Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
From outcrops located in Provence (South-East France), we describe the distribution, the microstructures, and the petrophysical properties of deformation band networks related to both contractional and extensional tectonic events. In contraction, pervasively distributed networks of reverse-sense compactional shear bands are observed in all folded sand units of the foreland, whereas localized networks of clustered reverse-sense shear bands are only observed close to a large-scale thrust. In extensional setting, networks of clustered normal-sense shear bands are generally observed adjacent to map-scale faults (100 m–10 km scale), although some randomly distributed bands are also observed between these faults. Normal-sense cataclastic faults, i.e. zone of deformation bands containing a localized slip-surface, are also observed to be restricted to sand units, suggesting that faults initiated in the sands during extension, but not during contraction. Shear bands and faults show cataclastic microstructures with high-permeability reduction whereas compactional shear bands show crush microbreccia or protocataclastic microstructures with moderate permeability reduction. This basin-scale analysis underlines the major role of tectonic settings (thrust-fault versus normal-fault andersonian-stress regime) and the influence of inherited large-scale faults on the formation/localization of low-permeability shear bands. We also provide a geometrical analysis of the band network properties (spacing, thickness, shear/compaction ratio, degree of cataclasis, petrophysical properties) with respect to the median grain size, porosity and grain sorting of host sand. This analysis suggests that grain size, although less important than stress-state conditions and the presence of large-scale faults, has a non-negligible effect on band network geometry. No correlations are observed between the grain sorting, porosity and band network geometry.
ISSN: 0264-8172

hal-01116421
https://hal.archives-ouvertes.fr/hal-01116421
DOI : 10.1016/j.marpetgeo.2013.12.020

Éditeur(s) : HAL CCSD Mineralogical Society of America
Résumé : International audience
In situ mineralization of CO2 in ultramafic rock-hosted aquifers is one of the promising solutions for decreasing CO2 concentrations in the atmosphere. Naturally altered ultramafic rocks suggest that carbonation processes are controlled by local heterogeneities in the structure of the rock and fluid transport at the water-rock interfaces. We studied the role of rock crystallographic anisotropy relative to the global fluid flow direction on the mineralization of CO2 by means of electron microscope analyses from the macro- to the micrometer scale (EBSD-FIB). The sample used for the measurements was a hot pressed olivine core percolated by water enriched in CO2 (pCO2 = 10 MPa) at 180 °C. During the percolation experiment, olivine was dissolved and two types of carbonates, dolomite, and magnesite, were precipitated on olivine surfaces. The results showed that the dissolution of olivine is controlled by its crystallographic properties as shown by the development of etch-pits only on the (010)ol planes and with elongated shapes parallel to the [010]ol axes. In contrast, the precipitation of carbonates is governed by hydrodynamic properties. Carbonates are heterogeneously distributed in the percolated rock. They are mainly located along the moderate (for dolomite) and the minor (for magnesite) flow paths, both oriented parallel to the principal fluid flow direction, which allow carbonates to be supplied with divalent cations (e.g., Ca2+, Mg2+, and Fe2+). In these flow paths, carbonate growth is systematically oriented normal to the flow that facilitates the development of chemical gradients with cationic supersaturation conditions for carbonate precipitation near the walls.In natural systems, the (010)ol planes are parallel to the Moho and the (100)ol planes are vertical; our study suggests that flow of CO2-rich fluids will induce precipitation of carbonates localized along, and preferentially clogging, vertical flow paths while favoring olivine dissolution along horizontal fluid pathways. This dual control of structure and fluid flow on carbonation mechanisms could be an important parameter allowing sustainable CO2 storage in peridotites, while limiting the risks of leakage toward the surface.
ISSN: 0003-004X

hal-01143393
https://hal.archives-ouvertes.fr/hal-01143393
DOI : 10.2138/am-2015-4913

Éditeur(s) : HAL CCSD AGU and the Geochemical Society
Résumé : International audience
Numerical models show that small-scale convection (SSC) occurring atop a mantle plume is a plausible mechanism to rejuvenate the lithosphere. The triggering of SSC depends on the density contrast and on the rheology of the unstable layer underlying the stagnant upper part of the thermal boundary layer (TBL). Partial melting may change both properties. We analyze, using 2-D numerical simulations, how partial melting influences the dynamics of time-dependent SSC instabilities and the resulting thermo-mechanical rejuvenation of an oceanic plate moving atop of a plume. Our simulations show a complex behavior, with acceleration, no change, or delay of the SSC onset, due to competing effects of the latent heat of partial melting, which cools the plume material, and of the buoyancy increase associated with both melt retention and depletion of residue following melt extraction. The melt-induced viscosity reduction is too localized to affect significantly SSC dynamics. Faster SSC triggering is promoted for low melting degrees (low plume temperature anomalies, thick lithosphere, or fast moving plates), which limit both the temperature reduction due to latent heat of melting and the accumulation of depleted buoyant residue in the upper part of the unstable layer. In contrast, high partial melting degrees lead to a strong temperate decrease due to latent heat of melting and development of a thick depleted layer within the sublithospheric convecting layer, which delay the development of gravitational instabilities. Despite differences in SSC dynamics, the thinning of the lithosphere is not significantly enhanced relatively to simulations that neglect partial melting.
ISSN: 1525-2027

hal-01277175
https://hal.archives-ouvertes.fr/hal-01277175
DOI : 10.1002/2015GC005967

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : International audience
Few studies have investigated the influence of environmental conditions on the within-treevariation in Eucalyptus wood traits. The genotype and environment effects and their interactionsinfluence the wood properties. Their evaluations are crucial to estimate the genotype values andto select with efficiency. Thus, the aim of this study was to better understand the effect ofground slope and wind speed on the spatial variation of basic density (ρ), stiffness (MOE) andmicrofibril angle (MFA) of Eucalyptus wood. Wood discs cut along the trunk were sampledfrom 150 six-year-old Eucalyptus grandis x E. urophylla hybrids growing in 3 contrastinggrowing conditions influenced by ground slope and wind regime. Near Infrared (NIR)calibrations previously developed for ρ, MOE and MFA were used to predict in our discs. 2-Dplots presenting the spatial variation of predicted wood traits were compared. The higher theground slope, the greater the magnitude of radial variation in ρ, principally in the medium zoneof the trunk. The spatial variation of wood stiffness seems to be sensitive to two environmentalconditions. The MFA radial decreases were more pronounced where the wind speed was higher.At the base and top of the trees, however, there was no significant effect of growing conditionson the radial variation of the wood properties considered here.
ISSN: 0931-1890

hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896
https://hal.archives-ouvertes.fr/hal-01451896/document
https://hal.archives-ouvertes.fr/hal-01451896/file/Art_Gril_al_Spatial_variation_wood_density_2016.pdf
DOI : 10.1007/s00468-015-1327-8

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
A reactive percolation experiment was conducted by injecting seawater into a permeable olivine aggregate at 190 °C and 19 MPa to explore the relationships between hydration reactions and hydrodynamic properties during the onset of serpentinization in the ultramafic lithosphere exposed at mid-ocean ridges. The experiment was stopped after 23 days when the sample became impermeable. The initial flow rate was 0.2 mL/h and then was decreased down to 0.06 mL/h after 8 days. Permeability decreased continuously throughout the experiment. The analyses of fluid chemistry time series and of the mineralogy and structure of the reacted sample showed olivine dissolution and precipitation of proto-serpentine, brucite and Fe-oxides. These reactions are controlled by coupled hydrodynamic and chemical processes interacting at different time and spatial scales. Their first characteristic is the production of silica rich outlet fluids in disequilibrium with the observed reacted mineral assemblages. These compositions are interpreted as resulting from a suite of coupled dissolution-precipitation reactions, controlled at the pore scale by surface kinetic processes, that rapidly reaches steady-state (constant fluid composition independent of fluid flux). Hence, the effective rate of serpentinization was controlled, to the first order, by the transport of reactants during the experiment. Mass balance calculations show that the rate of olivine conversion was fast (0.2-0.5 wt%/day), yet only ∼8 wt% of the olivine sample reacted, because the permeability drop limited fluid circulation. Porosity varied little during the experiment compared to permeability changes: the decrease of permeability was explained by the structure of the newly formed serpentine favouring the clogging of fluid paths. The rate at which permeability decreased was the fastest at low flux conditions. This suggests that permeability changes were not controlled simply by the kinetics of the serpentinization reactions, but mainly reflected the development of low Peclet pore scale zones forming micro-environments that control the serpentinization reaction-paths. These results outline the need to take into account the coupling of hydrodynamic and chemical processes when modelling the effects of reactive transport within the hydrating oceanic lithosphere.
ISSN: 0012-821X

hal-00855043
https://hal.archives-ouvertes.fr/hal-00855043
DOI : 10.1016/j.epsl.2013.03.052

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We study diffusion in a heterogeneous medium that is characterized by spatially varying diffusion properties from a random walk point of view. We show that an inhomogeneous continuous time random walk (CTRW) with a spatially variable exponential transition time distribution solves the spatially discretized heterogeneous diffusion equation. This demonstrates the equivalence of the widely used time-domain random walk (TDRW) scheme and spatially inhomogeneous CTRW and at the same time provides a demonstration of the formal equivalence of the TDRW particle formulation and the heterogeneous diffusion equation. Based on this equivalence, we develop a TDRW method for heterogeneous diffusion under spatially variable multirate mass transfer properties. We discuss the implementation of these schemes and study the diffusion behavior in the presence of traps that are characterized by a truncated power-law trapping time distribution.
ISSN: 0309-1708

hal-00767566
https://hal.archives-ouvertes.fr/hal-00767566
DOI : 10.1016/j.advwatres.2012.07.015

Éditeur(s) : HAL CCSD IOS Press
Résumé : International audience
Because of the metabolic changes induced by a physical activity, the hemorheological properties of patients with sickle cell anemia could be further impaired and increase the risks for vaso-occlusive complications. However, few studies suggest that moderate physical activity could be beneficial rather than harmful in patients with sickle cell anemia (SCA). However, the definition of what can be considered as a moderate physical activity in SCA patients is imprecise. The present study tested the effects of a short incremental cycling exercise test conducted until the first ventilatory threshold on different biomarkers. Hematological and hemorheological parameters were compared between 8 patients with SCA and 13 healthy subjects (CONT) before, immediately after the end of the exercise and at 12, 36 and 60 hours after the exercise. We observed no significant hematological or hemorheological alteration induced by the exercise in the two groups. However, the exercise resulted in a delayed improvement of the red blood cell disaggregation threshold at 36 and 60 hrs after exercise in the SCA group which was paralleled to the decrease in the platelet count in this group. The present study suggests that such an exercise might be beneficial for microcirculatory blood flow.
ISSN: 1386-0291

hal-01137567
https://hal.univ-antilles.fr/hal-01137567

Éditeur(s) : HAL CCSD European Geosciences Union
Résumé : Xylem density is a physical property of wood that varies between individuals, species and environments. It reflects the physiological strategies of trees that lead to growth, survival and reproduction. Measurements of branch xylem density, ρx, were made for 1653 trees representing 598 species, sampled from 87 sites across the Amazon basin. Measured values ranged from 218 kg m−3 for a Cordia sagotii (Boraginaceae) from Mountagne de Tortue, French Guiana to 1130 kg m−3 for an Aiouea sp. (Lauraceae) from Caxiuana, Central Pará, Brazil. Analysis of variance showed significant differences in average ρx across regions and sampled plots as well as significant differences between families, genera and species. A partitioning of the total variance in the dataset showed that species identity (family, genera and species) accounted for 33% with environment (geographic location and plot) accounting for an additional 26%; the remaining "residual" variance accounted for 41% of the total variance. Variations in plot means, were, however, not only accountable by differences in species composition because xylem density of the most widely distributed species in our dataset varied systematically from plot to plot. Thus, as well as having a genetic component, branch xylem density is a plastic trait that, for any given species, varies according to where the tree is growing in a predictable manner. Within the analysed taxa, exceptions to this general rule seem to be pioneer species belonging for example to the Urticaceae whose branch xylem density is more constrained than most species sampled in this study. These patterns of variation of branch xylem density across Amazonia suggest a large functional diversity amongst Amazonian trees which is not well understood.
ISSN: 1726-4170

hal-01032137
https://hal.archives-ouvertes.fr/hal-01032137

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
3D seismic data located in the Gjallar Ridge (Vøring Basin, offshore Norway) reveals a closely-spaced polygonal fault system affecting more than 800 m of homogeneous mud-dominated Quaternary and Tertiary sequences. As some faults reach the modern seafloor, they represent an active polygonal fault system at present day. Even if the processes remain unclear and are still under debate, it is generally agreed that the initiation of polygonal faults is the result of shallow burial dewatering of fine-grained unconsolidated sediments by volumetric compaction. 3D seismic data are commonly interpreted by propagating horizons automatically and by picking faults manually. However, in the case of polygonal fault intervals, this approach is time consuming due to the huge number of faults and because automatic propagation can be misleading. In this study, we applied a new technique of 3D seismic interpretation based on a sequential stratigraphy analysis, using the new PaleoScan© software (Eliis Company). It allowed us to build a 3D geological model computing more than 300 horizons within the faulted intervals. We then used the coherency attribute, depicting anomalies in the shape of seismic waveform like faults, in order to constrain a possible link between fault distribution and stratigraphic levels. Our approach allows fault throws to be calculated in milliseconds on any polygonal fault plane. The result shows that fault segments have been reactivated by dip-linkage. Distribution of faults depends on mechanical units, intervals characterized by different petrophysical properties, which are independent from lithological and diagenetic changes. According to these results, we propose a model showing the evolution of polygonal fault intervals in which faulting stages are separated by a quiescence phase during burial. A first tier of polygonal faults is initiated at a specific depth, according to the Cam-clay model. Then, following a period of quiescence during which mud-rich sediments continued to accumulate, new fault segments are initiated above the first mechanical unit and within this undeformed interval. New nucleated faults then connect downward to pre-existing underlying polygonal fault system, thus progressively increasing the thickness of the faulted interval.
ISSN: 0025-3227

hal-00772470
https://hal.archives-ouvertes.fr/hal-00772470
DOI : 10.1016/j.margeo.2012.07.016

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
We use 3 yr of surface absolute gravity measurements at three sites on the Larzac plateau (France) to quantify the changes induced by topography and the building on gravity time-series, with respect to an idealized infinite slab approximation. Indeed, local topography and buildings housing ground-based gravity measurement have an effect on the distribution of water storage changes, therefore affecting the associated gravity signal. We first calculate the effects of surrounding topography and building dimensions on the gravity attraction for a uniform layer of water. We show that a gravimetric interpretation of water storage change using an infinite slab, the so-called Bouguer approximation, is generally not suitable. We propose to split the time varying gravity signal in two parts (1) a surface component including topographic and building effects (2) a deep component associated to underground water transfer. A reservoir modelling scheme is herein presented to remove the local site effects and to invert for the effective hydrological properties of the unsaturated zone. We show that effective time constants associated to water transfer vary greatly from site to site. We propose that our modelling scheme can be used to correct for the local site effects on gravity at any site presenting a departure from a flat topography. Depending on sites, the corrected signal can exceed measured values by 5-15 μGal, corresponding to 120-380 mm of water using the Bouguer slab formula. Our approach only requires the knowledge of daily precipitation corrected for evapotranspiration. Therefore, it can be a useful tool to correct any kind of gravimetric time-series data.
ISSN: 0956-540X

hal-00795590
https://hal.archives-ouvertes.fr/hal-00795590
DOI : 10.1093/gji/ggs007

Résumé : Les stocks des éléments dans les sols, et en particulier ceux du carbone, sont en constante évolution sous l’effet de facteurs naturels (climat, végétation, teneurs en argiles, etc.) et anthropiques (usages des sols, etc.). Notre objectif est donc, (i) de mieux comprendre les relations entre type de sol, système de culture et quantité de carbone stockée, (ii) d’étudier les conséquences des changements d’usage et de gestion des terres sur les formes de matière organique dans les sols et (iii) de préciser le rôle de la matière organique sur les propriétés physiques des sols.Des situations agro-pédologiques représentatives des trois grands modèles minéralogiques des sols tropicaux (Sols à allophanes (argiles non cristallisées), Sols à argiles 1/1 et Sols à argiles 2/1) et présentant des systèmes culturaux de différents niveaux d’intensification (monocultures intensives destinées à l’exportation, systèmes paysans faiblement intensifiés, etc.) ont ainsi été sélectionnées sur les sols de Martinique. Par ailleurs, afin de limiter les effets des usages antérieurs des parcelles, nous avons généralement choisi des situations culturales âgées au minimum de 3 ans.L’analyse des stocks de carbone des différentes parcelles fait apparaître des comportements différents : dans les sols à allophanes, il y a un effet de la minéralogie sur la stabilisation des matières organiques ; dans les sols à argiles cristallisées, il existe une corrélation entre la teneur en carbone (ou le stock organique) et la texture (ou teneur en éléments fins), aussi bien pour les situations non cultivées que pour les situations sous cultures. L’amplitude des variations (diminution) des stocks en carbone observées sous l’effet de différents modes de gestion des sols, dépend elle aussi de la texture : dans les sols sableux, la potentialité de séquestration du carbone est faible ou nulle, en revanche, les potentialités de stockage du carbone sont plus fortes dans les sols argileux.L’estimation des stocks totaux de carbone à l’échelle de la Martinique, pour un mètre de profondeur et pour une situation moyenne entre les cartes d’usage des terres de 1969/1970 et 1979/1980, s’élèvent à 11,859 Mt de C calculés pour 95,8% de la surface.La distribution de la matière organique du sol varie avec la texture du sol : dans les sols sableux, à faibles teneurs en matière organique, les matières organiques sont principalement associées aux fractions sableuses ; dans les sols argileux, plus riches en matières organiques, 50 à 60 % de la matière organique sont associées à la fraction argileuse. De même, la dynamique de la matière organique dépend également de la texture du sol : dans les sols sableux, les variations des stocks organiques sont essentiellement dues à la perte ou à l’accumulation en carbone de la fraction sableuse ; dans les sols argileux, la fraction argileuse participe de manière prépondérante aux variations des stocks organiques de ces sols lors de leur mise en culture ou en prairie ; les sols sablo-argileux ont un comportement intermédiaire entre ces deux pôles.La stabilité structurale varie avec la minéralogie. Les andosols (ou ALL) présentent un haut degré d’agrégation et de stabilité, du à la présence d’allophanes et à leur association particulière avec les composés organiques. Dans les sols à argiles cristallisées, la stabilité de l’agrégation est plus élevée dans les sols à argiles 1/1 (ou LAC) ; les valeurs les plus faibles sont généralement observées dans les parcelles sur sols à argiles 2/1 (ou HAC). En outre, la mise en culture se traduit généralement par une diminution de la stabilité de l’agrégation.L’intensification des cultures (labours fréquents, faibles restitutions de matière organique au sol, etc.) accentue la perte de la stabilité de l’agrégation provoquée par la mise en culture, en particulier dans les parcelles sur sols à argiles 2/1 (ou HAC).
Soils elements stocks, and particularly those of carbon, are in constant evolution under natural factors effect (climate, vegetation, clays content, etc) and anthropic factors effect (soils uses, etc). Our objective is thus, (i) to better understand the relations between soil, farming system and stored carbon quantity, (ii) to study the consequences of soils uses changes and of soils managements changes on organic matter shapes in soil and (iii) to specify organic matter role on soil properties physics.Representative agri-pedological situations of the three great mineralogical models of tropical soils (allophonic soils (not crystallized clays), 1:1 clay soils and 2:1 clay soils) and presenting agricultural systems of various levels of intensification (intensive monocultures intended for export, slightly intensified farming systems, etc) were thus selected in the soils of Martinique. In addition, to limit the effects of their former uses, we generally chose to the minimum 3 years old farming situations.The analysis of the various lands carbon stocks reveals different behaviors: in allophonic soils, a correlation exists between carbon content (or organic stock) and texture (or fine elements content), as well for not cultivated as for cultivated situations. Variations ranges (reduction) of carbon stocks observed under various management soils systems effect, also depends on texture: in sandy soils, carbon sequestration potentiality is low or null, on the other hand, carbon storage potentialities are higher in clay soils.The estimation of total carbon stocks on the scale of Martinique, for one meter of depth and for and average situation between the use soils charts of 1969/70 and 1979/80, rises to 11,859 Mt of C calculated for 95,8% of the surface.Soil organic matter distribution varies with soil texture: in sandy soils, with low contents of organic matter, organics matters are mainly associated with the sandy fractions; in clay soils, richer in organic matters, 50 to 60% of the organic matters are associated with the argillaceous fraction. In the same way, the organic matter dynamics also depends on soil texture: in sandy soils, organic stocks variations are primarily due to carbon loss or accumulation of the sandy fraction; in clay soils, the argillaceous fraction takes part in a dominating way in organic stocks variations of these soils at the time of their setting in culture or meadow; the sand-clay soils have an intermediate behavior between these two poles.Structural stability varies with mineralogy. Andosols (or ALL) present a high degree of aggregation and stability, due to the presence of allophones and their particular association with the organics compounds. In crystallized clay soils, aggregation stability is higher in 1:1 clay soils (or LAC); the lowest values are generally observed in the lands on 2:1 clay soils (or HAC). Moreover, culture setting generally results in aggregation stability reduction.Cultures intensification (frequent ploughings, low organic matter restitutions to the soil, etc) accentuates aggregation stability loss caused by culture setting, particularly in lands on 2:1 clay soils (or HAC).

http://www.theses.fr/2012AGUY0513/document

Éditeur(s) : HAL CCSD
Résumé : soutenue le 09 juin 2008
Intrinsic tribological properties of lamellar compounds are usually attributed to the presence of van der Waals gap in their structure. The controled variation of the graphite's crystal and electronic structure by intercalation processes of different species (electrophile, nucleophile ...) give a possibility to study in a more deeply way the friction reduction processes for low dimensional compounds. Three groups of intercalant are studied and tribological properties are correlated to structural and chemical evolutions.
Les propriétés tribologiques intrinsèques des composés lamellaires sont généralement attribuées à la présence de gap de van der Waals dans leur structure. La possibilité de faire varier de manière contrôlée la structure cristalline et la structure électronique du graphite par processus d'intercalation de différentes espèces chimiques (électrophile, nucléophile ...) sont utilisées pour étudier de façon plus approfondie les processus de réduction du frottement par les composés de basse dimensionnalité. Trois familles d'intercalants sont étudiées et les propriétés tribologiques sont corrélées aux évolutions structurales et chimiques.
https://tel.archives-ouvertes.fr/tel-00431713

Droits : info:eu-repo/semantics/OpenAccess
tel-00431713
https://tel.archives-ouvertes.fr/tel-00431713
https://tel.archives-ouvertes.fr/tel-00431713/document
https://tel.archives-ouvertes.fr/tel-00431713/file/These-DELBE_Karl.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Energy dissipation is observed on seismic data when a wave propagates through a porous medium, involving different frequency regimes depending on the nature of rock and fluid types. We focus here on the role of partial fluid saturation in unconsolidated porous media, looking in particular at P-wave phase velocity and attenuation. The study consists in running an experiment in a sand-filled tank partially saturated with water. Seismic propagation in the tank is generated in the kHz range by hitting a steel ball on a granite plate. Seismic data are recorded by buried accelerometers and injecting or extracting water controls the partial saturation. Several imbibition/drainage cycles were performed between the water and gas residual saturations. A Continuous Wavelet Transform applied on seismic records allowed us to extract the direct P-wave at each receiver.We observe an hysteresis in phase velocities and inverse quality factors between imbibition and drainage. Phase velocities and inverse quality factors are then jointly inverted to get a final poro-visco-elastic model of the partially saturated sand that satisfactorily reproduces the data. The model formulation consists in generalizing the Biot theory to effective properties of the fluid and medium (permeability and bulk modulus) in order to properly explain the phase velocity variation as a function of the saturation. The strong level of attenuation measured experimentally is further explained by an anelastic effect due to grain to grain sliding, adding to Biot's losses. This study shows that fluid distribution at microscopic scale has strong influence on the attenuation of direct P-waves at macroscopic scale and confirms that seismic prospection may be a powerful tool for the characterization of transport phenomena in porous media.
ISSN: 0956-540X

hal-00779920
https://hal.archives-ouvertes.fr/hal-00779920
https://hal.archives-ouvertes.fr/hal-00779920/document
https://hal.archives-ouvertes.fr/hal-00779920/file/Barriere_et_al_HAL.pdf
DOI : 10.1111/j.1365-246X.2012.05691.x

Éditeur(s) : HAL CCSD
Résumé : Different applications of linear elasticity in structural geology are presented in this thesis through the development of three types of numerical computer codes. The first one uses forward modeling to study displacement and perturbed stress fields around complexly faulted regions. We show that incorporating inequality constraints, such as static Coulomb friction, enables one to explain the angle of initiation of jogs in extensional relays. Adding heterogeneous material properties and optimizations, such as parallelization on multicore architectures and complexity reduction, admits more complex models. The second type deals with inverse modeling, also called parameter estimation. Linear slip inversion on faults with complex geometry, as well as paleo-stress inversion using a geomechanical approach, are developed. The last type of numerical computer code is dedicated to restoration of complexly folded and faulted structures. It is shown that this technique enables one to check balanced cross-sections, and also to retrieve fault chronology. Finally, we show that this code allows one to smooth noisy 3D interpreted faulted and folded horizons using geomechanics.
Différentes applications de l'élasticité linéaire en géologie structurale sont présentées dans cette thèse à travers le développement de trois types de codes numériques. Le premier utilise la modélisation directe pour étudier les déplacements et champs de contraintes autour de zones faillées complexes. On montre que l'ajout de contraintes inégalitaires, telles que la friction de Coulomb, permet d'expliquer l'angle d'initiation des dominos dans les relais extensifs. L'ajout de matériaux hétérogènes et d'optimisations, telles la parallélisation sur processeurs multi-coeurs ainsi que la réduction de complexité des modèles, permettent l'étude de modèles beaucoup plus complexes. Le second type de code numérique utilise la modélisation inverse, aussi appelée estimation de paramètres. L'inversion linéaire de déplacements sur les failles ainsi que la détermination de paléo-contraintes utilisant une approche géomécanique sont développées. Le dernier type de code numérique concerne la restauration de structures complexes plissées et faillées. Il est notamment montré qu'une telle méthode permet de vérifier l'équilibre de coupes géologiques, ainsi que de retrouver la chronologie des failles. Finalement, nous montrons que ce même code permet de lisser des horizons 3D faillés, plissés et bruités en utilisant la géomécanique.
https://tel.archives-ouvertes.fr/tel-00537899

tel-00537899
https://tel.archives-ouvertes.fr/tel-00537899
https://tel.archives-ouvertes.fr/tel-00537899/document
https://tel.archives-ouvertes.fr/tel-00537899/file/thesemaerten.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Anisotropy of low-field magnetic susceptibility (AMS) of basaltic lava flows can give some clues about post-emplacement tilting occurring in volcanic sequences. Such a study has been carried out on a sequence of 19 successive lava flows from Kerguelen Archipelago. Surprisingly, two different patterns were observed. The first one - herein called normal fabric - is consistent with the lava-flow direction inferred from geological observations, whereas the second one observed for about 70 per cent of the analysed samples - herein called abnormal fabric - appears to be unrelated to the shear history of the lava flows during their emplacements. These abnormal fabrics are not strictly inverse fabric but seem to have a more complex origin. The unusual nature of these abnormal fabrics has been confirmed by lattice preferred orientation of plagioclases obtained from high-resolution electron backscattered diffraction measurements. The aim of this study is to propose a physical interpretation of these fabrics. A first step in our understanding was to clearly identify the nature and the magnetic properties of the Fe-Ti oxides assemblage. Thus, we present a comprehensive rock magnetic analysis relying on low- and high-temperature thermomagnetic curves (K-T), crossover diagrams, first-order reversal curves, ore-microscopy, Mössbauer measurements and electron backscattered images. We found that in the present case the abnormal fabrics are probably linked to a mixture of prevailing single domain (SD) strongly interacting grains population and a subsidiary multidomain grains population. SD grains are identified as small magnetite crystallized within the interstitial glass in globular aggregates along the silicate framework. Then a question arises: to what extent such SD interacting grains in globular aggregates can affect the magnetic susceptibility and its anisotropy? To answer this question, we developed a physical model in which the total energy density of an SD grain with an uniaxial anisotropy is minimized. In this model, the distribution function of the direction of the magnetic interaction field is comprised between two boundary states. It is either isotropic, which formally corresponds to the thermal demagnetized state, or it is ordered, which formally corresponds to the Alternative Field demagnetized state. We show that in both cases the degree of anisotropy decreases as the interaction field increases. Thus, we conclude that the abnormal fabric encountered in this study can be simply explained by strong magnetostatic interactions that would explain the large scattering of AMS often observed in basaltic lava flows.
ISSN: 0956-540X

hal-00716449
https://hal.archives-ouvertes.fr/hal-00716449
https://hal.archives-ouvertes.fr/hal-00716449/document
https://hal.archives-ouvertes.fr/hal-00716449/file/gji-S-12-HAL.pdf
DOI : 10.1111/J.1365-246X.2012.05421.X

Éditeur(s) : HAL CCSD
Résumé : International audience
Characterizing the hydraulic properties of heterogeneous and complex aquifers often requires field scale investigations at multiple space and time scales to better constrain hydraulic property estimates. Here, we present and discuss results from the site of Ploemeur (Brittany, France) where complementary hydrological and geophysical approaches have been combined to characterize the hydrogeological functioning of this highly fractured crystalline rock aquifer. In particular, we show how cross-borehole flowmeter tests, pumping tests and frequency domain analysis of groundwater levels allow quantifying the hydraulic properties of the aquifer at different scales. In complement, we used groundwater temperature as an excellent tracer for characterizing groundwater flow. At the site scale, measurements of ground surface deformation through long-base tiltmeters provide robust estimates of aquifer storage and allow identifying the active structures where groundwater pressure changes occur, including those acting during recharge process. Finally, a numerical model of the site that combines hydraulic data and groundwater ages confirms the geometry of this complex aquifer and the consistency of the different datasets. The Ploemeur site, which has been used for water supply at a rate of about 106 m3 per year since 1991, belongs to the French network of hydrogeological sites H+ and is currently used for monitoring groundwater changes and testing innovative field methods.
AGU Fall Meeting 2014
San Francisco, United States

insu-01088596
https://hal-insu.archives-ouvertes.fr/insu-01088596

Éditeur(s) : HAL CCSD American Physical Society
Résumé : International audience
This is the second of two papers investigating the mechanical response of cemented granular materials by means of contact dynamics simulations. In this paper, a two-dimensional polydisperse sample with high void ratio is sheared in a load-controlled simple shear numerical device until the stress state of the sample reaches the yield stress. We first study the stress transmission properties of the granular material in terms of the fabric of different subsets of contacts characterized by the magnitude of their normal forces. This analysis highlights the existence of a peculiar force carrying structure in the cemented material, which is reminiscent of the bimodal stress transmission reported for cohesionless granular media. Then, the evolution of contact forces and torques is investigated trying to identify the micromechanical conditions that trigger macroscopic yielding. It is shown that global failure can be associated to the apparition of a group of particles whose contacts fulfill at least one of the local rupture conditions. In particular, these particles form a large region that percolates through the sample at the moment of failure, evidencing the relationship between macroscopic yielding and the emergence of large-scale correlations in the system.
ISSN: 1539-3755

hal-00523451
https://hal.archives-ouvertes.fr/hal-00523451
DOI : 10.1103/PhysRevE.82.011304

Éditeur(s) : HAL CCSD
Résumé : Among erosion processes, river incision is classicaly described as a key process controlling erosion of landscapes. Incision efficiency is mainly influenced by climate and erodibility. This latter is not only dependent on the nature of the bedrock, but also on its past deformation, which affects its rheological effective properties, such as fracture density. The main objectives of this thesis are: (1) to better constrain the relationship between effective properties and erodibility, and (2) to quantify the influence of erodibility and erosion on both the temporal and spatial building or decay of the topography. Several numerical tools are developed. A 1D formalism of landscape evolution is introduced, including river incision with stochastic distribution of water discharge and hillslope landsliding. A new remeshing algorithm called Surface Lagrangian Remeshing (SLR) is developed as a complement to remeshing algorithms dealing with internal elements. It allows one to take into account long-term erosion into 2D Lagrangian numerical codes based on triangular finite elements. Then the potentiality of measuring erodibility in-situ using a Schmidt hammer (R) is assessed for the active orogen of Taiwan, the diagenetic Annot sandstones and St Clement fault zone. Results suggest a strong control of R by effective properties. A linear model based on effective medium theory is applied to a fault zone with an unmacthed resolution (750 measures, 25 measures per square meter). The model successfully correlates R to fracture density. These results demonstrate that effective elasticity as well as erodibility are sensitive to the density and type of fractures. Finally I focus on the erosional and rheological conditions that allows reproducing post-orogenic evolution of mountain belts. A model coupling surface erosion and regional isostatic uplift is consistent with observations. The topographic decay and decrease of the ratio of surface elevation over crustal root thickness is at first order controlled by the initial geometry of the mountain belt and erosion efficiency. This new model highlights the control ofclimate and erodibility on the topographic decay and of lithospheric rheology on the perseverance of crustal roots.
Parmi les processus d'érosion, l'incision des rivières est classiquement décrit comme un processus clé contrôlant l'érosion des paysages. L'efficacité de l'incision est principalement influencée par le climat et par l'érodabilité. Ce dernier paramètre ne dépend pas seulement de la nature du substratum rocheux, mais aussi de sa déformation passée qui affecte ses propriétés rhéologiques équivalentes. Les principaux objectifs de cette thèse sont: (1) de mieux contraindre les relations entre propriétés équivalentes et érodabilité, et (2) de quantifier l'influence de l'érosion et de l'érodabilité sur la formation ou la décadence, spatiale et temporelle, de la topographie. Plusieurs outils numériques sont développés. Un formalisme 1D d'évolution des paysages est proposé, prenant en compte simultanément l'incision des rivières avec une distribution stochastique des débits en eau et l'érosion des versants par glissements de terrain. Un nouvel algorithme de remaillage appelé Surface Lagrangian Remeshing (SLR) est développé. Il permet de prendre en compte l'érosion à long terme dans les codes numériques 2D Lagrangiens basés sur des éléments finis triangulaires. Ensuite, la possibilité de mesurer in-situ l'érodabilité avec un marteau de Schmidt (R) est évaluée pour: l'orogène actif de Taiwan, les grès diagénétiques d'Annot et la zone de faille de St Clément. Les résultats suggèrent un fort contrôle de R par les propriétés équivalentes des roches testées. Un modèle linéaire, basé sur la théorie des milieux équivalents, est appliqué à une zone de faille avec une résolution inégalée (750 mesures, 25 mesures par mètre carré). Le modèle permet de corréler avec succès la densité de fracture et R. Ces résultats démontrent empiriquement que l'élasticité équivalente ainsi que l'érodabilité sont sensibles à la densité et à la nature des fractures. Enfin j'étudie les conditions d'érosion et de rhéologie qui permettent de reproduire l'évolution des chaînes de montagnes post-orogéniques. Un modèle couplant érosion en surface et soulèvement isostatique régional est compatible avec les observations. Les taux de décroissance topographique et de diminution du rapport de l'élévation de surface sur l'épaisseur de racine crustale sont contrôlés au premier ordre par la géométrie initiale de la chaîne de montagne et par l'efficacité de l'érosion. Ce nouveau modèle met en évidence le contrôle du climat et de l'érodabilité sur la décroissance topographique et de la rhéologie lithosphérique sur la persévérance des racines crustales.
https://tel.archives-ouvertes.fr/tel-00602341

tel-00602341
https://tel.archives-ouvertes.fr/tel-00602341
https://tel.archives-ouvertes.fr/tel-00602341/document
https://tel.archives-ouvertes.fr/tel-00602341/file/thesephilippesteer.pdf

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Studies on tree biomechanical design usually focus on stem stiffness, resistance to breakage or uprooting, and elastic stability. Here we consider another biomechanical constraint related to the interaction between growth and gravity. Because stems are slender structures and are never perfectly symmetric, the increase in tree mass always causes bending movements. Given the current mechanical design of trees, integration of these movements over time would ultimately lead to a weeping habit unless some gravitropic correction occurs. This correction is achieved by asymmetric internal forces induced during the maturation of new wood. The long-term stability of a growing stem therefore depends on how the gravitropic correction that is generated by diameter growth balances the disturbance due to increasing self weight. General mechanical formulations based on beam theory are proposed to model these phenomena. The rates of disturbance and correction associated with a growth increment are deduced and expressed as a function of elementary traits of stem morphology, cross-section anatomy and wood properties. Evaluation of these traits using previously published data shows that the balance between the correction and the disturbance strongly depends on the efficiency of the gravitropic correction, which depends on the asymmetry of wood maturation strain, eccentric growth, and gradients in wood stiffness. By combining disturbance and correction rates, the gravitropic performance indicates the dynamics of stem bending during growth. It depends on stem biomechanical traits and dimensions. By analyzing dimensional effects, we show that the necessity for gravitropic correction might constrain stem allometric growth in the long-term. This constraint is compared to the requirement for elastic stability, showing that gravitropic performance limits the increase in height of tilted stem and branches. The performance of this function may thus limit the slenderness and lean of stems, and therefore the ability of the tree to capture light in a heterogeneous environment.
ISSN: 0022-5193

hal-00534316
https://hal.archives-ouvertes.fr/hal-00534316
DOI : 10.1016/j.jtbi.2008.10.011

Éditeur(s) : HAL CCSD Geological society of London
Résumé : International audience
We present a synthesis of the tectonic and thermochronological evolution of the Eastern Tibet since the Triassic. The long-term cooling histories obtained on magmatic and metamorphic rocks of the South Songpan-Garze--, Kunlun and Yidun blocks are similar showing a very slow and regular cooling during Late Jurassic and Cretaceous, confirming the suspected lack of major tectonic events between c. 150 and 30 Ma. The exhumation linked to the Tertiary growth of the Tibetan Plateau initiated around 30 Ma and concentrates at the vicinity of the major tectonic structures. Exhumation rates increased again from about 7 Ma in the Longmen Shan. To interpret this very slow cooling rate between Late Jurassic and Early Cenozoic from granites of this area, we use a simple 1D thermal model that takes into account the thermal properties of both sediments and crust. The results suggest that: (1) high temperature (500 8C) can be kept over a long period of time; (2) during Cretaceous, cooling is mostly controlled by the thermal properties of sediments of continental origin; and (3) the initial Late Triassic rapid cooling rate was caused by the large thermal contrast between the granite body and the sedimentary rocks rather than by a high exhumation rate.
Growth and Collapse of the Tibetan Plateau

insu-00610491
https://hal-insu.archives-ouvertes.fr/insu-00610491
DOI : 10.1144/SP353.2