeply buried double-peak Atacames seamount triggered the 1942 earthquake ahead of its leading flank. This result supports previous studies proposing that subducted seamounts provide unfavorable conditions for locking the updip segment of the plate boundary limiting the updip extent of seismogenic zones, but may favor large subduction earthquakes at greater depths.
ISSN: 0012-821X

hal-01256399
https://hal.archives-ouvertes.fr/hal-01256399
DOI : 10.1016/j.epsl.2015.10.043

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
3D seismic data located in the Gjallar Ridge (Vøring Basin, offshore Norway) reveals a closely-spaced polygonal fault system affecting more than 800 m of homogeneous mud-dominated Quaternary and Tertiary sequences. As some faults reach the modern seafloor, they represent an active polygonal fault system at present day. Even if the processes remain unclear and are still under debate, it is generally agreed that the initiation of polygonal faults is the result of shallow burial dewatering of fine-grained unconsolidated sediments by volumetric compaction. 3D seismic data are commonly interpreted by propagating horizons automatically and by picking faults manually. However, in the case of polygonal fault intervals, this approach is time consuming due to the huge number of faults and because automatic propagation can be misleading. In this study, we applied a new technique of 3D seismic interpretation based on a sequential stratigraphy analysis, using the new PaleoScan© software (Eliis Company). It allowed us to build a 3D geological model computing more than 300 horizons within the faulted intervals. We then used the coherency attribute, depicting anomalies in the shape of seismic waveform like faults, in order to constrain a possible link between fault distribution and stratigraphic levels. Our approach allows fault throws to be calculated in milliseconds on any polygonal fault plane. The result shows that fault segments have been reactivated by dip-linkage. Distribution of faults depends on mechanical units, intervals characterized by different petrophysical properties, which are independent from lithological and diagenetic changes. According to these results, we propose a model showing the evolution of polygonal fault intervals in which faulting stages are separated by a quiescence phase during burial. A first tier of polygonal faults is initiated at a specific depth, according to the Cam-clay model. Then, following a period of quiescence during which mud-rich sediments continued to accumulate, new fault segments are initiated above the first mechanical unit and within this undeformed interval. New nucleated faults then connect downward to pre-existing underlying polygonal fault system, thus progressively increasing the thickness of the faulted interval.
ISSN: 0025-3227

hal-00772470
https://hal.archives-ouvertes.fr/hal-00772470
DOI : 10.1016/j.margeo.2012.07.016

Éditeur(s) : HAL CCSD
Résumé : In this work on a complete transect of the west‐central Pyrenees, we combine low temperature thermochronology (apatite fission tracks, AFT) with a detailed structural analysis to describe vertical movements related to the thrusting system evolution, and to determine the influence of the latter on the sedimentation/burial/exhumation cycle of thesynorogenic deposits of the southern foreland basin (Jaca and Ainsa basins). AFT analysis from a transect of the south‐Pyrenean basin show the southward decrease of the fission track reset level from the southern edge of the Axial Zone to the South‐Pyreneanfrontal thrust, implying the southwards decrease of the burial amount from more than 5kmin the north to less than 3km in the south assuming an average geothermal gradient of 25°C.km‐1. The structural setting of the Jaca basin attests that the burial of the synorogenicsediments was mainly due to the sedimentary accumulation. AFT data from the northernpart of the basin display a late Oligocene‐early (middle) Miocene cooling event. Newinterpretation of industrial seismic reflection profiles across the Jaca basin suggests that the Oturia thrust is rooted in the Bielsa basement thrust, responsible for the early (‐middle) Miocene out‐of‐sequence tectonic reactivation of the southern flank of the Axial Zone (Jolivet et al., 2007). These results reveal a lower Miocene (Burdigalian ‐?Langhian) out‐of sequence episode of tectonic activity of the interior of the south‐Pyrenean foreland basin. AFT data from the Axial Zone and the North‐Pyrenean Zone confirm the general southwardmigration of the thrusting system, and also bring evidence of the late Oligocene‐lowe rMiocene out‐of‐sequence tectonic reactivation of the northern flank of the Axial Zone. All these results attest of a late Oligocene‐lower Miocene (Burdigalian‐?Langhian) "pop‐up" reactivation of the inner part of the west‐central Pyrenees, younger than the sealing of thesouth‐Pyrenean front (Aquitanian‐?Burdigalian) which is classically considered to mark the end of the Pyrenean compression. These results lead us to propose a new crustal scale evolution model of the west‐central Pyrenees in 3 stages: (i) From the Late Cretaceous to themiddle Eocene, the orogenic prism is characterised by the absence of relief, related to theinversion of Cretaceous extensional structures leading to the accretion of thin crustal units; (ii) The late Eocene‐Oligocene stage corresponds to the continental collision, marked by the creation of important relief associated with the accretion of thick crustal units; (iii) During the early Miocene, the inner part of the Pyrenean wedge is tectonically reactivated.
Ce travail de thèse concerne une transversale complète des Pyrénées centro-occidentales, où on a combiné la thermochronologie basse température (traces de fission sur apatites, TFA) avec une analyse structurale détaillée pour décrire les mouvements verticaux associés à l'évolution du système chevauchant, et pour déterminer l'influence de ce dernier sur le cycle sédimentation/enfouissement/exhumation des dépôts synorogéniques du bassin d'avant‐chaine sud (bassins de Jaca et Ainsa). L'analyse TFA complète les données déjà publiées dans la Zone Axiale et la Zone Nord‐Pyrénéenne, e tconstitue la première étude de ce genre dans un bassin d'avant‐chaîne pyrénéen. Les données TFA sur la transversale du bassin sud‐pyrénéen montrent une diminution vers le sud du degré d'effacement des traces de fission, traduisant la diminution vers le sud de la quantité d'enfouissement, supérieure à 5 km au nord et inférieure à 3 km au sud dans l'hypothèse un géotherme de 25°.km‐1. Le contexte géologique montre que l'enfouissement est principalement lié à l'accumulation des dépôts synorogéniques. Les données TFA de lapartie nord du bassin montrent un refroidissement d'âge Oligocène supérieur‐Miocèneinferieur (moyen). Par ailleurs, une nouvelle interprétation de profils de sismiques réflexiondans le bassin de Jaca montre que le chevauchement d'Oturia s'enracine dans lechevauchement de socle de Bielsa, responsable de l'exhumation tectonique hors‐séquencedu bord sud de la Zone Axiale au Miocène inférieur (‐moyen) (Jolivet et al., 2007). Cesrésultats attestent donc de l'exhumation tectonique hors‐séquence au Miocène inférieur (Burdigalien‐ ?Langhien) de la partie nord du bassin d'avant‐chaine sud‐pyrénéen. Des données TFA obtenues dans la Zone Axiale et la Zone Nord‐Pyrénéenne confirment lamigration générale vers le sud du système chevauchant, et mettent également en évidencela réactivation tectonique hors‐séquence du bord nord de la Zone Axiale à l'Oligocèneterminal‐Miocène inférieur. L'ensemble de ces résultats atteste donc de la réactivation en " pop‐up " de la parties interne des Pyrénées centre‐ouest à l'Oligocène supérieur‐Miocèneinférieur (Burdigalien‐ ?Langhien), postérieurement au scellement du front sud‐pyrénéen (Aquitanien‐ ?Burdigalien) classiquement considéré comme marquant la fin de lacompression pyrénéenne. Ces données nous ont permis de proposer un nouveau modèle d'évolution crustale des Pyrénées centro‐occidentales en 3 grandes étapes : (i) du Crétacé supérieur à l'Eocène moyen, le prisme est caractérisé par une absence de relief, en lien avec l'inversion de structures extensives crétacées conduisant à l'accrétion de petites écailles crustales ; (ii) la période Eocène supérieur‐Oligocène correspond à la collision continentale proprement dite, et est marquée par la création d'importants reliefs associés à l'accrétion d'épaisses unités crustales ; (iii) au Miocène inférieur, la partie interne du prisme pyrénéen est réactivée.
https://tel.archives-ouvertes.fr/tel-00772154

Droits : info:eu-repo/semantics/OpenAccess
tel-00772154
https://tel.archives-ouvertes.fr/tel-00772154
https://tel.archives-ouvertes.fr/tel-00772154/document
https://tel.archives-ouvertes.fr/tel-00772154/file/thesemeresse.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : A synthesis of backscatter imagery coupled with a large 3D seismic dataset in the Lower Congo Basin (LCB) reveals a patchy distribution of features interpreted to be associated with fluid seepage from 300 m to 2500 m water depth. With the exception of one region of anomalous backscatter positive-relief mounds, all inferred seep sites occur in negative-relief pockmarks. The extensive 3D seismic dataset in the LCB offers a unique opportunity to study the plumbing system that is feeding surface cold seep systems, and in general, to reconstruct the relationship between tectonics and fluid flow in continental margins. The fluid seeps in the LCB are associated with morphologically, stratigraphically or tectonically controlled focused fluid flow. The integration of the geophysical datasets, backscatter imagery coupled to 3D seismic, clearly indicates that fluid seeps are not randomly distributed, but their seabed organization reflects 1) the location of the underlying structure (reservoir or trap) where the fluids are coming from, 2) the geometry and morphology of the reservoir/trap, and 3) the discontinuities in the sedimentary column along which fluids have migrated. In the LCB seafloor pockmarks are always associated with underlying tectonic structures (fault zones, salt diapirs, polygonal faults) or buried sedimentary bodies (turbiditic channels, erosional surfaces), whereas they never occur above sub-horizontal parallel-stratified fine-grained sediments. Even if triggering processes can not be clearly defined here, we propose a model of seafloor fluid seep organization, which represents a new tool for identifying the geometry of flow pathways and the underlying buried bodies where the fluids are originating from. This qualitative 3D model provides insight into the geohydrologic processes of continental margins.
ISSN: 0025-3227

hal-00406640
https://hal.archives-ouvertes.fr/hal-00406640
DOI : 10.1016/j.margeo.2007.06.003

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
This paper presents a new balanced structural cross-section of the Jaca thrust-sheet-top basin of the southern Pyrenees combined with paleo-thermometry and apatite fission track (AFT) thermochronology data. The cross-section, based on field data and interpretation of industrial seismic reflection profiles, allows refinement of previous interpretations of the south-directed thrust system, involving the identification of new thrust faults, and of the kinematic relationships between basement and cover thrusts from the middle Eocene to the early Miocene. AFT analysis shows a southward decrease in the level of fission track resetting, from totally reset Paleozoic rocks and lower Eocene turbidites (indicative of heating to Tmax > ~120 °C), to partially reset middle Eocene turbidites and no/very weak resetting in the upper Eocene-lower Oligocene molasse (Tmax < ~60 °C). AFT results indicate a late Oligocene-early Miocene cooling event throughout the Axial Zone and Jaca Basin. Paleo-maximum temperatures determined by vitrinite reflectance measurements and Raman spectroscopy of carbonaceous material reach up to ~240 °C at the base of the turbidite succession. Inverse modelling of AFT and vitrinite reflectance data with the QTQt software for key samples show compatibility between vitrinite-derived Tmax and the AFT reset level for most of the samples. However, they also suggest that the highest temperatures determined in the lowermost turbidites correspond to a thermal anomaly rather than burial heating, possibly due to fluid circulation during thrust activity. From these results, we propose a new sequential restoration of the south Pyrenean thrust system propagation and related basin evolution.
ISSN: 0278-7407

insu-01312746
https://hal-insu.archives-ouvertes.fr/insu-01312746
https://hal-insu.archives-ouvertes.fr/insu-01312746/document
https://hal-insu.archives-ouvertes.fr/insu-01312746/file/Labaume_et_al-2016-Tectonics.pdf
DOI : 10.1002/2016TC004192

Éditeur(s) : HAL CCSD American Association for the Advancement of Science
Résumé : 6 pages
International audience
Large impacts provide a mechanism for resurfacing planets through mixing near-surface rocks with deeper material. Central peaks are formed from the dynamic uplift of rocks during crater formation. As crater size increases, central peaks transition to peak rings. Without samples, debate surrounds the mechanics of peak-ring formation and their depth of origin. Chicxulub is the only known impact structure on Earth with an unequivocal peak ring, but it is buried and only accessible through drilling. Expedition 364 sampled the Chicxulub peak ring, which we found was formed from uplifted, fractured, shocked, felsic basement rocks. The peak-ring rocks are cross-cut by dikes and shear zones and have an unusually low density and seismic velocity. Large impacts therefore generate vertical fluxes and increase porosity in planetary crust.
ISSN: 0036-8075

hal-01399386
https://hal.archives-ouvertes.fr/hal-01399386
PUBMED : 27856906
DOI : 10.1126/science.aah6561

Éditeur(s) : HAL CCSD Elsevier
Résumé : Detailed sedimentological investigations on numerous outcrops and drill-core sections in the 2.1-Ga-old Franceville basin, Gabon, provide evidence for a large-scale injectite network. The injectites were formed by the injection of sands through a thickness of about 150 m of the FB1 Member, and now cover a minimum area of 70 km2 corresponding to the Bangombé plateau, but are also recognized close to Franceville 35 km farther south-east. The injectite lithology corresponds to a mud- or carbonate-supported sandstone characterized by a loose and uncompacted fabric contrasting with the host-rock. Because the injectites are often parallel to subparallel to the stratification, they were misinterpreted as depositional beds by previous authors. At outcrop, the injectite bodies exhibit sill, dyke, wing and protrusive geometries emplaced during early burial within poorly compacted material, with partial wall erosion and dissociation. The source of the sand material is attributed to a channel-levee turbidite depositional system located in the lower part of the FB1 Member. These deposits were buried by a thick biochemical muddy cap deposited during a starvation phase, which increased the seal capacity of the system. This type of architecture has a high potential to develop compaction disequilibrium during burial. Moreover, in the case of the Francevillian injectites, the abundance of microbial organic matter favoured early methane degassing and lateral charging of the sand reservoir. The overpressure in the channels was periodically released during early burial, through the effect of rapid sedimentary and tectonic loading, and possible seismic activity. The fluidized sand was injected according to a symmetrical wing pattern. Thus, the injected masses caused a local decrease in the grade of the lateritic manganese ore deposit of the Bangombé plateau.
ISSN: 0301-9268

hal-01667217
https://hal.archives-ouvertes.fr/hal-01667217
DOI : 10.1016/j.precamres.2017.09.022

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The potential effects of the mineralogical composition of sediment on the degradation of oil buried on sandy beaches were investigated. Toward that purpose, a laboratory experiment was carried out with sandy sediment collected along NW Iberian Peninsula beaches, tar-balls from the Prestige oil spill (NW Spain) and seawater. The results indicate that the mineralogical composition is important for the physical appearance of the oil (tar-balls or oil coatings). This finding prompted a reassessment of the current sequence of degradation for buried oil based on compositional factors. Moreover, the halo development of the oil coatings might be enhanced by the carbonate concentration of the sand. These findings open new prospects for future monitoring and management programs for oiled sandy beaches.
ISSN: 0025-326X

hal-01122779
https://hal.archives-ouvertes.fr/hal-01122779
DOI : 10.1016/j.marpolbul.2014.06.040

Éditeur(s) : Copernicus Gesellschaft Mbh
Résumé : During the GWADASEIS cruise (Lesser Antilles volcanic arc, February-March 2009) a very high resolution (VHR) seismic-reflection survey was performed in order to constrain Late Quaternary to Present faulting. The profiles we obtained evidence frequent "ponding" of reworked sediments in the deepest areas, similar to the deposition of Mediterranean "homogenites". These bodies are acoustically transparent (few ms t.w.t. thick) and are often deposited on the hanging walls of dominantly normal faults, at the base of scarps. Their thickness appears sufficient to compensate (i.e. bury) co-seismic scarps between successive earthquakes, resulting in a flat and horizontal sea floor through time. In a selected area (offshore Montserrat and Nevis islands), piston coring (4 to 7m long) was dedicated to a sedimentological analysis of the most recent of these particular layers. It corresponds to non-stratified homogenous calcareous silty sand (reworked calcareous plankton and minor volcanoclastics). This layer can be up to 2 m thick, and overlies fine-grained hemipelagites. The upper centimeters of the latter represent the normal RedOx water/sediment interface. Pb-210 and Cs-137 activities lack in the massive sands, while a normal profile of unsupported Pb-210 decrease is observed in the hemipelagite below, together with a Cs-137 peak corresponding to the Atmospheric Nuclear Experiments (1962). The RedOx level was thus capped by a recent instantaneous major sedimentary event considered as post-1970 AD; candidate seismic events to explain this sedimentary deposits are either the 16 March 1985 earthquake or the 8 October 1974 one (M-w = 6.3 and M-w = 7.4, respectively). This leads to consider that the syntectonic sedimentation in this area is not continuous but results from accumulation of thick homogenites deposited after the earthquakes (as observed in the following weeks after Haiti January 2010 event, McHugh et al., 2011). The existence of such deposits suggests that, in the area of study, vertical throw likely results from cumulated effects of separated earthquakes rather than from aseismic creep. Examination of VHR profiles shows that all major co-seismic offsets are recorded in the fault growth sequence and that co-seismic offsets can be precisely estimated. By using a sedimentation rate deduced from Pb-210 decrease curve (0.5 mmyr(-1)) and taking into account minor reworking events detected in cores, we show that the Redonda system may have been responsible for five > M-6 events during the last 34 000 yr. The approach presented in this work differs from fault activity analyses using displaced sets of isochronous surfaces and postulating co-seismic offsets. Combining VHR seismic imagery and coring we can decipher co-seismic vs. slow continuous displacement, and thus actually estimate the amplitude and the time distribution of major co-seismic offsets.
Natural Hazards And Earth System Sciences (1561-8633) (Copernicus Gesellschaft Mbh), 2012 , Vol. 12 , N. 5 , P. 1755-1767

Droits : Author(s) 2012. CC Attribution 3.0 License.
http://archimer.ifremer.fr/doc/00089/20040/21990.pdf
DOI:10.5194/nhess-12-1755-2012
http://archimer.ifremer.fr/doc/00089/20040/

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
We analyse the fluid flow regime within sediments on the Eastern levee of the modern Mississippi Canyon using 3D seismic data and downhole logging data acquired at Sites U1322 and U1324 during the 2005 Integrated Ocean Drilling Program (IODP) Expedition 308 in the Gulf of Mexico. Sulphate and methane concentrations in pore water show that sulphate-methane transition zone, at 74 and 94 m below seafloor, are amongst the deepest ever found in a sedimentary basin. This is in part due to a basinward fluid flow in a buried turbiditic channel (Blue Unit, 1000 mbsf), which separates sedimentary compartments located below and above this unit, preventing normal upward methane flux to the seafloor. Overpressure in the lower compartment leads to episodic and focused fluid migration through deep conduits that bypass the upper compartment, forming mud volcanoes at the seabed. This may also favour seawater circulation and we interpret the deep sulphate-methane transition zones as a result of high downward sulphate fluxes coming from seawater that are about 5-10 times above those measured in other basins. The results show that geochemical reactions within shallow sediments are dominated by seawater downwelling in the Mars-Ursa basin, compared to other basins in which the upward fluid flux is controlling methane-related reactions. This has implications for the occurrence of gas hydrates in the subsurface and is evidence of the active connection between buried sediments and the water column.
ISSN: 1468-8115

hal-00590501
https://hal.archives-ouvertes.fr/hal-00590501
DOI : 10.1111/j.1468-8123.2010.00304.x

Éditeur(s) : HAL CCSD
Résumé : When the upper crust below the mountain ranges shows crustal extension with a direction collinear to the convergence direction, it is generally accepted that it is the result of gravitational collapse. However, recent studies challenge this paradigm by showing that erosion induces uplift and extension in the central part of the low convergent mountain ranges. In this study, we investigate the impact of denudation on the seismotectonic regime of mountain ranges.In order to identify a relationship between seismotectonic regime and erosion, the first part of this work presents a compilation of data in the mountain ranges. Based on these observations, a simple kinematic model is proposed to predict the seismotectonic regime of the study ranges.For low convergence rate and moderate mean elevation ranges, this model predicts an extension regime when the denudation rate is 15% higher than the convergence rate.The second part is devoted to the development of thermomechanical 2D finite element models to study the impact of surface processes on the deformation of the Pyrenees. The results show that the isostatic response to erosion reactivates pre-existing structures. The kinematics of an inherited fault plane can be predicted due to the gradient of the horizontal surface velocity profile. Thus, a plane located in the eroded zone is reactivated in normal fault when near the border of the erosion area, this same plane is reactivated in reverse fault. These results suggest that the current deformation in the North Pyrenean Zone could be the result of surface processes.Given the small number of studies quantifying erosion rates in the Pyrenees, the models developed in the second part suffer from high uncertainty. To remedy this, we study the central Pyrenees through a study that combines two types of data : watershed denudation rates from cosmogenic isotopes concentration, and incision rates from sediments buried in the karst. These results are presented in chapter 3. Denudation profiles obtained are consistent with reactivation of a normal fault plane located in the North Zone of the Central Pyrenees.From our study in the Pyrenees, a good correlation appears between the value of the rate of erosion and the glacier occupation. Given that the glaciers where more developed in the Alps, it raises the question of the impact of the late-würmian deglaciation on the present deformation of this range. A numerical model detailing this relationship is presented in the fourth chapter. Theresults show that deglaciation of the western Alps is controlled by the rheological heterogeneity of the crust. Some of our models predict uplift rates consistent with those highlighted by geodesy.
Lorsque l’extension de la croûte sous les parties hautes des chaînes de montagnes est colinéaire à la direction de convergence, il est traditionnellement admis que le moteur est l’effondrement gravitaire. Pourtant, des études récentes remettent en cause ce paradigme en montrant que l’érosion induit un soulèvement et de l’extension dans la partie centrale des chaînes de montagne à faible taux de convergence. L’objectif de notre étude est d’étudier l’impact de la dénudation de la topographie sur le régime sismo-tectonique des chaînes de montagnes.La première partie de ce travail présente une compilation de données dans les chaînes de montagnes afin de dégager des relations entre régime sismo-tectonique et érosion. Sur la base de ces observations, un modèle cinématique simple permettant de prévoir le régime de la chaîne est proposé. Ainsi, pour les chaînes à faible taux de convergence et d’élévation moyenne, ce modèleprédit de l’extension lorsque le taux de dénudation est 15% plus élevé que le taux de convergence.La deuxième partie est consacrée au développement d’un modèle thermo-mécanique 2D en éléments finis pour étudier l’impact des processus de surface sur la déformation des Pyrénées.Les résultats montrent que la réponse isostatique à l’érosion permet de réactiver des structurespré-existantes. La cinématique d’un plan de faille hérité peut être prédite grâce au gradient du profil des vitesses de surface horizontales. Ainsi, un plan situé dans la zone d’érosion est réactivé en faille normale alors qu’en bordure de cette zone une faille est réactivée en régime inverse. Ces résultats suggèrent que la déformation actuelle des Pyrénées pourrait être la conséquence d’unprocessus d’érosion.Compte tenu du faible nombre d’études quantifiant les taux d’érosion dans les Pyrénées, les modèles développés dans la deuxième partie souffrent d’une forte incertitude. Pour y remédier, nous avons cherché à les quantifier dans les Pyrénées Centrales grâce à une étude qui combine deux types de données : taux de dénudation des bassins versants à partir des isotopes cosmogéniques, et vitesses d’incision à partir des sédiments piégés dans les karsts. Ces résultats sontprésentés dans la troisième partie. Les profils de dénudation obtenus sont compatibles avec unrejeu en faille normale d’un plan situé dans la Zone Nord Pyrénéenne des Pyrénées Centrales.Notre étude dans les Pyrénées, montre une bonne corrélation entre la valeur du taux d’érosion et la cartographie de l’occupation glaciaire. Les glaciers ayant été plus développés dans les Alpes, cela pose la question de l’impact de la déglaciation tardi-Wurmienne sur la déformation actuelle de cette chaîne. Un modèle numérique détaillant cette relation est présenté dans le quatrième chapitre. Les résultats montrent que la déglaciation des Alpes occidentales est contrôléepar l’hétérogénéité rhéologique de la croute. Certains de nos modèles prédisent des vitesses de surrection compatibles avec celles mises en évidence par la géodésie.
https://hal.archives-ouvertes.fr/tel-01262333

tel-01262333
https://hal.archives-ouvertes.fr/tel-01262333
https://hal.archives-ouvertes.fr/tel-01262333/document
https://hal.archives-ouvertes.fr/tel-01262333/file/these-Genti-2015-postjury.pdf