Éditeur(s) : Springer
Résumé : The Var turbidite system is a small sandy system located in the Ligurian Basin. It was deposited during the Pliocene-Quaternary in a flat-floored basin formed during the Messinian salinity crisis. The system was fed through time by the Var and Paillon canyons that connect directly to the Var and Paillon rivers. It is still active during the present sea-level highstand. Two main mechanisms are responsible for gravity-flow triggering in the Var turbidite system: (1) mass-wasting events affect mainly the upper part of the continental slope, in areas where volumes of fresh sediment delivered by rivers are highest, and result from the under-consolidation state of slope sediments and earthquakes, and (2) high-magnitude river floods resulting from melting of snow and convective rainfall during fall and spring seasons, and generating hyperpycnal turbidity currents at river mouths when the density of freshwater transporting suspended particles exceeds that of ambient seawater. Failure- and flood-induced gravity flows are involved through time in the construction of the Var Sedimentary Ridge, the prominent right-hand levee of the Var system, and sediment waves. Processes of construction of both the Var Ridge and sediment waves are closely connected. Sandy deposits are thick and abundant in the eastern (downchannel) part of the ridge. Their distribution is highly constrained by the strong difference of depositional processes across the sediment waves, potentially resulting through time in the individualization of large and interconnected sand bodies.
Geo-Marine Letters (0276-0460) (Springer), 2006-12 , Vol. 26 , N. 6 , P. 361-371

Droits : 2006 Springer
http://archimer.ifremer.fr/doc/2006/publication-2258.pdf
DOI:10.1007/s00367-006-0047-x
http://archimer.ifremer.fr/doc/00000/2258/

Éditeur(s) : HAL CCSD Société Géologique de France
Résumé : Based on a High-Resolution 3D seismic block acquired in the Gulf of Lion in 2004–2005 we investigated fluid pipes and pockmarks on the top of the interfluve between the Hérault canyon and the Bourcart canyon both created by turbidity currents and gravity flows from the shelf to the deep basin in the north-western Mediterranean Sea. Combining the geometry of the potential fluid pipes with the induced deformation of surrounding sediments leads then to the ability to differentiate between potential fluid sources (root vs source) and to better estimate the triggering mechanisms (allochtonous vs. autochtonous cause). We linked together a set of derived attributes, such as Chaos and RMS amplitude, to a 3D description of pipes along which fluids may migrate. As previously shown in other basins, the induced deformation, creating cone in cone or V-shaped structures, may develop in response to the fluid pipe propagation in unconsolidated sediments in the near surface. The level at the top of a cone structure is diachronous. It means that stratigraphic levels over this surface are deformed at the end of the migration. They collapse forming a depression called a pockmark. These pipes are the result of repeated cycles of fluid expulsion that might be correlated with rapid sea-level rise instead of sediment loading. The most recent event (MIS 2.2 stage) has led to the formation of a pockmark on the modern seafloor. It has been used as a reference for calculating the effect of a rapid sea-level rise on fluid expulsion. As all physical and geometrical parameters are constrained, we were able to define that a + 34 m of sea level rise may account for triggering fluid expulsion from a very shallow silty-sandy layer at 9 m below seafloor since the last glacial stage. This value is consistent with a sea level rise of about 102 m during this period. This study shows that the episodic nature of fluid release resulted from hydromechanical processes during sea-level rise due to the interactivity between high pressure regimes and principal in situ stresses.
ISSN: 0037-9409

hal-01667241
https://hal.archives-ouvertes.fr/hal-01667241
DOI : 10.1051/bsgf/2017190

Éditeur(s) : HAL CCSD Springer
Résumé : International audience
We present here a synthesis of the evolution of rifted continental margin systems in the Gulf of Aden. These margins are volcanic to the west of the Gulf of Aden, where they are influenced by the Afar hotspot, and non-volcanic east of longitude 46° E. The combined use of magnetics, gravity, seismic reflection, field observations (tectonic, stratigraphic and sedimentological) and oil well data allowed us to obtain better constraints on the timing of continental rifting and seafloor spreading. From the Permo-Triassic to the Oligocene, the Arabian-African plate was subject to distributed extension, probably due, at least from the Cretaceous, to tensile stresses related to the subduction of the Tethysian slab in the north. In Late Eocene-Early Oligocene, 34-33 Ma ago, rifting started to localise along the future area of continental breakup. Initially guided by the inherited basins, continental rifting then occurred synchronously over the entire gulf before becoming localised on the northern and southern borders of the inherited grabens, in the direction of the Afar hotspot. In the areas with non-volcanic margins (in the east), the faults marking the end of rifting trend parallel to the inherited grabens. Only the transfer faults cross-cut the inherited grabens, and some of these faults later developed into transform faults. The most important of these transform faults follow a Precambrian trend. Volcanic margins were formed in the west of the Gulf, up to the Guban graben in the southeast and as far as the southern boundary of the Bahlaf graben in the northeast. Seaward dipping reflectors can be observed on many oil industry seismic profiles. The influence of the hotspot during rifting was concentrated on the western part of the gulf. Therefore, it seems that the western domain was uplifted and eroded at the onset of rifting, while the eastern domain was characterised by more continuous sedimentation. The phase of distributed deformation was followed by a phase of strain localisation during the final rifting stage, just before formation of the Ocean-Continent Transition (OCT), in the most distal graben (DIM graben). About 20 Ma ago, at the time of the continental break-up, the emplacement of the OCT started in the east with exhumation of the subcontinental mantle. Farther west, the system was heated up by the strong influence of the Afar hotspot, which led to breakup with much less extension. In the Gulf of Aden (s.str), up to the Shukra El Sheik fracture zone, oceanic spreading started 17.6 Ma ago. West of this fracture zone, oceanic accretion started 10 Ma ago, and 2 Ma ago in the Gulf of Tadjoura. Post-rift deformation of the eastern margins of the Gulf of Aden can be seen in the distal and proximal domains. Indeed, the substantial post-rift uplift of these margins could be associated with either the continental break-up, or activity of the Afar hotspot and related volcanic/magmatic activity. Uplift of the northern proximal margin was still active (e.g. stepped beach rocks exposed at 60 m of 2 Ma; 30 m of 35,200 years; 10 and 2 m) and active volcanoes can be inferred at depths of between 70 and 200 km beneath the margin (at 5-10 km distance from the coast). On the distal margin, heat flow measurements show a high value that is associated with post-rift volcanic activity and the development of a volcano (with flows and sills) shortly after the formation of the OCT. The Afar hotspot is therefore important for several reasons. It allows the localisation of deformation along the Red Sea/Aden system and the rapid opening of the Gulf after the continental break-up; its influence also seems to persist during the post-rift period.
ISSN: 1866-7411

hal-01053089
https://hal.archives-ouvertes.fr/hal-01053089
DOI : 10.1007/s12517-011-0475-4

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The nature and extent of the regional lithosphere-asthenosphere interaction beneath Ireland and Britain remains unclear. Although it has been established that ancient Caledonian signatures pervade the lithosphere, tertiary structure related to the Iceland plume has been inferred to dominate the asthenosphere. To address this apparent contradiction in the literature, we image the 3-D lithospheric and deeper upper-mantle structure beneath Ireland via non-linear, iterative joint teleseismic-gravity inversion using data from the ISLE (Irish Seismic Lithospheric Experiment), ISUME (Irish Seismic Upper Mantle Experiment) and GRACE (Gravity Recovery and Climate Experiment) experiments. The inversion combines teleseismic relative arrival time residuals with the GRACE long wavelength satellite derived gravity anomaly by assuming a depth-dependent quasilinear velocity-density relationship. We argue that anomalies imaged at lithospheric depths probably reflect compositional contrasts, either due to terrane accretion associated with Iapetus Ocean closure, frozen decompressional melt that was generated by plate stretching during the opening of the north Atlantic Ocean, frozen Iceland plume related magmatic intrusions, or a combination thereof. The continuation of the anomalous structure across the lithosphere-asthenosphere boundary is interpreted as possibly reflecting sub-lithospheric small-scale convection initiated by the lithospheric compositional contrasts. Our hypothesis thus reconciles the disparity which exists between lithospheric and asthenospheric structure beneath this region of the north Atlantic rifted margin.
ISSN: 0956-540X

hal-00617815
https://hal.archives-ouvertes.fr/hal-00617815
DOI : 10.1111/j.1365-246X.2011.04921.x

Éditeur(s) : Elsevier Science Bv
Résumé : In the South Gabon Basin, deep multi-channel seismic reflection and gravity modeling analysis have shed light on key features of the structure of the margin. The thinned continental crust beneath the Gabon Margin appears to be composed of two distinct layers, separated by a clear, strong and more or less continuous reflector running in the 7–10 s TWT window. The lower crust is characterized by a higher density, intermediate between the lower values of the upper crust and the denser values of the mantle. The lower crust is irregularly shaped and presents lateral thickness variations along the direction of thinning and along the coast. In the offshore thinned continental domain, the lower and upper crust form a 20–25 km thick body. Crustal thicknesses point to a relatively sharp and narrow transition, along a few tens of kilometers, between the unthinned and the thinned continental crust. The high density layer identified offshore Gabon presents similar characteristics in density, geometry and spatial distribution, as the underplated magmatic bodies observed along volcanic margins, e.g. along the South Atlantic Namibia Margin or the North Atlantic Vøring Margin. Although this lower crustal body could possibly represent ultra mafic serpentinized rocks or high grade metamorphic crustal rocks, we suggest that it could be composed of mafic rocks. Magmas resulting from partial melting during rifting may underplate the crust and/or be intruded in the lower crust through a system of dykes and sills. In this view, the present-day crustal thicknesses along rifted margins, characterized by magmatic underplating and/or intrusion, are not representative of the thinning that the crust experienced during rifting. Results of this study point to relatively shallow sedimentary basins along the South Gabon Margin. The deepest offshore depocenters located under the westernmost side of the continental platform appear to be associated with the deepest syn-rift basins These basins seem to extend along 20 to 40 km in the ~ NE–SW direction with a present-day average thickness of 7.3 km. Offshore Gabon, whereas the crustal thinning appears significant, the syn-rift deposit are not thick. We suggest that the area was anomalously uplifted during the rifting phase, due to an elevated thermal lithospheric gradient. The conclusions derived from our seismic and gravity analysis are consistent with the implications such a thermal anomaly would have on the tectonic evolution of a rifted margin with 1) an underplated high density lower crustal layer, 2) shallow depth syn-rift basins associated with a relatively thin crust and subsequently 3) elevated recorded subsidence rates in the initial post-rift stages. Research Highlights ► The Gabon Margin appears characterized by an underplated high density lower crustal layer. ► Shallow depth syn-rift basins are associated with a relatively thin crust. ► Seismic and gravity analysis points to an anomalous uplift of the Gabon Margin during the rifting phase. ► Crustal structure, syn-rift infill and post-rift subsidence are consistent an uplift of the Gabon Margin during the rifting phase. ► The uplift of the Gabon Margin is possibly due to an elevated thermal lithospheric gradient.
Tectonophysics (0040-1951) (Elsevier Science Bv), 2011-06 , Vol. 506 , N. 1-4 , P. 31-45

Droits : 2011 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/00039/15020/12347.pdf
DOI:10.1016/j.tecto.2011.04.009
http://archimer.ifremer.fr/doc/00039/15020/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The 12 May 2008 the Sichuan earthquake was one of the worst natural disasters in China. Here, we present a detailed picture of the epicentral area inferred geophysical data. Based on the analysis of teleseismic data acquired by a dense seismic network, we highlight an abrupt 20 km Moho offset between the Sichuan Basin and the Tibetan plateau and a horizontal discontinuity at similar to 15 km depth, which may connect with the ruptured zone of the 2008 event. We obtain low mean crustal velocity ratios, which suggest the absence of a thick and extensive zone of partial melt within the crust beneath the eastern part of the Songpan-Garze Terrane. All our data support the idea that the Longmen Shan range mark a zone of active strain localization due to the rigid Yangtze craton resisting eastward displacement of the Tibetan Plateau.
ISSN: 0040-1951

hal-00534471
https://hal.archives-ouvertes.fr/hal-00534471
DOI : 10.1016/j.tecto.2009.11.010

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
The basis of this study is a new bathymetric map of the northeast Atlantic compiled from previously published maps made from conventional echosounder data, plus all Sea Beam data acquired on board the R/V JEAN CHARCOT since 1977. As most of the Sea Beam data have been obtained on the continental margin from Porcupine Seabight to the south of the Iberian Peninsula, a precise picture of the continental slope is given. A statistical analysis of the canyons, based on 750 measurements, reveals that many of the canyons present sharp changes in their direction, indicating a structural control mainly linked to the late Hercynian trends, especially around the Iberian Peninsula. Nevertheless, the paths of canyons may merely reflect recent gravity processes, as in the Porcupine Seabight. Canyons locally follow the directions of listric and associated transecting faults (Permian to Triassic and upper Jurassic to lower Cretaceous), as on the Celtic
ISSN: 0278-7407

hal-01261558
https://hal.archives-ouvertes.fr/hal-01261558
https://hal.archives-ouvertes.fr/hal-01261558/document
https://hal.archives-ouvertes.fr/hal-01261558/file/Lallemand1986-Tectonics.pdf
DOI : 10.1029/TC005i007p01125

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
The lateral variation of the mechanical properties of continental lithosphere is an important factor controlling the localization of deformation and thus the deformation history and geometry of intraplate mountain belts. A series of three-layer lithospheric-scale analog models, with a strong domain (SD) embedded at various depths, are presented to investigate the development of topography and deformation patterns by having lateral heterogeneities within a weak continental lithosphere. The experiments, performed at a constant velocity and under normal gravity, indicate that the presence or absence of the SD controls whether deformation is localized or distributed at a lithospheric scale. Deformation and topography localize above the edges of the SD, while the SD region itself is characterized by minor amounts of surficial deformation and topography. The depth of the SD (within the ductile crust, ductile mantle lithosphere, or both) controls the pattern of deformation and thus the topography. The presence of a SD in the ductile crust or in the mantle results in limited surficial topographic effects but large variations in the Moho topography. Strong Moho deflection occurs when the SD is in the ductile crust, while the Moho remains almost flat when the SD is in the mantle. When the SD occupies the ductile lithosphere, the SD is tilted. These analog experiments provide insights into intraplate strain localization and could in particular explain the topography around the Tarim Basin, a lithospheric-scale heterogeneity north of the India-Asia collision zone.
ISSN: 0278-7407

hal-01172472
https://hal.archives-ouvertes.fr/hal-01172472
DOI : 10.1002/2014TC003756

Éditeur(s) : HAL CCSD European Geosciences Union (EGU) European Geosciences Union
Résumé : The Moroccan Mediterranean coast is located in one of the area's most vulnerable to extreme weather events or tsunami hazards. The objective of this research is to reconstruct the historical extreme submersion-event record using sea-induced deposits preserved in coastal lagoon. The Nador lagoon is the largest Moroccan lagoon (115 km2). It is located along the western Mediterranean, which has a high cyclogenetic character and is exposed to tsunamis from the Alboran Sea. The sandy barrier which separates the lagoon from the Mediterranean Sea is marked by much overwash, which indicate how intensely it has been exposed to the adverse sea events through history. Using the UWITEC© gravity coring platform, an undisturbed MC4.5 core (1.15 m long) was successfully sampled in the studied lagoon. To identify extreme sea events, a multi-proxy approach was applied combining sedimentological and geochemical data. Three paleoevents were identified; all of them are concentrated over the last 500 years, and the most recent event corresponds to the 1889 storm. For the others deposits, it is difficult to determine exactly their origin; however, the high frequency of storm events over the relevant period and the absence of historical tsunamis evidence is more in favor of the meteorological origin.
ISSN: 1561-8633

hal-01146451
https://hal.archives-ouvertes.fr/hal-01146451
DOI : 10.5194/nhess-15-203-2015

Éditeur(s) : HAL CCSD Société géologique de France
Résumé : International audience
– The 300 km long allochthonous sheet of oceanic mantle forming the New Caledonia ophiolite displays three specific characters: 1) the ophiolite pile lacks concordant sheeted dykes and pillow basalt layers; 2) the ophiolite, refered to as the Peridotite nappe, is thrusted over the basaltic formations of the Poya terrane which are classicaly thought to originate from a different oceanic environment; 3) The basal contact of the ultramafic sheet is remarkably flat all along New-Caledonia and the Peridotite nappe has not been thickened during obduction, rather it experienced significant extension. This suggests that the peridotites have not been emplaced by a tectonic force applied to the rear. New petrological and geochemical results obtained from mantle rocks finally show that the Poya terrane may originate from the same oceanic basin as the peridotites. In this article, we consider such possible cogenetic links and we propose a simple model for the obduction of the New Caledonia ophiolite in which the Poya basalts represent the original cover of the Peridotite nappe. We infer that continuous uplift of the subducted units buried beneath the oceanic lithosphere in the northern part of New Caledonia drove passive uplift of the ophiolite and led to erosion and to initiation of sliding of the basaltic layer. During the Priabonian (latest Eocene), products of the erosion of the basaltic layer were deposited together with sediments derived from the Norfolk passive oceanic margin. These sediments are involved as tectonic slices into an accretionary wedge formed in response to plate convergence. The volcaniclastic sedimentation ends up with the emplacement of large slided blocks of basalts and rafted mafic units that progressively filled up the basin. Obduction process ended with the gravity sliding of the oceanic mantle sheet, previously scalped from its mafic cover. This process is contemporaneous with the exhumation of the HP-LT units of Pouebo and Diahot. Gravity sliding was facilitated by the occurrence of a continuous serpentine sole resulting from metasomatic hydratation of mantle rocks, which developed during the uplift of the Norfolk basement and overlying Diahot and Pouébo units. Progressive emersion of the obducted lithosphere allowed subsequent weathering under subaerial, tropical conditions. Obduction passive et mise en place gravitaire des grandes nappes ophiolitiques : les ophiolites de Nouvelle-Calédonie (SW Pacifique) sont-elles un cas d'école ? Résumé. – La nappe de manteau de Nouvelle-Calédonie, s'étendant sur 300 km de long montre trois caractéristiques im-portantes: 1) La succession ophiolitique ne contient ni dykes, ni basaltes en coussin, 2) l'ophiolite est charriée sur des formations basaltiques (nappe de Poya) que l'on considère classiquement comme originaires d'un bassin océanique dif-férent de celui d'où est issu le manteau, et 3) le contact basal de la nappe ultrabasique est remarquablement plat tout le long de l'île et celle-ci n'a pas été épaissie durant l'obduction. Cela suggère que les péridotites n'ont pas été mises en place en réponse à une poussée tectonique arrière. De nouveaux résultats pétrologiques et géochimiques obtenus sur l'ophiolite montrent en réalité que les basaltes de Poya peuvent être extraits de la fusion du manteau de l'ophiolite. Nous proposons donc un nouveau modèle pour l'obduction, dans lequel les basaltes de Poya forment la couver-ture initiale primitive du manteau de la nappe des péridotites. La surrection progressive des unités profondes enfouies lors de la subduction de la lithosphère du bassin sud-Loyauté à l'Eocène, a permis le soulèvement passif de l'ophiolite et l'érosion puis le glissement des unités basaltiques. Durant le Priabonien, l'accumulation des produits de l'érosion de la couche des basaltes et de la marge passive de Norfolk ont formé les séquences de flysch comprenant localement des débris basaltiques grossiers. Ces sédiments font partie d'un prisme d'accrétion tectonique construit en réponse à la convergence au front de la subduction. La sédimentation détritique se termine par la mise en place de grandes unités ba-saltiques glissées qui comblent le bassin. Le processus de l'obduction se termine par le glissement gravitaire de l'écaille de manteau océanique sur les basaltes. Cet événement est contemporain de l'exhumation des unités HP-BT de Pouébo et du Diahot. Le glissement gravitaire a été facilité par la présence sous l'ophiolite, d'une semelle continue de serpentines résultant de l'interaction du manteau avec des fluides métasomatiques remontant durant l'exhumation des unités en-fouies pendant la subduction continentale. L'émersion progressive de la lithosphère obduite a placé le manteau dans des conditions d'altération supergène tropicale.
EISSN: 1777-5817

hal-01257702
https://hal.archives-ouvertes.fr/hal-01257702
https://hal.archives-ouvertes.fr/hal-01257702/document
https://hal.archives-ouvertes.fr/hal-01257702/file/Lagabrielleetal-BSGF-2012-revised-light.pdf
DOI : 10.2113/gssgfbull.184.6.545

Éditeur(s) : HAL CCSD IOP Publishing
Résumé : The Bureau International des Poids et Mesures (BIPM), Sevres, France, hosted the 7th International Comparison of Absolute Gravimeters (ICAG) and the associated Relative Gravity Campaign (RGC) from August to September 2005.;ICAG 2005 was prepared and performed as a metrological pilot study, which aimed:;(1) To determine the gravity comparison reference values;;(2) To determine the offsets of the absolute gravimeters; and;(3) As a pilot study to accumulate experience for the CIPM Key Comparisons.;This document presents a complete and extensive review of the technical protocol and data processing procedures. The 1st ICAG-RGC comparison was held at the BIPM in 1980-1981 and since then meetings have been organized every 4 years.;In this paper, we present an overview of how the meeting was organized, the conditions of BIPM gravimetric sites, technical specifications, data processing strategy and an analysis of the final results. This 7th ICAG final report supersedes all previously published reports.;Readings were obtained from participating instruments, 19 absolute gravimeters and 15 relative gravimeters. Precise levelling measurements were carried out and all measurements were performed on the BIPM micro-gravity network which was specifically designed for the comparison.
ISSN: 0026-1394

hal-00644529
https://hal.archives-ouvertes.fr/hal-00644529
DOI : 10.1088/0026-1394/48/5/003

Éditeur(s) : HAL CCSD European Geosciences Union
Résumé : During the Neoproterozoic orogeny, the middle crust of the Araçuaí belt underwent widespread partial melting. At the regional scale, this anatectic domain is characterized by a progressive rotation of the flow direction from south to north, suggesting a 3-D deformation of the anatectic middle crust. To better determine whether melt volumes present in the anatectic middle crust of the Araçuaí orogen were large enough to allow a combination of gravity-driven and convergence-driven deformation, we used the titanium-in-quartz (TitaniQ) geothermometer to estimate the crystallization temperatures of quartz grains in the anatectic rocks. When possible, we compared these estimates with thermobarometric estimates from traditional exchange geothermobarometers applied to neighboring migmatitic kinzigites. TitaniQ temperatures range from 750 to 900 °C, suggesting that quartz starts crystallizing at minimum temperatures of ≥ 800 °C. These results, combined with the bulk-rock chemical composition of diatexites, allows the estimation of a minimum of ~ 30% melt and a corresponding viscosity of ~ 109–1010 Pa s. Such a minimum melt content and low viscosity are in agreement with interconnected melt networks observed in the field. Considering that these characteristics are homogeneous over a wide area, this supports the finding that the strength of the middle crust was severely weakened by extensive partial melting, making it prone to gravity-driven flow and lateral extrusion.
ISSN: 1869-9510

hal-01116434
https://hal.archives-ouvertes.fr/hal-01116434
DOI : 10.5194/se-5-1223-2014

Éditeur(s) : ISTPM
Résumé : The Caribean Sea ichthyofauna, like that of all tropical and subtropical seas, contains venomous fishes some of which can cause certain forms of ichthyosarcotoxism.The first people to notice, at their expense, the existence of these dangerous animals in the waters of the West Indies were the conquistadores who settled in Haïti and Cuba after Christopher COLOMBUS. As these men were not well provided by fresh supplies from their far away home-as related by many chroniclers-they had to live on local food resources. Originally, terrestrial fauna, in these islands, was very lacking as far as big mammals go, and birds bigger than a pigeon were rare. As a consequence, Spanish sailors and soldiers ate mostly seafood, fish, crustaceans and molluscs that abounded in the clear waters of the Caribean shores. (The introduction of European mammals: bovines, ovines, caprines and porcines, but also poultry, only happened many years later-cattle raising only developed when the conquistadores were well settled and land had been divided-initial protid production was not sufficient to cover the Spaniards' needs....
La faune ichthyologique de la Mer des Antilles, comme celle de toutes les mers des regions tropicales et subtropicales, contient des poissons vénéneux, causes de certaines formes d'ichthyosarcotoxisme. Les premiers qui s'aperçurent, à leurs dépens, de l'existence de ces animaux dangereux dans les eaux des Indes occidentales furent les conquistadores qui s'installèrent en Haïti et à Cuba après les découvertes de Christophe COLOMB et de ses lieutenants. Ces hommes, souvent fort mal ravitaillés par leur trop lointaine métropole -tous les chroniqueurs de l'époque en font foi -furent obligés d'utiliser les ressources alimentaires locales. Comme à l'origine, la faune terrestre des îles était très pauvre en grands mammifères et que les oiseaux plus volumineux qu'un ramier étaient rares, les soldats et les marins espagnols consommèrent surtout les fruits de la mer : poissons, crustacés et mollusques qui abondaient dans les eaux claires des rivages antillais. (L'introduction des mammifères européens: bovins, ovins, caprins et porcins, comme des oiseaux de basse-cour, fut relativement tardive; l'élevage ne se développa que lorsque les conquérants de l'Eldorado furent installés et que la terre fut partagée; la production initiale de protides était très nettement insuffisante pour couvrir les besoins des Espagnols.) L'un des animaux les plus faciles à capturer était -et l'est encore -le-« burgo », Linona pica L., gros gastéropode de la famille des Trochidés qu'il suffisait de récolter à la main sur les récifs coralliens ou les rochers qui bordaient les plages; l'abondance de la distribution de ce gros bigorneau est encore telle à l'heure actuelle qu'il forme une ressource permanente appréciée; dans certaines petites îles très mal ravitaillées: Los Hermanos et La Blanquilla dans les Antilles vénézuéliennes; Saint-Barthélémy, La Désirade, dans les Antilles françaises, etc., où le « burgo » constitue une partie importante de la ration alimentaire. Il arrivait à Cuba, que sa consommation soit la cause d'accidents gastro-intestinaux et neuraux qui furent groupés par les Espagnols sous le nom de "ciguatera", le mollusque lui-même étant appelé "cigua", (II faut noter que les « burgos » récoltés sur certains îlots et récifs de la côte méridionale de Saint-Barthélemy sont la cause de troubles analogues à ceux qui furent décrits par les chroniqueurs des XVe et XVIe siècles) Le vocable s'est étendu ensuite, dans le langage populaire, aux troubles digestifs et aux troubles neuraux ressentis après l'ingestion de différentes espèces de poissons vénéneux, espèces qui se révélèrent malheureusement relativement nombreuses dans les eaux des Grandes Antilles, Le auteurs anciens, repris par COUTIÈRE dans sa thèse (1899) décrivent également des cas d'intoxications graves depuis le début de l'occupation des Petites Antilles par les Européens, intoxications attribuées pour la plupart aux barracudas, aux balistes, aux murènes, à certains clupes, aux carangues comme à un certain nombre d'espèces de « poissons rouges ». Les naturalistes modernes, d'ARCISZ (1950) à RANDALL (1958), donnent la liste scientifique des espèces incriminables dans la Mer des Antilles. Il n'existe actuellement aucun manuel en langue française permettant la détermination des poissons marins et des espèces dulçaquicoles des Petites Antilles, Le naturaliste est obligé, pour identifier les poissons, de recourir à des ouvrages américains ou hollandais, ou encore à des monographies toutes rédigées en langue anglaise. Ces livres, à de très rares exceptions près, sont anciens et difficiles à trouver en librairie étant presque tous épuisés ou rares. La publication que nous présentons ici n'a pas la prétention de pallier l'inexistence de documents en langue française sur l'ensemble de la faune ichthyologique antillaise; elle n'a pour but que de fournir au personnel chargé du contrôle du conditionnement et des marchés, aux armateurs à la pêche désireux de se renseigner sur les possibilités locales, comme à quelques esprits curieux, une documentation suffisante et illustrée, pour permettre une identification sûre et rapide des espèces dangereuses. Cette étude est née d'un besoin précis : les pêcheurs des Antilles françaises, maintenant guidés par une assistance technique qui reprend élémentairement les bases de la profession, se sont heurtés très rapidement au fait suivant : il était nécessaire de créer un conditionnement des produits de la pêche car quelques espèces de poissons commerciaux, saines dans certaines régions, sont vénéneuses dans d'autres, géographiquement toutes voisines, et doivent être éliminées du marché. Pour cela il fallait établir avec précision quelles espèces pouvaient être dangereuses, et donner aux pêcheurs, aux marchands et au public l'image exacte des formes incriminables. Si une espèce donnée peut contenir des individus vénéneux, tous les individus de cette espèce ne sont pas dangereux et des spécimens de la même espèce incriminables en un point ne le seront pas dans d'autres lieux de pêche. POEY (1866) a écrit: « ... il n'y a pas un poisson suspect sur dix mille... » Cela est sans doute vrai si l'on envisage le stock constitué par une espèce, mais ne l'est plus si l'on considère les concentrations géographiques. A travers l'expérience que nous avons acquise à Saint-Barthélemy, nous pouvons affirmer avec certitude que les poissons vénéneux sont bien groupés en isolats cernés par des frontières géographiques précises. De plus il apparaît très nettement que les poissons âgés, donc ayant atteint un certain poids, sont seuls responsables des accidents ciguatériques les plus graves. Le fait que l'ichthyologiste cubain POEY, 1866, ait imposé l'interdiction des poissons pesant plus de trois livres dans les espèces suspectes sur le marché de La Havane est très significatif. Un fait statistique observé à Saint-Barthélemy vient corroborer les notions précédemment énoncées. Un certain nombre de canots de pêche à la ligne à main, travaillant à l'accore méridional du banc de Saint-Martin, capturait surtout des « oreilles noires » (Lufianus buccanella (c. et V.), 1828) et des « vivaneaux » (L. vivanus (c. et V.), 1828) ; le poids des poissons vidés acceptés par le service de contrôle de la coopérative des pêcheurs de Gustavia avait été fixé à 1 500 g; des poissons de poids bien supérieurs à ce plafond ayant été acceptés par le conditionnement en janvier et février 1963, toute une série d'intoxications graves de type ciguatérique se produisit à Basse-Terre et à Pointe-à-Pitre de La Guadeloupe, lieux principaux de consommation du poisson capturé sur le banc de Saint-Martin. Le poids des poissons vidés exportables ayant été ramené à 1 500 g. les intoxications cessèrent. Il reste à étudier l'étiologie de la «ciguatera », forme la plus commune d'ichthyosarcotoxisme notée aux Antilles. L'accumulation des observations et des notes prises à propos des cas observés à Saint-Barthélemy, à La Guadeloupe, comme à La Martinique (1950) ainsi que les dissections effectuées sur les poissons capturés par les pêcheurs de Saint-Barthélemy nous permettront peut-être de conclure bientôt à ce sujet. Enfin. il faudra trouver le test biochimique simple et précis permettant de déterminer rapidement si un poisson considéré comme « redouteux» est vénéneux ou non. (Les poissons incriminables sont désignés sous le nom de poissons «redouteux» dans le patois de Saint-Barthélemy; la « ciguatera » est nommée « mal poisson ».) Les appellations vernaculaires créoles des espèces vénéneuses ont été établies à partir des notes prises depuis 1950. Cette liste est loin d'être exhaustive car il n'y a pas de domaine plus ingrat que la synonymie vernaculaire. Les appellations américaines, britanniques et hollandaises ont été prises dans les ouvrages publiés d'une part par le Fish and Wildlife Service (laboratoire de Biologie marine de Miami), et d'autre part par la Commission des Caraïbes. Kent House, à La Trinidad. 1959. relayée ensuite par le Secrétariat central de l'Organisation des Caraïbes, 1961. Hato Rey. Porto-Rico. Enfin. nous avons pu établir l'équivalence vernaculaire des noms de poissons utilisés à Saint-Barthélemy et à Saint-Martin grâce à l'aimable collaboration du Dr PETIT, chef de l'hôpital de Marigot à Saint-Martin. Les bases de la systématique que nous avons utilisées, pour replacer les espèces décrites dans un cadre cohérent. sont celles qui sont exposées par BERTIN et ARAMBOURG (1958) dans le troisième fascicule du tome treize du Traité de Zoologie publié sous la direction du Pr P. GRASSÉ: nous y avons fait de larges emprunts. (OCR non contrôlé)
Revue des Travaux de l'Institut des Pêches Maritimes (0035-2276) (ISTPM), 1965-03 , Vol. 29 , N. 1 , P. 1-130

Droits : Ifremer
http://archimer.ifremer.fr/doc/1965/publication-4004.pdf
http://archimer.ifremer.fr/doc/00000/4004/

Éditeur(s) : Geological Society of America
Résumé : A seismic-refraction study of the sedimentary structure of the South West African continental shelf was carried out between lat 17°S and 24°S using expendable sonobuoys. Striking differences exist both in the topography and sedimentary structure between the shelf north and south of the Walvis Ridge. South of the ridge, as far as lat 23°S, the shelf consists of a prograded series, whereas north of the ridge, at least as far as lat 17°S, east-trending canyons cut the shelf sedimentary cover. The steep northem scarp of Walvis Ridge can be traced eastward under the sediment of the continental margin. The southern flank of the ridge is buried under a thicker sedimentary cover and could only be traced eastward to long. 10°E on seismic-reflection records. This flank probably parallels the northern scarp under the continental margin. Two-dimensional structural models, built with the help of seismic-retlection and seismic-refraction results and based on the hypothesis of local isostatic equilibrium, account for the obsewed gravity profiles. A compensating root consists of light material (density 2.95 g/cm3) and reaches a depth of about 25 km. Gravity results also suggest that the Walvis Ridge does not constitute a superimposed load on the lithosphere; rather, the ridge and its underlying compensating mass were created at approximately the same time as the adjacent ocean basins. The creation of the two aseismic ridges of the South Atlantic - the Rio Grande Rise and Walvis Ridge - by a mantle hot spot and plume is accepted; this theory seems to explain most of the peculiar features of the Walvis Ridge. However, it is probable that the surface expression of the mantle hot spot was controlled by the presence of weak zones in the lithosphere such as transform faults. [NOT CONTROLLED OCR]
Geological Society of America Bulletin (Geological Society of America), 1975 , Vol. 86 , P. 1713-1724

Droits : Geological Society of America
http://archimer.ifremer.fr/doc/1975/publication-4978.pdf
http://archimer.ifremer.fr/doc/00000/4978/

Résumé : Une étude de faisabilité de poutres en bois lamellé-collé a été menée en Guyane Française en utilisant les essences locales. Le but est de déterminer les paramètres de collage assurant la bonne résistance mécanique des assemblages par lamellation et par aboutage, nécessaires à la fabrication de poutres en bois lamellé-collé en climat tropical. Trois essences de bois abondantes de différentes densités ont été sélectionnées. Les adhésifs de types Mélamine-Urée-Formol et Résorcinol-Phénol-Formol ont été utilisées. Les paramètres de collage considérés sont : le grammage, le temps d’assemblage fermé et la pression.En utilisant les normes Européennes, plusieurs campagnes de tests ont été conduites sur des échantillons normalisés. Concernant le collage par lamellation, des tests élémentaires de délamination et de cisaillement des joints de colle ont été réalisés. Le test de délamination consiste en deux cycles d’immersion dans l’eau sous pression et de séchage, il induit de sévères variations d’humidité du bois susceptibles de créer des ouvertures des joints de colles. Le collage par aboutage est réalisé sur des poutres normalisées aboutées. Les entures sont obtenues grâce à un outillage standard communément utilisé pour les résineux. Les résultats ont mis en évidence l’influence des propriétés du bois et des paramètres de collage sur la résistance du joint et la résistance mécanique du produit. En effet, les paramètres du bois, tels que la densité, la rétractibilité et l’imprégnation, ont une forte influence sur le collage, en particulier sur la pression et le grammage nécessaires à la production d’un produit commercialisable. Il apparait qu’un bois de densité moyenne et poreux nécessite un grammage et une pression élevés comparé à un bois de densité élevée qui nécessite des valeurs moindres. Aussi, l’influence d’autres paramètres de fabrication, tels que le rabotage, l’encollage double face et simple face ainsi que l’épaisseur des lamelles, a été établie. Par contre il semblerait que le matériel communément utilisé pour l’aboutage des résineux n’est pas adapté aux feuillus tropicaux. En final, des paramètres de collage ont été validés pour la fabrication de lamellé-collé endémique en Guyane Française et une étude du coût de production d’une poutre lamellé-collé standard a identifié les conditions économiques d’une fabrication en Guyane Française.
A feasibility study of glued-laminated timber beams was carried out in French Guiana using local wood species. The aim of the study was to evaluate the gluing parameters that could ensure good mechanical properties for the manufactured glued-laminated beams in tropical climates. Three abundant wood species with different specific gravity were selected for the study. Melamine-Urea-Formaldehyde and Resorcinol-Phenol-Formaldehyde resins were used for gluing. The three gluing parameters considered are: adhesive spread rate, closing assembly time and gluing pressure.Using European standards, several laboratory tests were performed on normalized samples. The evaluation of a successful lamella’s gluing was done by using elementary tests of delamination and shearing. A delamination test consists of two cycles of water immersion at high pressure and drying which induces severe hygroscopic variation in wood thus causing joints opening. The finger-joints are made using a standard tool usually used for cutting softwoods. The performed tests revealed the influence of wood properties and the gluing parameters on the joint resistance and the mechanical properties of the product. Results show that wood properties such as specific gravity, shrinkage coefficient, and permeation, have a high degree of influence on the gluing step especially on the gluing pressure and on the adhesive spread rate needed to produce a commercial product. Furthermore, wood with medium specific gravity needs more adhesive and more pressure than the one with high specific gravity. Additionally, the effects of other manufacturing parameters, such as planning, double or simple side glue spreading and lamellae thicknesses, on the glue joint resistance were demonstrated. Finally, the common tools used for softwoods are not adapted to making the finger joints with tropical hardwoods.In conclusion, optimal gluing parameters for manufacturing glued-laminated timber beams in French Guiana were established and an economical study using standard glued-laminated timber beams revealed the economic conditions under which a successful manufacturing of these local beams can be implemented in French Guiana.

http://www.theses.fr/2011AGUY0484/document

Éditeur(s) : Elsevier Science Bv
Résumé : The Danube River Basin–Black Sea area represents a unique natural laboratory for studying the interplay between lithosphere and surface as well as source to sink relationships and their impact on global change. This paper addresses some information on the “active sink” of the system; i.e. the Danube deep sea fan and the Black Sea basin. The present study focuses on the distal sedimentary processes and the evolution of sedimentation since the Last Glacial Maximum. This is investigated through recently acquired long piston coring and shallow seismic data recovered at the boundary of influence of the distal part of the Danube turbidite system (to the north-west) and the Turkish margin (to the south). This dataset provides a good record of the recent changes in the sedimentary supply and climato-eustasy in the Black Sea region during the last 25 ka. This study demonstrates that the deep basin deposits bear the record of the Late Quaternary paleoenvironmental changes and that the western Black Sea constitutes an asymmetric subsident basin bordered by a northern passive margin with confined, mid-size, mud-rich turbidite systems mainly controlled by sea-level, and a southern turbidite ramp margin, tectonically active. Highlights ► Oceanographic results from survey carried out in the western Black Sea are presented. ► The Danube fan distal part: the Black Sea main depositional feature is described. ► This study is on the morphology and gravity sedimentation in the Black Sea deep basin. ► Data were collected at the boundary between the Danube fan and the Turkish margin. ► The dataset provide a good record of sedimentary supply and climato-eustatic changes.
Global And Planetary Change (0921-8181) (Elsevier Science Bv), 2013-04 , Vol. 103 , P. 232-247

Droits : 2012 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/00095/20637/18272.pdf
DOI:10.1016/j.gloplacha.2012.05.002
http://archimer.ifremer.fr/doc/00095/20637/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Joint inversions are now commonly used in the earth sciences. They have been developed to better understand the structure of the earth, since they provide more constraints on the inverted parameters. We propose a new process to simultaneously invert several data sets in order to better image 3D crustal and upper mantle structures. Our inversion uses three kinds of data that present good complementarity: (1) P-wave receiver functions to provide Moho depth variations, (2) teleseismic delay times of P-waves to retrieve velocity anomalies in the crust and the upper mantle, and (3) gravity anomalies to image density variations at the lithospheric scale. We use a stochastic scheme, where receiver functions are first inverted. The interpolated resulting Moho depths are incorporated as a priori information into the joint inversion of teleseismic delay times and gravity anomalies process. Moreover, velocity and density can be linked by empirical relationships, which justifies the joint inversion of those parameters. In our stochastic approach, we perform a model space search for Moho variations, P-velocity, and density structure to find an acceptable fit to the three data sets. In order to preferentially sample the good data fit regions, we chose the neighborhood algorithm of Sambridge to optimistically survey the model space. We model the delay times with 3D raytracing using evenly spaced velocity-density nodes. We present here the first results given by this method on synthetic tests. (C) 2011 Elsevier Ltd. All rights reserved.
ISSN: 0098-3004

hal-00643158
https://hal.archives-ouvertes.fr/hal-00643158
DOI : 10.1016/j.cageo.2010.11.017

Éditeur(s) : Elsevier
Résumé : We report on a multidisciplinary study of cold seeps explored in the Central Nile deep-sea fan of the Egyptian margin. Our approach combines in situ seafloor observation, geophysics, sedimentological data, measurement of bottom-water methane anomalies, pore-water and sediment geochemistry, and Th-230/U dating of authigenic carbonates. Two areas were investigated, which correspond to different sedimentary provinces. The lower slope, at similar to 2100 m water depth, indicates deformation of sediments by gravitational processes, exhibiting slope-parallel elongated ridges and seafloor depressions. In contrast, the middle slope, at similar to 1650 m water depth, exhibits a series of debris-flow deposits not remobilized by post-depositional gravity processes. Significant differences exist between fluid-escape structures from the two studied areas. At the lower slope, methane anomalies were detected in bottom-waters above the depressions, whereas the adjacent ridges show a frequent coverage of fractured carbonate pavements associated with chemosynthetic vent communities. Carbonate U/Th age dates (similar to 8 kyr BP), pore-water sulphate and solid phase sediment data suggest that seepage activity at those carbonate ridges has decreased over the recent past. In contrast, large (similar to 1 km(2)) carbonate-paved areas were discovered in the middle slope, with U/Th isotope evidence for ongoing carbonate precipitation during the Late Holocene (since similar to 5 kyr BP at least). Our results suggest that fluid venting is closely related to sediment deformation in the Central Nile margin. It is proposed that slope instability leads to focused fluid flow in the lower slope and exposure of 'fossil' carbonate ridges, whereas pervasive diffuse flow prevails at the unfailed middle slope.
Marine Geology (0025-3227) (Elsevier), 2009-06 , Vol. 261 , N. 1-4 , P. 92-104

Droits : 2009 Elsevier B.V. All rights reserved.
http://archimer.ifremer.fr/doc/2009/publication-6586.pdf
DOI:10.1016/j.margeo.2008.10.008
http://archimer.ifremer.fr/doc/00000/6586/

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We investigate the contribution of atmospheric and its induced non-tidal oceanic loading effects on surface time-varying gravity and tilt measurements for several stations in Western Europe. The ocean response to pressure forcing can be modelled accordingly to the inverted barometer, i.e. assuming that air pressure variations are fully compensated by static sea height changes, or using ocean general circulation models.Wevalidate two runs of theHUGO-mbarotropic ocean model by comparing predicted sea surface height variations with hundred tide-gauge measurements along the European coasts. We then show that global surface pressure field, as well as a barotropic high-resolution ocean model forced by air pressure and winds allow in most cases a significant reduction of the variance of gravity residuals and, to a smaller extends tilt residuals. Wefinally show that precise gravity measurements with superconducting gravimeters allow the observation of large storm surges, occurring in the North Sea, even for inland stations. However, we also confirm that the continental hydrology contribution cannot be neglected. Thanks to their specific sensitivity feature, only tiltmeters closest to the coast can clearly detect the loading due to these storm surges.
ISSN: 0264-3707

hal-00708046
https://hal.archives-ouvertes.fr/hal-00708046
https://hal.archives-ouvertes.fr/hal-00708046/document
https://hal.archives-ouvertes.fr/hal-00708046/file/ETS2008_BOY.pdf
BIBCODE : 2009JGeo...48..182B

Éditeur(s) : HAL CCSD
Résumé : International audience
Trees can control their shape and resist gravity thanks to their ability to produce wood under tensile stress. This stress is known to be produced during the maturation of wood fibres but the mechanism of its generation remains unclear. This study focuses on the formation of the secondary wall in tension wood produced in artificially tilted poplar saplings. Thickness of secondary wall layer (SL) and gelatinous layer (GL) were measured from cambium to mature wood in several trees sampled at different times after tilting. Measurements on wood fibres produced before tilting show the progressive increase of secondary wall thickness during the growing season. After the tilting date, SL thickness decreased markedly from normal wood to tension wood while the total thickness increased compared to normal wood, with the development of a thick GL. However, even after GL formation, SL thickness continues to increase during the growing season. GL thickening was observed to be faster than SL thickening. The development of the unlignified GL is proposed to be a low cost, efficient strategy for a fast generation of tensile stress in broadleaved trees.
IAWA journal / International Association of Wood Anatomists.

hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277
https://hal.archives-ouvertes.fr/hal-01229277/document
https://hal.archives-ouvertes.fr/hal-01229277/file/AbediniClair-Iawa-TensionCellWallThickening_preprint_HAL.pdf
DOI : 10.1163/22941932-00000084