Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
Advances in groundwater storage monitoring are crucial for water resource management and hydrological processes understanding. The evaluation of water storage changes (WSC) often involve point measurements (observation wells, moisture probes, etc.), which may be inappropriate in heterogeneous media. Over the past few years, there has been an increasing interest in the use of gravimetry for hydrological studies. In the framework of the GHYRAF (Gravity and Hydrology inAfrica) project, 3 yr of repeated absolute gravity measurements using a FG5-type gravimeter have been undertaken at Nalohou, a Sudanian site in northern Benin. Hydrological data are collected within the long-term observing system AMMA-Catch. Once corrected for solid earth tides, ocean loading, air pressure effects, polar motion contribution and non-local hydrology, seasonal gravity variations reach up to 11 μGal, equivalent to a WSC of 260-mm thick infinite layer of water. Absolute temporal gravity data are compared to WSC deduced from neutron probe and water-table variations through a direct modelling approach. First, we use neutronic measurements available for the whole vertical profile where WSC occur (the vadose zone and a shallow unconfined aquifer). The RMSD between observed and modelled gravity variations is 1.61 μGal, which falls within the error bars of the absolute gravity data. Second, to acknowledge for the spatial variability of aquifer properties, we use a 2-D model for specific yield (Sy) derived from resistivity mapping and Magnetic Resonance Soundings (MRS). The latter provides a water content (θMRS) known to be higher than the specific yield. Hence, we scaled the 2-D model of θMRS with a single factor (α). WSC are calculated from water-table monitoring in the aquifer layer and neutronic measurements in the vadose layer. The value of α is obtained with aMonte-Carlo sampling approach, minimizing the RMSD between modelled and observed gravity variations. This leads to α = Sy/θMRS = 0.63 ± 0.15, close to what is found in the literature on the basis of pumping tests experiments, with a RMSD value of 0.94 μGal. This hydrogeophysical experiment is a first step towards the use of time-lapse gravity data as an integrative tool to monitor interannual WSC even in complicated subsurface distribution.
ISSN: 0956-540X

hal-00821181
https://hal.archives-ouvertes.fr/hal-00821181
DOI : 10.1093/gji/ggt146

Éditeur(s) : HAL CCSD
Résumé : Karstic aquifers represent the most important fresh water reservoirs in many regions of the world like the Mediterranean Basin. However, because of complex processes of karstification, those aquifers are highly heterogeneous at all spatial scales and vulnerable to contamination. In this dissertation, we studied the potential of gravimetry and ambient seismic noise for hydrological modeling in karstic areas.The dolomitic area surrounding the “GEK” observatory in the Durzon catchment on the Larzac plateau, in France, is the preferred site for these studies. Inside the observatory, a superconducting gravimeter dedicated to hydrology has continuously measured gravity changes since 2011 with high precision, undertaken for the first time on a karst. From this gravity monitoring, we made conceptual hydrological models which laid the foundation of 1-D flow physical models. Indeed, gravimetry is an integrative hydro-geophysical method which allows 1) to consider the epikarst, locally heterogeneous as an equivalent tabular medium and 2) to define the types of transfer (fast & slow) occurring at the site. Especially, the lack of fast transfer through the GEK epikarst was precisely quantified for the first time at the field scale (~100m). Gravity-driven water mass balance with local meteorological data (evapotranspiration from a flux tower and precipitation) allowed setting the bottom outlet of the model to 1 mm.day-1. This flow has proved to be representative of the low-flow discharge at the only spring which represents all groundwater outflows from the catchment. This result supposes the homogeneity of the dolomitic epikarst almost at the basin scale. Model parameters were next calibrated using one year of ambient seismic noise monitored at two stations. Phase velocity changes obtained by cross-correlating the noise between 6 and 8 Hz were used as a ”timer” to follow the water infiltration between a depth of 30 and 60 meters. Thus, monitoring seismic velocity changes using ambient seismic noise demonstrates great potential for the study of deep and complex critical zones and could fill the instrumental gap currently existing in hydrology.Time-lapse gravity measurements with a spring-based portable gravimeter have also demonstrated the different behavior of two epikarsts and their variability at the scale of a few hundred meters. Monthly measurements around the observatory revealed the spatial homogeneity of this dolomitic epikarst: all the stations showed the same water storage changes. On the contrary, seasonal surface to depth gravity measurements along the underground passage of the Saint-Ferréol sinkhole, in limestone, have shown fast transfer and strong spatial variability of water storage. Lithology is then expected to play a part in the epikarst capacity to retain water. The precision needed to measure the weak hydrological induced signals during those surveys required robust methodology and an ambient temperature effect on measurements with spring-based gravimeter was observed in the field and quantified in the laboratory.
Les aquifères karstiques représentent des ressources en eau essentielles dans de nombreuses régions du monde comme le bassin Méditerranéen. Cependant, de par les processus complexes de karstification, ces aquifères sont hétérogènes à de nombreuses échelles et vulnérables. Dans cette thèse, nous étudions le potentiel de la gravimétrie et du bruit sismique ambiant pour la modélisation hydrologique en milieu karstique.Le site dolomitique de l’observatoire « GEK », sur le bassin du Durzon dans le Larzac, est le site d’étude privilégié de ces travaux. Dans l’observatoire, un gravimètre supraconducteur dédié à l’hydrologie mesure depuis 2011 les variations de gravité en continu et à une très haute précision, pour la première fois sur un karst. Des modèles hydrologiques conceptuels ont été réalisés à partir de cette surveillance gravimétrique et ont permis de poser les bases de modèles physiques d’écoulements 1-D. En effet la gravimétrie, intégratrice, permet 1) de considérer l’épikarst localement hétérogène comme un milieu tabulaire équivalent et 2) de définir les types de transfert à l’œuvre sur le site. En particulier, l’absence de transfert rapide dans l’épikarst a été quantifiée avec précision pour la première fois à l’échelle du terrain (~100m). A l’aide de données météorologiques locales, un bilan de masse précis a permis de définir le flux en limite inférieure du modèle à 1 mm.jour-1. Ce flux s’est montré représentatif du débit de basses-eaux de la source drainant l’ensemble du bassin. Ce résultat suppose une homogénéité de l’épikarst dolomitique quasiment à l’échelle du bassin. Les paramètres des modèles physiques ont ensuite pu être calibrés à l’aide d’un an d’intercorrélation du bruit sismique ambiant entre deux stations. Les variations de vitesses de phase obtenues entre 6 et 8Hz nous ont servi de « chronomètre » pour suivre l’infiltration entre 30 et 60m de profondeur. La surveillance passive des variations de vitesses sismiques par intercorrélation du bruit sismique ambiant montre ainsi un fort potentiel pour l’étude des zones critiques profondes et complexes à l’échelle du terrain et peut combler la lacune instrumentale qui existe actuellement en hydrologie.Des campagnes répétées de mesures avec un gravimètre portable à ressort ont également mis en évidence le fonctionnement différent de deux épikarsts et leur variabilité à l’échelle de la centaine de mètres. Des mesures mensuelles autour de l’observatoire ont mis en évidence l’homogénéité spatiale de cet épikarst dolomitique : toutes les stations ont les mêmes variations temporelles de stock d’eau. Au contraire, des mesures saisonnières en surface et en profondeur le long de la galerie souterraine calcaire de l’abîme de Saint-Ferréol ont montré une variabilité spatiale forte du stockage ainsi que du transfert rapide. La lithologie de l’épikarst est donc suspectée de jouer un rôle dans sa capacité de stockage. Lors de ces campagnes, la faiblesse du signal recherché a nécessité une méthodologie précautionneuse et un effet de température sur les mesures des gravimètres relatifs à ressort a été observé sur le terrain et quantifié en laboratoire.
https://tel.archives-ouvertes.fr/tel-01649606

NNT : 2016MONTT128
tel-01649606
https://tel.archives-ouvertes.fr/tel-01649606
https://tel.archives-ouvertes.fr/tel-01649606/document
https://tel.archives-ouvertes.fr/tel-01649606/file/2016_FORES_archivage.pdf

Éditeur(s) : Pergamon-elsevier Science Ltd
Résumé : The late Quaternary has experienced large glacial/interglacial climatic variations and related 10's to 100 meters high-amplitude sea level fluctuations at Milankovich frequencies from 10's to 100 kyr during which carbonate platform tops have been exposed and re-flooded in many occasions. This study focuses on the accumulation of calci-turbidites, the aragonite onset/sharp increase in fine sediments and their timing in deep basins adjacent to carbonate platforms. A particular emphasis is developed on the occurrence of the first gravity flow event and aragonite onset/sharp increase and their linkage to the initial re-flooding of the platform tops during deglaciations. Three basins adjacent to isolated platforms in the Bahamas, the Northern Nicaragua Rise, and the Gulf of Papua, were selected to represent pure carbonate versus mixed systems, in quiescent versus tectonically active settings, and various carbonate bank top morphologies, ranging from atoll to relatively deeply and narrowly flooded flat top banks. In spite of these differences, each record illustrates a clear relationship between the timing of platform top re-flooding and initiation of significant carbonate export by gravity flows and low-density plumes into the surrounding basins. The concept of "re-flooding window" is introduced to characterize the prolific period of time during which bank and atoll-tops are flooded enough to produce large export of bank-derived aragonite and of calci-turbidites in adjacent basins. According to our datasets, the main re-flooding windows have occurred mainly on the last part of the sea level rise at each glacial termination (T), those periods being marked by some of the highest rates of sea level rise. The analysis of a long-piston core from the earthquakes-prone Walton Basin (Northern Nicaragua Rise) demonstrates that sea level, not seismic activities, played a major role as trigger mechanism for the initiation of gravity flows since the last four glacial/interglacial transitions, and supports the existence of an extra glacial termination during the early portion of the transition from MIS 7.4 to MIS 7.3 (TIIIA). (C) 2010 Elsevier Ltd. All rights reserved.
Quaternary Science Reviews (0277-3791) (Pergamon-elsevier Science Ltd), 2010-08 , Vol. 29 , N. 17-18 , P. 2010-2026

Droits : 2010 Elsevier Ltd All rights reserved.
http://archimer.ifremer.fr/doc/00012/12298/9095.pdf
DOI:10.1016/j.quascirev.2010.04.016
http://archimer.ifremer.fr/doc/00012/12298/

Éditeur(s) : HAL CCSD Springer Verlag
Résumé : In this paper, we investigate the impact of ambient temperature changes on the gravity reading of spring-based relative gravimeters. Controlled heating experiments using two Scintrex CG5 gravimeters allowed us to determine a linear correlation (R2> 0.9) between ambient temperature and gravity variations. The relation is stable and constant for the two CG5 we used: −5 nm/s2/∘C. A linear relation is also seen between gravity and residual sensor temperature variations (R2> 0.75), but contrary to ambient temperature, this relation is neither constant over time nor similar between the two instruments. The linear correction of ambient temperature on the controlled heating time series reduced the standard deviation at least by a factor of 2, to less than 10 nm/s2. The laboratory results allowed for reprocessing the data gathered on a field survey that originally aimed to characterize local hydrological heterogeneities on a karstic area. The correction of two years of monthly CG5 measurements from ambient temperature variations halved the standard deviation (from 62 to 32 nm/s2) and led us to a better hydrological interpretation. Although the origin of this effect is uncertain, we suggest that an imperfect control of the sensor temperature may be involved, as well as a change of the properties of an electronic component.
ISSN: 0949-7714

hal-01526952
https://hal.archives-ouvertes.fr/hal-01526952
DOI : 10.1007/s00190-016-0961-2

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
We use 3 yr of surface absolute gravity measurements at three sites on the Larzac plateau (France) to quantify the changes induced by topography and the building on gravity time-series, with respect to an idealized infinite slab approximation. Indeed, local topography and buildings housing ground-based gravity measurement have an effect on the distribution of water storage changes, therefore affecting the associated gravity signal. We first calculate the effects of surrounding topography and building dimensions on the gravity attraction for a uniform layer of water. We show that a gravimetric interpretation of water storage change using an infinite slab, the so-called Bouguer approximation, is generally not suitable. We propose to split the time varying gravity signal in two parts (1) a surface component including topographic and building effects (2) a deep component associated to underground water transfer. A reservoir modelling scheme is herein presented to remove the local site effects and to invert for the effective hydrological properties of the unsaturated zone. We show that effective time constants associated to water transfer vary greatly from site to site. We propose that our modelling scheme can be used to correct for the local site effects on gravity at any site presenting a departure from a flat topography. Depending on sites, the corrected signal can exceed measured values by 5-15 μGal, corresponding to 120-380 mm of water using the Bouguer slab formula. Our approach only requires the knowledge of daily precipitation corrected for evapotranspiration. Therefore, it can be a useful tool to correct any kind of gravimetric time-series data.
ISSN: 0956-540X

hal-00795590
https://hal.archives-ouvertes.fr/hal-00795590
DOI : 10.1093/gji/ggs007

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
We analyse temporal variations of gravity measured in southern Taiwan since November 2006 at 10 sites using absolute gravimeters and, since November 2008, at 70 sites using a relative gravimeter. We describe and apply methods to interpret the gravity changes in terms of local hydrological processes and vertical ground motions. The effect of land water is computed from local rainfall data and a model of rain accumulation and discharge in the ground. The effect of the vertical motions of the ground is estimated using time-series of permanent Global Positioning System (GPS) stations and the theoretical gravity to height ratio of −2 μGal cm−1. Unexpectedly, Morakot typhoon (2009 August), the strongest typhoon in Taiwan in 50 yr, was responsible for the highest gravity changes. Morakot triggered numerous large landslides and debris flow deposits. Their thicknesses are estimated from the gravity changes (up to ∼280 μGal) along with field observations and satellite images.
ISSN: 0956-540X

hal-00768216
https://hal.archives-ouvertes.fr/hal-00768216
DOI : 10.1093/gji/ggs019

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : International audience
Time-lapse microgravity surveying combined with absolute gravity measurements is used to investigate water storage changes in a karst aquifer of similar to 100 km(2) area. The survey consists of 40 gravity stations measured with a relative gravimeter; absolute gravity is measured at three stations for each survey. In total, four gravity surveys are performed over a 2 year time period during consecutive wet and dry periods. Survey precisions range between 2.4 and 5 mu Gal, enabling statistically significant detection of 10 mu Gal change, i.e., similar to 0.25 m equivalent water level change. Observed gravity changes are coherent between consecutive survey periods, i.e., net water withdrawal and net water recharge is observed, reaching changes as high as 22 mu Gal. Observed gravity changes allow refining evapotranspiration estimates, which may serve to improve the water budget of the aquifer. High-and low-gravity amplitude zones characterize the karst system, demonstrating spatially variable storage behavior. Geomorphologic considerations are invoked to explain the location of preferential zones of water storage, and a conceptual model of water storage is discussed for the studied karst.
ISSN: 0148-0227

hal-00496400
https://hal.archives-ouvertes.fr/hal-00496400
DOI : 10.1029/2009JB006616

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
In this study we attempt to understand the water storage variations in a karst aquifer on the Larzac Plateau (South of France) using ground-based gravimetry. Surface to 60 m depth gravity measurements are performed three times a year since 2006 down a pothole, in complement to monthly absolute gravity (AG) measurements at three sites. The time variations of the surface to depth (STD) gravity differences are compared with the AG variations. Using a simple Bouguer plate model, we find that the STD gravity differences are very similar to the AG variations. The STD gravity differences are then used to determine apparent density values. These integrative density values are compared with measured grain densities from core samples to obtain an apparent porosity and saturation change representative of the investigated depth. The apparent porosity ranges from 4.8 to 7.3 per cent. We then discuss on the repartition of the apparent physical properties with respect to the epikarst and infiltration zone karst structures. We argue that AG and STD differences monitor epikarst water storage variations. Within this scope, we discuss the fact that seasonal scale water storage variation occurs predominantly in the epikarst.
ISSN: 0956-540X

hal-00413528
https://hal.archives-ouvertes.fr/hal-00413528
DOI : 10.1111/j.1365-246X.2009.04118.x

Éditeur(s) : HAL CCSD
Résumé : Karst systems are the most important groundwater reservoirs in Mediterranean areas. Their structure and functioning are complex and not well known because of the high heterogeneity created and organised by groundwater flow. Water storage entities and water storage changes within remain difficult to assess by direct measurement and modelling. Geodetic monitoring is here used to constrain and bring original insights on karst system functioning. The Durzon karst system (Larzac plateau, Southern France) is monitored by several geodetic techniques: - Monthly absolute gravity measurements at three sites - Time-lapse surface to depth gravity measurements - Time-lapse microgravity surveying - Continuous long base hydrostatic tiltmeter monitoring at two sites Absolute gravity monitoring complemented with relative gravity surveys allows quantification of water storage changes on the studied karst system. Interannual water storage changes as detected by gravity are ~400 mm in amplitude. These storage changes are shown to occur in the epikarst and infiltration zone in certain areas. Water storage variations spatial heterogeneity is also demonstrated on the karst system. Tilt measurements monitor fast and slow infiltration processes within the karst fractured media. Karst system geodetic monitoring brings both quantitative and integrated hydrologic knowledge. Such methods could be applied to other karst aquifer studies.
Les aquifères karstiques constituent l'essentiel des ressources en eau souterraine sur le pourtour de la Méditerranée. Leur structure et leur fonctionnement sont complexes et mal connus à cause du processus de karstification qui hiérarchise la circulation hydrodynamique en leur sein. La localisation du stockage de l'eau et de ses variations au sein de tels aquifères est difficile à mesurer et à modéliser. Nous utilisons les outils de la géodésie pour apporter de nouvelles contraintes sur le fonctionnement hydrologique et les variations de stock d'eau en milieu karstique. Ainsi, le système karstique du Durzon, (Causse du Larzac, France) fait l'objet d'un suivi par plusieurs méthodes géodésiques incluant: - Des mesures de gravimétrie absolue en trois sites répétées de manière mensuelle ; - Des mesures répétées de gravimétrie relative entre la surface et la profondeur du karst ; - Des mesures répétées de microgravimétrie ; - Des mesures inclinométriques longue base en deux sites. Nous démontrons que le couplage entre la gravimétrie absolue et relative permet d'appréhender les variations de stock d'eau sur le bassin d'alimentation étudié. Les variations inter-anuelles observées sont de l'ordre de 400 mm, et nous montrons que celles-ci s'opèrent dans certaines zones au sein des horizons supérieurs du karst : épikarst et zone d'infiltration. Une forte hétérogénéité spatiale des variations de stockage est aussi mise en évidence à l'échelle du bassin d'alimentation. Les mesures inclinométriques permettent de suivre les phénomènes d'infiltration rapide et lente dans la masse karstique fracturée. Le suivi géodésique de ce système karstique permet d'apprécier quantitativement et de façon intégrée son fonctionnement hydrologique et pourra être transposé pour l'étude d'autres aquifère karstiques.
https://tel.archives-ouvertes.fr/tel-00404851

tel-00404851
https://tel.archives-ouvertes.fr/tel-00404851
https://tel.archives-ouvertes.fr/tel-00404851/document
https://tel.archives-ouvertes.fr/tel-00404851/file/THESE_jacob.pdf

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : In this paper we present the potential of a new compact superconducting gravimeter (GWR iGrav) designed for groundwater monitoring. At first, 3 yr of continuous gravity data are evaluated and the performance of the instrument is investigated. With repeated absolute gravity measurements using a Micro-g Lacoste FG5, the calibration factor (−894.8 nm s−2 V−1) and the long-term drift of this instrument (45 nm s−2 yr−1) are estimated for the first time with a high precision and found to be respectively constant and linear for this particular iGrav. The low noise level performance is found similar to those of previous superconducting gravimeters and leads to gravity residuals coherent with local hydrology. The iGrav is located in a fully instrumented hydrogeophysical observatory on the Durzon karstic basin (Larzac plateau, south of France). Rain gauges and a flux tower (evapo-transpiration measurements) are used to evaluate the groundwater mass balance at the local scale. Water mass balance demonstrates that the karst is only capacitive: all the rainwater is temporarily stored in the matrix and fast transfers to the spring through fractures are insignificant in this area. Moreover, the upper part of the karst around the observatory appears to be representative of slow transfer of the whole catchment. Indeed, slow transfer estimated on the site fully supports the low-flow discharge at the only spring which represents all groundwater outflows from the catchment. In the last part of the paper, reservoir models are used to characterize the water transfer and storage processes. Particular highlights are done on the advantages of continuous gravity data (compared to repeated campaigns) and on the importance of local accurate meteorological data to limit misinterpretation of the gravity observations. The results are complementary with previous studies at the basin scale and show a clear potential for continuous gravity time-series assimilation in hydrological simulations, even on heterogeneous karstic systems.
ISSN: 0956-540X

hal-01526965
https://hal.archives-ouvertes.fr/hal-01526965
https://hal.archives-ouvertes.fr/hal-01526965/document
https://hal.archives-ouvertes.fr/hal-01526965/file/fores2016.pdf
DOI : 10.1093/gji/ggw396

Éditeur(s) : HAL CCSD
Résumé : Joint inversions are now commonly used in Earth Sciences. They have been developed to better understand Earth structure since they provide more constraints on the inverted parameters. We propose a new process to simultaneously invert several data sets in order to better image 3-D crustal and upper mantle structures. Our inversion uses 3 kind of data which present a good complementarity : (1) P receiver functions to provide Moho depth variations, (2) teleseismic delay times of P waves to retrieve velocity anomalies in the crust and upper mantle, (3) gravity anomalies to image density variations at lithospheric scale. In our scheme, receiver functions are first inverted. The resulting Moho depths are then interpolated and incorporated as a priori information into the joint inversion of teleseismic delay times and gravity anomalies process. In our new approach, we perform a model space search for Moho variations, P-velocity and density structure to find acceptable fit to the three data sets. In order to preferentially sample the good data fit region, we chose the Neighborhood algorithm of Sambridge to optimistically survey the model space. We model the delay times with a 3-D raytracing using velocity nodes evenly spaced and linked with density nodes via a linear relationship. This relationship can evolve through depth, simulating its pressure dependance. We test our scheme on synthetic examples, and apply the method in a continental rifting region where deformation processes are complex and badly known. This joint inversion thus provides more constraints on the inverted parameters, and allows us to better image crust - mantle interactions in the case of the Hangai dome (Central Mongolia). Indeed, in this area, we expect an asthenospheric upwelling to dynamically support the topography, but we image a density - velocity anomaly in the lower crust. The effects on topography and the origin (composition vs. thermal) of this anomaly are still under debate.
Les inversions conjointes sont maintenant communément utilisées en Sciences de la Terre. Elles ont été développées afin d'améliorer notre connaissance et compréhension de la structure interne de la Terre puisqu'elles apportent de plus en plus de contraintes sur les paramètres inversés. Dans cette thèse, nous proposons un nouveau processus d'inversion conjointe qui prend en compte trois paramètres différents et qui mène à l'obtention d'un modèle lithosphérique tridimensionnel. Notre méthode utilise trois types de données gravimétriques et sismologiques qui présentent une bonne complémentarité : (1) Les fonctions récepteur P afin d'obtenir les variations de profondeur du Moho, (2) les délais de temps d'arrivées P des téléséismes pour retrouver les anomalies de vitesse dans la croûte et le manteau supérieur, (3) les anomalies gravimétriques qui donnent accès aux variations de densité à l'échelle lithosphérique. Dans le schéma d'inversion proposé, nous inversons d'abord les fonctions récepteur. Les variations de profondeur du Moho qui en résultent sont alors interpolées puis incorporées comme information a priori dans le processus d'inversion conjointe gravimétrie - tomographie télésismique. Que ce soit pour les fonctions récepteur ou pour la partie conjointe, notre méthode d'inversion se base sur un algorithme de recherche afin de trouver la structure qui minimise l'écart aux trois types de données. Nous avons opté pour l'algorithme de voisinage qui présente l'avantage de concentrer sa recherche dans les régions qui minimisent l'écart aux données sans toutefois abandonner les autres régions afin de limiter les risques de convergence vers un minimum local. Nous utilisons un modèle 3-D constitué de noeuds de vitesse afin de modéliser les délais de temps. Ces noeuds de vitesse sont liés aux noeuds de densité grâce à une relation linéaire entre vitesse et densité. Cette relation peut évoluer avec la profondeur de manière à simuler les effets dus aux variations de pression. Nous avons réalisé plusieurs tests synthétiques afin d'évaluer le comportement de notre nouvelle méthode. Ils ont permis de montrer que les variations du Moho ainsi que les anomalies de vitesse et densité sont bien retrouvées. Ils ont également montré l'importance de la prise en compte de ces trois types de données dans un même schéma d'inversion, notamment en ce qui concerne la faculté de discerner les variations d'interfaces des anomalies volumiques. Nous avons ensuite appliqué la méthode dans une région continentale en phase de rifting où les processus de déformation sont complexes et mal connus. Notre nouvelle méthode a apporté davantage de contraintes sur les paramètres inversés et a permis d'obtenir un modèle correctement résolu de la croûte et du manteau supérieur sous le dôme de Hangai (Mongolie Centrale). Une anomalie asthénosphérique sous le dôme est souvent invoquée pour expliquer sa topographie élevée mais c'est une anomalie (en vitesse et densité) crustale (croûte inférieure) qui s'exprime dans nos modèles. Ses effets sur la topographie et son origine (compositionnelle et/ou thermique) sont encore débattus et nécessiteraient des études plus poussées (paramétriques, VP =VS, ...).
https://tel.archives-ouvertes.fr/tel-00783524

tel-00783524
https://tel.archives-ouvertes.fr/tel-00783524
https://tel.archives-ouvertes.fr/tel-00783524/document
https://tel.archives-ouvertes.fr/tel-00783524/file/Basuyau2011.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
BackgroundTree above ground biomass (AGB) is currently estimated by tree-level allometrical models that take into account, tree volume estimated from proxy variables of tree size (DBH) and species average wood specific gravity (WSG). These methods are common and realistic from a practical point of view. However, they do not take into account deviance from fixed allometrical trajectories and species or tree level WSG variations. Here, we present Xtrawood software that allows computation of tree AGB according to structure and WSG variations.MethodXtrawood reconstructs tree structure and integrates WSG variations by merging tree structure and WSG data measured at different position in trees, leading to the computation of global AGB and visualization of WSG variation along tree structure. Tree structure is measured according to stem dimensions (length, diameter) and positions within tree, and encoded in Multiscale Tree Graph format (MTG). WSG data is made of radial WSG profiles (1 measure each 0,5 cm from pith to bark) sampled at different heights within whole tree. Xtrawood output are illustrated using a dataset collected on an Amazonian forest ‘biomass dominant species’, Dicorynia guianensis Amsh., also known to exhibit substantial WSG gradients along both radial and vertical axis. 9 trees ranging from 15 to 60 cm DBH were measured by climbers. Each tree was felled and samples were collected at different positions (3 in trunk, 1 to 5 in crown) to record WSG radial profiles.ResultsXtrawood allows computation of tree volume, but also visualization of WSG variations in tree as well as inference of WSG radial profiles at different heights. Output variables are decomposed according to different tree scale and locations (axis, trunk/crown) and easy to extract. Xtrawood results will be compared to those of standard estimation method and can be used to identify positions in trees where WSG value leads to the better estimate of tree AGB.Conclusion/perspectiveXtrawood produces AGB estimate with data from intensive measurements practices. The sampling protocol, used here, remains destructive and time-consuming because Xtrawood is not directly dedicated to forest managers, but to help calibration of realistic sampling strategies. Moreover, Xtrawood offers a way to understand relationships between tree development, WSG variations within tree structure and biomass accumulation in the context of natural forests or plantations. A software demo is available at coffee break.
53rd Annual Meeting of the Association for Tropical Biology and Conservation (ATBC 2016)
Montpellier, France

Droits : http://creativecommons.org/licenses/by/
hal-01349613
https://hal.archives-ouvertes.fr/hal-01349613

Éditeur(s) : HAL CCSD American Geophysical Union
Résumé : The acquisition of reliable data sets representative of hydrological regimes and their variations is a critical concern for water resource assessment. For the subsurface, traditional approaches based on probe measurements, core analysis, and well data can be laborious, expensive, and highly intrusive, while only yielding sparse data sets. For this study, an innovative field survey, merging relative microgravimetry, magnetic resonance soundings, and hydrological measurements, was conducted to evaluate both surface and subsurface water storage variations in a semiarid Sahelian area. The instrumental setup was implemented in the lower part of a typical hillslope feeding to a temporary pond. Weekly measurements were carried out using relative spring gravimeters during 3 months of the rainy season in 2009 over a 350 × 500 m2 network of 12 microgravity stations. Gravity variations of small to medium amplitude (≤220 nm s−2) were measured with accuracies better than 50 nm s−2, revealing significant variations of the water storage at small time (from 1 week up to 3 months) and space (from a couple of meters up to a few hundred meters) scales. Consistent spatial organization of the water storage variations were detected, suggesting high infiltration at the outlet of a small gully. The comparison with hydrological measurements and magnetic resonance soundings involved that most of the microgravity variations came from the heterogeneity in the vadose zone. The results highlight the potential of time lapse microgravity surveys for detecting intraseasonal water storage variations and providing rich space-time data sets for process investigation or hydrological model calibration/evaluation
ISSN: 0043-1397

hal-00857351
https://hal.archives-ouvertes.fr/hal-00857351
DOI : 10.1002/wrcr.20235

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Joint inversions are now commonly used in the earth sciences. They have been developed to better understand the structure of the earth, since they provide more constraints on the inverted parameters. We propose a new process to simultaneously invert several data sets in order to better image 3D crustal and upper mantle structures. Our inversion uses three kinds of data that present good complementarity: (1) P-wave receiver functions to provide Moho depth variations, (2) teleseismic delay times of P-waves to retrieve velocity anomalies in the crust and the upper mantle, and (3) gravity anomalies to image density variations at the lithospheric scale. We use a stochastic scheme, where receiver functions are first inverted. The interpolated resulting Moho depths are incorporated as a priori information into the joint inversion of teleseismic delay times and gravity anomalies process. Moreover, velocity and density can be linked by empirical relationships, which justifies the joint inversion of those parameters. In our stochastic approach, we perform a model space search for Moho variations, P-velocity, and density structure to find an acceptable fit to the three data sets. In order to preferentially sample the good data fit regions, we chose the neighborhood algorithm of Sambridge to optimistically survey the model space. We model the delay times with 3D raytracing using evenly spaced velocity-density nodes. We present here the first results given by this method on synthetic tests. (C) 2011 Elsevier Ltd. All rights reserved.
ISSN: 0098-3004

hal-00643158
https://hal.archives-ouvertes.fr/hal-00643158
DOI : 10.1016/j.cageo.2010.11.017

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
We investigate the contribution of atmospheric and its induced non-tidal oceanic loading effects on surface time-varying gravity and tilt measurements for several stations in Western Europe. The ocean response to pressure forcing can be modelled accordingly to the inverted barometer, i.e. assuming that air pressure variations are fully compensated by static sea height changes, or using ocean general circulation models.Wevalidate two runs of theHUGO-mbarotropic ocean model by comparing predicted sea surface height variations with hundred tide-gauge measurements along the European coasts. We then show that global surface pressure field, as well as a barotropic high-resolution ocean model forced by air pressure and winds allow in most cases a significant reduction of the variance of gravity residuals and, to a smaller extends tilt residuals. Wefinally show that precise gravity measurements with superconducting gravimeters allow the observation of large storm surges, occurring in the North Sea, even for inland stations. However, we also confirm that the continental hydrology contribution cannot be neglected. Thanks to their specific sensitivity feature, only tiltmeters closest to the coast can clearly detect the loading due to these storm surges.
ISSN: 0264-3707

hal-00708046
https://hal.archives-ouvertes.fr/hal-00708046
https://hal.archives-ouvertes.fr/hal-00708046/document
https://hal.archives-ouvertes.fr/hal-00708046/file/ETS2008_BOY.pdf
BIBCODE : 2009JGeo...48..182B

Résumé : Une étude de faisabilité de poutres en bois lamellé-collé a été menée en Guyane Française en utilisant les essences locales. Le but est de déterminer les paramètres de collage assurant la bonne résistance mécanique des assemblages par lamellation et par aboutage, nécessaires à la fabrication de poutres en bois lamellé-collé en climat tropical. Trois essences de bois abondantes de différentes densités ont été sélectionnées. Les adhésifs de types Mélamine-Urée-Formol et Résorcinol-Phénol-Formol ont été utilisées. Les paramètres de collage considérés sont : le grammage, le temps d’assemblage fermé et la pression.En utilisant les normes Européennes, plusieurs campagnes de tests ont été conduites sur des échantillons normalisés. Concernant le collage par lamellation, des tests élémentaires de délamination et de cisaillement des joints de colle ont été réalisés. Le test de délamination consiste en deux cycles d’immersion dans l’eau sous pression et de séchage, il induit de sévères variations d’humidité du bois susceptibles de créer des ouvertures des joints de colles. Le collage par aboutage est réalisé sur des poutres normalisées aboutées. Les entures sont obtenues grâce à un outillage standard communément utilisé pour les résineux. Les résultats ont mis en évidence l’influence des propriétés du bois et des paramètres de collage sur la résistance du joint et la résistance mécanique du produit. En effet, les paramètres du bois, tels que la densité, la rétractibilité et l’imprégnation, ont une forte influence sur le collage, en particulier sur la pression et le grammage nécessaires à la production d’un produit commercialisable. Il apparait qu’un bois de densité moyenne et poreux nécessite un grammage et une pression élevés comparé à un bois de densité élevée qui nécessite des valeurs moindres. Aussi, l’influence d’autres paramètres de fabrication, tels que le rabotage, l’encollage double face et simple face ainsi que l’épaisseur des lamelles, a été établie. Par contre il semblerait que le matériel communément utilisé pour l’aboutage des résineux n’est pas adapté aux feuillus tropicaux. En final, des paramètres de collage ont été validés pour la fabrication de lamellé-collé endémique en Guyane Française et une étude du coût de production d’une poutre lamellé-collé standard a identifié les conditions économiques d’une fabrication en Guyane Française.
A feasibility study of glued-laminated timber beams was carried out in French Guiana using local wood species. The aim of the study was to evaluate the gluing parameters that could ensure good mechanical properties for the manufactured glued-laminated beams in tropical climates. Three abundant wood species with different specific gravity were selected for the study. Melamine-Urea-Formaldehyde and Resorcinol-Phenol-Formaldehyde resins were used for gluing. The three gluing parameters considered are: adhesive spread rate, closing assembly time and gluing pressure.Using European standards, several laboratory tests were performed on normalized samples. The evaluation of a successful lamella’s gluing was done by using elementary tests of delamination and shearing. A delamination test consists of two cycles of water immersion at high pressure and drying which induces severe hygroscopic variation in wood thus causing joints opening. The finger-joints are made using a standard tool usually used for cutting softwoods. The performed tests revealed the influence of wood properties and the gluing parameters on the joint resistance and the mechanical properties of the product. Results show that wood properties such as specific gravity, shrinkage coefficient, and permeation, have a high degree of influence on the gluing step especially on the gluing pressure and on the adhesive spread rate needed to produce a commercial product. Furthermore, wood with medium specific gravity needs more adhesive and more pressure than the one with high specific gravity. Additionally, the effects of other manufacturing parameters, such as planning, double or simple side glue spreading and lamellae thicknesses, on the glue joint resistance were demonstrated. Finally, the common tools used for softwoods are not adapted to making the finger joints with tropical hardwoods.In conclusion, optimal gluing parameters for manufacturing glued-laminated timber beams in French Guiana were established and an economical study using standard glued-laminated timber beams revealed the economic conditions under which a successful manufacturing of these local beams can be implemented in French Guiana.

http://www.theses.fr/2011AGUY0484/document

Éditeur(s) : American Geophysical Union
Résumé : Two time series of deep ocean bottom pressure records (BPRs) in between the Crozet Islands and Kerguelen are compared with GRACE (Gravity Recovery And Climate Experiment) equivalent water heights. An analysis of the correlation is performed for four time series: 1) monthly averages of the equivalent water height at the Crozet Islands, 2) the same near the Kerguelen Islands, 3) the mean of the two preceding series and 4) the difference between the two locations expressed in terms of geostrophic transport. We find that smoothed GRACE solutions are strongly correlated with the BPR data with correlation coefficients in the order of 0.7-0.8. Consequently GRACE measures real oceanic mass variations in this region.
Geophysical Research Letters ( GRL ) (0094-8276) (American Geophysical Union), 2006-11 , Vol. 33 , N. 21 , P. NIL_10-NIL_13

Droits : 2006 AGU
http://archimer.ifremer.fr/doc/2006/publication-2088.pdf
DOI:10.1029/2006GL027452
http://archimer.ifremer.fr/doc/00000/2088/

Éditeur(s) : Elsevier Science Bv
Résumé : We present the results from a new grid of deep penetration multichannel seismic (MCS) profiles over the 280-km-long north-central segment of the Lesser Antilles subduction zone. The 14 dip-lines and 7 strike-lines image the topographical variations of (i) the subduction interplate décollement, (ii) the top of the arcward subducting Atlantic oceanic crust (TOC) under the huge accretionary wedge up to 7 km thick, and (iii) the trenchward dipping basement of the deeply buried forearc backstop of the Caribbean upper plate. The four northernmost long dip-lines of this new MCS grid reveal several-kilometres-high topographic variations of the TOC beneath the accretionary wedge offshore Guadeloupe and Antigua islands. They are located in the prolongation of those mapped on the Atlantic seafloor entering subduction, such as the Barracuda Ridge. This MCS grid also provides unexpected evidences on huge along-strike topographical variation of the backstop basement and of the deformation style affecting the outer forearc crust and sediments. Their mapping clearly indicates two principal areas of active deformation in the prolongation of the major Barracuda and Tiburon ridges and also other forearc basement highs that correspond to the prolongation of smaller oceanic basement highs recently mapped on the Atlantic seafloor. Although different in detail, the two main deforming forearc domains share similarities in style. The imaged deformation of the sedimentary stratification reveals a time- and space-dependent faulting by successive warping and unwarping, which deformation can be readily attributed to the forearc backstop sweeping over the two obliquely-oriented elongated and localized topographical ridges. The induced faulting producing vertical scarps in this transport does not require a regional arc-parallel extensional regime as proposed for the inner forearc domain, and may support a partitioned tectonic deformation such as in the case of an outer forearc sliver. A contrasted reflectivity of the sedimentary layering at the transition between the outer forearc and accretionary domains was resolved and used to define the seaward edge of the outer forearc basement interpreted as being possibly a proxy to the updip limit of the interplate seismogenic zone. Its mapping documents along-arc variations of some tens of kilometres the subduction backstop with respect to the negative gravity anomaly commonly taken as marking the subduction trench. With the exception of the southernmost part, the newly mapped updip limit reaches 25 km closer to the trench, thus indicating a possible wider seismogenic zone over almost the whole length of the study area.
Tectonophysics (0040-1951) (Elsevier Science Bv), 2013-09 , Vol. 603 , P. 32-54

Droits : 2013 Elsevier B.V. All rights reserved
http://archimer.ifremer.fr/doc/00139/25003/23109.pdf
DOI:10.1016/j.tecto.2013.05.028
http://archimer.ifremer.fr/doc/00139/25003/

Éditeur(s) : HAL CCSD De Gruyter
Résumé : International audience
This study aims at better understanding the respective influences of specific gravity (γ), microfibril angle (MFA), and cell-wall matrix polymers on viscoelastic vibrational properties of wood in axial direction. The wide variations of properties between normal wood (NW) and compression wood (CW) are in focus. Three young bent trees (Picea abies, Pinus sylvestris and Pinus pinaster) that recovered verticality were sampled. Several observed differences between NW and CW were highly significant in terms of anatomical, physical (γ, shrinkage, CIELab colorimetry), mechanical (compressive strength), and vibrational properties. Specific dynamic modulus of elasticity (E'/γ) decreases with increasing MFA, and Young's modulus (E') can be satisfactorily explained by γ and MFA. Apparently, the type of the cell wall polymer matrix is not influential in this regard. The damping coefficient (tanδ) does not depend solely on MFA of NW and CW. The tanδ - E'/γ relationship evidences that, at equivalent E'/γ, the tanδ of CW is approx. 34% lower than that of NW. This observation is ascribed to the more condensed nature of CW lignins, and this is discussed in the context of previous findings in other hygrothermal and time/frequency domains. It is proposed that the lignin structure and the amount and type of extractives, which are both different in various species, are partly responsible for taxonomy-related damping characteristics.
ISSN: 0018-3830

hal-00808062
https://hal.archives-ouvertes.fr/hal-00808062
https://hal.archives-ouvertes.fr/hal-00808062/document
https://hal.archives-ouvertes.fr/hal-00808062/file/Changes_viscoelastic_vibrational_Bremaud_al.pdf
DOI : 10.1515/hf-2011-0186

Éditeur(s) : HAL CCSD
Résumé : International audience
The « METYSS » cruise was carried out in June 2009 onboard the R/V « Téthys II » along the eastern Sardinian and south-eastern Corsican margins, western Tyrrhenian Sea, in order to better constrain the potential links between deformation related to either crustal tectonics or salt tectonics and sediment accumulation, especially during the Messinian and Plio-Quaternary times. We acquired 15 high-resolution seismic reflection profiles (about 1200 km in cumulative length) along the south-eastern Corsican margin, immediately north of the Bonifacio Strait and along the upper and middle parts of the eastern Sardinian margin, from the continental slope to the Cornaglia Terrace. The Tyrrhenian Sea is considered as a Neogene back-arc basin that opened during continental rifting and oceanic spreading related to the eastward migration of the Apennine subduction system from Tortonian to Pliocene times (Jolivet et al., 2006). Rifting of the Tyrrhenian Sea started first along the Eastern Sardinian margin during the Tortonian-Messinian times and therefore the series of that age should be considered as syn-rift sediments (Sartori et al., 2004). The « METYSS » seismic profiles clearly illustrate that this part of the Tyrrhenian was highly segmented during the rifting stage by N-S trending normal faults delineating ridges (e.g., Baronie Ridge) and basins (e.g., Sardinian Basin and Cornaglia Terrace), as previously described for example by Thommeret (1999) and Sartori et al. (2004). The Messinian sedimentary units and especially the « Upper Unit » (UU, Lofi et al., this congress, corresponding to the « Upper Evaporites » in the previous literature) are, without any doubt, of syn-rift age, as they display a fan-shaped stratal geometry. The Mobile Unit (MU, Lofi et al., this congress), i.e. the Messinian halite, is clearly imaged in the study area and its spatial repartition can be outlined. The highly-variable thickness of the confined salt basins could be due to the initial basin geometry (i.e. before the Messinian salinity Crisis) or to the syn-rift character of the deposition. Southeastward of the study area, in the vicinity of the Cornaglia Seamount, salt tectonics appears surprisingly vigorous. More surprisingly, several normal faults seem to have remained active in recent times, if not even at present time. Fault slip has been recorded by bathymetric scarps and associated footwall debris flows interfingered within the Plio-Quaternary sequence, even though the eastern Sardinian margin is usually considered to be passive now. Moreover, some amount of tectonic inversion is visible on some normal faults that show contractional or transpressional components of late slip. In addition, this “post-rift” deformation can be illustrated within the Plio-Quaternary sequence by a regional unconformity. Consequently, numerous mass-transport deposits and channel-levees systems observed in the Plio-Quaternary cover could be partly controlled by tectonic activity. These very preliminary results require further investigations in order to better decipher the role of crustal tectonics and salt tectonics, salt-related structures being very efficient markers to discriminate between the respective contribution of gravity-driven, salt tectonics and deep-seated, crustal tectonics (Gaullier et al., 2010). Finally, we aim to precisely determine the relative vertical movements (tilting, subsidence, magmatism. . . ) and geodynamical history of the different segments of the area since 6 Ma.
Geophysical Research Abstracts
Vienne, Austria

hal-00537828
https://hal-brgm.archives-ouvertes.fr/hal-00537828
https://hal-brgm.archives-ouvertes.fr/hal-00537828/document
https://hal-brgm.archives-ouvertes.fr/hal-00537828/file/EGU2010-15469_ref6821.pdf