Éditeur(s) : HAL CCSD Oxford University Press (OUP): Policy B - Oxford Open Option A
Résumé :  
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called the G-layer, in the fibre cell wall. The structure of the G-layer has recently been described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2-50 nm). This led us to revisit the concept of the G-layer that had been, until now, only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with a typical thick G-layer while it is much less with a thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without a G-layer is as low as in normal wood. Not depending on the amount of pores, the pore size distribution is always centred around 6-12 nm. These results suggest that, among species producing fibres with a G-layer, large structural differences of the G-layer exist between species.
Journal of Experimental Botany

hal-01032161
https://hal.archives-ouvertes.fr/hal-01032161
DOI : 10.1093/jxb/erp133

Éditeur(s) : HAL CCSD Elsevier
Résumé : International audience
Wood has a hierarchical structure involving several levels of organisation. The stiffness of wood relies on its capacity to transfer mechanical stress to its stiffest element at the lowest scale, namely crystalline cellulose. This study aims at quantifying to what extend crystalline cellulose contributes to wood stiffness depending on its moisture content. The crystal strains of cellulose were measured using X-ray diffraction on wet and dry specimens of spruce, based on a previously published methodology. The comparison between crystal strain and macroscopic strain shows that, during elastic loading, cellulose strain is lower than macroscopic strain. The means ratio of crystal/macroscopic strain amounts 0.85 for dry specimens and 0.64 for wet specimens. This strain ratio cannot be explained just by the projection effect due to the difference in orientation between cellulose microfibrils and cell wall, but results from deformation mechanisms in series with cellulose. Analysis shows that this series contribution represents a non-negligible contribution to wood compliance and is strongly moisture-dependent. This contribution amounts 9% for dry specimens and 33% for wet specimens, corresponding to a 4-fold increase in compliance for the series contribution. The origin of these strains is ascribed to mechanisms involving bending or shear strain at different scales, due to the fact that reinforcing element are neither perfectly straight nor infinitely long.
ISSN: 0266-3538

hal-01425031
https://hal.archives-ouvertes.fr/hal-01425031
https://hal.archives-ouvertes.fr/hal-01425031/document
https://hal.archives-ouvertes.fr/hal-01425031/file/Art_Almeras_al_Contribution_cellulose_moisture-dependent_elastic_behavior_2017.pdf
DOI : 10.1016/j.compscitech.2016.11.025

Éditeur(s) : HAL CCSD Oxford University Press (OUP)
Résumé : International audience
The mechanism for tree orientation in angiosperms is based on the production of high tensile stress on the upper side of the inclined axis. In many species, the stress level is strongly related to the presence of a peculiar layer, called G-layer, in the fibre wall. The structure of G-layer has been recently described as a hydrogel thanks to N2 adsorption-desorption isotherms of supercritically dried samples showing a high mesoporosity (pores size from 2 to 50 nm). This led us to revisit the concept of G-layer that was until now only described from anatomical observation. Adsorption isotherms of both normal wood and tension wood have been measured on six tropical species. Measurements show that mesoporosity is high in tension wood with typical thick G-layer while it is much less with thinner G-layer, sometimes no more than normal wood. The mesoporosity of tension wood species without G-layer is as low as in normal wood. Not depending on the amount of pores, the pore sizes distribution are always centred around 6-12 nm. These results suggest that, among species producing fibres with G-layer, large structural differences of G-layer exist between species
ISSN: 0022-0957

hal-00387861
https://hal.archives-ouvertes.fr/hal-00387861
DOI : 10.1093/jxp/erp133

Éditeur(s) : HAL CCSD Fayard/Arthème
Résumé : La biomécanique des plantes est née d'une approche interdisciplinaire. Elle regroupe ainsi des biologistes, des forestiers ou des agronomes, et des mécaniciens (des matériaux et des structures et plus récemment des fluides). Elle s'intéresse à la façon dont les plantes se portent et croissent. En particulier comment les plantes terrestres croissent en hauteur " contre " la gravité et dans le vent ; mais aussi comment les plantes aquatiques et les algues se développent dans les courants.
Aux Origines des Plantes

hal-00795935
https://hal.archives-ouvertes.fr/hal-00795935
https://hal.archives-ouvertes.fr/hal-00795935/document
https://hal.archives-ouvertes.fr/hal-00795935/file/BiomA_canique_plantes_Fournier_Moulia_Gril.pdf

Éditeur(s) : HAL CCSD
Résumé : International audience
A key element of the biomechanical design of trees is their ability to generate largemechanical stresses in wood at the stem periphery. This function is necessary for the tree tocontrol the orientation of its axes, and therefore to grow in height, maintain its branches at anoptimal angle or achieve adaptive reorientations (Fournier et al., 2013). This “maturationstress” appears in wood fibres during their cellular maturation when their secondary cell wallis thickening. In hardwoods, the stress asymmetry is generated by the formation of specificfibres with a very high tensile growth stress on the upper side of the inclined axis. Theresulting tension wood has microstructural features highly different from the normal wood.Tension wood in almost all temperate species has a specific gelatinous cell wall layer, calledG-layer, that is not lignified and highly mesoporous (Chang et al., 2015). It has been shownrecently, at the macroscopic scale, that cellulose tension appears during maturation and issynchronous with the development of this specific layer (Clair et al., 2011). Tropical species,like simarouba, are able to generate lignified tension wood fibres. The mechanisms of stressgeneration in tension wood fibres are not yet well known. The aim of our study is tounderstand these mechanisms and to know the spatial and temporal kinetics of the differentcell wall layers stiffening during maturation, in parallel with tensile stress generation.Contact-Resonance Atomic Force Microscopy, CR-AFM, was used here to address thisquestion on embedded samples (Arnould and Arinero, 2015) using dual resonance frequencytracking (DRFT, Rodriguez et al., 2007). Change in the contact modulus between, and within,each layer of the cell wall has been measured on several radial lines of developing fibres atdifferent steps. In order to understand the obtained results, and to estimate the sensitivity ofthe AFM indentation-like technique to the different cell wall components stiffness, an elasticanisotropic indentation model was used (Vlassak et al., 2003; Jäger et al., 2011). Finally,these mechanical measurements have been compared to topochemical data obtained on thesame fibres.
8th Plant Biomechanics International Conference
Nagoya, Japan

hal-01436113
https://hal.archives-ouvertes.fr/hal-01436113

Éditeur(s) : HAL CCSD Wiley
Résumé : International audience
In order to progress in the understanding of mechanical stress generation, the mesoporosity of the cell wall and its changes during maturation of poplar (Populus deltoides x P. nigra) tension wood (TW) and opposite wood (OW) were measured by nitrogen adsorption–desorption. Variations in the thickness of the gelatinous layer (G-layer) were also measured to clarify whether the mesoporosity change simultaneously with the deposition of the G-layer in TW. Results show that mesoporous structures of TW and OW were very similar in early development stages before the deposition of G-layers. With the formation of the S2 layer in OW and the G-layer in TW, the mesopore volume decreased steeply before lignification. However, in TW only, the decrease in mesopore volume occurred together with the pore shape change and a progressive increase in pore size. The different patterns observed in TW revealed that pores from G-layers appear with a different shape compared to those of the compound middle lamella, and their size increases duringthe maturation process until stabilising in mature wood. This observation strongly supports the hypothesis of the swelling of the G-layer matrix during maturation as the origin of maturation stress in poplar tension wood.
ISSN: 0028-646X

hal-01081834
https://hal.archives-ouvertes.fr/hal-01081834
https://hal.archives-ouvertes.fr/hal-01081834/document
https://hal.archives-ouvertes.fr/hal-01081834/file/Chang_al_Mesoporosity_changes_New-Phyto._2015.pdf
DOI : 10.1111/nph.13126

Éditeur(s) : HAL CCSD Public Library of Science
Résumé : International audience
Domestication can influence many functional traits in plants, from overall life-history and growth form to wood density and cell wall ultrastructure. Such changes can increase fitness of the domesticate in agricultural environments but may negatively affect survival in the wild. We studied effects of domestication on stem biomechanics in manioc by comparing domesticated and ancestral wild taxa from two different regions of greater Amazonia. We compared mechanical properties, tissue organisation and wood characteristics including microfibril angles in both wild and domesticated plants, each growing in two different habitats (forest or savannah) and varying in growth form (shrub or liana). Wild taxa grew as shrubs in open savannah but as lianas in overgrown and forested habitats. Growth form plasticity was retained in domesticated manioc. However, stems of the domesticate showed brittle failure. Wild plants differed in mechanical architecture between shrub and liana phenotypes, a difference that diminished between shrubs and lianas of the domesticate. Stems of wild plants were generally stiffer, failed at higher bending stresses and were less prone to brittle fracture compared with shrub and liana phenotypes of the domesticate. Biomechanical differences between stems of wild and domesticated plants were mainly due to changes in wood density and cellulose microfibril angle rather than changes in secondary growth or tissue geometry. Domestication did not significantly modify "large-scale" trait development or growth form plasticity, since both wild and domesticated manioc can develop as shrubs or lianas. However, "finer-scale" developmental traits crucial to mechanical stability and thus ecological success of the plant were significantly modified. This profoundly influenced the likelihood of brittle failure, particularly in long climbing stems, thereby also influencing the survival of the domesticate in natural situations vulnerable to mechanical perturbation. We discuss the different selective pressures that could explain evolutionary modifications of stem biomechanical properties under domestication in manioc.
PLoS ONE

halsde-00917926
https://hal.archives-ouvertes.fr/halsde-00917926
https://hal.archives-ouvertes.fr/halsde-00917926/document
DOI : 10.1371/journal.pone.0074727

Éditeur(s) : HAL CCSD Walter de Gruyter
Résumé : absent
Holzforschung

hal-01031939
https://hal.archives-ouvertes.fr/hal-01031939
DOI : 10.1515/HF.2005.057

Éditeur(s) : HAL CCSD
Résumé :  
The gelatinous layer (G-layer) of tension wood fibres in hardwood contributes to the mechanical function of the living tree and has significant consequences on properties of solid wood. Its size, shape and structure observed by optical or electron microscopy exhibits characteristic anatomical features. However, we found that sectioning of non-embedded wood samples results in an uncontrolled swelling of the G-layer was monitored by serial sections, from an embedded wood sample, from its trimmed transverse face to that located several hundreds of micrometers deep. The results revealed that the initial cutting before embedding produced a border effect responsible for the swollen nature, which is similar to sections from non-embedded material. After a conventional embedding technique was applied, a section of at least 30 micrometres below the trimming surface is required to observe an un-swollen G-layer.
IAWA Journal

hal-01032054
https://hal.archives-ouvertes.fr/hal-01032054