Éditeur(s) : HAL CCSD Elsevier
Résumé : We investigate experimentally the alteration of fractured class-G cement flowed by CO2-rich brine. The experiment mimics a mechanically damaged rough-walled fractured cement annulus at temperature 60 °C and pressure 10 MPa. The experiment consists of flowing a reservoir-equilibrated brine mixed with CO2 (partial pressure of 2.3 MPa) through the fracture of average aperture 14 μm at constant flow rate (100 μL min−1). This flow rate corresponds to pressure gradient representative of an average in situ hydrodynamic condition. Results indicate an intense alteration of the cement with a large removal of mass at the scale of the sample. However, the fracture alteration patterns are triggered by the initial heterogeneity of the fracture aperture; the aperture of the low aperture zones tends to decrease due to calcite precipitation whereas preferential paths develop in the zones of higher aperture associated. Nevertheless, the expected large permeability increase triggered by the mass removal is mitigated by the precipitation of a low density Si-rich amorphous material. The alteration rate will decrease with time because of the increasing distance of diffusion between the fracture where the reactants are actively renewed by advection and the portlandite and C-S-H dissolution fronts. The different zones of reaction can be adequately modeled by a simple 1D diffusion-reaction model using published kinetics coefficients and extrapolation to larger times than the experiment time can be drawn. Altogether, and in addition to the previous studies of the alteration of fractured well cement annulus, this study shows that the leakage potential is strongly controlled by the initial distribution of the aperture along the fracture: low aperture zones will tend to self-heal while localized flow in connected high aperture paths will be perennial.
ISSN: 1750-5836

hal-01346006
https://hal.archives-ouvertes.fr/hal-01346006
DOI : 10.1016/j.ijggc.2016.01.032

Éditeur(s) : HAL CCSD
Résumé : International audience
Metamorphic soles correspond to m to 500 m thick highly strained metamorphic rock units found beneath myloniticbanded peridotites at the base of large-scale ophiolites, as exemplified in Oman. Metamorphic soles aremainly composed of metabasalts deriving from the downgoing oceanic lithosphere and metamorphosed up togranulite-facies conditions by heat transfer from the mantle wedge. Pressure–temperature peak conditions areusually estimated at 1.00.2 GPa and 800100ºC. The absence of HP–LT metamorphism overprint implies thatmetamorphic soles have been formed and exhumed during subduction infancy. In this view, metamorphic soleswere strongly deformed during their accretion to the mantle wedge (corresponding, now, to the base of the ophiolite).Therefore, metamorphic soles and banded peridotites are direct witnesses of the dynamics of early subductionzones, in terms of thermal structure, fluid migration and rheology evolution across the nascent slab interface.Based on fieldwork and EBSD analyses, we present a detailed (micro–) structural study performed on samplescoming from the Sumeini window, the better-preserved cross-section of the metamorphic sole of Oman. Largedifferences are found in the deformation (CPO, grain size, aspect ratio) of clinopyroxene, amphibole and plagioclase,related to mineralogical changes linked with the distance to the peridotite contact (e.g., hardening due to theappearance of garnet and clinopyroxene).To model the incipient slab interface in laboratory, we carried out 5 hydrostatic annealing and simple-shear experimentson Griggs solid-medium apparatus. Deformation experiments were conducted at axial strain rates of 10-6s-1. Fine-grained amphibolite was synthetized by adding 1 wt.% water to a (Mid-Ocean Ridge) basalt powder asa proxy for the metamorphic sole (amphibole + plagioclase + clinopyroxene garnet assemblage). To synthetizegarnet, 2 experiments were carried out in hydrostatic conditions and with deformation at 800C with confiningpressure of 2 GPa. Another simple-shear experiment has been carried out at 800C and 1 GPa with fined-grainednatural garnet. With the aim of mimicking the early slab interface (between the metamorphic sole and bandedperidotites at the base of the ophiolite), 2 simple-shear deformation experiments with 2 layers have been carriedout at 800C and confining pressure of 1 GPa. The bottom layer was made of hydrated basalt powder and the toplayer was made of olivine.Fined-grained garnet-free amphibolite is significantly weaker than dunite but the appearance of harder mineralsin the amphibolite (garnet and clinopyroxene) has major implications on its rheological evolution. These resultsallow liking field observations of strain localization at the interface to the metamorphic sole formation
European Geosciences Union General Assembly 2016
Vienne, Austria

insu-01309394
https://hal-insu.archives-ouvertes.fr/insu-01309394

Éditeur(s) : HAL CCSD
Résumé : International audience
We present an overview of the Mid-Cretaceous hyper-extended rift systemexposed in the northern part of the Pyrenean mountain range. Itsinversion during the Pyrenean orogeny allows for precious observationsof the deep-seated processes occurring at the foot of distal margins.Some peculiar aspects characterizing the pre-Alpine hyper-extended domainare examined throughout the 400 km long suture that is fossilizedin the North Pyrenean Zone (NPZ). The high temperature/low pressure(HT/LP) thermal imprint of the extensional event is studied thanksto a dataset of more than hundred peak temperature measurementsby Raman spectroscopy of the carbonaceous material (RSCM). Thepre- and syn-rift metasediments are characterized by an intense, synmetamorphicductile deformation. Focusing on several key-localitiesof the NPZ, we examine the emplacement conditions of the peridotitesin response to this extreme crustal thinning. Geological evidencessuch as the occurrence of peridotite bodies directly underlying metamorphicpre-rift sediments indicate an early attenuation of the rifted continentalcrust. Moreover, syn-rift, Albian-Cenomanian flysch sequenceswere deposited synchronously with the syn-metamorphic ductile deformationof the pre-rift sequences. All along the Internal MetamorphicZone (IMZ), the base of the flysch deposits also recorded the HT tectonicevent. Such a synchronicity between geological events, which aregenerally separated in time, is not common in mountain belts. We examinehow tectonics, metamorphism and sedimentation may be activein a single basin during extension. We propose an original mechanismfor the evolution of the basins involving continuous basal extraction ofthe pre-rift metamorphic sediments. This early HT deformation eventrelates to the « phase anté-Cénomanienne » described by Pyrenean geologistssince 1930.
24 ème Réunion des sciences de la Terre 2014
Pau, France

insu-01080795
https://hal-insu.archives-ouvertes.fr/insu-01080795

Éditeur(s) : HAL CCSD
Résumé : International audience
Aegean extension is a process driven by slab rollback that, since 45 Ma, shows a twostage evolution. From Middle Eocene to Middle Miocene it is accommodated by localized deformation leading to i) the exhumation of high-pressure metamorphic rocks from mantle to crustal depths, ii) the exhumation of high-temperature rocks in core complexes and iii) the deposition of Paleogene sedimentary basins. Since Middle Miocene, extension is distributed over the whole Aegean domain giving a widespread development of onshore and offshore Neogene sedimentary basins. We reconstructed this two-stage evolution in 3D at Aegean scale by using available ages of metamorphic and sedimentary processes, geometry and kinematics of ductile deformation, paleomagnetic data and available tomographic models. The restorationmodel shows that the rate of trench retreat was around 0.6 cm/y during the first 30 My and then accelerated up to 3.2 cm/y during the last 15 My. The sharp transition observed in the mode of extension, localized versus distributed, which occurred in Middle Miocene correlates with the acceleration of trench retreat and is more likely a consequence of the Hellenic slab tearing documented by mantle tomography. The development of large dextral NE-SW strike-slip faults during the second stage of Aegean extension, since Middle Miocene, is illustrated by the 450 Km-long fault, recently put in evidence, offshore from Myrthes to Ikaria and onshore from Izmir to Balikeshir, in western Anatolia. Therefore, the interaction between the Hellenic trench retreat and the westward displacement of Anatolia started in Middle Miocene,almost 10 Ma before the propagation of the North Anatolian Fault in the North Aegean. This raises a fundamental issue concerning the dynamic relationship between slab tearing and Anatolia displacement
ISSN: 0438-9557

insu-01574659
https://hal-insu.archives-ouvertes.fr/insu-01574659
https://hal-insu.archives-ouvertes.fr/insu-01574659/document
https://hal-insu.archives-ouvertes.fr/insu-01574659/file/EFFECTS_OF_SLAB_ROLLBACK_ACCELERATION_ON_AEGEAN_EX.pdf
DOI : 10.12681/bgsg.11697

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
A San Carlos olivine polycrystal has been deformed under uppermost mantle conditions, by compression at 900 °C, at a strain rate of 1.1 × 10−5 s−1, under a confining pressure of 300 MPa, using the Paterson press. Transmission electron tomography of dislocations has been performed by scanning transmission electron microscopy, by conventional transmission electron microscopy using the weak-beam dark-field technique, associated with precession or not, in order to determine the glide planes of [001] screw dislocations. This recent technique is the most suitable one since most [001] dislocations exhibit straight screw segments due to the high lattice friction on this character at low temperature. We find that [001] dislocations glide in (100), (010) and {110} as already reported, but also more unexpectedly in {120} and {130}. We show that at 900 °C, [001] {110} glide is dominant in polycrystals. We have, however, noted and characterized numerous cross-slip events in the specimen.
ISSN: 0342-1791

hal-01054330
https://hal.archives-ouvertes.fr/hal-01054330
DOI : 10.1007/s00269-014-0665-1

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We report chlorine (Cl) and fluorine (F) abundances in minerals, interstitial glasses, and melt inclusions in 12 andesite-hosted, spinel harzburgite xenoliths and crosscutting pyroxenite veins exhumed from the sub-arc lithospheric mantle beneath Avacha volcano in the Kamchatka Arc (NE Russia). The data are used to calculate equilibrium mineral-melt partition coefficients (Dmineral/meltDmineral/melt) for Cl and F relevant to subduction-zone processes and unravel the history of volatile depletion and enrichment mechanisms in an arc setting.Chlorine is ∼100 times more incompatible in pyroxenes (View the MathML sourceDClmineral/melt = 0.005–0.008 [±0.002–0.003]) than F (View the MathML sourceDFmineral/melt = 0.50–0.57 [±0.21–0.24]), which indicates that partial melting of mantle sources leads to strong depletions in Cl relative to F in the residues. The data set in this study suggests a strong control of melt composition on View the MathML sourceDCl,Fpyroxene/melt, in particular H2O contents and Al/(Al + Si), which is in line with recent experiments. Fluorine is compatible in Ca-amphibole in the ‘wet’ sub-arc mantle (View the MathML sourceDFamphibole/melt = 3.5–3.7 [±1.5]) but not Cl (View the MathML sourceDClamphibole/melt = 0.03–0.05 [±0.01–0.03]), indicating that amphibole may fractionate F from Cl in the mantle wedge. The inter-mineral partition coefficients for Cl and F in this study are consistent amongst different harzburgite samples, whether they contain glass or not. In particular, disseminated amphibole hosts much of the Cl and F bulk rock budgets of spinel harzburgites (View the MathML sourceDClamphibole/pyroxene up to 14 and View the MathML sourceDFamphibole/pyroxene up to 40). Chlorine and fluorine are variably enriched (up to 1500 ppm Cl and 750 ppm F) in the parental arc picrite and boninite melts of primitive pyroxenite veins (and related melt inclusions) crosscutting spinel harzburgites.Based on the data in this study, the main inferences on the behaviour of Cl and F during melting and metasomatic processes in the sub-arc mantle are as follow:(i) Melting models show that most depleted mantle protoliths of intra-oceanic arc sources can have extremely low Cl/F (0.002–0.007) before being overprinted by subduction-derived components.(ii) Chlorine has a higher percolation distance in the mantle than F. Even for small fluid or melt volumes, Cl and F signatures of partial melting are overprinted by those of pervasive percolation, which increases Cl/F in percolating agents and bulk peridotites during chromatographic interaction and/or amphibole-forming metasomatic reactions. These processes ultimately control the bulk Cl and F compositions of the residual mantle lithosphere beneath arcs, and likely in other tectonic settings.(iii) Fluxed melting models suggest that Cl enrichment in arc picrite and boninite melts in this study, and in many arc melt inclusions reported in the literature, could be related to the infiltration of high Cl/F fluids derived from subducted serpentinite or altered crust in mantle wedge sources. However, these high Cl/F signatures should be re-evaluated with new models in light of the possible overprint of pervasive percolation effects in the mantle. The breakdown of amphibole (and/or mica) in the deep metasomatised mantle at higher pressure and temperature conditions than in the slab may explain, at least in part, the positive correlations between F abundances and Cl/F in primitive arc melt inclusions and slab depth.
ISSN: 0016-7037

hal-01553610
https://hal.archives-ouvertes.fr/hal-01553610
DOI : 10.1016/j.gca.2016.10.035

Éditeur(s) : HAL CCSD Geological Society
Résumé : International audience
We constrain the slip and cooling history of the Mykonos detachment footwall using thermochronometry. A U-Pb zircon age of 13.5 +/- 0.3 Ma dates intrusion of the Mykonos monzogranite. Ar-40/ Ar-39 homblende and biotite ages from the monzogranite are 12.7 +/- 0.6 Ma and 10.9 +/- 0.6 Ma, whereas zircon and apatite fission-track ages range from 13 +/- 0.8 Ma to 10.7 +/- 0.8 Ma and 12.5 +/- 2.2 Ma to 10.5 +/- 1.8 Ma. (U-Th)/He ages range from 13.6 +/- 0.6 Ma to 9.0 +/- 0.7 Ma for zircon and 11. +/- 10.5 Ma to 8.9 +/- 0.4 Ma for apatite. The ages in part overlap within 2 sigma errors and together with the long apatite fission-track lengths (>14 mu m) support rapid cooling at rates > 100 degrees C Ma(-1). The low-temperature thermochronometric ages decrease east-northeastwards in the direction of hanging-wall transport on the Mykonos detachment. Age-distance relationships show that the Mykonos detachment slipped at an average rate of 6.0 + 9.2/-2.4 km Ma(-1) c. 30 km of offset and c. 12 km of exhumation. This result indicates that Miocene low-angle normal faulting was not important for the exhumation of the Cycladic blueschist unit. The opening of the Aegean Sea basin in the Miocene was controlled by a few large-magnitude low-angle normal faults.
ISSN: 0016-7649

hal-00412177
https://hal.archives-ouvertes.fr/hal-00412177
DOI : 10.1144/0016-76492006-145

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We report concentrations of hydrogen (H) in upper mantle minerals of peridotites (olivine and pyroxenes) transported by alnöitic lavas, which erupted on the southwestern border of the Ontong Java Plateau (Malaita, Solomon Islands, West Pacific). Unpolarized FTIR analyses show that olivine, orthopyroxene, and diopside contain 2–32 ppm, 162–362 ppm and 159–459 ppm wt H2O, respectively. In the studied lherzolites, garnets are anhydrous. The concentration of hydrogen within individual olivine and pyroxene grains is almost homogeneous, indicating no evidence of dehydration or hydration by ionic diffusion. In the lherzolite, the concentration of hydrogen in olivine tends to increase weakly with depth (based on geothermobarometry), consistent with the increase of water solubility with increasing water fugacity as a function of pressure, but concentrations remain well below water-saturation values determined experimentally. The highest concentration of H in olivine (32 ppm wt H2O) is, however, found in refractory spinel harzburgites, which equilibrated at depths of 85 km., while deeper specimens as the high-temperature spinel harzburgites, and some of the garnet lherzolites, contain less hydrogen in olivine. Olivines from pyroxene- or pargasite-rich peridotites have also lower hydrogen concentrations. We interpret the high hydrogen concentrations in olivine from the refractory spinel harzburgites as due to (1) simultaneous hydration and metasomatism of the lithospheric mantle by a water-rich silicate melt/fluid, during which hydrogen follows MREE and where spinel harzburgite have experienced ‘stealth’ metasomatism, and/or (2) to a late ‘fleeting’ hydrogen metasomatism, which would hydrate the rock after this first ‘stealth’ metasomatism event. In the second case, the composition of the ‘fleeting’ percolating fluid (small volume fraction of very evolved fluids, with high volatiles concentration and transient properties) is likely to be linked to the decrease of the plume activity and resulting in the downwelling of the lithosphere asthenosphere boundary. The difference in hydrogen concentration between harzburgites and lherzolites could be linked to variation in trace elements in olivine induced by the first ‘stealth’ metasomatism alone or associated to the late ‘fleeting’ hydrogen metasomatism, triggered by the lack of secondary crystallization of clinopyroxenes in the harzburgite. To conclude, H concentrations in upper mantle minerals may thus be correlated to metasomatic events, with the later yielding variation of the mineral assemblage and trace element composition that constitute the peridotites.
ISSN: 0024-4937

hal-01143385
https://hal.archives-ouvertes.fr/hal-01143385
DOI : 10.1016/j.lithos.2014.11.005

Éditeur(s) : Elsevier
Résumé : A previously unknown pattern of multiple bottom-simulating reflections (BSRs) occurs on high-resolution reflection seismic data in the Danube deep-sea fan, associated with acoustic features indicating free gas. Our study provides evidence that this pattern is developed in relation with the architecture of distinct channel-levee systems of the Danube fan. Channel-levee systems hosting multiple BSRs act as relatively sealed gas-bearing systems whose top is situated above the base of the gas hydrate stability zone (BGHSZ). Inside these systems, free gas accumulates below the BGHSZ under a combined lithological, structural and stratigraphical control. The uppermost BSR marks the current equilibrium BGHSZ, for a gas composition of more than 99% methane. Model-derived depths of the BGHSZ for different gas compositions and pressure-temperature conditions show that multiple BSRs would correspond to the BGHSZ either for (1) layers of gas hydrates with high contents of heavy hydrocarbons or hydrogen sulphide, or (2) stable climatic episodes with temperatures between glacial values and the present-day conditions. As the gas hydrate compositions required by hypothesis (I) are in sharp contradiction with the general background of the gas composition in the study area, we suggest that multiple BSRs are most probably relics of former positions of the BGHSZ, corresponding to successive steps of climate warming. In this case, they can provide sea-bottom paleotemperature values for these episodes, and hence they are potential new proxies for deciphering past climate conditions.
Marine Geology (0025-3227) (Elsevier), 2006-03 , Vol. 227 , N. 3-4 , P. 163-176

Droits : 2006 Elsevier B.V. All rights reserved
http://archimer.ifremer.fr/doc/2006/publication-1210.pdf
DOI:10.1016/j.margeo.2005.12.006
http://archimer.ifremer.fr/doc/00000/1210/

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Sensitive instruments like strainmeters and tiltmeters are necessary for measuring slowly varying low amplitude Earth deformations. Nonetheless, laser and fibre interferometers are particularly suitable for interrogating such instruments due to their extreme precision and accuracy. In this paper, a practical design of a simple pendulum borehole tiltmeter based on laser fibre interferometric displacement sensors is presented. A prototype instrument has been constructed using welded borosilicate with a pendulum length of 0.85 m resulting in a main resonance frequency of 0.6 Hz. By implementing three coplanar extrinsic fibre Fabry-Perot in-terferometric probes and appropriate signal filtering, our instrument provides tilt measurements that are insensitive to parasitic deformations caused by temperature and pressure variations. This prototype has been installed in an underground facility (Rustrel, France) where results show accurate measurements of Earth strains derived from Earth and ocean tides, local hydro-logic effects, as well as local and remote earthquakes. The large dynamic range and the high sensitivity of this tiltmeter render it an invaluable tool for numerous geophysical applications such as transient fault motion, volcanic strain and reservoir monitoring.
ISSN: 0956-540X

hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967
https://hal.archives-ouvertes.fr/hal-01265967/document
https://hal.archives-ouvertes.fr/hal-01265967/file/HCS1.pdf
DOI : 10.1093/gji/ggv358

Éditeur(s) : HAL CCSD Mineralogical Society of America
Résumé : International audience
To test if hydrogen incorporation by ionic diffusion can occur between a volatile-rich kimberlitic liquid and forsterite, results of high-pressure and high-temperature experiments using a piston-cylinder apparatus at 1200–1300 °C and 1 GPa for durations of 1 min, 5 h, and 23 h, are reported here. Kimberlitic liquid in the system CaO-MgO-Al2O3-SiO2-CO2-H2O and synthetic forsterite single crystals were chosen as a first simplification of the complex natural kimberlite composition. Unpolarized Fourier transform infrared spectroscopy was used to quantify the concentrations of OH in the crystallographically oriented forsterite. Scanning electron microscopy, electron backscattered diffraction, electron microprobe analyses, and transmission electron microscopy were performed to identify the run products. After 5 and 23 h, a forsterite overgrowth crystallized with the same orientation as the initial forsterite single crystal. The kimberlitic liquid has crystallized as micrometer-scale euhedral forsterite neocrystals with random crystallographic orientations, as well as a nanoscale aluminous phase and a calcic phase. Despite theoretical water-saturation of the system and long duration, none of the initial forsterite single crystals display signs of hydration such as hydrogen diffusion profile from the border toward the center of the crystal. Most likely, the presence of CO2 in the system has lowered the H2O fugacity to such an extent that there is no significant hydration of the starting forsterite single crystal or its overgrowth. Also, the presence of CO2 enhances rapid forsterite crystal growth. Forsterite growth rate is around 2 × 108 μm3/h at 1250 °C. These experimental results suggest a deep mantle origin of the high OH content found in natural mantle-derived xenoliths transported in kimberlites, as reported from the Kaapvaal craton. In agreement with previous studies, it also points out to the fact that significant hydration must take place in a CO2-poor environment.
ISSN: 0003-004X

hal-01217157
https://hal.archives-ouvertes.fr/hal-01217157
DOI : 10.2138/am-2015-5200

Éditeur(s) : HAL CCSD Elsevier
Résumé : We have studied the phase transformation of forsterite to wadsleyite under shear stress at the Earth's transition zone pressure and temperature conditions. Two-step experiments were performed using a multi-anvil press. First, we hot pressed iron-free forsterite at 6 or 11 GPa and 1100 degrees C. Then we deformed a slab of this starting material using a direct simple shear assembly at 16 GPa and 1400 degrees C for 1, 15, 35, 40, or 60 min. Both the starting material and the deformed samples were characterized using optical and scanning electron microscopy including measurements of crystal preferred orientations (CPO) by electron back scattered diffraction (EBSD), transmission electron microscopy (TEM), and Fourier transform infrared spectroscopy (FTIR). The phase transformation occurs very rapidly, in less than 1 min, and metastable forsterite relics are not observed after deformation. The grain size of wadsleyite is slightly smaller than the forsterite starting material. The water contents obtained from FTIR analyses in forsterite and wadsleyite are 65-124 wt ppm H2O and 114-736 wt ppm H2O, respectively, which are well below water solubility at similar conditions in the presence of free water. Wadsleyite aggregates display weak CPO patterns with [1 0 0] axes concentrated at low angle to the shear direction, [0 1 0] axes perpendicular to the shear plane and nearly random [0 0 1] axes. Only a few dislocations were observed in wadsleyite with TEM. This observation is consistent with the assumption that most dislocations formed during the initial high-stress stages of these stress-relaxation experiments, were consumed in the phase transformation, probably enhancing the transformation rate. CPO patterns vary as a function of the water content: with increasing water content the density of [1 0 0] axes parallel to the shear direction decreases, and the density of [0 0 1] axes increases. Viscoplastic self-consistent modeling of CPO evolution using previously reported glide systems for wadsleyite, i.e., [1 0 0]{0 k 1} and 1/2 (1 1 1){1 0 1}, cannot reproduce the measured CPO, unless the [0 0 1](0 1 0) system, for which dislocations have not been observed by TEM, is also activated. In addition, wadsleyite grain growth suggests the participation of diffusion-assisted processes in deformation. Calculated anisotropies for P and S-waves using measured CPO are always below 1%. This very low anisotropy is due to both the low finite strain achieved in the experiments, which leads to weak wadsleyite CPO, and to the diluting effect of added majorite. The present experiments emphasize the importance of stress, grain size evolution and water content in the forsterite to wadsleyite phase transformation and subsequent deformation in the transition zone.
ISSN: 0031-9201

hal-00617430
https://hal.archives-ouvertes.fr/hal-00617430
DOI : 10.1016/j.pepi.2010.11.001

Éditeur(s) : HAL CCSD National Research Council Canada
Résumé : International audience
Back-arc extension in the Aegean, which was driven by slab rollback since 45 Ma, is described here for the first time in two stages. From Middle Eocene to Middle Miocene, deformation was localized leading to i) the exhumation of high-pressure metamorphic rocks to crustal depths, ii) the exhumation of high-temperature metamorphic rocks in core complexes and iii) the deposition of sedimentary basins. Since Middle Miocene, extension distributed over the whole Aegean domain controlled the deposition of onshore and offshore Neogene sedimentary basins. We reconstructed this two-stage evolution in 3D and four steps at Aegean scale by using available ages of metamorphic and sedimentary processes, geometry and kinematics of ductile deformation, paleomagnetic data and available tomographic models. The restoration model shows that the rate of trench retreat was around 0.6 cm/y during the first 30 My and then accelerated up to 3.2 cm/y during the last 15 My. The sharp transition observed in the mode of extension, localized versus distributed, in Middle Miocene correlates with the acceleration of trench retreat and is likely a consequence of the Hellenic slab tearing documented by mantle tomography. The development of large dextral NE-SW strike-slip faults, since Middle Miocene, is illustrated by the 450 Km-long fault zone, offshore from Myrthes to Ikaria and onshore from Izmir to Balikeshir, in western Anatolia. Therefore, the interaction between the Hellenic trench retreat and the westward displacement of Anatolia started in Middle Miocene, almost 10 Ma before the propagation of the North Anatolian Fault in the North Aegean.
ISSN: 0008-4077

insu-01271296
https://hal-insu.archives-ouvertes.fr/insu-01271296
https://hal-insu.archives-ouvertes.fr/insu-01271296/document
https://hal-insu.archives-ouvertes.fr/insu-01271296/file/Brun%20etal%20CJES%202016.pdf
DOI : 10.1139/cjes-2015-0203

Éditeur(s) : HAL CCSD
Résumé : National audience
New experimental data on electrical and anelastic properties of oceanic rocks at high pressures and temperatures are compared with the field data of seismic and electrical anomalies observed at oceanic spreading centers. The laboratory results of electrical conductivity and internal friction on gabbro and peridotites permit to estimate a degree of partial melting and maximum temperature in axial magma chambers (12-15% of melting at 1155-1165°C) and at the upper boundary of a source zone at the depth of 40-90 km (less than 5% of melting in the absence of pyroxene crystals and up to 11-14% in the pyroxene reach rocks at 1360-1370°C) at mid-oceanic ridges.
ISSN: 0934-6554

hal-01322920
http://hal.univ-reunion.fr/hal-01322920

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The ‘International Intercomparison Exercise of fCO₂ Systems’ was carried out in 1996 during the R/V Meteor Cruise 36/1 from Bermuda/UK to Gran Canaria/Spain. Nine groups from six countries (Australia, Denmark, France, Germany, Japan, USA) participated in this exercise, bringing together 15 participants with seven underway fugacity of carbon dioxide (fCO₂) systems, one discrete fCO₂ system, and two underway pH systems, as well as systems for discrete measurement of total alkalinity and total dissolved inorganic carbon. Here, we compare surface seawater fCO₂ measured synchronously by all participating instruments. A common infrastructure (seawater and calibration gas supply), different quality checks (performance of calibration procedures for CO2, temperature measurements) and a common procedure for calculation of final fCO₂ were provided to reduce the largest possible amount of controllable sources of error. The results show that under such conditions underway measurements of the fCO₂ in surface seawater and overlying air can be made to a high degree of agreement (±1 μatm) with a variety of possible equilibrator and system designs. Also, discrete fCO₂ measurements can be made in good agreement (±3 μatm) with underway fCO₂ data sets. However, even well-designed systems, which are operated without any obvious sign of malfunction, can show significant differences of the order of 10 μatm. Based on our results, no “best choice” for the type of the equilibrator nor specifics on its dimensions and flow rates of seawater and air can be made in regard to the achievable accuracy of the fCO₂ system. Measurements of equilibrator temperature do not seem to be made with the required accuracy resulting in significant errors in fCO₂ results. Calculation of fCO₂ from high-quality total dissolved inorganic carbon (CT) and total alkalinity (AT) measurements does not yield results comparable in accuracy and precision to fCO₂ measurements.
ISSN: 0304-4203

hal-01245605
https://hal.archives-ouvertes.fr/hal-01245605
DOI : 10.1016/S0304-4203(00)00080-3

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Subduction infancy corresponds to the first few million years following subduction initiation, when slabs start their descent into the mantle. It coincides with the transient (yet systematic) transfer of material from the top of the slab to the upper plate, as witnessed by metamorphic soles welded beneath obducted ophiolites. Combining structure–lithology–pressure–temperature–time data from metamorphic soles with flow laws derived from experimental rock mechanics, this study highlights two main successive rheological switches across the subduction interface (mantle wedge vs. basalts, then mantle wedge vs. sediments; at ∼800 °C and ∼600 °C, respectively), during which interplate mechanical coupling is maximized by the existence of transiently similar rheologies across the plate contact. We propose that these rheological switches hinder slab penetration and are responsible for slicing the top of the slab and welding crustal pieces (high- then low-temperature metamorphic soles) to the base of the mantle wedge during subduction infancy. This mechanism has implications for the rheological properties of the crust and mantle (and for transient episodes of accretion/exhumation of HP-LT rocks in mature subduction systems) and highlights the role of fluids in enabling subduction to overcome the early resistance to slab penetration.
ISSN: 0012-821X

hal-01383368
http://hal.upmc.fr/hal-01383368
http://hal.upmc.fr/hal-01383368/document
http://hal.upmc.fr/hal-01383368/file/Agard_2016_Plate_interface.pdf
DOI : 10.1016/j.epsl.2016.06.054

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
The seismic anisotropy of the deep Earth is reviewed as a profile from the upper mantle to the solid inner core at the centre of the Earth. The upper mantle is by far the most anisotropic region of the Earth, followed the D” layer above the core mantle boundary. In contrast it is shown that many minerals that are present in the upper mantle, transition zone, lower mantle, D” layer and solid inner core are elastically anisotropic to different degrees. The anisotropy of hydrous phases present in subduction zones is briefly introduced. The basic concepts of single crystal and polycrystalline elasticity and the extrapolation of elastic properties to high temperature and pressure are presented. The specific features of elastic wave propagation in an anisotropic medium of any arbitrary symmetry are illustrated using mantle and inner core phases. The roles of crystal preferred orientation, water and melt in producing seismic anisotropy in the upper mantle are discussed.
Treatese of Geophysics, vol.2

hal-00408321
https://hal.archives-ouvertes.fr/hal-00408321
DOI : 10.1016/B978-044452748-6.00045-6

Éditeur(s) : HAL CCSD
Résumé : International audience
Aegean extension is a process driven by slab rollback that since 45 Ma shows a two-stage evolution. From 45 to13 Ma it is accommodated by localized deformation leading to i) the exhumation of high-pressure metamorphicrocks from mantle to crustal depths, ii) the exhumation of high-temperature rocks in core complexes and iii) thedeposition of Paleogene sedimentary basins. Since 13 Ma, extension is distributed over the whole Aegean domaingiving a widespread development of onshore and offshore Neogene sedimentary basins. The 3D reconstruction atAegean scale of this two-stage evolution shows that the rate of trench retreat was around 0.6 cm/y during the first30 My and then accelerated up to 3.2 cm/y during the last 13 My. Using available tomographic evidence, timingof metamorphic and sedimentary processes, paleomagnetic data and geometry and kinematics of deformation, wepropose that the sharp transition in trench retreat and deformation mode, localized vs distributed, at 13 Ma wascontrolled to slab tearing. Moreover, the development of dextral NE-SW strike-slip faults and related pull-apartbasins in the North Aegean domain, from the Cyclades to the Rhodope, strongly suggests that this sharp transitionalso corresponds to the onset of Anatolia westward escape.
Geophysical Research Abstracts
Vienne, Austria

insu-01137631
https://hal-insu.archives-ouvertes.fr/insu-01137631

Éditeur(s) : HAL CCSD American Geophysical Union (AGU)
Résumé : International audience
In south China the Lushan massif forms a topographic high of the South China Block south of the Qinling-Dabie belt. The Lushan massif consists of two main lithotectonic units separated by a major tectonic contact: a Neoproterozoic (upper Sinian)-Paleozoic unit comprising primarily unmetamorphosed sandstones overlies a Paleoproterozoic unit mainly composed of low-pressure, high-temperature gneisses and micaschists. Both units are cut by Cretaceous granitic intrusions. Three primary tectono-metamorphic and magmatic events are recognized. The eastern part of the Lushan massif is cut by a NNE-SSW trending ductile normal fault (D3 deformation) coeval to the emplacement of a 100-110 Ma leucogranite dated by 40Ar/39Ar laserprobe on biotite and muscovite. D2 deformation is responsible for the formation of a decakilometer-scale NE-SW trending upright anticline characterized by NE-SW stretching and NW-SE shortening. The age of this folding event is defined by a 127±1 (2σ) Ma U/Pb titanite date obtained for a syntectonic granodiorite and 40Ar/39Ar ages of 133 Ma for amphibole. This Cretaceous age also corresponds to the 40Ar/39Ar ages of 126 Ma found on syntectonic muscovites at the base of the Sinian unit. An older deformation event, D1, characterized by a top-to-the-NW extensional decollement of the Sinian-Paleozoic series above Proterozoic metamorphic rocks is related to the Triassic tectonics of the Dabieshan. Lastly, in the lower part of Sinian rocks, the occurrence of kyanite cataclased during D1 documents an older, poorly preserved, late Paleozoic-early Mesozoic tectonometamorphic event (Dx) related to a blind thrust in the continental crust of the South China Block in the southern foreland of the Dabieshan.
ISSN: 0278-7407

insu-00717721
https://hal-insu.archives-ouvertes.fr/insu-00717721
https://hal-insu.archives-ouvertes.fr/insu-00717721/document
https://hal-insu.archives-ouvertes.fr/insu-00717721/file/Lin-Tectonics-2000.pdf
DOI : 10.1029/2000TC900009

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Alpine Corsica consists of a stack of variably metamorphosed units of continental and Tethys-derived rocks. It represents an excellent example of high-pressure (HP) orogenic belt, such as the Western Alps, exposed over a small and accessible area. Compared to the Western Alps, the geology of Alpine Corsica is poorly unraveled. During the 1970s-80s, based on either lithostratigraphic or metamorphic field observations, various classifications of the belt have been proposed, but these classifications have been rarely matched together. Furthermore, through time, the internal complexity of large domains has been progressively left aside in the frame of large-scale geodynamic reconstructions. As a consequence, major open questions on the internal structure of the belt have remained unsolved. Apart from a few local studies, Alpine Corsica has not benefited of modern developments in petrology and basin research. This feature results in several uncertainties when combining lithostratigraphic and metamorphic patterns and, consequently, in the definition of an exhaustive architecture of the belt. In this paper we provide a review on the geology of Alpine Corsica, paying particular attention to the available lithostratigraphic and metamorphic classifications of the metamorphic terranes. These data are completed by a new and exhaustive metamorphic dataset obtained by means of thermometry based on Raman Spectroscopy of Carbonaceous Material (RSCM). This technique provides reliable insights on the peak temperature of the metamorphic history for CM-bearing metasediments. A detailed metamorphic characterization of metasediments, which have been previously largely ignored due to retrogression or to the lack of diagnostic mineralogy, is thus obtained and fruitfully coupled with the available lithostratigraphic data. Nine main tectono-metamorphic units are defined, from subgreenschist (ca. 280-300 °C) to the lawsonite-eclogite-facies (ca. 500-550 °C) condition. These units are homogeneous in metamorphism, laterally continuous and have characteristic lithostratigraphic features. This study also suggests a direct link between the pre-orogenic extensional setting and the present-day compressional structure of Alpine Corsica, indicating that large sections of subducted lithosphere were subducted and exhumed as coherent domains. These features provide important insight on the mechanism of stacking and exhumation of HP rocks, and make Alpine Corsica a unique reference for mountain-building processes in Tethyan-type orogens.
ISSN: 0012-8252

hal-00814433
https://hal.archives-ouvertes.fr/hal-00814433
DOI : 10.1016/j.earscirev.2012.10.003